Search Documents

By J. F. Ednie

SCRAP metals to the value of more than a billion and a half dollars were recovered in the United States in 1939 for further use in industry. Few people have any true conception of the magnitude of the secondary-metal industry as related to that engaged in the production of the primary, or virgin, metals; of its importance, particularly when a shortage of primary metals exists, as at present; or of the advance that has been made in standardizing and improving the quality of its products. Of the iron and steel produced in the United States in 1939 (the data used in this article are largely taken from Bureau of Mines reports for that year) just over 50 per cent came from scrap and slightly less than 50 per cent from ore. Of the principal nonferrous metals-aluminum, anti-mony, copper, lead, nickel, tin, and zinc-63 per cent came from domestic ores and 37 per cent from scrap. Fig. 1 presents graphically the relative tonnage and value of primary and secondary production of ferrous and nonferrous metals. In this chart only purchased secondary metals are considered, the figures being exclusive of "home" or "plant" scrap which amounts to rather large figures in the iron and steel industry. Incidentally, the chart shows that from the tonnage standpoint the iron and steel industry is some twenty times larger than the nonferrous industry, though with regard to the value of the product the ratio drops to about two to one.

Jan 1, 1941

By Michael A. Gustafson, Fernando B. Sotelino

INTRODUCTION The degree of success of any new project will ultimately depend on two factors: (i) the underlying economic strength of the project; and (ii) how successfully the parties involved can coordinate their interests to establish a financing structure which indeed capitalizes on the project's inherent economic attractiveness. A project's underlying economic attractiveness is determined by its inherent comparative advantage in accessing the factors of production, combining these factors of production to create a product and marketing this product. Initially, the decision regarding whether to go ahead with the project - the go/no go decision - has to be based on its total ability to generate cash flow returns to project participants to compensate them for resources committed and risks undertaken. The extent to which project sponsors will actually benefit from the project's inherent economic attractiveness is fundamentally dependent on their ability to establish the long-term financing arrangement which best meets the objectives and constraints of each project participant and sources the most advantageous funding. The decision regarding the financing of the project, the "how-to-go" decision, is then an attempt to find the capital structure, consistent with market terms and conditions and sound financial management policies which will best: (i) match planned outflows with cash inflows; and (ii) maximize the return for project sponsors. This article makes use of a case study to illustrate the analytical process involved in dealing with the go/no go and the how-to-go decisions on a project. Though most commonly applied to project finance situations, the guideline described herein is equally applicable to other financing situations, such as leveraged buyouts and debt restructurings, where timely repayment of debt depends largely on the future cash flows to be generated by the entity being financed. Our case study is of a hypothetical expansion of an existing copper mining operation in Latin America. The company, Latin American Copper (LAC) currently has 147 million metric tons of proven sulphide ore reserves. The existing mine complex consists of an open pit mining operation and a conventional flotation plant with a processing capacity of 20,000 metric tons of ore per day. LAC sells copper concentrates primarily to Japanese custom smelters. The mine has been in operation for 5 years, fine copper production last year was 108,240 metric tons, and LAC currently has assets of $175 million and net worth of $135 million. Due to a recent increase in proven reserves, LAC is considering doubling the treatment capacity of its flotation plant to 40,000 tons per day, and expanding its mining capacity to meet the additional concentrator capacity (the "Project"). Project capital expenditures and incremental working capital have been estimated at approximately $210 million. The construction period is expected to cover one year, including a three-month start-up phase. The Project is to be funded by a combination of equity, senior debt, including both supplier credits and/or commercial bank term loans, and subordinated debt. LAC's shareholders are willing to commit a maximum of $50 million to the Project. A government development agency, which is also a minority shareholder, might be willing to lend approximately $40 million to LAC in the form of subordinated notes, depending on the ability of the Project to generate foreign exchange reserves. Commercial banks cannot be expected to offer loans with maturities longer than ten years. The Project is expected to increase the value of the firm because: (i) It will solidify the Company's position as a low-cost copper producer by taking advantage of economies of scale. As a result of the expansion, cash production costs are expected to decrease 7.0[c]/lb. and all-in costs 11.0[c]/lb; (ii) The potential earnings stream from the sulphide ore reserves will be realized

Jan 1, 1985

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By Pedro Bolsaitis, Paul M. Sullivan

