Search Documents

By Cox LT

A short term tyre study of trucks operating in a multiple pit surface coal mine showed significant potential for cost savings. The tyre study, conducted on-site over a three months period covered a mixed fleet of 18 trucks ranging from 27 tonne to 77 tonne capacity operating on overburden removal, coal haulage and watering duties. Some existing plant history records and a variety of tyre related measurements during the course of the study allowed the current state of tyre operations to be quantified. Specific attention was given to determining ger>ral trends from historical records and conducting detailed studies of individual lug damage, pressure monitoring and rectification, as well as tyre maintenance procedures. Important haul road parameters including camber, gradient, curve radii and superelevation, constructional materials and surface clean-up were appraised for their influence on tyre wear. Recommendations for achieving long term cost effective tyre utilisation included increased tyre maintenance, personnel development, compliance with haul road design parameters and more stringent clean-up Procedures.

Jan 1, 1982

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

In current mining practices it is desirable to bring about a substantial increase in both rate of face advance and productivity, thus compelling the mine engineer to consider better and more productive ways of mining. Transportation plays a vital role in achieving improved productivity. This paper focuses on horizontal transportation systems. Horizontal transportation is defined from the shaft station area to the end of the stope cross-cut. Traditionally, horizontal transportation is inefficient in comparison to vertical transportation efficiencies and accounts for a high proportion of South African mine accidents. Thus, the role of horizontal transportation has been investigated in detail, as it offers the greatest chance for improvement. The purpose of the paper is to provide a best practice guideline for the design of horizontal underground transport systems. It is intended that the document be used by mine designers and planners as an aide memoir during the design process and benefit may well be gained from retrofit and reorganisation activity. The paper looks at transport systems suitable for deep level gold mining in South Africa and evaluates such items as management, scheduling, and haulage systems. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2003

In 1997, the Australian coal industry through Standards Australia committee MN-001 Coal and Coke recognised the need to produce a Standard giving some instruction on how to inspect and audit mechanical sampling systems. A Guide was developed by sampling subcommittee MN-001-04 and in 1999 the Standard was released as AS4264.5 æGuide to the Inspection of mechanical sampling systemsÆ Coal and Coke. Since that time the author has assisted with other committees in developing the Guide for other commodities such as concentrates and a generic standard for particulate materials. (AS4433.6 released 2000). The Coal and Coke guide is also currently a work item for ISO Standards. This paper is focused primarily on auditing and inspection procedures for coal mechanical sampling systems. It highlights the need for at least a three level inspection protocol where the operators manning the system maintain operational checks, the operators are regularly supervised by the company managing the system and once per year an independent auditor inspects the whole system to ensure compliance with design and standards. It does not cover short- and long-term maintenance of individual systems. With companies already certified to the ISO9000 series, this guide forms the framework to bring the operation and inspection of their mechanical sampling systems into line with these principles.

Jan 1, 2005

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

In open cut gold mining at Mt Magnet and Reedy, grade control sampling is done with inclined RC drilling using one metre samples. In the small open cuts at Rothsay blasthole sampling was successfully used. Underground sampling for gold and copper grades at Rothsay is done using chip sampling. At the Youanmi open pits both Ditchwitch Earthsawing and RC drilling are used.All assay data are interpreted on sections and plans using a customised SURPAC system. Reconciliations of the grade control predictions of tonnes and grade against initial ore reserves, mining production and milling results are carried out monthly.

Jan 1, 1990

BHP Billiton Mitsubishi Alliance, or BMA, is AustraliaÆs largest coal miner and exporter, and is currently responsible for around a quarter of AustraliaÆs total annual coal exports. BMA and its predecessors have been part of the Queensland mining scene for around 40 years, developing world-class mines, a port, overseas markets, and an international reputation for quality and reliability. From its production base in QueenslandÆs Bowen Basin, BMA produces a broad suite of coals which are supplied to 73 customers in 24 countries. BMA was formed in June 2001 as a partnership between BHP Billiton and Mitsubishi Development Pty Ltd, under which the two companies share equal ownership and management of eight Central Queensland coal mines û Goonyella Riverside, Broadmeadow, Peak Downs, Saraji, Norwich Park, Gregory, Crinum and Blackwater û and the Hay Point coal export terminal near Mackay. This case study focuses on Peak Downs Mine, which was the second largest open cut mining operation to be developed in the northern Bowen Basin for the original CQCA Joint Venture. The first coal was mined in April 1972 and today, Peak Downs has a production capacity of over nine million tonnes of coking coal per annum. The mine is located 30 km south of Moranbah and 195 km south west of the Hay Point port facilities. Coal is mined by open cut mining methods using six draglines and two truck/shovel stripping fleets for overburden removal. Coal seams are mined using excavators and front-end loaders and 210 tonne capacity coal haulers.

