Search Documents

By R. L. Mauger, P. E. Damon, B. J. Giletti

This report includes the lead isotopic dating of a suite of galenas from Arizona and an application of the K-Ar method to the dating of a Laramide porphyry copper deposit, the Silver Bell Mining District. The lead isotopic data supports prior age assignments based upon geologic inference. The Silver Bell study illustrates the necessity of correlative geologic and petrographic investigations for the interpretation of the results of potassium-argon dating. LEAD ISOTOPIC DATING OF GALENAS FROM ARIZONA ORE DEPOSITS A group of galenas from Arizona ore deposits have been analyzed for lead isotope ratios. The results were used to calculate model ages by the. method of Russell, Stanton and Farquhar,l6 in which the age is calculated directly from the Pb206/Pb207 ratio. The use of Pb206/Pb207 ratios eliminates the errors inherent in measuring the abundance of Pb204. The Holmes-Houtermanns model is the other model commonly used for calculating model ages. Both models assume that any lead sample is composed of primeval and radiogenic components and the calculated age is the time at which the lead was extracted from its source area. Using the Holmes-Houtermanns model, a lead is ordinary if its isotopic ratios lie on an isochron. The growth curve that passes through the experimental point determines the U/Pb ratio in the source area. The RSF model assumes the source area for conformable leads is the mantle, that this has a uniform U/Pb ratio, and thus all ordinary leads must lie on a single growth curve, having a mantle U/Pb ratio. The definition of an ordinary lead differs between the models, and differences in age arise mainly from the assumptions made to evaluate parameters in the model equations. These assumptions depend on the hypothesis chosen to explain ore genesis. In the RSF Model, the Pb206/Pb207 ratio is derived as a function of time. The equation contains three undetermined parameters which are evaluated by assuming three known points lie on the curve. These are the following: 1) Primeval lead from the Canyon Diablo and Henbury meteorites, 2) Modern conformable leads which lie on Patterson's zero isochron, 3) Lead from the Bathurst, New Brunswick base metal deposits. The Bathurst deposits are postulated to be examples of "conformable base metal deposits", as proposed by Stanton.l9 A conformable deposit has a particular genetic history and, as a result, the orebody conforms to stratigraphic layering in the host rock. The metals are brought to the surface in volcanic rocks which originated in the mantle. Weathering products of these rocks, including sulfur and metals, accumulate in areas undergoing sedimentation. The formation of sulfide ion in the sediments by the action of sulfate reducing bacteria causes fixation of iron as pyrite. If the pyrite becomes concentrated in favorable stratigraphic horizons, any base metal deposit eventually formed by replacement of pyrite will have a strata bound character. Compaction and expulsion of pore water from the sediments at depth result in upward mobility of solutions containing soluble base metal chlorides. The strata with high pyrite content act as chemical traps for the base metal ions and replacement occurs. An important result of this general evolutionary model is that, if complete separation of lead and parent isotopes occurred during accumulation of the sediments, any ore deposit formed solely of metals derived from those sedimentary rocks will contain "conformable" lead. This would be true even if the actual ore deposit were formed at a later date by some epigenetic process. In this case, mineralization would be controlled by local conditions, and need not conform to stratigraphic layering. Also, any ore deposit containing lead derived from a mantle or mantle-like source, even though not conformable in Stanton's sense, will fall on the curve for conformable ores and thus give a meaningful model age. Model ages for Arizona galena deposits are listed in Table 1. Fig. 1 is a location map. Jerome-Humbolt District: Galenas from the United Verde mine at Jerome and the Iron King mine at Humbolt give model ages of 1750 m.y. and 1640 m.y. respectively. Both deposits are massive sulfide bodies in a host rock of older Precambrian