The activities of zinc in liquid Zn-A1 alloys in the temperature range of 1000' to 1160°K were determined by means of the isopiestic technique. The results are in reasonable agreement with the previous values determined by the radioactive tracer dew point method. Slightly negative excess entropies of mixing were found. The measured activities suggest that the a function for these alloys is not a constant, as has frequently been assumed, but is better represented by two straight line segments of different slopes. THE thermodynamic data of Al-Z alloys have been the subject of investigation by many authors. However, in the recent compilation of such data by Hult-gren et al.,5 the conclusion is reached that none of the previous measurements are reliable or consistent with each other. Since then two new sets of measurements have been reported,2, 8 both laying claim to good accuracies, yet showing very significant disagreement in the measured activity coefficients of zinc in Zn-A1 alloys and in the magnitude and sign of the excess entropies of mixing. Information on the thermodynamics of the system is of particular interest for interpreting results of the Bureau of Mines research on refining of zinc by distillation of die cast scrap. The present study was undertaken as an independent check on the recent values obtained from dew point measurements 8 and electromotive force measurements.' The isopiestic method, first introduced by Herasy-menko,' was chosen because it is one of the few thermodynamic techniques which, in principle at least, is carried out under perfect equilibrium conditions. The disadvantage of the method is that data are obtained at various random compositions and temperatures, which makes the interpretation somewhat cumbersome. The random errors arising from temperature gradients and fluctuations appear to be comparable to those of other techniques, as evidenced by the magnitude of the estimated uncertainties in the calculated integral thermodynamic quantities. An advantage of the method is that each run provides a relatively large amount of data; thus, it is less time consuming than those methods where samples of each composition must be measured individually. EXPERIMENTAL PROCEDURE The activities of zinc in liquid Zn-A1 alloys were measured by the isopiestic method which uses the principle of the tendency toward equilibrium of a series of samples at various temperatures under an imposed vapor pressure of the more volatile component (i.e., zinc, in this case). The basic apparatus is shown in Fig. 1. The small graphite crucibles that contained the metal samples were 15 mm ID and 13 mm deep with approximately 3 mm wall thickness. Each crucible was notched at the top and bottom to allow easy passage of vapor from one to another. At the beginning of an experiment each crucible was weighed on an analytical balance. Zinc and aluminum of spectrographic purity (99.999 pct) were then weighed into the crucibles. The amounts of each metal added were such that initial compositions varied above and below equilibrium values. One crucible contained only pure zinc. After weighing, the crucibles were stacked with the pure zinc on the bottom (corresponding to the lowest temperature in the furnace) and richest aluminum alloys at the top. The entire stack of crucibles was then placed in the silica glass container "E" which was then sealed under vacuum. Sixteen to twenty calibrated Chromel-Alumel thermocouples were attached by wire along the length of the silica tube, one or more adjacent to each sample.

Jan 1, 1970

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By E. DeGolyer

WAR has wrought sharp and sudden changes in the pattern of the oil industry. The most obvious and most striking of such changes have been in the fields of transportation and refining. A third of the world's total oil production formerly started to market, tanker-borne, over the waters of the Gulf and Caribbean. Most of this oil went to our North Atlantic ports, supply points for the world's greatest consuming center. This tremendous traffic, disrupted by the loss of tankers as a result of requisition for military purposes and by the activity of enemy submarines, has had to be substituted largely by such lines of supply as could be improvised without loss of too much time. No single solution for this gigantic problem has been found nor is it likely to be entirely solved for some time to come. It has been solved in part, however, by rearrangement, reversals, and patching up of existing pipe-line systems; by overland transport of crude and products in tank cars on a scale never before attempted; by barging over inland waterways; and through the construction at long last of the "big-inch" line, the first leg of which is just being put into operation as far as Norris City, III. The tank-car traffic alone, reaching a peak of deliveries of 856,710 barrels per day into District 1 during the week ending Sept. 19, 1942, and accomplished at an expense of millions of dollars in extraordinary transportation costs, defrayed by the Defense Supply Corp. and by the mobilization of tank cars from all over the nation, is a story worth the telling but by some of those who directed it.

Jan 1, 1943

JOINT convention week has become a feature of the year with western mining men. The first was held at Denver in 1926, the second at Salt Lake City in 1927, and the third is about to take place at Los Angeles. Holding in the same city in one week the meetings of a number of related organizations has been .found to permit the development of a well-rounded program at the same time that it economizes time and money for the members, many of whom belong to several of the participating organizations. For the third time, the American Mining Congress, represented by its Western Division, of which Philip Wiseman is chairman, is taking the lead and assuming the main responsibility. The A.I.M.E. is furnishing the papers for two sessions and the California Development Association for one. The Southern California Section, Robert R. Boyd, chairman, is host for the Institute, but the Northern California, Nevada and Arizona sections have each contributed papers to the program, and will be represented at the meeting. It will be a real reunion of the mining men of the Southwest.

