Search Documents

By J Kwiri, T Zvarivadza, R Mitra, F Cawood

It is crucial to record ground movement of any magnitude to enable the safe and economical design of excavations and infrastructure. The DigiMine Laboratory is equipped with technologies to record such movements. This paper analyses the effectiveness of the Digital Mine instrumentation in recording earth movements in light of the Botswanan earthquake which occurred on the 3rd of April 2017 at 17:40 UTC. Recordings from the Digital Mine are compared with other ground sensing technologies which also captured the event (USGS and GEOFON systems). USGS and GEOFON system’s recordings suggest that, there are a number of possible mechanisms that could have resulted in the earthquake as discussed in the paper. Compared to the USGS and GEOFON systems, DigiMine system could not provide an analysis that could give possible source mechanisms. However, the system’s success in recording the Botswanan earthquake, is an indication that the system works and can be further developed or improved. For a comprehensive analysis, more data from various sensors needs to be collected. For example, DigiMine connecting to the national seismic monitoring system or to the local mine’s seismic monitoring system. Such connections will enable the development of a better self-analysis system and possibly prediction of future events. More importantly, it will contribute to better understanding of regional seismicity and its potential impact on excavation design. CITATION:Kwiri, J, Zvarivadza, T, Cawood, F and Mitra, R, 2018. How efficient is DigiMine technology in recording earth movements? A look at the Botswanan earthquake, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 414–419 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Yang RL, Bailey ML

During overburden blasting operations in dragline pits, coal edge losses along the lowwall edge of the new pit are often experienced. In tonnage terms, losses can be significant. With the thick seams at Callide Mine, 20,000 tonnes of coal can be lost along a 600 metre pit. In addition to the immediate dollar value of the coal, replacement of this coal (from which overburden has been removed) will be from higher ratio and higher cost pits in the future. Unit costs of production for the remainder of the coal uncovered in the current pit increase. Experiments involving variation of blasthole inclination and/or amount of standoff on the front row of blastholes have given no significant improvement in the coal edge loss control.

Jan 1, 1988

Powercoal Pty Ltd operates eight underground coal mines in New South Wales and produces coal for both domestic power stations and the export market. Approximately 40% of total production is from continuous miners. Over the past five years, place change mining methods have been introduced to improve productivity from continuous miners. This has involved utilising the existing coal clearance system from the continuous miner to the ratio feeder using trailing cable shuttle cars.By late 1996 average productivity at Cooranbong Colliery using this system had plateaued at 800 tonnes per eight hour shift. A number of factors were identified to increase average productivity to 1500 tonnes per eight hour shift. An improved coal clearance system was one of the factors identified.

Jan 1, 1998

By K Grohs, A Satriawan, S R. Pearce

Martabe gold and silver mine is operated by PT Agincourt Resources (PTAR) and is situated in northern Sumatra and comprises several deposits in steep terrain, and in a tropical climate, that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste rock from excavations and tailings from processing is a by-product to be scheduled and used for a number of purposes identified as part of life-of-mine planning. These uses include construction of the current integrated tailings storage facility (TSF) as well as future engineering construction and waste disposal projects which includes plans for a program of in-pit backfilling. These plans need to be aligned to ensure the waste rock and tailings can be contained relative to the production rate. Given that the site will have multiple open pit voids upon cessation of mining activities opportunities for integration of in-pit disposal of mine waste have now been assessed with technical studies to review the practicality of the approach with respect to operational challenges and conformance with closure planning requirements. This includes assessment of disposal of waste rock, tailings (including consideration of filtered tailings) and co-disposal of waste rock and filtered tailings.

