Search Documents

CSA mine, which is a deep level copper operation, located 12 km north of Cobar, NSW, currently uses a top down stoping method, utilising cemented hydraulic backfill (CHF) to fill and stabilise the stoping void thus assisting the extraction sequence. The stope sequence then requires development back through the CHF stope so that the necessary infrastructure for the subsequent stoping, such as raise bore pads can be sited. The primary and secondary support installed in the CHF consisted of 100 mm thick fibrecrete from floor to floor with 7 + 2.4 m long resin support tendons installed at 1.5 m ring spacing. This support system relied on the resin achieving a quality bond with the CHF, and also the fibrecrete developing early structural strength due to the use of an accelerator. In addition to the delays in the excavation turn around time, it was felt that a superior support system could be designed. Such a system was designed; risk assessed, tested underground, and trialled in selective CHF digouts, and eventually signed off as the chosen support method in CHF digouts. This paper discusses the change from a passive support system used in CHF digouts to an active support system using Swellex bolts and weld mesh, which has provided an active support system, that is superior, faster to install, reduced the excavation turn around time and is overall a cheaper support system.

Nov 25, 2010

Except for uranium search, conventional oil well logging techniques are relatively little-used in mining exploration. The main reasons for this are cost and an apparent lack of awareness of the potential use of the methods in the search for ore. However, relatively inexpensive portable units are currently available for performing the simpler electrical and radiometric logs in diamond drill holes.The emphasis in oil exploration logging programmes is largely on the estimation of porosity. In most mineral work, however, porosity is not very significant, and factors such as mineral conductivity and radioactivity assume an important role.The Bureau of Mineral Resources (BMR) during a programme to explore for uranium and associated base metals in the area east of Rum Jungle, N.T., carried out electrical and radiometric logging of diamond drill holes as a routine part of their investigations. Case histories are described in which the logs were used to aid in defining stratigraphic sequences and transgressive structures in base-metal prospects. Some surface geophysicalanomalies were explained by the logging: induced polarization and electromagnetic anomalies were related to black slate; and self-potential anomalies were related to oxidation of pyrite black slate, or apparent electrokineticeffects in the black slate. The logs provided an objective appraisal of the rock units penetrated and thereby helped to differentiate lithologies.Borehole logging, including newer techniques such as downhole analysis, could be done in geological and geophysical investigations in other areas for a relatively small cost with a considerable potential gain of information.

Jan 1, 1978

Although the pattern of metamorphic zones south of the Thackaringa-Pinnacles Fault is much obscured by polymetamorphism, displacement of the orthopyroxene isograd by the fault agrees with the displacement of a horizon of "banded aplite" mapped by Andrews (1922). A dextral transcurrent component of 20,000 ft is indicated.INTRODUCTIONThe east-west Thackaringa-Pinnacles Fault (Andrews, 1922; King and Thomson, 1953), one of the major geological structures in the Broken Hill district, New South Wales, cuts across the general north-easterly strike of outcrops and fold structures of the Willyama Complex. The degree of shearing and recrystallization in its unusually wide crush zone and the manner in which adjacent rock units and structures have been dragged into conformity with its strike denote considerable movement on the fault. Information concerning the nature of this movement is of critical importance in the search for possible continuations or repetitions of lead-zinc mineralization south-west of Broken Hill.A transcurrent movement of 20,000 ft, with the southern block moving west, was estimated by Andrews (1922), who correlated prominent outcrops of "banded aplite" at The Pinnacles (north of the fault) and Big Hill (south of the fault). Displacement of this order, however, does not seem sufficient to explain the extent and character of the fault zone. Recent chemical and petrological studies of the banded aplites at The Pinnacles and Big Hill by Vernon (19B1) confirmed their similarity, but indicated an origin by metasomatic replacement of pre-existing folded and metamorphosed rocks. This raises the possibility that some...

Jan 1, 1965

The Chamber of Minerals and Energy of Western Australia Inc (CME) is the peak resources sector representative body in Western Australia. The paper gives a summary of the role and objectives of the CME, including its history, structure and key program areas. Particular attention is given to the role of the CME in the Eastern Goldfields of Western Australia. The paper details the types of CME membership that are currently in existence. The paper argues that a strong and vibrant CME is vital to secure the resources sectorÆs growth and development in future years.