Jan 1, 1965

By H. Leslie Bullock

From aluminum to zirconium, the quantitative preponderance of quartz as a gangue material is well recognized. lf this material is to be efficiently removed, its variations must be understood. Variations with temperature are especially important. Too little attention has been given to the thermal polarization of quartz. Under closely controlled conditions, electrostatic upgrading is very reliable. For efficient separation, contact charges must be fostered and charges due to radiation, surface coatings, or thermal polarization avoided. This paper lists thermal transition points of quartz and shows their effect on actual separations. Simple separation tests with all factors except temperature held constant are recommended for determining transition points. With silica making up more than 27% of the earth's crust, its oxides comprising more than 59% of all igneous rocks, and quartz accounting for most of the main free oxides, the mining engineer is in constant contact with quartz, which may occur as a valuable mineral to be purified or, far more frequently, as a gangue material to be removed as completely and economically as possible. As a means of effecting such purification or removal, dry beneficiation is becoming more and more desirable owing to local water scarcities, wet waste disposal problems, or freezing conditions. One method that has been gaining particularly rapid acceptance is electrostatic beneficiation, or the separation of dry free-flowing materials by means of opposite surface charges, differences in potential, or differences in conductivity. Electrostatic beneficiation dates back to the 1870's, but only in recent years have newly developed methods and apparatus and a growing knowledge of solid-state physics widened the field for its economical application. Because the term "electrostatic beneficiation" has been rather loosely used in the literature, it has come to include both electrostatic and electrodynamic procedures. Attracting type separators, however, in which oper- ation is based on differences of surface charge or potential, are truly electrostatic, because the separation occurs in a substantially static field set up between oppositely charged surfaces. Separations with this type of equipment may occur at potentials as low as 1000 v and seldom require potentials as high as 30,000 v. In the new contact charge dielectric separators1 the variation in charge is produced by continuous contact and separation of the particles in the moving feed stream and these charges are fostered by the use of non-conducting support and feed surfaces and by handling the feed in the form of streams of appreciable depth. This favors uniformity of feed and allows higher production rates. The distinctive surface charge differences are set up on the separation of the particles according to Coehn's Law,2 which states that equal and opposite charges are generated on the separation of any two materials in contact and that the substance having the highest dielectric constant will be positively charged. The basic contact charge concept is reliable, but all electrical charges are transient and modified by the electrical conditions of the surroundings. Pyro-electric, photoelectric and radiant effects may modify or totally destroy the contact charges necessary for efficient separation, or contact with conducting surfaces may neutralize them. Such hostile conditions must be carefully guarded against, since they have led to many costly failures in the past. The most consistent difference in surface charges to insure good separation is produced by repeated uniform contact and separation of particles in the moving stream. The thickness of the feed stream possible with this method reduces the effect of contact with the supporting surfaces, but as some contact is inevitable, the best results may be assured by having the dielectric constants of the supporting surfaces between the dielectric constants of the substances to be separated. In general, the hard smooth surface of quartz makes it an ideal substance for electrostatic separation from most minerals. For instance, with calcite, starting with a feed containing 1.9% acid insolubles, one can produce a concentrate containing 0.30% acid insolubles with a tailings containing 21.7% acid insolubles and a yield of 92.8%. The color can be held at 92 or above and the tint at 1.7 or lower. Working with specularite iron ore, laboratory work has given a concentrate of 68.8% Fe., with an iron unit recovery of 96.7%. Excellent results are also in pros-

Jan 1, 1969

By W. S. Ayres

BACK in the early nineties the old Dickerson iron mine in Morris county, N. J., was operated by a vertical shaft 850 ft. deep and by a continuing slope for more than 1000 ft. more 011 an incline of 65", together making the vertical depth about 1800 ft. I was then the general superintendent there. This mine, named for a former governor of New Jersey, had been worked more or less continuously from long before the American Revolution and up to this particular time. The pumping equipment was of the old-time Cornish type, with its long pump-rods running down the vertical shaft and the slope to the sump at its bottom. It was operated by a large flywheel engine in the engine room and all angles were turned by the usual bobs. Saturday was the day fixed for lowering the "suction" into the deepened sump at the bottom of the advancing slope. The mine foreman had gone down with the morning shift to superintend this very vital and particular work, which consisted not only of lowering the "suction" into the sump immediately after the pump had been stopped, but of securing it to the rock and putting in the added sections of column-pipe and of tightening up the numerous bolts at their joints, all before the water rose to the point of working. At an appointed time during the forenoon I had agreed to go down into the mine and join the mine foreman in consultation over any difficulties that might have arisen. At the time agreed I went down by the cage to the bottom of the vertical 850-ft. shaft, and then by ladders down the slope for over 1000 ft. more.

