Search Documents

By Floyd JM

Pilot plant trials showed the effective ness of the submerged lance SIROSMELT technology for altering the composition of iron blast furnace slags as a preliminary step to produc- tion of formed materials. Mixtures of oil and air were injected into a bath of liquid slag to provide the heat required for melting the additives and to provide very turbulent conditions which resulted in complete dissol- ution of added fluorspar within one minute and almost complete dissolution of silica in two minutes. Sulphur lost during injection was readily made up by addition of pyrite or pyrrhotite. A stable foam could be readily made and broken down and the foamed slag appeared suitable for extrusion or forming into shapes.

Jan 1, 1979

By Williams P. A

Tailings dams constructed by the upstream method have traditionally been built using the sand fraction of the tailings, which has automatically provided a relatively permeable embankment material, and helped provide the necessary drainage conditions which are a pre-requisite for safe and stable dam construction using this method. This paper discusses some recent trends which have resulted in proposals to use impermeable material in place of the sand fraction as the embankment material, both for the starter dam, and subsequent lifts. The consequences of these types of decisions on the overall stability of the dam are illustrated, and the need for continued monitoring of pore pressures in the tailings as the dam is raised is emphasised.

Jan 1, 1992

Solid EnergyÆs project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholdersÆ risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

Evaluation of tyre chains has been taking place at King Island Scheelite for several years. Results indicate that tyre life has been greatly improved in all cases. Good cost sav- ings are resulting on small loaders. The worth of chains is difficult to prove on larger loaders under the conditions at King Island Scheelite. However, the dramatic decrease in the number of punctures has convinced the Company that chains are worthwhile on some larger loaders.

Jan 1, 1977

The excessively high cost of production in underground coal mines has made the survival of many coal mines around the globe economically non-viable. The global competitive coal market speaks itself of the desirability of a lower operating cost in conjunction with a higher productivity performance, particularly in underground coal mines, and calls for an optimal production planning under a host of constraints. Such a task of optimal planning is not an easy exercise like that of traditional planning based merely on intuition, experience and subjective judgement. It essentially demands a thorough understanding of the complex interaction of mine sub-systems for judicious application of optimisation tools and techniques available with operations research. A few large mines around the globe have made an effective use of a sizeable number of operations research packaged programs for optimal decision-making (Grayson, 1989). The success of practical applications of operations research techniques made in a variety of mining problems in large mines in different parts of the world will hopefully make inroads to smaller mines in years to come. The present paper is an addition in the series of such applications of operations research tools to mining problems, particularly with reference to an underground coal mine in India. The paper is based on research work (Jawed, 1990) and deals with the development and use of a mathematical model for production planning in underground coal mines under multiple objective environment subject to a host of constraints.

Jan 1, 1995

The Musselwhite mine, located in northwestern Ontario, Canada, has been an underground narrow-vein gold producer since the spring of 1997. As an exploration project at the feasibility stage, much effort was undertaken to generate a geostatistical resource model that would integrate the orebodyÆs geological features, as well as the controls on mineralisation. Today as an operating mine producing over 200 000 ounces of gold per year, reconciliation studies of the tonnes and grades treated at the mill, with the feasibility model, for longer time periods, and with the grade control models, for shorter time periods, show results that are in good agreement. It was clearly demonstrated with the reconciliation to production, that the key to good reconciliation remains in the proper selection and application of the geological resource estimation method. The application of a grade interpolation technique capable of capturing threedimensionally pertinent geological features, as well as accounting for spatial grade continuity, proved to be successful in the predictability of tonnage and grade at the Musselwhite mine. Along with good mine practices, this approach, which was carried through to the operation, has produced excellent reconciliation results. The ongoing reconciliation studies at Musselwhite allow for a constant revision of the grade estimation strategy. In return, this optimisation process adds value by raising the accuracy level of production expectations. As this is an evolving practice at the mine site, further implementation developments are recommended to integrate these reconciliation procedures on a more regular basis.

Jan 1, 2002

By E A. Agorhom, P N. Aabulleh

The bulk of the worldÆs production of iron ore is processed into steel. The needs of the steel industry therefore demand a high exploration and exploitation of iron ore. One trend within the industry has been a great increase in the demand of iron ore and this is reflected in an increase in world steel production from 1955 to date. In addition to the high demand for steel, is ChinaÆs high appetite to feed its steel industry. It is therefore important that the iron ore potential of Ghana is showcased for eventual exploitation by potential investors to meet this enormous demand for the commodity in the industry globally. Ghana has three main iron deposits of potential industrial and commercial importance. They are: Shieni sedimentary iron ore (reserves: 1.270 X 106 metric tonnes), Pudo titaniferous-magnetiferous iron ore and the Opon-Mansi lateritic iron ore deposits. The Opon-Mansi iron ore deposit occurs in the Western region of Ghana. The ore deposits are located on top of the range of 15 hills, which extend over a distance of 24 km from Opon-valley, south of the Western region to Dunkwa. The area has an estimated 147 Mt of iron deposit, with Fe content of 52.5 per cent. This paper looks at the iron ore potential of Ghana and how it is capable of attracting potential investors to exploit this valuable mineral for global consumption.

