Search Documents

Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. Since 1980, Australia's share of the world's output of these minerals has fallen. Exhaustion of known resources, together with the changing composition of new deposits, is expected to result in Australia's share of the rutile and zircon output continuing to decline. Its role as a major supplier of upgraded ilmenite, that is synthetic rutile, is expected to increase. In 1994, the Bureau of Resource Sciences assessed Australia's demonstrated resources of mineral sands as follows: rutile 14.4 Mt, ilmenite 132.5 Mt, and zircon 21.0 Mt. These resources are located along the coast of Queensland and New South Wales, in the Murray Basin of New South Wales and Victoria, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth. However, some 45 per cent of rutile and zircon resources along the coast of Queensland and New South Wales are not available for mining because of environmental concerns. World demonstrated resources are estimated at 40 Mt (contained TiO2) for rutile, 50 Mt for zircon and approximately 312 Mt (contained T1O2) for ilmenite. Outside of Australia, the most important resources of rutile, ilmenite and zircon are in South Africa (rutile, zircon , and ilmenite in the form of titania slag), Sierra Leone (rutile), India (ilmenite, zircon and rutile), and Canada (hard rock ilmenite). Significant resources of ilmenite occur in Madagascar and Mozambique.

Jan 1, 1996

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

By Amer S, Novais A. Q, Limpo Gil J

A proprietary hydrometallurgical ammonium chloride process for the recovery of not only zinc, but also copper, lead and silver from sulphidic zinc-rich concentrates has been developed at bench scale by CENIM and INETI (ex-LNET) as part of a research project supported by the Commission of the European Community (DGXII). This paper deals with the innovative chemical aspects applied to this chloride process and also with the more relevant data relating to mass balance, heat balance and process economics. Under mild temperature and oxygen pressure leaching conditions it is possible to extract practically all the zinc together with the other metals of interest and to precipitate simultaneously the solubilised iron fraction as goethite. The pH is kept close to neutrality in spite of the ammonia released in the leaching of the non-ferrous sulphides. A buffer effect is observed mostly due to the formation of zinc ammines which are very soluble in this medium. The zinc is further extracted by D2EHPA, the acidity being neutralised by the ammonia. Most of the ammonium chloride is naturally regenerated in this step. The zinc is recovered as zinc cathodes in a conventional sulphate electrowinning circuit. All the main raw material consumptions excluding the concentrate, such as oxygen, lime and ammonium chloride are linked to the sulphate formation in the leaching step which must be kept as low as possible by decreasing the reaction time under neutral conditions. The process analysis is complemented by the economic evaluation of a reference case. Difficulties encountered in finding a more convenient method of assessing the economics of the process in the absence of a reference price for a complex sulphide concentrate are examined and discussed. The reason why this analysis was performed with a much more optimistic metal prices scenario is also highlighted. The process economics are primarily dependent on the zinc market quotations and of course on the concentrate cost. Around 70 per cent of the total revenue is due to zinc sales. Assuming an internal rate of return of 17 per cent, the price of the concentrate can be as high as 255 $US/t for a plant capacity of 320 000 t/y (90 000 t/y of zinc).

Jan 1, 1993

By A Grace, C Sennersten, A Davie, R Lyu, C A. Lindley, O Goldstein, T Thomas, L De Macedo Camargo

Block modelling is a well-established method for modelling ore reserves as a basis for strategic mine planning and mine development. Off-Earth mining, particularly of asteroids, can benefit from block models; however, the significantly different characteristics of asteroids and their methods of mining require reconsideration of the geometry and annotations of block models. Terrestrial block models consist of rectangular prisms within Euclidean coordinate systems. Their labels and parameters typically include location within a mine-specific coordinate system, x, y and z dimensions, specific gravity, hardness, grades of metals of interest and so on.These data provide an input to mine design and strategic mine planning. Mining asteroids may require different coordinate systems (eg spherical, elliptical or cylindrical, rather that Euclidean) and attributes that vary from Earth-based block models. These include: variable gravitational vectors throughout the block modelrotational moment or accelerationrotation rates. Materials within asteroids may show different isotopic compositions. Asteroid mining has the unique characteristic of a mine being identical with an asteroid. The position of the asteroid/mine in space and its full orbital elements provide critical inputs to mission design and costing. Hence, the block model concept needs to be extended with this metadata. The orbital position and behaviour of the Earth must be included for active mine planning, and increasing automation of mine planning and operations needs to consider terrestrial weather and telecommunications infrastructure. Financial planning requires analysis of the net present value of extraterrestrial mining compared with terrestrial alternatives, so a fully automated mining enterprise should integrate terrestrial and extraterrestrial block models at different scales and resolutions. Blocks can be indexed via octrees, allowing for hierarchical scales that support analytics for deriving new knowledge and correlating features across different scales.CITATION:Lindley, C A, Sennersten, C, Davie, A, Goldstein, O, Lyu, R, Grace, A, Evans, B, Pentecost, D, Thomas, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. A multilayer 3D index tool for recursive block models supporting terrestrial and extraterrestrial mine planning, in Proceedings Third International Future Mining Conference, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Drury SA, Williams RD, Nind DC