Jan 1, 1930

By Carl Zapffe

In ten years the manganiferous iron ores of the Cuyuna District have become impor-tant in the iron industry. By Dec. 31, 1923, 4,735,806 tons had been produced. Dur-ing the war, the low-phosphorus black ores were in demand; now the high-phosphorus low,-silica brown ores are favored. It is estimated that the reserves of these ores are ample for some time. A RISE in less than ten years from obscurity into great prominence economically, tersely summarizes the history and status of the Cuyuna manganiferous iron ores. The Cuyuna district produces and ships mostly high-phosphorus iron ore, but the annual production of manganiferous iron ore is increasing rapidly and productions from individual mines are becoming more regular and more dependable as to grades and tonnages. This ore bids fair to become, shortly, the principal product of the district and is responsible for the present economic prominence of this district. The iron ores of the district have been described, by the author and others, in many publications and will not be discussed here. Lately the manganiferous iron ores have been given some attention, but the range and variations of chemical composition of the ores, the principal physical characteristics of the ores and their deposits, the relative importance of the different ores and their possibilities in future developments, and the life of the respective reserves have not been discussed. It is impossible to give all of this information with the positiveness necessary for it to constitute a reliable guide for investment or even for future mine development. Each property and each party presents a special case and deserves critical consideration. We are dealing with special ores and always with a set of new conditions. Sufficient information of a general nature can be given, however, to indicate the reason for and the trend of the presently augmented developments in the district.

Jan 12, 1924

By M. D. Arnold, H. J. Gonzalez, P. B. Crawford

A method is presented for estimating the effective directional permeability ratio and the direction of maximum and minimum permeabilities in anisotropic oil reservoirs. The method is based on the principle that production from a well in an anisotropic reservoir results in elliptical isopo-tentials about the well, rather than circular. Bottom-hole pressure data from three observation wells surrounding a producing well are required to apply the method. The method involves fitting field pressure data to a set of general charts of isopotentials and making a few simple calculations until a solution is found. The method is based on a steady-state equation for homogeneorrs fluid pow. In addition to the method, a brief discussion of the theory underlying it is presented. INTRODUCTION The existence of a different permeability in one direction than another in oil reservoirs has been mentioned in several papers. Hutchinson' reported laboratory tests on 10 limestone cores and pointed out that one-half of them showed significant, preferential, directional permeability ratios, the average being about 16:1. Johnson and Hughesz reported a permeability trend in the Bradford field in the northeast-southwest direction with flow being 25 to 30 per cent greater in that direction. Barfield, Jordan and Moore -eported an effective permeability ratio of 144:1 in the Spraberry. Crawford and Landrum4 showed that sweep efficiencies could often vary by a factor of two to four, and sometimes considerably more, due to variations in flooding direction and patterns in anisotropic media. These findings indicate that the poss'bility of anisotropy may be worthy of consideration in the development of an oil field. In considering this, it should first be determined if anisotropy exists. If it does, the direction of the maximum and minimum permeabilities and the ratio of their magnitudes are quantities which can be of value in planning the most efficient well-spacing patterns. Past methods of determining these quantities have included analysis of oriented cores and analysis of flooding performance of pilot injection patterns. In recent work, Elkins and Skov5 resented an analysis of the pressure behavior in the Spraberry which accounted for anisotropic permeability. This work was based on the transient pres- sure distribution in a porous and permeable medium, with the solution expressed as an exponential integral function involving rock and fluid properties. The purpose of this study is to provide a method, based on steady-state equations, of estimating the direction and relative magnitude of permeabilities in an oil reservoir from field pressure data and well locations only. The method presented is based on work by Muskat6 which shows that Laplace's equation represents the steady-state pressure distribution for homogeneous fluid flow in homogeneous, anisotropic media if the co-ordinates of the system are shrunk or expanded by replacing x with it is desirable that data be obtained early in the history of a field because knowledge of an anisotropic condition would allow new wells to be spaced in such a manner that reservoir development and subsequent secondary recovery programs could be planned more efficiently. THEORETICAL CONSIDERATIONS A brief discussion of the theoretical basis on which the graphical solution was developed is presented in this section. Muskat's two-dimensional6 olution for the pressure distribution in an homogeneous, anisotropic medium with an homogeneous fluid flowing can be algebraically manipulated to show that the isobaric lines are perfect ellipses. The ratio of the major axis to the minor axis, a/b, is related to the permeability ratio, k,/k,, as follows. alb = dk,/k,--...........(1) It can also be shown that the pressure varies linearly with the logarithm of the radial distance from the producing well. However, the gradient along any ray is a function of the orientation of that ray, and a ..xiable is present when anisotropy exists which cancels out for a radial (isotropic) system. For a system such as that described, a dimensionless pressure-drop ratio was developed which is completely independent of the actual magnitude of the pressures. This was done by arranging Muskat's solution in such a way that aIl variables cancelled out except k,/k, and well positions. However, this solution depends on having a co-ordinate system with axes coinciding with the major and minor axes of the elliptical isobars. Thus, it was necessary to introduce a co-ordinate system rotation factor. The two unknown variables are then k,/k. and 0, and the two measured dimensionless pressure-drop ratios are related to the unknown variables as follows.