Aug 2, 2023

By P B. Swart, P D. Erskine

Despite an increasing focus by media, communities and activists driving an elevated regulatory focus in Australia and indeed some other mining jurisdictions, the mining industry globally has had limited successful mine lease relinquishments and transfers to support a next land use.Critique from anti-mining lobbyists frequently uses the large estimates from historically abandoned mine sites to influence risk-averse regulatory reforms to improve environmental performance. The mine rehabilitation regulatory processes in Australia, and specifically in the State of Queensland, are thus largely in place to prevent mining operators from abandoning their obligations.Regulatory responses to the lack of mine rehabilitation and closure performance in the last five to ten years have primarily focussed on compliance and enforcement of rehabilitation conditions in environmental approvals. Additionally, financial assurance measures have been tightened to protect against abandonment of rehabilitation obligations by the Industry, including the Chain of Responsibility legislation (Queensland Government, 2016b) in April 2016, to hold to account those who have benefitted from mining and processing/refining projects, and then avoid their environmental obligations.CITATION:Swart, P B and Erskine, P D, 2018. Are our closure planning and regulatory processes adequate to identify, quantify and appropriately transfer residual risks after successful mine rehabilitation?, in Proceedings Life-of-Mine 2018, pp 155–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By S Withell, K Sheehan

Whitehaven Coal (WHC) is undergoing a transformative journey, deeply committed to the principles of a High Reliability Organisation (HRO) and the establishment of a mature, interdependent culture founded on psychological safety. This ongoing commitment is not merely aspirational but is supported by performance improvements backed by both quantitative performance data and qualitative evidence of cultural progression. WHC has strategically integrated leading and lagging indicators to target fatal risk. WHC focus areas include an emphasis on strategy and risk appetite, targeted data, informed learning, proactive addressing of fatal risk and the integration of data management and technology.

Apr 16, 2024

By R Peiffer, L van Wyk

The Port of Port Hedland is the largest bulk export terminal in the world and is one of Australia’s most important pieces of economic infrastructure. BHP is the largest Port user to support the export of iron ore products from mines located within the Pilbara region of Western Australia (WA). BHP’s priority is the safety and well-being of its workforce and the communities where it operates. In a recent regulatory application to increase export capacity, BHP committed to the deployment of wind fences to reduce wind erosion from stockpiled ore. Wind erosion from stockpiles was identified through inverse modelling as the most significant dust source compared to other sources such as stackers, reclaimers, shiploaders and transfer stations. The primary cause of dust emissions from stockpiles is dust lift-off during high wind conditions. BHP proposed the installation of wind fences across its Port Hedland operations, targeted at reducing emissions from wind dependent sources, primarily stockpiles, by reducing the wind speed downwind of the wind fence. Modelling predicts that installation of the wind fence will significantly reduce emissions from stockpiles, particularly at BHP’s western operations (Finucane Island). To be effective in shielding stockyards and reducing wind speeds, the wind fences are located upwind and as close as practical to the open stockyards. BHP’s wind fence design incorporates learnings from other existing installations and has been tailored for Port Hedland’s cyclonic conditions. The wind fence will be higher than the stockpile height, with a mesh porosity of approximately 50 per cent. The mesh porosity allows some of the wind to pass through the mesh. This reduces the wind turbulence downstream of the wind fence, as opposed to a solid wind fence, which increases downwind turbulence, resulting in increased dust.