The Airborne Thematic Mapper is an eleven channel digital scanner which acquires image data in the visible, near infra-red, short wave infra-red and thermal infra-red wave- lengths. A description of the system is presented which includes details of the operating wavelengths and performance parameters of the scanner. Consideration is also given to the aircraft installation requirements. During January 1984 the scanner surveyed the mineral rich areas of Leonora, Laverton and Kalgoorlie in Western Australia. This is a region of intense exploration activity for gold and base metals. Some 30,000 square kilometres were systematically surveyed in a period of ten days. This scanner was flown at 7,000 metres altitude giving a ground pixel size of 17.5 by 17.5 metres. The flight line spacing was 8 kilometres. The overall project took some thirty days from conception to completion. The planning and execution of this operation are described in detail. The resulting magnetic tapes provided 11 channels of digital image data over a 30,000 square kilometre area and a variety of image processing techniques were employed in order to capitalise fully on the results. The imagery provides a powerful tool for the geological mapping of the terrain. The data can also be used to monitor the environmental effects of mining operations.

Jan 1, 1986

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

By T Amiconi

Ernest Henry Mining commenced operations on its copper-gold project in August 1997, some two months ahead of schedule and ten per cent ($35 million) under budget. The mine is located in the highly prospective Mount Isa/Cloncurry mineral district in north-west Queensland, approximately 38 km north-east of Cloncurry. The developer and operator of the project is Ernest Henry Mining Pty Ltd (EHM), an incorporated joint venture between MIM Holdings Limited (51 per cent) and Savage Resources Limited (49 per cent). The deposit is located approximately 40 km north of Cloncurry in North West Queensland and lies beneath a featureless black soil plain with no significant creeks or gullies cutting across the site. Vegetation is sparse and consists essentially of Mitchell grass with occasional low shrubs and trees. Up to nine million tonnes of ore and over 43 million tonnes of waste will be extracted each year from an open pit operation to produce approximately 350 000 tonnes of concentrate when in full production.

Jan 1, 1998

By N Madani, Y Abildin, E Topal

Mine planning is a crucial part of all mining industry projects, and nowadays, geometallurgical mapping through advanced computer technologies provides an opportunity to involve metallurgical responses of a deposit into 3D block model in order to optimise mine planning activities, especially for production forecasting. Including these metallurgical parameters apart from traditional geology and grade-based attributes into resource modelling leads to an extensive approximation for the economic maximisation of mine production due to better forecasting, planning and increasing certainty and the reliability of the resource model (Macfarlane and Williams, 2014). Commonly, geostatistical techniques and algorithms are used to produce models with the high resolution (Brissette et al. 2014; Deutsch et al. 2014; Tolosana-Delgado et al. 2015). The accuracy of the modelling procedure deeply depends on a reliable block model, produced by spatial analysis of corresponding variables that define the geological, metallurgical, mineralogical and chemical behaviour of the deposit. However, there are special cases, where the application of enhanced geostatistical methods is required, to solve the occurred difficulties between variables with multivariate complexities. For example, in oxide copper deposits, the soluble copper grade is a percentage of total copper grade and recoverable by heap leaching processes (Emery, 2012; Hosseini and Asghari, 2015). Hence, the joint spatial modelling of these variables has two difficulties.CITATION:Abildin, Y, Madani, N and Topal, E, 2018. Forecast the mineral processing destinations based on spatial interpolation of geometallurgical variables, in Proceedings Complex Orebodies Conference 2018, pp 2–5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K L. Avarmaa, M A. Rhamdhani, A D. P Putera, H T. B M Petrus, G A. Brooks