Jan 1, 2006

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C MacDonald

There are many technologies available today in terms of fire and life safety in road tunnels. So many in fact that it is becoming more and more difficult for clients and contractors alike to determine what they want and what they need. From a clientÆs perspective, fire and life safety is about protection to its infrastructure and to the public at large. Conversely, the contractor is looking to meet its æfit for purposeÆ or ædeem to complyÆ requirements in the most economic and practicable way. Practices regarding fire and life safety in road tunnels have undergone a degree of transformation during the last decade or more throughout the world. This transformation has largely been driven by a series of catastrophic accidents such as the major fires in Europe including the Mont Blanc Tunnel, Tauern Tunnel, Saint-Gothard Tunnel, and now most recently in the CityLink Tunnels in Melbourne. International guidelines produced by organisations such as the Permanent International Association of Road Congresses (PIARC), the European Union, the International Tunnelling Association (ITA) and the US National Fire Protection Authority (NFPA) now provide clients, owners and designers with the tools required to define and specify the required fire and life safety systems in road tunnels. The majority of these tools are based on risk assessment and risk management. Recent road tunnel projects within Australia, however, have not referred solely to such guidelines. Clients have opted to prescribe different or additional fire and life safety requirements within the projectÆs technical specification documentation (project requirements), leaving designers and contractors with little room to implement alternatives or substitutions. Further, these project requirements are largely dictated by practice established on previous road tunnel projects within Australia. This paper looks at the current international guidelines and practices and undertakes a comparison with the EastLink tunnels in Melbourne and other road tunnels within Australia and makes assessment on whether Australian methods are the most appropriate for clients and contractors alike. Focus is directed to the key elements of fire and life safety such as:traffic envelope, barrier arrangements and emergency walkway provisions;deluge systems;drainage systems;fire rating requirements;tunnel ventilation systems;cross passage provisions;fire safety assessment;critical intelligence systems including help phones, CCTV, incident detection, tunnel signage, etc; andexternal tunnel control systems.

Jan 1, 2008

By D Mnller, J L. Mauk

The Oblaga Cu-Au skarn deposit and porphyry prospect is located in the south-eastern edge of the Gobi Desert in western Inner Mongolia. The deposit occurs within metamorphosed middle Paleozoic volcanic, plutonic and sedimentary rocks.   Ivanhoe geologists recognise eight main rock types in the area. Calcareous sediments include conglomerate, interlayered siltstone-sandstone, and limestone. Covering the calcareous sediments is a slab of thrusted biotite granite, and above it is rhyodacitic lithic tuff which, in places, is overlain by alluvial sediments. Various plutonic rocks and related intrusion breccias have intruded these units. Monzodiorite, quartz-monzonite and monzonite tend to form thin, high-angle intrusions and the youngest andesitic intrusions are generally wider and subhorizontal.   The Oblaga Cu-Au skarn, which occurs in the calcareous sediments, shows typical prograde and retrograde mineralogy. Petrographic studies show that prograde skarn minerals have been overprinted by retrograde skarn minerals, and original host rock minerals have been texturally obliterated and completely replaced. The mineralogy of the Oblaga skarn deposit is very similar to other Cu-Au skarn deposits worldwide.   Sericitic and minor chloritic alteration occurs throughout the study area and may relate to porphyry-style mineralisation. Generally, this alteration is not intense and most rocks have retained their original texture. Geochemical analyses suggest that K-metasomatism is not widespread at Oblaga. XRD analyses suggest an upward and outward transition from sericitic to chloritic alteration.   Comparisons between Oblaga and other porphyry Cu-Au deposits worldwide show that Oblaga has very similar characteristics to deposits that have undergone sericitic alteration. However, Oblaga is special because it also has relatively intense chloritic alteration, which is uncommon in other porphyry Cu deposits described in the literature.

Jan 1, 2005

By Parker A. J, Ruane M, Wadley L. G B

Copper, sulphur, nickel, cobalt, palladium, silver, and gold can be recovered from the copper sulphide precipitated from the "copper boil" of the Sherritt-Gordon nickel process used at Western Mining Corporation's Kwinana nickel <refinery. The method is based on an oxidative ammonia leach of copper, nickel, and the precious metals at temperatures below 40°C to produce, in part, elemental sulphur, in the residue. This is followed by heating to decompose thiosulphate and remove some ammonia with precipitation of some of the copper, palladium, gold, and silver. Addition of sulphur dioxide to pregnant liquor precipitates copper, as either Chevreul's salt or copper(I) ammonium sulphite, together with the remaining gold and silver. Less than 10 per cent of the dissolved palladium and less than 1 per cent of nickel and cobalt precipitate to this stage.In one option, the Chevreul's salt is dissolved in a solution of copper(II) sulphate, acetonitrile, and water to generate a solution of copper(I) sulphate. Gold and silver do not dissolve. The solution of copper(I) sulphate is thermally disproportionated by distilling acetonitrile to give exceptionally pure copper powder, with desirable characteristics for powder metallUrgy. Nickel, cobalt, and ammonium sulphate are recovered from the motherliquor of the Chevreul's salt precipitation by return to the Sherritt-Gordon process, where recovery procedures already exist. Palladium is recycled for eventual removal as a sulphide with the gold and silver.In the other option, solid copper(I) ammonium-sulphite is <thermally disproportionated in water at 150°C to copper powder.