By N. E. Truitt, D. G. Russell

The transient pressure behavior of a well which produces a single compressible fluid through a singte-plane wrticat fracture has been investigated mathematically. The fracture is assumed to possess infinite flow capacity, to be of limited mdial extent, and' to penetrate the producing formation completely in the vertical direction. Previous studies of vertically fractured wells have been concerned primarily with production rate performance or semisteady-state pressure behavior. This study was undertaken to ascertain the influence of vertical fractures on transient pressure tests such as pressure build-ups and flow tests. In a vertically fractured system, flow in the region nearest the fracture is practically linear, whereas farther away from the fracture essentially radial flow prevails. Thus, transient pressure analyses based on radial flow theory are somewhat inaccurate. As fracture penetration increases radially, kh values calcutated from pressure build-up and flow test curves become increasingly larger than true values. Failure to consider the effect of fracture penetration also introduces inaccuracies into the catculation of fracture length from the apparent skin factor and into the determination of average reservoir pressure. If the total length of the fracture is 20 per cent, or greater, of the drainage radius of the well, corrections must be made to pressure build-up and flow test results. Methods for correcting such results are discussed in this paper. For wells with prefracturing pressure build-up or flow test data, it is possible to estimate fracture length by comparison with postfracturing build-up or flow test results. In new wells or wells without prefracturing build-up or flow test data, fracture length must be estimated to correct the values obtained from analysis of pressure tests after fracturing. Fracturing efficiency calculations should be made whenever possible to provide an estimate of fracture length. Tables of the dimensionless pressure drop as a function of time and fracture penetration are included in this paper. Using these values should permit analysis of other types of transient pressure behavior in vertically fractured wells. INTRODUCTION Hydraulic fracturing has been used quite successfully for over a decade as a completion and stimulation technique in oil and gas wells completed in low-permeability reservoirs During this period a considerable amount of theory has evolved on the performance of hydraulically fractured reservoirs and on more efficient means of artificial fracturing. Although theory has been developed, no rigorous investigation has been made of pressure build-up and flow test behavior in such wells. Prats et al.1 first discussed the performance of vertically fractured reservoirs for the case of a compressible fluid. Their work was primarily concerned with production performance at constant flowing pressure. These authors also considered large-time (semisteady-state) constant production rate behavior for vertically fractured wells; however, transient pressure behavior at constant rate was not investigated. McGuire and Sikora10 and Dyes, Kemp, and Caudle2 employed an electrical analog to investigate the influence of artificial vertical fractures on well productivity and pressure build-up. They found that fractures which extend beyond 15 per cent of the drainage radius away from the well alter the position and slope of the straight-line portion of the build-up curve. They concluded that these effects must be considered both in the determination of the effective permeability of the formation and in any calculations of final build-up pressure. Although these authors did not undertake an exhaustive study of the influence of vertical fractures on pressure build-up performance, their limited results were quite interesting from the standpoint of the effects they demonstrated. In a more recent paper, Scott- reported the results of an investigation of the effect of vertical fractures on pressure behavior, which was conducted with a heat flow model. Scott's results appear to be consistent with those reported in Refs. 1 and 2. However, the effects of different fracture lengths on performance were not investigated. Pressure build-ups and transient flow tests are among the most diagnostic tools available to the reservoir engineer or production engineer. Since a very high percentage of present-day well completions incorporate the hydraulic fracturing technique, a definite need exists for information on the effect of fractures on transient pressure performance. For these reasons we have undertaken a rigorous study of pressure build-up and flow test behavior in vertically fractured reservoirs. The objectives of this study were (1) to obtain synthetic pressure build-up and flow test