Multistage slag treatment was carried out to investigate boron removal from metallurgical grade silicon. Boron is known to be one of the most difficult elements to remove from silicon. Depending on boron initial concentration, boron can be removed from silicon into certain level; most previous studies have attained final 50–100 ppmw (parts per million weight) boron in the silicon using slag treatment. The term ‘multistage’ refers to a process where the resulting silicon from the initial slag treatment is further refined multiple times using a new slag. In this study, an initial slag composition of 45CaO-45SiO2-10Al2O3 (wt per cent) was utilised. Using this technique, boron level in the silicon was expected to be gradually lowered because the new slag will always have more capacity to reach the equilibrium distribution coefficient (LB = (ppmwB)slag/(ppmwB)Si). The current study was carried out through combined thermodynamic calculations (using FactSage™ ver 8.2, by Thermfact Ltd, thermochemical package) and high-temperature experimentation. The thermodynamic calculations were carried out for reactions at 1500, 1550, and 1600°C for three different scenarios: 1. Single stage refining with varied slag to Si ratio. 2. Multistage refining with slag to Si ratio of 1:1. 3. Multistage refining with slag to Si ratio of 2:1. The multistage experimental work was carried out at 1550°C under inert gas atmosphere each time for 2 hrs, with slag to Si ratio of 2:1. The simulation results indicate that the boron distribution coefficient stay essentially constant with varying slag to Si ratio and temperature, around 1.8 to 2, and the experimental results measured LB in the same range, between 1.5 and 2.5. By harnessing this feature, the simulation showed that boron can be removed by approximately 78 per cent in each stage. The experimental result confirmed that the boron concentration in the silicon was reduced by a total of 97.8 per cent from its initial value using four stages of slag treatment, from initial 270 ppmw down to 6 ppmw.

Aug 21, 2024

Olympic Dam Operation is located in the Stuart Shelf Geological Province approximately 520 km north-north-west of Adelaide in South Australia. It is estimated to be one of the worldÆs top five copper orebodies by size and the biggest single occurrence of uranium. The deposit was discovered by Western Mining Corporation in 1975. Exploration was based on a conceptual model for the formation of sediment hosted copper deposits together with gravity and magnetic anomalies.The capital cost of the current expansion is estimated to be A$ 1.64 billion. The underground expansion includes a total of 36 km of lateral development, a railway haulage system delivering ore from a series of ore passes to a new crusher station and a significant increase in ventilation capacity and mine services.In the current underground expansion the mining method will essentially remain unchanged. The ore handling system will incorporate some recent advances in technology, improving efficiency and safety standards.Major infrastructure excavations are designed by a team of engineers attached to the Olympic Dam Expansion Project and a number of consulting groups. Once the expansion is fully completed it is expected to increase the current annual underground production level from 3.4 Mt to 9.0 Mt of ore by the year 2000. Mine design engineers working for the Olympic Dam Operation have recently completed a three year final design plan to achieve this target.Access to the existing mine is through the decline and Whenan shaft. The Whenan shaft was originally sunk as an exploration access and later upgraded for hoisting. The 4 km long service decline connecting to the Whenan shaft was later constructed to accommodate the increase in service demand. The Robinson and Sir Lindsay Clark shafts were developed at later stages to cater for the hoisting during and following the expansion lead up.

Jan 1, 1999

By A J. Minns

This paper addresses the question: how can the minerals industry remain viable; viable in the sense that we are able to access land for exploration and discovery, we are able to develop and operate mines (and processing plants) safely and profitably and we are able to close operations in a responsible manner, so that modified landscapes are restored to acceptable community standards?Many of the answers to this question can be addressed through the theme of this conference û that of eco-efficiency. The eco-efficiency concept is very useful, since it does help to translate principles of sustainability into business value at the operational level. To provide some context to how this can be achieved, the paper discusses what is happening at the international level, outlines some key industry initiatives within Australia and then discusses what work is being done within companies.

