Search Documents

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

There is an increasing demand for refrigeration as mines progress deeper. Mine refrigeration plants have special requirements in terms of their duty and application. There are no national or international standards applicable for the testing of these plants. There have been numerous examples of plants failing to meet their required nominal capacity, but with the plant owner being unable to enforce the design duty on the manufacturer, due to a failure to unambiguously specify testing or accepting criteria. This paper discusses some of the reasons for performance shortcomings and describes a methodology for developing and specifying performance criteria, when inviting design and/or construction tenders, and a method of performance and acceptance testing once the plant has been built and commissioned. These guidelines encompass the full range of performance duties expected from a mine plant, including stable operation at maximum and minimum plant capacity, and under the various combinations of extremes of high and low condensing and evaporating pressures. A description of a methodology for developing a computer-based mine refrigeration plant model is also presented as part of the performance testing criteria. The methodology is illustrated with reference to the actual performance and acceptance testing process used on the worldÆs largest bulk air cooler (R67) at the Enterprise mine at Mount Isa, Australia.

Jan 1, 2005

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

Two key elements in the design of a pastefill or high density backfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: Vacuum or pressure filters. These represent the ætraditionalÆ approach to the preparation of pastefill. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producingpaste/high density backfills. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach.This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material. No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mines in Canada.

Jan 1, 1998

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (<1.3) and a high Cu/S ratio (>1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B Olsson, R Norman, M Volz

Australia has seen unprecedented demand for coal exports in the last ten years and this demand is set to expand further still according to many analysts. This rapid increase in demand has placed pressure on multi-user coal chains to guarantee the capability to meet the required demand, in terms of both current operations and capacity expansion.The projects required to deliver these forecast tonnages take place in an increasingly complex commercial and technical environment. These challenges include brownfield and greenfield projects, multiple rail and terminal service providers as well as a myriad of mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing complexity and integration drives the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems and the resultant capacity of the integrated system is the key to maximising value. TSG advocates the use of a total integrated system approach to understand the behaviour and performance of complex coal chains.Recently, TSG has worked in conjunction with the Integrated Logistics Company and a number of stakeholders in the Dalrymple Bay Coal Chain to deliver the first independent system master plan. This master plan has provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. It is underpinned by a highly detailed discrete-event simulation model of the complete coal chain as an integrated system, including mine load-outs, rail, terminal and port operations.This paper provides an overview of the study and describes the differences between subsystem and total integrated system model performance.

Sep 26, 2011

By D P. Murphy, R F. Dewhirst

Traditionally closure has been seen by the Resource sector solely as a green or an environmental issue, focused primarily on the requirement to rehabilitate the site following cessation of production activities. In addition to operational, maintenance and production aspects of processing plant design, future design teams will need to take a more holistic view and consider an increasing number of sustainability issues including safety in design and cleaner production as well as closure itself. Sustainability principles being adopted by industry such as the Minerals Council of AustraliaÆs Enduring Value Framework are now broadening our understanding of closure. While issues around the closure of tailings dams and associated infrastructure have been widely studied, few investigations have looked closely at the implications of closure on the design of minerals processing plants. It is likely that design teams may be able to make a significant contribution to meeting industry objectives by adopting innovative designs which, in addition to meeting production objectives, deliver sustainable and cost effective plant closure outcomes. This presentation explores the opportunity for innovative design of mineral processing plants through the assessment of alternative closure objectives. This assessment specifically looks at current industry standards and statutory requirements, as well as potential risks and opportunities associated with each objective. Alternative design strategies to meet these objectives are discussed.