Sep 18, 2023

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

By R Valenta, I Fahey, M Klawitter, N Spanswick

Zinc-Lead-Silver (Zn-Pb-Ag) mineralisation at the George Fisher Mine occurs in multiple structurally-disrupted stratiform orebodies hosted within a mid-Proterozoic sequence of calcareous siltstones and variably pyritic shales (e.g. Valenta, 1994; Chapman, 2004). The geological model for the mine has been constructed based on a large number of stratigraphic domains which have been defined using recognised patterns of the constituent rocktypes, aided by recognition and mapping of K-rich tuff marker beds (TMBs). The continuity of these domains has been affected by the presence of several sets of faults which are extensional in the plane of stratigraphy, leading to the common occurrence of fault-related stratigraphic gaps in drillholes. Recent improvements to the detail of the geological model have led to significant improvements in the head grade of ore at George Fisher, with relatively small loss of metal. Recognition and accurate logging of these domains requires a high level of knowledge and expertise amongst mine geologists. In order to aid this process, the George Fisher mine installed a Minalyzer CS (core scanner) on site, with the aim of using high resolution X-ray fluorescence (XRF) geochemical data and core photography to increase the speed, accuracy and consistency of the site geological logging system. This contribution describes some preliminary results from a research project aimed at using the Minalyzer CS XRF data to perform high-resolution rocktype identification and domain boundary mapping in drillcore at George Fisher. CITATION: Spanswick, N, Klawitter, M, Valenta, R and Fahey, I, 2018. Rocktype classification and domaining of complex stratiform Zn-Pb-Ag mineralisation at the George Fisher Mine using high resolution XRF Core scanning, in Proceedings Complex Orebodies Conference 2018, pp 58–59 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By H Kurth

Oyu Tolgoi copper and gold mine in the southern Mongolia holds mineral resources that make it one of the largest known copper and gold deposits in the world. The project is operating an open pit mine on the near surface of Southern Oyu deposit and developing underground block-caving mine at the Hugo Dummet North where 80 per cent of total resources exists. Oyu Tolgoi (OT) commenced open pit mining in 2011 and implemented an industry standard blasthole sampling, and ordinary kriging grade control estimation with block-out process. Since 2017, grade control improvement projects have successfully completed that have led to the implementation of current, improved grade control system. Geological model is updated by blasthole logging on Leapfrog® and used for daily grade estimations. GC estimation is proceeded solely on Vulcan® by running Lava script and integrating with a relational database. Combination of block-out procedure produces GC model which is updated in Vulcan® and as well as in the database simultaneously. Switching to the integrated database eliminated many manual processes such as importing and exporting data and enabled access to the database anytime, anywhere and from any device. Thereby, these improvements allowed to increase an efficiency, create a comprehensive reconciliation system and reduce operational risks. We are looking forward to expanding applications of integrated grade control data stored in the database. This paper outlines how the grade control system was developed at OT’s open pit mine, and how it is integrated into the short range mine planning, mine reconciliation workflow and ultimately enabled development of various automated reporting systems.

Mar 22, 2022

By M McCurd, M Lynch, B H. Yin, S Mendoza, C W. Bumby, Y Iwasaki, B Rumsey

Iron and steel production is responsible for approximately 6.3 per cent of global anthropogenic CO2 emissions. Direct reduction of iron with hydrogen is a potential route for decarbonising the iron and steel industry. Extensive small-scale laboratory experiments have been performed to test the feasibility of hydrogen-direct reduction of iron ores sourced from diverse geographical locations. However, test results from the batch reduction of small-sample do not necessarily translate to continuous commercial-scale processes. Establishing a small-scale continuous test reactor for H2- DRI process is challenging, requiring substantial resources and investment. The limited availability of small-scale reactors that enable testing under relevant conditions has become a major obstacle for H2-DRI development, leaving a big gap between laboratory success and proof of commercial feasibility. Here, we report on the recent commissioning of a continuous counter-flow vertical shaft reactor, which has a processing capacity of 6 kg/hr iron ore pellets at up to 100 NL/min H2 flow. We believe this to currently be the largest H2-DRI facility in the Southern Hemisphere. In this talk, we will discuss the design and construction journey for this reactor, starting from the initial system design to the initial demonstration of H2 reduction of titanomagnetite ironsand pellets. This reactor now enables a range of research capacities, including the validation of laboratory results on a larger scale with practical operational variables, feasibility assessment of hydrogen direct reduction of different iron ores on a commercial scale; identification of scalability, sticking, and other potential issues before building a full-scale plant; and a viable solution for producing small-quantity DRIs for downstream melting investigations. Overall, this new research facility offers significant benefits for assisting the transformation of iron and steel production to a more sustainable and green industry.

