Search Documents

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By William B. Stephenson

The paper describes efficient and effective methods of automatically controlling sand pump installations. Particular reference is made to liquid-level controls actuating variable speed pump-driving units. Included is a discussion of various combinations of equipment, with schematic drawings. HERETOFORE many sand pump installations in the mining and metallurgical field involved guesswork as to the size of the pump and then simply direct-connecting it to a constant speed motor which was often large enough to do twice the work required. Considerable thought was given to mill location in an effort to avoid as much pumping as possible. Hillside design of mills with gravity flow of tailing was much to be desired. Power costs were low, construction was relatively cheap, and labor in many places meant nothing in comparison to the values derived from the ores being treated. Today most of these conditions are reversed. Ores are becoming more complex with lower values per ton of ore treated. Power is more expensive, construction is higher, and labor definitely takes a very important place in the profit and loss statement. Each piece of equipment incorporated in the design of a new mill is selected to provide highest efficiency based on careful metallurgical analysis of the ore to be treated both in good and poor markets. Each is designed with its flexibility in mind and with provision for adjustments in its performance to meet actual conditions in the operation of the mill. Sand pumps have taken an important position in mill design. Operators the world over are relying more and more on the performance of a sand pump in the efficient operating of their plant. Many ordinary jobs are being done today with pumps driven through adjustable pitch diameter V belt drives in order that changes in pump speed can be made easily to meet actual operating conditions. Operating costs have long since proved the folly of operating a pump at too high a speed for the volume and head to be overcome. Metallurgical results have shown the benefits derived from a smooth flow as contrasted with a surging flow from an uncontrolled pump. Construction costs have risen to such an extent that surge bins and other means formerly employed must be omitted from today's flowsheet. Several installations of considerable size and involving the use of automatic pump speed control have proved the adaptability of such controls since they were placed in service in recent years. In the following presentation each system discussed and illustrated schematically has been installed in one or more instances and has proved itself reliable and definitely economical from the standpoint of capital investment, operation and maintenance. Variable Volume-Head Speed Control: Probably the most popular, effective and efficient automatic control setup for sand pumping installations is the one shown schematically in fig. 1. Commonly used

Jan 1, 1951

By Grover J. Holt

IN order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.o.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the "straight wash" ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces-namely, low price of product and minimum amount of fines-iron-ore concentration has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. [ ] Table I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1943

By William B. Stephenson

The paper describes efficient and effective methods of automatically controlling sand pump installations. Particular reference is made to liquid-level controls actuating variable speed pump-driving units. Included is a discussion of various combinations of equipment, with schematic drawings. HERETOFORE many sand pump installations in the mining and metallurgical field involved guesswork as to the size of the pump and then simply direct-connecting it to a constant speed motor which was often large enough to do twice the work required. Considerable thought was given to mill location in an effort to avoid as much pumping as possible. Hillside design of mills with gravity flow of tailing was much to be desired. Power costs were low, construction was relatively cheap, and labor in many places meant nothing in comparison to the values derived from the ores being treated. Today most of these conditions are reversed. Ores are becoming more complex with lower values per ton of ore treated. Power is more expensive, construction is higher, and labor definitely takes a very important place in the profit and loss statement. Each piece of equipment incorporated in the design of a new mill is selected to provide highest efficiency based on careful metallurgical analysis of the ore to be treated both in good and poor markets. Each is designed with its flexibility in mind and with provision for adjustments in its performance to meet actual conditions in the operation of the mill. Sand pumps have taken an important position in mill design. Operators the world over are relying more and more on the performance of a sand pump in the efficient operating of their plant. Many ordinary jobs are being done today with pumps driven through adjustable pitch diameter V belt drives in order that changes in pump speed can be made easily to meet actual operating conditions. Operating costs have long since proved the folly of operating a pump at too high a speed for the volume and head to be overcome. Metallurgical results have shown the benefits derived from a smooth flow as contrasted with a surging flow from an uncontrolled pump. Construction costs have risen to such an extent that surge bins and other means formerly employed must be omitted from today's flowsheet. Several installations of considerable size and involving the use of automatic pump speed control have proved the adaptability of such controls since they were placed in service in recent years. In the following presentation each system discussed and illustrated schematically has been installed in one or more instances and has proved itself reliable and definitely economical from the standpoint of capital investment, operation and maintenance. Variable Volume-Head Speed Control: Probably the most popular, effective and efficient automatic control setup for sand pumping installations is the one shown schematically in fig. 1. Commonly used