Jan 1, 2007

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By I D. Hair

A numerical groundwater model was used to predict the nature of interactions between heavy mineral sands mining operations and the groundwater regime at North Stradbroke Island, Southeast Queensland. North Stradbroke Island is formed mainly of massive vegetated Cainozoic aged dune sands. Since the 1950s, a number of operations have mined rutile, zircon and ilmenite on North Stradbroke Island. In such mining operations, a dredge and an associated processing plant are floated in a pond either above or below the prime groundwater table The numerical model was based on the North Stradbroke Island Groundwater Management Model, developed in 2001 by the Department of Natural Resources and Mines (NR&M). This model was constructed using the modular, cell-centred, finite-difference groundwater flow model, MODFLOW, developed by the United States Geological Survey (USGS). The NR&M model was refined to improve model resolution and detail for simulating dredge mine paths. Of particular interest were: water table fluctuations induced by mining for the identification of slope stability risk; the optimisation of sand spear arrays supplying mine make-up water requirements; inflow and outflow rates to the dredge pond for overall mine water balance; and interactions with Eighteen Mile Swamp and water supply bores controlled by the Redland Shire Council (RSC). Depending on the water level in the dredge pond compared with the surrounding groundwater table, water either flows out of the dredge pond into the groundwater regime or from the groundwater system into the dredge pond. The MODFLOW river package (RIV) was utilised for the modelling study. Dredge pond movement was simulated using specialised software developed by Watermark Numerical Computing (WNC) to interpolate pond positions and map the dredge path to the model grid both spatially and temporally. As tailings placement affects the groundwater system through increased recharge, the MODFLOW recharge package (RCH) was utilised to simulate different recharge efficiencies. Long-term model predictions were made for the period from July 2002 to May 2021. Results of the modelling showed that exchanges of flow between mining operations and the groundwater regime could be effectively managed. The study provided valuable information which was used to develop an appropriate mine water management plan.

Jan 1, 2003

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

Distal rhyolitic tephras from the Taupo Volcanic Zone are widespread in the Auckland urban region. Some are primary air fall or flow deposits but most are reworked. Their presence indicates potential hazard for the Auckland urban region from future eruptions of central North Island volcanoes and associated secondary effects. Geotechnical problems occur as a result of weathering of the tephras yielding sensitive materials.

Jan 1, 1990

Topography, location of coal bearing land and existing built-up areas severely restrict locations for overburden disposal and dumping sites north of the Latrobe River clear of the coalfields are assumed until internal dumping areas can be established.

Jan 1, 1982

By Hu Y, Li D, Qu G

In this paper the structural mechanism of the gold - lixiviant complex is investigated. The results show that there are two common characteristics in the outer orbitals for all the gold lixiviants: a) a (Y -type of HOEO to form the L-*Au co-ordination bond, and b) a it type f LUEOs, with symmetry the same as that of 5d orbitals of Au, to form L

Jan 1, 1993

By Ross C

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

By R M. Briggs, I E. Smith, P M. Black, A B, R L. Brathwaite, J L. Mauk

The Hauraki Volcanic Region of the North Island developed between 18 and 1.9 Ma. Initial andesitic volcanism from 18 to 12 Ma was followed by 12 to 1.9 Ma volcanic activity that included rhyolitic, dacitic, andesitic, and basaltic compositions, with a gradual migration of activity to the SSE. Early andesitic volcanism evolved over the course of 8 m.y. to more silicic compositions; this trend was reset and repeated by post-10 Ma andesitic volcanism. Early and later andesites are otherwise remarkably similar in trace element composition. Rhyolites have the most diverse compositions, suggesting a major role for crustal input in their formation.

Jan 1, 2007

By Tiu C, Sarmiento G, Uhlherr PHT

Fundamental rheological properties of slowly settling mineral slurries are reviewed. Slurry flow is discussed in terms of observed shear stress-shear rate behaviour. Particular emphasis is placed on establishing procedures for scale-up and design. Flow property measure- ments on red mud, a waste product from the Bayer alumina process, are presented and used to illustrate recommended design procedures.

Jan 1, 1978

Extensive geophysical exploration and drilling operations have been: conducted in, South Central Queensland by Phillips Petroleum Company and Sunray DX Oil Company since late 1959. The main outlines of subsurface geology are now known, but many problems must be solved before a comprehen sine. picture can be presented of the geology and petroleum prospects e Interpretations to date suggest that -fiddle Paleozoic sedimentary rocks, probably, related to the Tasman belt of geosynclines, once extended. over. most. of the area An oro;eny 2.n late Paleozoic time, succeeded by deep pre-Pexmian erosion, removed the older sediments over large. areas, but Paleozoic sediments, were preserved from erosion in the Adavale and ancillary structur-a.l basins. Marine sediments of Devonian age are con-sidered prospective source beds for petroleum. Current work is directed toward finding favorable structure and reservoir beds to test the oil prospects of the area.

Jan 1, 1962

It is extraordinary that while Australia depends heavily on mineral wealth for its economic well-being, most Australians have no appreciation of the traditions and principles which drive and govern the mineral industry. Their understanding has been largely provided by those who campaign against the industry in one way or another and is therefore quite unrepresentative.

Jan 1, 1993

By Zhijing Z, Huiling Z

The influences on flotabilities of dolomite and magnesite with modifiers and influences on the function of collectors and modifiers with Mg+z Ca+2 were studied. The flotation results of artificial mixed mineral showed that using combined salified water glass and (NaPO3)6 as a modifier for magnesite-dolomite separation can obtain an excellent Selectivity.

Jan 1, 1993