Jan 1, 1978

By Baxter J. L

Post-tertiary training programmes have been designed and produced for geologists at different levels of understanding and expertise in the relationship between gold mineralization and shear zones. A workshop format was used as it allowed both clients and facilitators to participate in the learning process. Evaluation by facilitators and participants refined the workshop programme as an effective skills oriented learning process. The general observation is that post-tertiary training in small, interactive, practical, learning oriented groups is far better than lecture oriented short courses for developing skills based learning. The evaluation indicates that the process in post-tertiary training must include aspects which are both useful and used.

Jan 1, 1989

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

A good deal of experimental work has been done from time to time on the application of compressed air to the elevation of wet pulp. On account of the flat nature of most of our mill sites elevation of the pulp has to be provided for, and the various methods in vogue show considerable loss of time, in the replaceing of wearing parts. During the last two years the writer has carried out a great many experiments with a view of devising an elevator that will give continuous work with a minimum of wear.The results do not show a high efficiency for the power employed, but the lift is continuous in operation, very cheaply installed, and possesses no wearing parts. The lift was tried working in a bore hole of 8 in. diameter, but in many cases it is more convenient to sink a small well for the purpose. The result to date showed that the most efficiency was obtained when the depth of the wellwas not less than the height of the lift required. The pressure of air required in pounds per square inch was (approximately) half the number of feet to be lifted.In the majority of cases the lift required varied between 20 ft. and 50 ft. and the air pressure required between 10 lbs. and 25 lhs. per square inch. In most existing installations the air compressors in use were delivering air to the receivers at about four times that pressure, and when air so compressed was expanded to perform its work at a reduced pressure, it was apparent that the power exerted in origInally compressing the air above the working pressure required at the lift was absolutely lost.

Jan 1, 1901

Tried, Tested and Proven - 300 m3 Flotation Cells in Operation

Sep 13, 2010

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

If the industry keeps doing what it has always done, it will continue to get what it has always got - rising operating costs. Why is this so? Generally grades being chased are becoming lower, stripping ratios becoming higher, ability to attract personnel to the industry becoming harder and/or more expensive, higher safety standards are being demanded and environmental governance is being enforced.   How then should the surface mining industry plan for the future whilst delivering on improved safety and the environment? In-pit crushing and conveying (IPCC) points the way, as a partial or complete substitute for trucks.   IPCC systems promise significant advantages over traditional truck and shovel operations, including improved safety, reduced operating costs, reduced dust and noise emissions, far greater efficiency in energy use (electric versus diesel motors predominantly and the ability to regenerate electricity back into the local grid for downhill situations), reduced carbon emissions (dependent on power generation source) and reduced water consumption. Despite these advantages, there is a general industry reluctance to migrate from truck and shovel operations. This reluctance stems from a familiarity with truck and shovel operations and a perceived concern that IPCC lacks flexibility which will negatively impact on the mining operation.   In studies conducted since 2007 (with the new modular builds) comparing IPCC with truck-optimised pit designs, IPCC has delivered up to USD$0.82 per tonne moved less than an equivalent truck operation. In addition, IPCC is easily automated from a central control room (local or remote) - something that trucks have yet to commercially achieve.   IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations - its safety, the impact on the environment and its costs. It maybe of interest to note that there is over 200 IPCC installations worldwide today.   This paper and presentation will assist in furthering the understanding of IPCC and its applicability.

Jun 1, 2010

The emergence of China as a global economic power has not been without its birth pangs and the current coal market is testimony to this. Traditionally the coal market has been controlled by mature economies that functioned along balanced lines of supply and demand. The emergence of China and India as major forces in the international market has shifted this balance of power from mature economies to the developing economies of China and India. Of late Chinese Central Government policy has caused wide swings in the supply of Chinese coking coal and thermal coal to the international Asian markets. This has resulted in huge increases in demand for coal from producers in Australia, Canada, Indonesia, USA and Russia. Additionally since the late 1990s the liberalised Chinese economy has been growing by between nine to 12 per cent per annum. The corresponding rise in the standard of living of their 1.4 billion people has resulted in a strong demand for raw materials, initially met by domestic production and more recently met by the importation of raw materials including iron ore, oil, coking coal and thermal coal. Commensurate with this growth in China has been the emergence of India (pop one billion) as another major developing economy in the region. Whilst the Indian standard of living is lower than that of the Chinese, this subcontinent still has some 300 million people with middle class consumption demands. India is a major importer of oil, coking coal and thermal coal. It exports iron ore to China with growth parallel to China (seven to nine per cent per annum). These combined new demands from India and China have put unprecedented pressure on the global supply of coking and thermal coals. These pressures are reflected in the current world spot prices for coking and thermal coals which are at historically high levels. Whilst current demand from China and India is high it is anticipated that new projects will partially satisfy this increasing demand. Expectations are that overall thermal and coking coal prices will rise steadily. This paper seeks to identify the potential effects of Chinese and Indian economic growth on the international markets for coal.

Jan 1, 2004