Jan 1, 1965

By R. W. Fountain, W. D. Forgeng, G. M. Faulring

Precipitation of the phase Co3Ti (Cu3Au type) from a Co-5 pct Ti a11oy has been investigated using single-crystal X-ray diffraction techniques. Oscillation and transmission Laue patterns of specimens aged for short-time periods at 600" C indicate the formation of titanium-rich and titanium-poor zones coherent with the {100} matrix planes. Longer aging times at 600° C establish that the equilibrium phase also forms on the {100} matrix planes as platelets. These observations are corroborated by electron metallography; electron diffraction studies show the phase Co3Ti to be ordered. A probable sequence of the precipitation reaction is discussed. A previous publication by two of the present authors reported on the phase relations and precipitation in Co-Ti alloys containing up to 30 pct Ti.1 The results of this investigation established the existence of a new face-centered cubic inter metallic phase, ranging in composition from about 17.0 to 21.7 pct Ti at temperatures below 1000° C The decomposition of the fcc supersaturated solid solution was studied employing hardness and electrical resistivity measurements. The changes in hardness upon precipitation in alloys containing 3, 6, and 9 pct* Ti were found to be associated with an initial increase in hardness followed by a plateau and then a second, more pronounced hardness increase. Investigation of this behavior by electrical resistivity measurements suggested that two different kinetic processes were involved, which, when interpreted in terms of the kinetic relation,2-4 indicated that initial precipitation was in the form of thin plates. On continued aging, the plates impinged during the growth process. The general features of these findings have been confirmed by Bibring and Manenc,5 while, in addition, they report the phase to be ordered. The present investigation was undertaken to provide more definite information on the structural relationships between the precipitate and the matrix. EXPERIMENTAL PROCEDURE Single crystals of a (20-5 pct Ti alloy were prepared from the melt employing the Bridgman technique. Poly crystalline rod, 1/2 in. in diam, prepared from vacuum-melted material, was machined to 3/8- in. diam to remove any surface contamination that may have resulted from hot-working. The crystals were grown under a purified hydrogen atmosphere in high-purity alumina crucibles heated by induction. Considerable difficulty was encountered in attempting to grow monocrystals because of the high melting point of the alloy and the high solute concentration. However, one crystal about 6 in. long was obtained which was essentially a single crystal except for one or two very small grains around the periphery. The as-grown crystal was solution heat-treated for 24 hr at 1200°Cin a purified argon atmosphere and water-quenched. One-quarter-in. slices were taken from each end of the solution heat-treated crystal for chemical analyses, and the remainder of the crystal was mounted and oriented by the back reflection Laue Method. The chemical analysis of the crystal was as follows: Pct Ti Pct 0 Pct C Pct N Pct H Pet CO 5.29 0.08 0.004 0.002 0.0003 Balance By proper tilting of the crystal, it was possible to obtain slices 1/32 in. thick of [loo] and [110] orientation. The solution heat-treated crystal slices were sealed in silica capsules for the aging treatments, with titanium sponge placed at one end of the capsule to act as a getter. All slices were water-quenched from the aging temperatures, the capsules being broken under the water to ensure a rapid quench. Thinning of the slices for transmission X-ray studies was accomplished by a combination of mechanical and electrolytic techniques, the final thickness being about 0.1 mm. Laue patterns of the solution heat-treated crystal indicated that no strain was introduced by the thinning technique. ELECTRON METALLOGRAPHY After X-ray examination, the structural changes attending the precipitation were followed by examination of direct carbon replicas of polished and etched surfaces of the single-crystal slices and extracted phases. The earliest indication of significant structural change was observed after aging at 600°C The structure of a heavily etched, solution-treated crystal is shown in Fig. l(a). Aside from the etch pit pattern, no regularity of background structure is observed. On the other hand, in the background of the specimen heated for 500 hr at 600°C, the etching pattern shows a directionality indicating the influence of minute precipitate particles, Fig. l(b). On electrolytic dissolution of this specimen in 10 pct HC1 in alcohol, a large volume of very small, flattened cubes

