Search Documents

By C Antonio, R Narayan, A Scheuermann, S Quintero, M Edraki, M Ziemski

Tailings are mostly loose material and can be classed as non-plastic sandy silts. They also tend to have low permeability, resulting in slow consolidation (settling) rates and low shear strength, even after consolidation. These qualities make them prone to liquefaction and, therefore, physical instability. In contrast, coarse waste rocks possess high shear strength and permeability when stacked in dumps. However, air and water flow-through the voids can cause acid mine drainage (AMD) with significant undesirable environmental implications. Combining the two waste streams before disposal by mixing presents a potential opportunity to harness the desirable properties of both waste streams. This practice is termed co-mingling and is prevalent within the coal processing industry. Co-mingling of metalliferous mine tailings is, however, a relatively new concept. By combining the coarse waste rocks and fine-grained tailings streams, the fine tailings tend to fill the voids between the waste rocks, reducing hydraulic conductivity and advective air (oxygen) flow into the rocks, thus possibly reducing acid mine drainage (AMD). Conversely, tailings are introduced to large frictional particles from waste rocks, providing reinforcement, stability, and possibly improved drainage. New separation methods are being introduced to the mining sector, which have the capacity to extract waste with significantly larger particle sizes. High Voltage Pulse (HVP) is a technology in which relatively coarse particles ranging in size from 30 to 100 mm are exposed to an electric pulse discharge. This pulse preferentially fractures mineralised particles while leaving unmineralised rock (gangue) intact. The stream can then be passed via a screen, with smaller mineralised particles reporting to the undersize and removing coarser unbroken barren particles, thereby eliminating waste. Coarse particle flotation (CPF) is another emerging new technology in metalliferous mining that applies flotation separation to coarser particles than conventional flotation. These new technologies produce different tailings (waste) streams with varying physical characteristics and possibly surface chemistries. This research aims to test new tailings mixtures by applying the co-mingling concept to blend the reject streams generated by these two technologies (HVP and CPF) with the tailings produced by conventional flotation. Combining different waste streams before disposal can improve stability and potentially reduce the acid mine drainage (AMD) rate, thus enabling early access to the tailings storage facility for rehabilitation and closure.

Aug 2, 2023

By A Melkumyan, F Ramos

This paper addresses the problem of prediction of grade variables over volumes (block estimation) for an autonomous mine. Resource estimation is usually concerned with the prediction of the quality of material over volumes (blocks in resource models). This problem is tackled by developing Bayesian block estimation with the Gaussian processes (GPs) framework. GPs are commonly used for nonparametric regression and classification and offer an elegant solution to deal with incomplete knowledge and information. A GP is defined by its mean and covariance function. The parameters of the covariance function can be learnt by maximising the marginal likelihood of the data. This offers a way of automating the covariance fitting process, while at the same time allowing for an assessment of how well the covariance function fits the data. Within the GP framework the calculation of the average grade over a volume can be performed using Bayesian quadrature, which treats an integral as a random variable. First, it is demonstrated that the block kriging equations in geostatistics are the same as Bayesian quadrature. Then, it is determined when closed form analytical solutions for the integrals are possible and quadrature approaches for approximations are briefly discussed.

Sep 26, 2011

By V Kainulainen

Sandvik Tamrock Corp has developed an underground rock flow simulation tool OPTIMINEÖ which is a direct simulation tool for matching suitable technology in rock material flow for underground mine layouts and production requirements. The tool gives the possibility of determining intersections, limitations and critical points in the layout and working procedures at an early stage of a new mine/mining area planning process. The tool combines the supplier machine knowledge with operational know-how and mine environment. It can be used for identifying the effect of an individual incident such as the effect of one additional turn in a continuous loading cycle to the daily capacity. This paper discusses the way the OPTIMINEÖ simulation tool operates, the benefits and restrictions, and reviews how it simulates some example cases and how the mines benefit from the tool in maximising the performance and optimising the mobile fleet, scheduling work and fine-tuning the layout.

Jan 1, 2000

By Alder KF

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials. This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products. This paper presents some predictions of the possible growth of nuclear power installations in Australia. These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50% of new generating plant might be nuclear. Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme. - The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel'; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1970

By S Zaffron, O Loffredi

A critical concern of any mining company today is its relationship with the different stakeholder groups impacted by the operational activity û communities, unions, vendors, local partners and competitors, local and federal governments, interest groups and non-government organisations. What ten years ago would have gone unnoticed, now, and even more so in the future, can drastically impact the profitability and even existence of a mining operation. This paper describes the development and delivery of a new paradigm for creating effective external stakeholder relationships. We report on the actual measurable results of an integrated and highly complex initiative led by Lonmin Plc (Lonmin) and Landmark Education Business Development (LEBD) that significantly altered the nature of the relationship with the stakeholders. Given the nature of the long-term investment required in a mining operation, any breakdowns or surprises in its relationship with external stakeholders brings with it the potential for major loss. The transformation of executive and senior management and community leadership was required to enable them to be effective in managing this complex set of circumstances.