Jan 1, 2006

By D Craw

The Macraes gold deposit is located in a low angle NE dipping (~15¦) shear zone, the Hyde Macraes Shear Zone (HMSZ) cutting greenschist facies metasediments of the Otago Schist. The shear zone is host to large volumes of mineralised schist and relatively sparse quartz veins. Early in the development of this through going shear the schist experienced an episode of hydro fracturing and fluid redistribution. As a result, presently exposed schists within the Intrashear sequence are pervaded by localised swarms of quartz filled pure extension and extensional shear fractures hosting goldscheelite mineralization. The swarms comprise networks or æstockworksÆ of veins that strike NE, are subvertical and form subperpendicular to the shear zone fabric. Vein frequency across strike is typically ~1 m-1, with most veins five to ten centimetres thick and vertically continuous for up to ~20 m. Many of the veins show delicately banded internal textures that are parallel to the vein margins. These bands/lamina indicate incremental growth and are defined by a variation in grain size or alternatively by thin slivers of wallrock schist, though typically uncommon. The majority of veins are overprinted by a weak plastic deformation, although primary structures are largely preserved. This deformation has produced subgrain structures, migration of grain boundaries with sutured margins and undulose extinction of grains. These microstructural observations possibly indicate that temperatures were around 300¦C during stockwork vein formation. In general, the mode of brittle failure that developed the stockwork veins can be directly related to lithological variation. The geometry of stockwork veins indicate that local vertical shortening and extension occurred in the Intrashear sequence of the HMSZ synkinematically with thrusting. Localised extension was mainly parallel to the structural trend; that is, it took place perpendicular to the direction of inferred thrusting. The development of lateral ramps most likely gave rise to extension in parts of the shear zone during continuous shortening to form swarms of stockwork veins.

Jan 1, 2004

By F R. M Pires, R M. Carvalho

Supergene processes in banded iron formation (BIF) result in important dissolution, material transport and simultaneous disorder of the residual bands. The rock physical properties such as density, porosity and rheology change during the weathering attack. The itabirite, Paleoproterozoic metamorphic BIF from Quadrilßtero Ferrffero (QF) û Brazil, shows several weathered facies. Strong linking between topographic surface, rock density and iron grade occurs within the weathered zones. This linking is due to partial dissolution of silica and carbonate from itabirite and gravitational rotation and break of the remaining blades, generating kink-like slump structures. The original itabirite density, 3.7 t/m3, decrease at the first leaching steps, until 2.7 t/m3, and increase at the end of the leaching process until 3.6 t/m3. Iron grade increases from 38 per cent to 68 per cent and depressions (sinkhole), subsequently filled by Cenozoic basinal sediments, are developed over the enrichment zones. The formation of important supergene iron ore deposits of QF is intimately related to such a process. Several iron deposits at QF, such as Pico do Itabirito, Fßbrica Nova, Casa de Pedra, Tamanduß, -gua Claras, Cappo Xavier, etc., reveal the aspects related to the proposed evolution, implying that the formational process of the soft iron ores had a regional character. Granular medium model helped in the understanding of the development of the structure and the formation of the deposits. A numerical model has been developed in order to simulate a leaching system in a two-dimensional matrix, composed of two types of materials: leachable and unleachable. Equal volume proportion and vertical banding were considered. Drilling data was used as multipoint attractors to remove leachable matrix nodes.

Jan 1, 2002

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Salama, J Greberg, B Skawina

In today’s underground mass mining, the orepass is an important part of the infrastructure as it connects two or more mine levels and is used for conveying or storing large amounts of material. One of the main risks related to an orepass is when operational or structural failure occurs, leading to long-term loss of functionality. Developing or rehabilitating an orepass when major failure has occurred is a time-consuming and expensive operation, and the risk of a long-term orepass loss motivates the development of alternative transportation strategies to ensure the continuation of smooth operations in large underground systems. The study presented in this paper has been done at the Loussavaara Kiirunavaara AB Malmberget mine in Sweden, where iron ore deposits are being extracted using sublevel caving. The study analyses the transportation system in one of the mine’s orebodies using discrete event simulation, with a focus on maintaining ore transportation in the event of the loss of an orepass.CITATION:Skawina, B, Greberg, J, Jonsson, K and Salama, A, 2016. Orepass loss mitigation approach in Malmberget mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 617–622 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