Jan 1, 1962

By A. L. Mincher, W. F. Sheely

Mechanical properties of columbium have been studied over the temperature range of -196 to 1093oC. The decreased strengthening influence of cold-work at temperatures below ambient has been interpreted in terms of the Peierls-Nabarro effect. Maxima in the rate of strain hardening observed during tensile testing in the range 250-600°C. have been correlated with interstitial impurities to indicate the temperature ranges at which carbon, oxygen, and nitrogen, respectively, are responsible for strain aging. THE growing need for structural materials for use above the useful service temperatures of the iron-, nickel-, or cobalt-base alloys has caused the refractory metals to be considered as potential engineering materials. These metals, which include columbium, tantalum, molybdenum, and tungsten, are called refractory because the lowest melting point among them,that of columbium, is about 1000°C higher than the average melting temperatures of conventional high-temperature alloys. They are all body-centered cubic transition metals and, as such, their mechanical properties have basic characteristics which distinguish them from the face-centered cubic metals. For example, all show a much steeper rise in strength with decreasing temperature below room temperature than do the face-centered cubic metals, and their mechanical properties are strongly influenced by interstitially dissolved impurities. In order that these new metals may be used efficiently, it is necessary that their characteristics of behavior be fully known. In this paper, the mechanical properties of columbium will be examined over a wide range of temperatures. In particular, the influences of cold-work and individual species of interstitial impurity atoms on mechanical properties will be described, and basic mechanisms which may control the observed characteristics will be explored. EXPERIMENTAL The material used in this investigation was Union Carbide Metals Co. columbium roundels consolidated to four 4-in. diam ingots, three by consumable-electrode arc melting and one ingot by electron beam melting. Impurity contents of the ingots and methods of ingot conversion and treatment are summarized in Table I. The only metallic impurity occurring in any significant quantity was tantalum at about 0.1 pct. Iron, silicon, titanium, and zirconium were each less than 0.015 pct; boron was 1 ppm or less. This should have no appreciable influence on properties. The electron beam melted material, being the purest, will be used as the basis for comparison in the discussions to follow. Tensile tests were conducted from-196 to 1093oC, on both cold-worked and fully recrystallized arc-melted and electron-beam melted columbium using standard 1/4-in. diam, 1-in. long gage length test specimens. A strain-rate of 0.005 in. per in. per min was employed until the 0.2 pct yield strength was achieved and then the strain-rate was increased to 0.05 in. per in. per min for the balance of the test. Samples were protected in an inert atmosphere at tests above 300°C. The tensile properties obtained on the electron-beam melted columbium, E, in both the cold-swaged and recrystallized conditions are given in Fig. 1. The yield strength data of Dyson, et al.,' obtained on recrystallized electron beam melted columbium and the tensile strength data reported by Tottle2 on powder metallurgy columbium are included in Fig. 1. The material used by Tottle had been purified by vacuum sintering. There is excellent agreement between Dyson's data and those obtained in the present investigation. The tensile strengths obtained by Tottle were slightly greater than those obtained in this investigation on electron-beam melted columbium but varied with temperature in a similar manner. Tottle's data showed a maximum in tensile strength near 500°C, as did our data on electron-beam melted material, and also showed a small maximum at 300°C. The significance of these maxima will become evident later in the discussion. The tensile properties of cold-swaged and recrys-tallized arc melted columbium are plotted in Fig. 2. It was found that the properties of the recrystallized arc-melted columbium from all three heats showed very close agreement except at temperatures between about 500" and 800°C. A reason for this range of disagreement will be suggested in the discussion. The generally good agreement, however, attests to the ability of cold-working and subsequent recrystal-lization to erase the effects of the three different primary breakdown procedures and to produce nearly equivalent structures in the samples derived from the three different heats. wesse13 reported tensile data on columbium having interstitial impurity contents between those of the