Sep 1, 1928

OFFICERS AND COMMITTEES C C Long, President John Chipman, Past President J S Smart, Jr, Vice President T D Jones, Treasurer R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y D C Johnston, Assistant Secretary

Jan 1, 1960

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.'.' While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham's law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After Americzn interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and de- clined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1953

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After American interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and declined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1952

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After Americzn interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and de- clined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1953

By H. K. Shearer

There were no important developments in the oil and gas industry in South Arkansas during 1935. Oil production, totaling 11,138,340 bbl., continued the decline that has been normal since 1925, but the decline from 1934 was only 278,600 bbl., or 2.5 per cent. The principal decline was in the Smackover field, while only the Champagnolle and Garland City fields showed notable increases. More wells were drilled than in any recent year, with a total of 123 completions. There were 44 oil wells, with a total reported initial daily production of 10,013 bbl., or an average of 227 bbl. per well. Two small gas wells were completed in Union County, where the gas is used locally for pumping and field operations. There were 77 dry holes, of which 28 were in or near oil fields and 49 were wildcats. Active drilling oper-at'ions declined from 65 at the beginning of 1935 to 41 at the end. Most of the drilling was done during the first part of the year, espr-chially (luring the flurry caused by the discovery late in 1934 of the "Taylor" sand production in the Champagnolle field, but the producing area was soon outlined. In November, 1935, the J. E. Crosbie, Inc., NO. 1 Sullivant in sec. 12, 17s. 14W., producing 560 bbl. per day at 3175 ft., opened a new sand lens in the eastern part of the field. The Camden "oil field," discovered in the last week of 1934, remained a one-well field, although four offset tests were drilled, besides a number of others in the immediate vicinity. Several interesting deep tests were drilled during the year, which added a great deal to the general knowledge of the subsurface formations and the structure of south Arkansas, but were not particularly encouraging as to prospects for the very deep production. First, the H. L. Hunt, No. 15 E. F. Gregory well in sec. 10, 17S., 14\W., in the Champagnolle field, was drilled to a depth of 6911 ft. It pene-trated red beds for 2982 ft., from 2943 to 5925 ft., mostly if riot entirely of Lower Cretaceous age. There was some anhydrite in the last 135 ft. of red beds. This was followed by 890 ft. of limestone, probahly Permian, and the rock salt was struck at 6815 ft. The salt is now generally conceded to be of Permian age. Finding salt in this well strongly indicates

Jan 1, 1936

By L. C. Armstrong

A. E. ROSS*—Mr. Armstrong in his paper stated that they had experienced considerable difficulty in drilling the quartz-feldspar intergrowths. The dia-mor~d loss was excessive and the diamond bits polished quite rapidly. Mr. Davidson, who presented the paper, stated that bortx stones in the range of 20 to 30 per carat had been used in the bits on this job. I would like to suggest the use of bits employing stones in the range of 60 to 100 per carat, an average of possibly 80 per carat. If these stones had been used the bits might have lasted longer and not polished so quickly. As a basis for this suggestion I would like to point out that in northern New York State we had at least two examples where bits employing stones in the range of 80 per carat had solved a difficult problem. Bits set with stones in the range of 20 to 30 per carat had been used previously and had failed. With the finer stones, the cost per foot of drilling decreased material1y. It should also be noted from a technical standpoint that the smaller stones require higher drilling speeds than the larger stones. Greater pressures are not normally necessary, and it is the higher speed which seems to be the major factor of importance. It should also be noted that the finer stones afford a greater number or cutting surfaces for the same carat weight in a bit. Then too, the smaller stones, by virtue of their size, serve as sharper cutting edges than larger stones. There is no doubt that the diamond bit employing smaller stones costs more to set than the bit using larger stones. However, with the technique developed at the shops of Sprague and Henwood, Inc., we feel that the relatively slight additional cost required to set these bits is more than paid for by the resultant lower drilling cost. We feel that the highest quality stone available is the most economical to use when hard fine grained rock is encountered. In summary, I would suggest that it might be possible to solve the problem presented in this paper by using a diamond bit employing stones at least as small as 80 per carat of the highest grade possible and by using the diamond bit at the highest speed available with modern drilling equipment. L. C. ARMSTRONG (author's reply) —It is generally agreed that the use of smaller, high-grade diamonds and of higher drilling speeds, as suggested by Mr. Ross, may be the best approach to the solution of the problem.

Jan 1, 1950