Jan 1, 2007

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

The reality is that in today's world almost half of nearly six billion people on the planet do not have access to commercial energy and the services it brings. Based on UN projections, in 30 years time there are likely to be nearly three billion more people in the world, over 90 per cent of them in countries which are already economically poor. The World Energy Council (WEC), through its 102 member countries, monitors trends and developments and projects future trends. WEC is a non-governmental international body representing all forms of energy and is committed to the sustainable use of energy for all mankind. This paper is based on WEC studies and papers presented at its many conferences and congresses worldwide. Primary energy demand growth is dominated by the developing countries over the next 30 years. The world energy mix is projected to change very little over the next 30 years. Fossil fuel supplies (ie coal, oil and gas) are likely to decline from 77 per cent to 73 per cent, nuclear energy may grow from five per cent to six per cent and renewable energy sources (eg hydro, solar, geothermal, wind, tidal and biomass) could increase from 18 per cent to 21 per cent. World energy consumption is expected to grow by over 50 per cent over the next 30 years. The paper reviews changes in energy demand in the world, particularly in the Asia/Pacific region. Environmental issues are covered, as are developments such as solar energy from space and the status of renewable energy forms. Agendas for action to achieve change are also reviewed.

Jan 1, 1997

The brown coal resources of the Latrobe Valley, which include over thirty thousand million tons of coal suitable for open cutting, provide the main source of fuel for the power generation for the State of Victoria. They also provide the basis for the development of a supply of cheap hard fuel for industrial and domestic use, and for the development of the Lurgi process for manufacture of town gas for most of the State. The production of hard char for metallurgical processes and liquid hydro carbons will each, no doubt, play its part in the industrial growth that will be based on these resources.The State Electricity Commission of Victoria, which has been allocated the task of developing these deposits since the early 1920's, is faced with problems of economic selection of deposits for development, and excavation and transport of huge tonnages of coal and overburden-in this year, 19'59, about 12,000',000 tons of brown coal will be won, and over 7,000,000' cu. yd. of overburden will be removed in the four open cuts operated by the Commission; by 1967, eight years from now, the demand will have doubled.This paper deals with the nature and importance of various factors effecting the planning of the development of these resources. It is in essence an introduction to the papers by C. S. Gloe, H. C. G. Rodgers and J. M. Alexander, also being -presented at the Institute conference in Victoria in August, 1959.INTRODUCTIONIt is the intention in this paper to define the factors that come under consideration in the planning and development of the brown coal fields in the Latrobe Valley, whose exploitation by the State Electricity Commission of Victoria was initiated almost 40 years ago. It is proposed to enumerate, and in sorile cases evaluate, the physical and economic criteria that play their part in determining planning for the future.

Jan 1, 1960

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

A continuing demand for exploration geologists, at a level well below that during the mineral "boom" of 1967-1971, will be highly selective. The exploration geologist must be more than the traditional geologist whose primary function has been detailed description of rocks and their recording on a geological map. He must be capable of 1. reconnaissance recognition of favour= able environments for ore mineral concentrations, 2. application and interpretation of techniques of search and evaluation, and 3. evaluation of economic, technological and political interactions that combine to make an ore deposit. Universities have an obligation to their students to provide them with a saleable skill, to educate them so that they can cope profess- ionally and socially, and to provide a mechan- ism by which education can be a continuing process. Humanistic and social studies, develop ment of communication skills, understanding of economic and management principles, ability to assess rock properties that influence extract- ion and beneficiation, and a knowledge of technological developments and limitations are necessary parts of the exploration geologist's