Jan 1, 1962

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.'.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955

By Samuel S. Wyer

Discussion of the paper of SAMUEL S. WYER, presented at the New York meeting February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 263 to 279. DAVID T. DAY, Washington, D. C.-I would like to ask whether the court decisions quoted in the paper are general, or do they represent one side of the case; if so, are there any decisions that represent more than one side of the case? Are they of general application, or do they affect only one side? Also, what is the difference between a pump and a compressor from the standpoint of the natural-gas industry? I notice stress is laid on the word "pump" in. connection with some of the legal decisions, and then it is stated. that they must not pump or compress above 300 lb. The question is, is a pump a compressor and a compressor a pump, under certain conditions? SAMUEL S. WYER, Columbus, Ohio.-Answering the first question, I will say that the decisions cover both sides of the case very thoroughly, and are uniformly on the side that a company is justified in the use of gas compressors; in other words, there are no decisions holding it to be illegal to use gas compressors, with the exception noted in Indiana, Kansas, and Oklahoma where you cannot go below atmospheric pressure. In regard to the second question, I think the engineers and the gas operators themselves are responsible for the confusion. It is because the use of the term "pump" is almost universal, and so many people have obtained the idea that the primary function of a gas compressor is to pump air into the gas, in order to increase the consumers' gas bills. I appreciate that it is very hard to draw a clear line of demarcation. between a pump and a compressor. The distinction I have always made myself, and which I think is a logical one, is that you do not get the pumping action until you get below atmospheric pressure. As far as the compression end is concerned, there is only one State, namely, Indiana, that has any statutory limitation with regard to how high the pressure may be increased in order to put the gas into the transmission lines. The State law in Indiana limits the maximum pressure to 300 lb. per square inch.

Jan 5, 1916

By B. G. Klugh

The present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglomerating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the application of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with ma-terials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited time allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace. The following microphotographs are arranged in the order of the degree of complete fusion to which the mass in question has been subjected, in effectively binding the particles together. A very notable fact here clearly demonstrated is that the degree of fusion to which the material has been subjected is inversely proportional to the reducibility of the product. The characteristic of the material under consideration to which reducibility is almost universally attributed call be progressively traced in the following arrangement, through the identity of the obvious microscopic constituent. Furthermore, the degree of fusion to which a bod? has been subjected is recorded in the presence of resultant products of fusion in that body. Such readjustment is generally apparent