Jan 1, 2006

By Qixiang Y

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst,and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas.This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By G Barla

In Europe, a major interest in the infrastructure and tunnelling fields is in the new crossings of Alps in the form of base tunnels, which are important components of the high-speed (for passengers)/high-capacity (for freight) Trans European railway corridors. These tunnels cross the mountain belt at the elevation of the main cities and basins located all around the Alps and are longer (up to 57 km) and deeper (up to 2500 m) than all tunnels constructed in the centuries before. The excavation of the first Alpine railway and road traffi c tunnels could in general be carried out successfully by conventional excavation methods. With the great lengths of the new base tunnels, mechanised excavation by using tunnel boring machines (TBMs) is imperative as it contributes significantly to savings in construction time and costs. Questions are however posed on the adoption of such a systematic tunnel construction method given the severe ground conditions which are some time anticipated along the tunnel alignment, with possible major geological hazards such as water inflow in heterogeneous fractured or karstifi ed rock masses, stress-induced tensile failure of hard rocks, and plastic shear failure and squeezing of weak rocks, etc. This lecture is to briefly review the current state-of-the-art in the understanding and modelling of two such critical hazards as spalling/bursting and squeezing ground behaviour. With the present interest in the design of mechanised tunnelling with TBMs in such conditions, the complex interaction between the rock mass, the tunnel machine and its system components, and the tunnel support is studied in detail by numerical modelling. The research and development efforts presently underway with the intention to provide the designer with a novel three-dimensional (3D) simulator of mechanised tunnel excavation are presented. Case examples are discussed with reference to the Lyon-Turin Base Tunnel design.

Mar 8, 2011

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The Sishen iron-ore-mine produces 3 pro= ducts with size gradings of 25 to 8 mm, 11 to 5 mm and 5 to 0,2 mm and has a product capacity of 20 Mtpa. Ore is produced at an average Fe content of 66,2 % Fe for the two coarser pro= ducts and an average of 65,3 % Fe for the fine ore product. Three stage crushing is practised to re= duce the run-of-mine ore to -90 mm after which it is screened into five different size frac= tions of which four are heavy media beneficiated in static baths and cyclones and the fifth frac= tion discarded to slimes dams. A final three stage crushing and screening process is employed to produce the final three Products which are homogenized by means of blen=ding systems nrinr to despatch.

Jan 1, 1987

By D R. L Vedoy, L Botha, S P. Gumfekar, J B. P Soares

Most of the known in-place reserves of oil sands are found in Canada. These oil sands ores are mined using various processes to extract bitumen. The by-product slurry resulting from the extraction process, known as tailings, is discharged into tailings ponds. Fine kaolin clays are an important ingredient of the tailings because they remain suspended in water for many years. Current polymeric flocculation/dewatering technologies use acrylamide-based polymers such as polyacrylamide (PAM), but sediments produced using PAM-based flocculants hold considerable amounts of water due to the formation of loosely-packed flocs. Anionic polymers are better flocculants due to bridging and the charge-neutralisation mechanism. In this paper, we will compare the synthesis of two flocculants: thermosensitive, anionic flocculants and thermosensitive, hydrophobically modified anionic flocculants. The first flocculant is a copolymer of acrylic acid (AA) and N-isopropyl acrylamide (NIPAM), in which AA is the anionic monomer. The second flocculant is a copolymer of NIPAM, AA and the hydrophobic monomer N-tert-butyl acrylamide. We evaluated the dewatering efficiency of 2 wt per cent kaolin using both flocculants by comparing settling rates at different flocculant dosages, charge neutralisation ability and supernatant clarity. To better understand floc formation, we measured the floc size formed by both flocculants at different flocculant dosages. We propose that the hydrophobic monomer in the terpolymer flocculant helps expel water out of flocs, ultimately decreasing the water content in the sediments.CITATION:Gumfekar, S P, Vedoy, D R L, Botha, L and Soares, J B P, 2015. Thermosensitive, hydrophobically modified anionic flocculants for dewatering kaolin clays, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 45–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

By C Rizos, A Ng

Land surface deformation can be caused by underground mining activities. The maximum subsidence normally occurs directly above the location of the excavation of the coal seam. In the case where the longwall mining technique is applied, the magnitude and shape of the subsidence bowl are constrained by the longwall structure (pillar). This paper describes the use of satellite radar interferometry for monitoring surface subsidence due to underground mining, as a cost-effective geodetic technique and complementary to conventional ground surveying techniques. This paper uses data acquired by the current generation of SAR satellites û the European ENVISAT and the Japanese ALOS û to monitor ground subsidence in the southern highland coalfield in New South Wales, Australia. An accumulated DInSAR subsidence mine map is produced using six successive ALOS acquisitions. The results are post-analysed with the aid of geographic information systems (GIS) and validated using ground survey data.