Jan 1, 1974

Infrastructure is defined as all those parts of a mining development which are not directly concerned with mining and mineral processing. Infrastructure is of significant and growing importance in the overall develop- ment of mines, and the costs could be critical in determining the viability of a project. Prior to_project authorisation, feasibility studies are required, often in considerable detail, to determine costs with adequate reliability. It is necessary that the Engineer should be adequately briefed for carrying out these studies and that good liaison and communication with the Owner be maintained. Methods, costs, order of accuracy, and some special requirements of these studies are discussed. After project authorisation, rapid im- plementation of the proposals is generally desired. A suggested organisation and method for this implementation is presented and dis- cussed. Comments on fees, and particular points in the relationship between Owner and Consulting Engineer are given. Particular reference is made to differences in conditions compared with public works projects. Realistic attitudes of mind towards environmental matters, industrial relations, and contractual relationships are advocated.

Jan 1, 1974

By Freeman N

A microcomputer based control system has been developed and implemented at ZC Mines (now Pasminco Mining). The control system maximises throughput at a product size set point while maintaining a "safe" cyclone underflow and mill operating pulp density.To characterise mill and cyclone operation over a range of ore types, 60 circuit surveys were carried out by ZC Mines personnel over a period of four months. The data for each test were model fitted to check for data consistency and to accurately estimate circulating loads.The model fitted results were combined with instrument readings (including in-stream analysis probe assays) and the data checked for ability to predict key variables such as product size and underflow density from measurable inputs.In the resulting control scheme, panicle size and underflow density are not monitored directly, but are predicted by regression equation models based on directly measured variables. The tonnage control loop uses a dynamic model to maximise responsiveness.The system provides a data log output to an mM compatible personal computer at programmable intervals. Comparative data logging over a period demonstrates substantially smoothed circuit performance.The grinding control system was originally implemented using Fischer and Porter micro-DCI controllers. The program has also been implemented on a distributed control system using a sequence oriented programming language.

Jan 1, 1990

DURING the four years, 1922, 1923, 1924, and 1925, China produced the following quantities of non-ferrous metals and ores: Antimony Products - 67,869 (long) tons. The production for 1925 was 20,869 tons, of which 80% was regulus, 14% crude,and 6% oxide.Arsenic (White) - 4200 tons. The production for 1925 was 1200 tons, but only 90 tons were exported, some 25% of which to Hong-Kong, France, and U.S.A. each, and the rest in small lots to other countries. Domestic consumption was 1110 tons, and thelocal price for "cake" was around £47 per ton on 1925 exchange.Arsenic Ore (Realgar) - 1400 tons.Lead Ore (Galena) - 44,853 tons. The production for 1925 was 10,853 tons, of which 16%, produced in Korea, went to Japan, and 84% produced in Hunan, went to Europe.Manganese Ore (Pyrolusite) - 142,567 tons. The production for 1925 was 42,567 tons, of which 94.3% went to Japan.Tin Ingot - 33,480 tons. In 1925 the exports to Hong-Kong were 8880 tons of usual rough tin of 94% to 96%. Most of this was refined to No. I Chinese quality of 99.3% and exported to U.S.A. and Europe, owing to the good price ruling.Sulphur - 12,000 tons. Sulphur is included in this list in order to explain how its production led to the discovery of some other ores.Wolfram - 19,668 tons. The production in 1925 was 5868 tons, most of which came from the Quee Mee mountain district in South Kiangsi, from the detrital deposits. Civil disturbances prevented the usual output from Hunan border.Zinc Ore (Blende) - 134,190 tons. Exports for 1925 were 34,190 tons of low-grade ore, averaging 30% zinc, 14% lead, and 7% silver...