Jan 1, 1914

By Donald W. Barnett

U.S. environmentalists have tended to oppose all new energy developments. Their efforts may be counterproductive because opposition to, say, offshore oil directly leads to the continued use of other energy sources that may have a higher social cost. Rather than attempting to eliminate all pollution from energy production, which would be prohibitively expensive, one should minimize the social cost of energy production for the given demand. Linear programming is used to rank various oils (California State and O.C.S., Gulf of Alaska, Prudhoe Bay, Athabasca tar sands, oil shale and certain foreign crudes) in terms of their social desirability. The objective is to minimize the cost of supplying the California market, subject to resource, sulphur and oil spill constraints. Social desirability is indicated by the inclusion of the oil in the optimal solution and the size of the associated shadow price. the larger the shadow price, the greater the benefits of increased production. The more negative, the greater the cost associated with forcing consumption of that fuel. The environmental shadow prices indicate the size of the trade-off between a particular environmental standard and minimum cost. The trade-offs can be surprisingly large. any reasonable spill standard can be achieved by changing the development pattern. Generally, the further offshore, the smaller is the environmental degradation, but the more expensive is the oil. Foreign oils can be economically and environmentally inferior to domestic oils. Crude from the California O.C.S., San Joaquin Valley end Prudhoe Bay appears a valuable resource, while the Gulf of Alaska, synthetic and foreign crudes appear marginal to submarginal.

Jan 1, 1977

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami's reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."' A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. ' J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957

By Charles A. Colton

The results of a series of analyses extending over a period of three weeks at the Cedar Point Iron Company's furnace, Port Henry, New York, are given in Tables I and 11. This furnace uses a very pure magnetite and Lehigh and Lackawanna anthracite. The flue leading the gas from the "down-comer" to the boilers was tapped by a 2 inch gas pipe, which carried the gas to the Orsat apparatus. The pressure of the gas not always being sufficient, owing to the small amount made, to force it into the apparatus, I omitted taking samples several days, and with the exception of the last three days of the campaign, made the analyses whenever opportunity offered. I find the Orsat apparatus, as described by Prof. Egleston," to work very well, with one exception. The CO is not absorbed as readily in the ammonia-copper solutiou as he states in his description of the apparatus, as many as 50, and sometimes GO, passes being necessary to absorb all the CO. The power of absorbing rapidly increases as the solution is used, and this would indicate that the more oxygen it contains the quicker will it do the work. Probably the addition of a small amount of some oxidizing agent would remedy this. When the furnace was working in its normal condition, I had no occasion for using the filter, the amount of fume being so small as not to canse any inconvenience. The gas burned with the flame peculiar to CO, and contained just enough solid particles to give it a slight reddish tinge.

Jan 1, 1879

By Charles A. Colton

(Read at the Amenia Meeting, October, 1877.) THE results of a series of analyses extending over a period of three weeks at the Cedar Point Iron Company's furnace, Port Henry, New York, are given in Tables I and II. This furnace uses a very pure magnetite and Lehigh and Lackawanna anthracite. The flue leading the gas from the "down-comer" to the boilers was tapped by a a inch gas pipe, which carried the gas to the Orsat apparatus. The pressure of the gas not always being sufficient, owing to the small amount made, to force it into the apparatus, I omitted taking samples several days, and with the exception of the last three days of the campaign, made the analyses whenever opportunity offered. I find the Orsat apparatus, as described by Prof. Egleston,* to work very well, with one exception. The CO is not absorbed as readily in the ammonia-copper solution as he states in his description of the apparatus, as many as 50, and sometimes 60, passes being necessary to absorb all the CO. The power of absorbing rapidly increases as the solution is used, and this would indicate that the more oxygen it contains the quicker will it do the work. Probably the addition of a small amount of some oxidizing agent would remedy this. When the furnace was working in its normal condition, I had no occasion for using the filter, the amount of fume being so small as not to cause any inconvenience. The gas burned with the flame peculiar to CO, and contained just enough solid particles to give it a slight reddish tinge. * See Transactions, II, 226; V, 487, 621.

Jan 1, 1878

By George W. Maynard

At the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, in their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.' The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper,which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas: read at the New york meeting of the Institute, February, 1885, I show. that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on aid advanced by chemists and metallurgists at home and abroad.

Jan 1, 1911

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By Francis H. Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1936

By R. H. Heyer, J. L. Bray, M. E. Carruthers

It is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-aluminum system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1 Others2'3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to determine the change in the copper-aluminum relations with respect to iron. Objects of the Investigation In certain investigations carried out by the authors for a plant producing a large tonnage of cast aluminum bronzes the structures

Jan 1, 1936