Jan 1, 2008

By M Stewart, J Petrie, L Basson

This paper explores tools which have the potential to promote and assess the formation of partnerships between the minerals and energy industries to enhance the economic, environmentally responsible and socially acceptable use of energy. There is a need to look at energy provision and energy services in an integrated manner with key drivers for economic development û both locally and regionally. The minerals sector will remain highly significant to regional economic development in a number of globally significant regions in the medium term. Furthermore, mining, minerals and metalsÆ projects are both consumers and, in some cases (potential), generators of large amounts of energy (electricity included). It is therefore appropriate to focus on the promotion of partnerships between energy providers and the minerals sector which seek to improve resource efficiency within the combined minerals/energy envelope, guided by the tenets of Sustainability.Whilst there has been considerable development of systems analysis tools in recent years to address this sort of æcomplex systemsÆ analysis (Life Cycle Management, Cleaner Production and Industrial Ecology arguments for example), there is no effective roadmap available to decision makers to guide the selection and exploitation of these tools in different contexts. Our previous work developed a Decision Support Framework (DSF) which provides some guidance here, but only within the context of coal-based power generation. The DSF employs the tools of Multi Criteria Decision Analysis (MCDA), within which trade-offs between competing objectives are explored in such a way that alternatives can be compared without necessarily reducing all the different cost and benefits to a common basis (eg a monetary basis). Even if the existing DSF is extended to include all aspects of supply-side management, it is still lacking the necessary tools to analyse energy providers as dynamic network partners within minerals projects (or indeed any resource or manufacturing sector). New models are required for this, which firstly, seek to characterise such network structures, and secondly, enable the application of the necessary analytic tools to exploit these partnerships and networks for optimal performance.This paper explores the development of such an integrated set of network analysis tools, and their relation to the DSF. Due consideration is given to the choice of the attributes needed to characterise partnership linkages and network integrity (eg security of supply of electricity), and the efficiency of material transformations within any node of the network (as a function of energy consumption), and the impact that this has on the viability of other linkages (eg due to reduced availability of raw materials). We discuss how these perspectives help shape the form of objectives to be considered by MCDA.

Jan 1, 2004

By C Sennersten, A Hellicar, C Lindley

Traditional methods of resource modelling and mine planning rely upon geostatistical methods applied to exploration drill core data to derive a three dimensional model of the distribution of metal grades, quantised into rectangular prisms or blocks. The resulting block model is a primary input into short, medium and long term mine planning. However, block attributes are averaged or interpolated over a complete block, meaning that information at smaller scales is lost to the mine planning process. Grade engineering for new mining methods, such as the development of more accurately controlled blast designs, continuous miners for hard rock and sensors for rock properties that can be distributed along the operations process and value chain, allows excavation to be much more selective than traditional blasting, and provides data for driving earlier separation of waste from ore. This selectivity can be optimised if the resolution of resource models can match or exceed the spatial resolution of selective mining technologies. Opportunities for selective mining increase as a deposit becomes more heterogeneous. This leads to an interest in methods for estimating the distribution and characteristics of mineral heterogeneity within the ore-body. The objective of this work is to present some definitions of mineral heterogeneity, and to explore how heterogeneity as defined can be measured and inferred within ore-bodies.CITATION: Hellicar, A, Sennersten, C, Lindley, C and Evans, B, 2018. Heterogeneity assessment for grade engineering in complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 11–13 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Although laterite ores already provide a significant proportion of the world's nickel and cobalt production it is anticipated that they will surpass sulphide ores as a source of nickel in the next century. The most recent period of greenfield nickel project construction was during the 1970s when it was notable that all of the eight new plants were based on treating laterite ores. This was because of the relatively large selection of available high grade laterite ore deposits amenable to cheap open cast mining and a paucity of high grade sulphide ore prospect alternatives. Of the three processing options for treating laterite ores: 1. smelting for the lower horizon saprolite ore, 2. ammonia; and 3. acid leach for the upper horizon limonite ore, smelting currently accounts for about 80 per cent of nickel production. In the future, as saprolite ore grades decline because of relatively high exploitation rates, the incentive to process the large untapped reserves of limonite ore will increase. The high cobalt content of limonite ore also makes it ideally suited to processing by a hydrometallurgical rather than smelting route. With only two exceptions, all saprolite smelting operations have a Class 2 nickel end product (largely ferronickel) and do not produce a cobalt by-product. As a result of technological advances, the modified ammonia leach process for limonite and transition ore as undertaken at Yabulu, now allows the production of pure nickel metal as a Class 1 product, along with significant tonnages of cobalt by-product. The mixed Ni-Co sulphide intermediate product of the pressure acid leach processing of limonite ore at Mon is converted to Class 1 nickel and cobalt metal at Fort Saskatchewan, Canada.