Jan 1, 1951

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By J. L. Snoek

[ ] DISCUSSION J. L, SNOEK*-Stress-induced preferential diffusion in cubic body centered metals in the annealed state provides us with a powerful tool for determining the mobility of interstitially solved atoms as well as their location in the lattice and the exact nature of the distortion brought about in the lattice by their presence. Calculations given by D. Polder31 show that the distortion of the lattice, besides being proportional to the applied stress P, is also proportional to [VC, RT + xVCo] where T, V and Co are the temperature, molar volume of the solvent and molar concentration of the solute respectively and x is a constant describing the mutual interaction energy of the dissolved particles. This calculation obviously is no longer valid if x is negative and the abso¬lute value of xVCo surpasses that of RT. The lattice may then be expected to become tetragonal spontaneously. Such a spontaneous tetragonality seems to have been observed by W. Klemm and L, Grimm for the case of oxygen solved in vanadium.32 Measurements of the internal friction in cold worked iron containing carbon or nitrogen should provide us with information on the mobility as well as the preferential location of these particles in the iron lattice in the cold worked state. The work by T'ing-Sui Kê is a valuable contribution to this problem, The data obtained by T'ing Sui Kê and myself on cold worked samples of iron seem to indicate that carbon and nitrogen in these samples are found either in the normal (1/2 , 0, 0) interstices or in a new preferential position created by the cold working. The latter positions in my opinion can hardly by anything else but the edges of the dislocations. The observed larger distances of diffusion might be explained by assuming that the carbon atoms when freed from a certain dislocation by thermal agitation must diffuse over several atom distances before being caught in another dislocation. The theory however needs working out and no doubt will be much more complicated than the one valid for the annealed state. T'ING-SUI KÊ (author's reply)-It is highly encouraging to read the written discussion given by Dr, Snoek who initiated the theory of stress-induced preferential diffusion in cubic body centered metals in the annealed state, Since the presentation of this paper, the author has done more experimental work on this subject which seems to be able to settle several of the points raised by Dr. Snoek. It has been found that such stress-induced preferential diffusion occurs also in the solid solutions of carbon,33 oxygen,34 and nitrogen35 in tantalum which has a body centered cubic structure. Analysis of the shape of the observed internal friction. peaks indicates that the inter-

Jan 1, 1948

By P. K. Koh

Chi phase (body-centered cubic, a = 8.89A) was found in as-cast 23 pct Cr-10 pct Mo-Fe alloy as well as in heat-treated 316, 316L, 317, and modified 446 stainless steels. Chi phase resembles sigma phase in its metastability, chemical composition, and brittleness. Microstructure and some of physical properties of chi phase were developed. MOLYBDENUM has been established as a desirable alloying element for the enhancement of corrosion resistance in Cr-Ni steels and creep and rupture strength in high temperature alloys. On the debit side, however, the molybdenum addition has been known to stimulate u formation. When the molybdenum-bearing steels were subjected to prolonged heating at elevated temperatures, losses of corrosion resistance and/or ductility have been observed. Andrews1,2 first found the existence of a new phase among the anodic FeC13 extracts from type 316 stainless steel solution treated and then reheated from 800" to 1100°C. This phase was designated x and was identified by diffraction patterns as of body-centered cubic structure with a value equal to 8.89? and similar to that of a manganese. He found that the x phase in this steel always coexisted with s phase, but failed to distinguish one from the other by metallographic technique. No definite conclusion was drawn regarding the equilibrium temperature ranges of these two phases. The appearance of Andrew's work recalled an un- explained structure observed several years ago at the Allegheny Ludlum Research Laboratories during the investigation of an experimental alloy containing 25 pct Cr, 10 pct Mo, and balance Fe. X-ray diffraction patterns on the as-cast material revealed the presence of a body-centered cubic phase having a lattice parameter of 8.89?. The structure was sufficiently similar to that of y chromium that for a time it was thought that the structure might be caused by the presence of some undissolved electrolytic chromium particles. The alloy as-cast was so brittle that it shattered after the slightest hot reduction by hammer cogging. This paper gives the results of some metallographic and X-ray diffraction studies on x phase as found in several experimental alloys as well as a few molybdenum-bearing commercial stainless steels. The analyses of materials studied were as shown in Table I. Experimental Procedure Metallography: Solid specimens were polished mechanically and etched in boiling 50 pct HC1 solution in order to best delineate x and s phases in the alloys studied. X-Ray Diffraction: The difficulty of satisfactorily developing diffraction lines for s phase in solid specimens has been previously reported by Bindari, Koh, and Zmeskal.V or this reason all specimens used in this investigation were subjected to anodic