Jan 1, 2004

By M Clay, J Dunlop

Thermal and metallurgical coal mining in Queensland has resulted in mines which contain voids due to open cut mining. While there are several proposals for greenfield coalmines or expansions to existing operations, many existing open cut coalmines are reaching maturity and most will leave one or more residual voids in place. The rehabilitation of mine voids is challenging. Water held in voids will evaporate over time leaving solutes to concentrate. This is likely to lead to poor water quality with limited practical use. The most basic practices to rehabilitate voids have historically involved stabilising the high and low walls, bunding to provide flood protection, and preventing public access. Regulatory reforms for mine rehabilitation were introduced in Queensland as part of the Mineral and Energy Resources (Financial Provisioning) Act 2018, and aimed to strengthen progressive rehabilitation planning, limit risks to the environment and improve outcomes for local and regional communities. Under the reforms, the goal for rehabilitation of voids is to achieve a safe, stable, and non-polluting landform, which can sustain a post-mining land use (PMLU). The reforms also introduced a requirement to describe rehabilitation of mined land in Progressive Rehabilitation and Closure (PRC) plans, replacing the description of such plans in Environmental Authorities (EAs). The reforms are not retrospective and recognise historic approvals for voids, meaning established voids will remain in the landscape as non-use management areas (NUMAs). The objectives of this study were to outline historic void rehabilitation planning practices, describe water quality limitations of Queensland mine voids and identify possible opportunities for improved planning

Aug 2, 2023

The Kunwarara magnesite deposit is the largest known magnesite (MgCO3) deposit in Australia. It is located under black soil plains to the north of Rockhampton in Queensland. The deposit consists of magnesite nodules set in a fine-grained sandstone, siltstone and mudstone matrix. The magnesite is derived from weathering of serpentinite in adjacent hills and transport of magnesium in solution to a Tertiary/Quaternary river system. The magnesium has come out of solution in the active river system, and combined with atmospheric and biogenic CO2 to form magnesite nodules. The magnesite can be very pure with certain varieties up to 98 per cent MgO (LOI free). The deposit has been mined since 1991 and processed into magnesia (MgO) which is sold into refractory, agricultural and other markets. The geologist is an integral part of the small mine technical team. The role of the geologist includes characterisation of the ore through drilling and bulk sampling, supervision of geological aspects of mining and assistance in the optimisation of ore processing.

Jan 1, 2000

The ores described in this paper are from the two principal orebodies at Wiseman's Creek, a small village about 22 miles south-east of Bathurst in central-western New South Wales.The first official reference to mining at Wiseman's Creek is in "Mineral Statistics of New South Wales" of 1875, which reported that the Wiseman's Creek Copper Mining Company had proved a lode-later known as "North Wiseman's"-to a depth of 120 ft., where it was found to be 20 ft. wide. By 1876 the erection of a mill and smelting works had commenced, and the sulphide ore found to contain copper lead, zinc, silver and gold. Some oxidised ore was also being worked. Operations were, however, generally unsuccessful, and sporadic work up until 1907 produced only about 5,000 tons of ore. The other more important orebody of the locality-the Phoenix-was not opened until about 1895. By 1908, as reported by J. E. Carne, the shaft had been sunk 340 ft., with the extraction of both oxidised and primary ore. At the time of the slump in copper, pric'es in 1907 approximately 3,000 tons of, ore had been produced.Several smaller orebodies were discovered and worked during the same period as the North Wiseman's and Phoenix, but their output was more or less insignficant. THE OREBODIES AND THEIR GEOLOGICAL SETTINGIt is now impossible to examine the orebodies underground, but they appear to have formed a series of flat lenses, whose major axes were parallel to ,the foliation of the enclosing quartz-chlorite-muscovite schists. The largest ,of these lenses was worked as the North Wiseman's orebody, which was reported by Carne to vary in width from 1 ft. to 20 ft., and which probably extended discontinuously over a strike length of about 1,000 ft. The Phoenix orebody is stated to have varied from 1 ft. 6 in. to 3 ft. in width...

Jan 1, 1955

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:  TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By H Hy÷tyniemi

In this paper multivariate data analysis performed on a new multi-camera system implemented to zinc flotation circuit of PyhSsalmi mine is presented. Image-analysis-based system was developed to take advantage of the commonly known fact that the changes in the flotation process are reflected to the visual appearance of the froth surface. Most often the changes are seen first in the froth and later in other process measurements. The image variables are already utilised in closed loop control and considerable savings are achieved with the current setting, but the results coming from the separate cells are used individually. This is clearly not the optimal way to take advantage of the many measurements coming from different locations of the process. A better approach would be for example to use the measurements coming from the early stages of the process to predict the behaviour (or improve the quality of measurements) in the later stages. The methods described in this paper are aimed to improving the situation in this sense.

Jan 1, 2005