Sep 18, 2023

New South Wales mining legislation reinforces a systematic approach to safety management. It is now a requirement of all mines in the coal, metalliferous and quarrying sectors in NSW to prepare a Mine Safety Management Plan. The paper briefly outlines work currently being undertaken by the Safety Operations Branch of the NSW Department of Mineral Resources (DMR). The DMR is working proactively with NSW mines in the preparation and implementation of effective Mine Safety Management Plans. There is a growing realisation that a systematic approach to safety management, underpinned by the process of hazard identification, has real potential to improve safety in the workplace. The paper briefly describes the framework used in a current æmines education programÆ and its æduty of careÆ foundation. Particular attention is paid to the role of mining operators in the implementation of Mine Safety Management Plans and their expected behaviour in demonstrating compliance. One challenge is convincing some mining operators that they must adopt new ways of working. Safety Operations officers are often reminded of the need to translate Mine Safety Management Plans into practical safety systems during audits and inspections of mines and through investigations into accidents and incidents. To have a real effect on the mineÆs safety performance, using these systems must be a normal way of going about a dayÆs work for all persons who work at the mine: not a safety manual collecting dust on the mine managerÆs bookshelf. Mine Safety Management Plans are important to mining operators. Not only will positive involvement in the development and use of safety systems ensure they meet their obligations under mining legislation, but it will also help prevent themselves or their workmates being injured or killed.

Jan 1, 2002

By G Gibson

Realising that current roadway development performance levels were unlikely to sustain new generation high-capacity (15 Mt/a) longwall mines then being planned, the Australian Coal Association Research Program (ACARP) established a Roadway Development Task Group (RDTG) in 2005 to develop a research strategy targeted at improving roadway development performance in Australian longwall mines. The initial phase of the project identified a number of factors that differentiated best practice mines from others, and proposed a multi-faceted research strategy encompassing both short- and long-term research initiatives, including:conducting regular benchmarking studies across the industry to identify factors contributing to improved performance and to monitor performance trends,conducting regular industry roadway development operatorsÆ workshops to facilitate the transfer of successful roadway development improvement initiatives throughout the industry and facilitate networking between development practitioners,development of alternative skin reinforcement and containment measures that would eliminate the use of steel mesh and enable face support systems to be fully automated,development of automated bolting and mesh handling systems that would enable operators to be removed from the immediate face area,development of a body of knowledge of industry roadway development practice,development of a web-based information management system to capture and transfer emerging developments in roadway development practice and technology,reviewing the Australian civil tunnelling and underground metalliferous mining sectors to identify practices and technologies that could potentially be utilised to improve roadway development performance, anddeveloping a new generation high-capacity mining system capable of +10 metres per operating hour for 20 or more hours per day (CM2010). The paper reports on the progress of the above initiatives and outlines strategies to continue the pursuit for improved roadway development performance.

Jan 1, 2008

By D Deb, R Pramanik

This paper presents a generalised methodology in smoothed particle hydrodynamics (SPH) framework to analyse dynamic failure process of rock mass having natural joint under blast-induced stress wave and expansion, and penetration of high pressure gaseous product. The necessary interactions of gas-rock are incorporated in the model which describes features of coupling between damage and plasticity in tension and compression respectively. A Drucker-Prager formulation of plasticity is used to model the behaviour of aggregate field and the Grady-Kipp damage model is employed for tensile strain. These two material behaviours are then brought together within the framework of interacting continua. The model relies on the Drucker-Prager plasticity surface to predict the dilatancy aspect of the material response and to account change of strength according to the strain rate effect. Three numerical examples are presented with rock joint and multiple blastholes.CITATION:Deb, D and Pramanik, R, 2015. Smoothed particle hydrodynamics modelling of blast-induced fracture processes in naturally jointed rock medium, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Coal has been mined in New South Wales for nearly 200 years and prior to 1970 the vast majority of this coal was mined from underground mines using bord and pillar or similar systems.Since 1970 there have been two notable changes in coal production trends in New South Wales as can be seen from Figure 1.1. The steady growth in coal mined by open cut methods. Open cut output grew from about seven per cent of the State's output in 1970/71 to 43 per cent in 1990/91.2. The steady growth in coal mined by the longwall method. longwall output grew from negligible amounts in 1970/71 to 48 per cent of underground production in 1990/91. mines operating longwall units produced 61 per cent of underground production in 1990/91.