By I Swane, R Rait, A Robertson

Geochemical assessment of mine waste materials prior to commencement of a proposed mining operation is a fundamental component of mine feasibility studies and the regulatory approvals process. Static and kinetic geochemical test methodologies are widely used to predict the geochemical nature of mine waste materials and to develop strategies for managing potentially æhostileÆ materials. These data can also be integrated with data from other fundamental studies such as hydrogeology to predict specific environmental outcomes and potential impacts at mine closure and post-closure.A case study is presented for a proposed open pit gold mine in Mongolia, which illustrates how geochemical, hydrogeological and groundwater quality data can be used as part of a geochemical modelling process to predict the final pit lake water quality over time. A series of static and kinetic test geochemical test programs were completed and acquired data integrated with hydrogeological and groundwater quality data provided by the proponent. A widely used geochemical modelling program (PHREEQC) was used to develop the geochemical model and predict water chemistry in the pit void after mine closure. Sensitivity analyses were completed to explore the effects on the model output of groundwater to leachate water ratio, pit wall rock type and climate.Modelling has indicated that pit void water should be pH circum-neutral at mine closure and should remain within Mongolian and World Bank water quality guideline limits under the modelled simulation most likely to occur in the field. Final void water salinity is expected to increase eight fold over 14 years after end of mine life due to a continuous flux of salts (particularly sulfate salts) into the pit lake whilst the pit lake volume will remain relatively constant due to evaporation and a slow recharge rate. Dissolved metal and sulfate salt concentrations in pit water are also predicted to increase over time and could be moderately elevated compared to applied water quality guideline values. Some of the metal concentrations, however, may be lower as these would be expected to precipitate at circum-neutral pH and greater. Recommended additional assessment work on the project when mining commences includes determining the magnitude of adsorption and co-precipitation of metals occurring in the pit void water/sludge system.CITATION:Robertson, A, Rait, R and Swane, I, 2013. Geochemical assessment of mine waste materials and prediction of final pit lake water quality at a proposed gold mine in Mongolia, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 165-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By A Bennett, S Arndt

Minerals and Metals Group Pty Ltd (Golden Grove Mine) commissioned a comprehensive study of the life of mine using advanced 3D stress modelling. Essential input into the modelling was the proposed mining sequence, itself the culmination of years of planning and geotechnical experience gained in comparing actual performance to predictions. The modelling approach addressed the whole of mine at a scale of 5 km. There were however several magnitudes of scale to address, from the scale of laboratory testing (0.05 m), to drive size (5 m), extraction size (50 m) and stope size (500 m). Scaling was therefore an integral part of the procedure. The constitutive rock properties in terms of peak and post-peak behaviour varied with the scale. At the laboratory scale, the constitutive relationships for all the main rock units were determined in 3D as well as recovering the in situ stress using the rock memory technique, deformation rate analysis (DRA), whereas at the larger scale the properties were varied to match observations.The modelling, using non-linear analysis to account for rock mass yield and peak-residual strength, demonstrated that if the planned extraction sequence and stope geometry had been pursued there was a high probability of large volumes of excess shear stress being released. However, it was not possible to identify whether the excess shear stress (ESS) will release as one large event or many smaller events. The mining approach was to modify the extraction sequence/stope geometry to manage the hazard. This is where the economic advantage can be realised.Alternatively or in combination with further modelling, the volume identified with the predicted high ESS or energy release could be intensively explored for structures having adverse orientation to the stress change and with sufficient areal extent to release the ESS. The microseismic data can be interrogated for the likelihood of a large event to support the hypothesis of a singular release versus multiple releases of smaller events. If the initial planned extraction sequence had to proceed as designed, changes to dimensioned stopes would be recommended for risk mitigation. Mine planning could as an option, modify the sequence and the extraction could then be remodelled.CITATION:Bennett, A, Arndt, S and Dight, P M, 2014. The economic advantages of detailed geotechnical assessments for extraction sequencing, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 243–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Y Gu, R Fandrich

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007