Jan 1, 1996

By Kavetsky A

A new model of flotation is presented which allows predictive calculations of total solids flows and metal grades and recoveries to be made for industrial flowsheets. A method of making these calculations is presented and illustrated with examples. The problem of determining sufficient flotability characteristics from a sample of circuit feed to predict the behaviour of that specific ground ore in the flotation circuit (ie performing flotometric analysis) is addressed, and some suggestions are made for its solution. A feature of the flotation model is its practical technological orientation, allowing determination of a small number of ore flotability parameters by fitting observed batch kinetic flotation data. The unit model explicitly includes the cell aeration as total bubble area per unit pulp volume, and pulp residence time. Although more complex unit models are feasible, it is thought that this model is sufficiently realistic to illustrate the points made. The modelling approach is illustrated by application to flotation data from a Kambalda ickel circuit. The model is parameterised and ore flotability parameters are back-calculated from batch kinetic data. These parameters are then used to fit the observed behaviour of the industrial circuit by numerically adjusting the unit aerations. Finally, it is shown how the model may be used to predict the effect of circuit and ore changes on the circuit's technological indices.

Jan 1, 1992

By R Lau

In recently completed road tunnel projects in Queensland, such as the Airport Link and the Clem7 tunnels, there is a smoke duct running along the roof of the carriageways to extract smoke in case of fire. In New South Wales, no road tunnels have a smoke duct. In the Melbourne City Link tunnels, there is a small smoke duct running along the roof. All of the tunnels are safe as claimed by the designers and authorities. However, there is significant cost associated with providing a full size smoke duct compared with no smoke duct. This paper is going to present a comparison of the road tunnel safety with a smoke duct and those without one from a risk perspective. It further discusses the cost-effectiveness of such provisions and whether similar levels of safety could be achieved without a smoke duct.CITATION:Lau, R, 2014. Smoke duct or no smoke duct for road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T Baumgartl, A Costine, B Boshrouyeh, M Edraki

In mineral processing, the management of tailings may become increasingly more challenging with a change of ore type and the quality of water used in the plant. This, in turn, may affect the overall costs of the operation and water usage and, in the long-term, pose challenges for mine closure and rehabilitation. Depending on the applied treatment technique, the short and long-term properties of tailings are largely determined by the fine particles. Most clay materials and ultrafine particles exist in tailings from oil sands, coalmines and base metals, bringing about challenges in dewatering performance. Moreover, given the growing concern for water scarcity, the minerals industry is increasingly turning towards the use of saline water, which poses yet another challenge for tailings management. The high salt content alters the behaviour of clay particles, making dewatering a more complex process than in freshwater systems (Boshrouyeh Ghandashtani et al, 2022; Costine et al, 2018). High-density techniques for tailings management have been used for several years in the mineral industry. In this regard, one of the novel and promising dewatering methods is in-pipe or inline flocculation, where the polymer is added at high dosages to thickener underflows, giving additional (likely denser) aggregation, releasing more water on deposition compared to low solids thickening. Previous research in the field of flocculation has primarily focused on the process of flocculation itself, specifically the settling rate and size of aggregates, rather than the long-term impacts of the produced tailings materials (Liu et al, 2020; Jeldres et al, 2017). This is particularly true for the novel method of this technology, where polymer is added to the thickener underflow. Furthermore, these studies have used small-scale set-ups using buckets/beakers, plungers and mechanical stirrers for the flocculation process. Unfortunately, these methods lack the necessary control over the properties of the treated tailings, which can lead to irreproducible mixing and dispersion of viscous polymer solutions (Fawell, Costine and Grabsch, 2015). Consequently, a system that can work with a wide range of operational conditions for high-solid tailings material is essential for reliable and reproducible results. The objectives of this study were to determine the effect of different type of polymers in the presence of monovalent and divalent salts on the inline flocculation of artificial tailings. The next step was to evaluate the impact of high-dosage polymer addition on geotechnical properties such as settling rate, consolidated density, rate of consolidation and the hydraulic conductivity of tailings. In addition, this research aimed to fill a knowledge gap and investigate the feasibility of using polymer-treated tailing in removing the copper ions and then quantify the performance of produced aggregates under time-dependent processes.

Aug 2, 2023