Jan 1, 1992

A new two-metre column self-heating test procedure has been developed at the University of Queensland, which clearly shows the hot spot development phases that take place in bulk coal self-heating. The column results provide a more reliable indication of the self-heating propensity of coal than small-scale index tests. At the same time, off-gas evolution patterns associated with hot spot development are obtained, including the recognition of hydrogen evolution from oxidation at temperatures less than 80¦C. Subtle differences in off-gas evolution from self-heating between gassy and gas-drained coal are also apparent. This new approach to coal self-heating assessment offers an opportunity to further the understanding of the complexities of spontaneous combustion and will enable more accurate risk assessment for the coal industry.

Jan 1, 2005

By A Millar, B Wraith

Process plants are characterised by variability of performance over a wide range of time-scales; reflected in fluctuations in metal recovery, concentrate grade, plant throughput and reagent costs. In turn, these fluctuations impact financial metrics such as operating costs and revenue. The primary cause of plant variability is variation in the physical, lithological and mineralogical characteristics of the ore fed to the plant. The variability of the ore is driven by the intrinsic heterogeneity of the geology and mineralogy of the orebody, the mining method and mine production plan, the capacity to stockpile and blend, as well as the plant flow sheet and the level of plant automation. Whilst the impact of ore variability on process plants is universally recognised, it is rarely quantified in financial terms. Consequently, opportunities to reduce its impact are often overlooked due to the lack of a basis for a quantifiable cost-benefit analysis to justify improvement initiatives. This paper will present case studies using production data from the Renison tin concentrator and a zinc concentrator. These case studies demonstrate that as the standard deviation of plant head grade increases (as a proxy for ore variability), plant metal recovery subsequently reduces. The metal recovery is then converted into plant revenue losses, to quantify the economic impact of ore variability. The Renison case study demonstrated that whilst a very rare occurrence, revenue losses were as high as 34 per cent (relative to the baseline) when standard deviation was at its highest. The zinc concentrator case study demonstrated that revenue losses were as high as 6 per cent (relative to the baseline) when standard deviation was at its highest. Options are available for reducing and managing ore variability in the process plant. These options include changing mining practices so that the ore is fed to the plant with less variability, more advanced process plant control systems and the use of predictive geometallurgical models.

Aug 24, 2022

By B Ghahreman‐Nejad, M Munro

Design of embankment dams often requires seismic analyses, or an assessment of earthquakeinduced ground and dam movements. There are a large number of cases where earthquakes have triggered sliding and lateral spreading of embankments, resulting in excessive crest settlements. In some instances, liquefaction and embankment failure has occurred resulting in loss of containment. Hence, evaluation of the effects of earthquakes on embankment dams is a critical design aspect. This paper discusses the methods and the results of a seismic liquefaction assessment and deformation analyses of a tailings dam. The tailings dam consists of a perimeter earth core rockfill starter dam which has been raised using upstream construction methods. The embankment raises (formed by an upstream clay blanket and an all-in rockfill body) are constructed over the impounded tailings, which are potentially liquefiable. Extensive field and laboratory tests were undertaken to assess the liquefaction potential of the tailings, and also determine the material properties required for seismic stability and deformation analyses. Numerical modelling of seismic liquefaction and deformation was carried out using FLAC (Itasca 2016) to predict the magnitude and spatial variation of deformations that may lead to an uncontrolled release of tailings. Primarily based on a parametric assessment of UBCSand and Finn-Byrne constitutive models, the results of the analyses are presented and compared for evaluation.

Jul 1, 2021