Jan 1, 1927

In response to requests from the iron ore mining industry, the Commonwealth Scientific and Industrial Research Organisation (CSIRO) Division of Mineral Physics has developed a number of bulk analysis techniques in which analyses are obtained directly from ore samples weighing many kilograms or from ore located on conveyor belts.Because penetrating neutron and gamma radiation is used, measurements are obtained from a large volume of ore, which ensures thal the analyses are represelllative of the bulk.Two different gamma-ray techniques have been developed to measure iron ore grade. The first is based on backscallering of 60CO gamma rays, while the second involves measurement of the annihilation radiation which arises when the ore is irradiated wilh 226Ra gamma rays. Both techniques measure the iron concentration with an accuracy (1 s) of better than 0.4% Fe.A thermal-neutron irradiation technique using a 252Cf neutron source has been developed for the simultaneous determination of iron and the aluminium impurity (expressed as AI2O3) in iron ore fines on a conveyor bell. Because the conveyor speed must not exceed about 0.05 m/s, if good accuracy for AI2O3 is required, an auxiliary analysis bell is required Lo avoid inLerference with normal ore processing. Dynamic trials have demonstrated that accuracies of 0.6% Fe and 0.1% AI2O3 can be obtained.

Jan 1, 1985

By He F, Zhu D

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced Normally.

Jan 1, 1992

By Johnson N. W, Quast K. B

Over the years there have been occasional references in the literature to the activating effect of cyanide in galena flotation with xanthates. These have usually been associated with the processing of lead-zinc or copper-lead-zinc ores. Bubble contact curves for the pure galena-xanthate system show a flotation edge at pH 10.4 independent of sodium cyanide concentration which was thought due to hydroxyl ion, not cyanide ion.Flotation tests were conducted on samples of Mount Isa lead-zinc ore using varying concentrations of sodium ethyl xanthate and sodium cyanide. At low collector concentrations, galena recovery kinetics improved with sodium cyanide addition, and the higher the cyanide concentration, the higher the galena recovery rate. At higher collector concentrations, galena recovery rate was independent of sodium cyanide addition.For a given collector addition, the lead grade-recovery curve shifted to an improved position with increasing sodium cyanide level. For the same recovery there was an increase in the lead grade with increased sodium cyanide addition, and this increase was most dramatic at high sodium cyanide concentrations.The presence of sodium cyanide during the grinding of Mount Isa ore caused surface passivation of the iron sulphides and possibly the sphalerite.These sulphides, therefore, reacted with less of the oxygen present in the pulp, hence more oxygen was directed to the surface of the galena. This resulted in an enhancement in the total amount of xanthate adsorbed on the galena that is reflected in the improved flotation response of that mineral.

Jan 1, 1990

By Chander S

Properties of surface films on chalcopyrite and pyrite differ due to variations in the mechanism of oxidation of the two minerals. In the case of chalcopyrite the first step in the oxidation is the release of iron as ferric ions, which hydrolyse depending upon conditions prevalent in solution. The iron oxide/hydroxide layer formed by hydrolysis of ferric ions is quite porous and easily detachable from the surface of chalcopyrite. When the surface oxide layer is detached a sulphur-rich layer is exposed making chalcopyrite hydrophobic. The thickness and properties of the sulphur-rich layer determine its flotation response, both in the absence and presence of collectors. In the case of pyrite, on the other hand, iron is released as ferrous ions which require much higher pHs to hydrolyse. These ions remain adsorbed on the surface of pyrite making the surface hydrophilic. When the iron species are complexed with chelating agents such as ethylene diamine tetra acetic acid, pyrite was hydrophobic. Siderite forms in the presence of carbonate ions, which might be present in several flotation systems. Siderite nucleated on isolated sites at the surface. The presence of such a precipitate is likely to influence the interaction of pyrite with various reagents thereby altering its flotation behavior. To determine the mechanism of oxidation, kinetics of oxidation of chalcopyrite and pyrite was studied using several electrochemical techniques, namely, cyclic voltammetry, polarisation and impedance spectroscopy. Floatability of the minerals was investigated by measurement of contact angles on mineral electrodes and by Halimond tube flotation. Impedance spectroscopy was especially useful for estimating various properties of surface film for both the minerals. Properties such as charge transfer resistance, porosity, and capacitances of the surface films on the two minerals are compared under several conditions of oxidation. These properties were found to be a strong function of the rate and the extent of oxidation.

Jan 1, 1993

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978