Jan 1, 1954

By P. D. Hunt, I. Johnson, M. G. Chasanov, H. M. Feder

The solubilities of the transition metals from scundium to nickel, inclusive, in liquid cadmium were determined by sampling saturated solutions. At 400°C these solubilities (ppm) are:Sc, Co, 22; Ni, 12000. Relative partial molal enthalpies and excess partial molal entropies at infinite dilution for the solutes Cr, Mn, Fe, and Co are compared zoitlz similar data for the post-transition metals. Three new intermetallic phases, ScCd,, TiCd, and Ti,Cd, encozaztered in the course of this work, are reported. Measurements of the solubility of the 3-d transition metals in liquid cadmium have been reported' only for iron. The present measurements for the entire series were made as an aid to the study of the systematics of alloy formation. EXPERIMENTAL The apparatus and sampling techniques used for the solubility determinations were similar to those described by Martin etal.' Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple sheathed in recrystallized alumina and immersed in the solution. The thermocouple was recalibrated periodically during the course of the investigation. Thermocouple voltages were measured to the neares 0.01 mv with a Rubicon model 2732 potentiometer. A scaled-down version of the apparratus, in which the total metal charge was about 90 g, was employed to measure the solubility of scandium. Two-mm ID Vycor filter pipets were used to sample the scandium-cadmiurn solutions; the samples weighed about 2g- Cadmium with a minimum purity of 99.95 pct was used; the only impurities detected spectrochem-ically were C'u and Mg, both less than 10 ppm. The purities of the other metals were: scandium, 99.9 pct; titanium. 99.92 pct; vanadium, 99.9 pct; chromium, 99).99 pct; manganese, 99.9+ pct; iron, 99.90 pct; cobalt, 99.95 pct; and nickel, 99.96 pct. Solidified melts were routinely analyzed spectro-graphically. No significant contamination by the crucible, sampling pipets, or other materials of construction was observed. The entire specimen obtained by sampling was dissolved to preclude analytical errors due to segregation on cooling. Colorimetric methods3 were used for the analyses of cobalt (2-nitroso-l-naphthol), manganese (permanganate), nickel (dimethylglyoxime), titanium (peroxide), and vanadium (thiocyanate).4 Chromium, iron, and scandium were neutron-irradiated to produce The dissolved samples were gamma-counted to determine solute concentration.For the separation of intermediate phases from cadmium-rich alloys selective leaching by saturated ammonium nitrate solutions was employed. The concentration of cadmium in the successive leaches was followed polarographically and the process was terminated when the rate of cadmium dissolution decreased markedly. For the further investigation of intermediate phases 1/4- in. diam powder compacts were pressed at 80,000 psi and annealed in argon at 315" to 330°C for 10 days. Larger quantities of alloys were prepared in sealed tantalum capsules heated in a rocking furnace.

Jan 1, 1962

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ballmilling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described .2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unite and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By E.G. Lewis, l.M. Barker

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By L. M. Barker, E. G. Lewis

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By L. D. Jaffe, D. C. Buffum, F. L. Carr, M. Goldman

IN an earlier investigation by Jaffe and Buffum,' a time-temperature transformation diagram for isothermal temper embrittlement of an SAE 3140 steel showed some suggestion of two overlapping "noses." These authors mentioned, as a possible explanation, that their specimens embrittled at 525°C were slightly softer than expected, perhaps because of some slight unknown variation in tempering treatment. Because a double nose would be of considerable importance in elucidating the mechanism of the temper brittleness reaction,' it appeared worthwhile to redetermine the portion of the diagram near 525°C. The same heat of SAE 3140 steel was used as in the previous work, and experimental procedures were the same.' Blanks were austenitized 1 hr at 900°C, water-quenched, tempered 1 hr at 675°C, and water-quenched. Groups were then embrittled isothermally at the temperatures and for the times shown in Table I, and water-quenched. For comparison, one series was tempered various times at 675°C, water-quenched, and given no further treatment. V-notched Charpy impact specimens machined from the blanks were tested over a range of temperatures. Energy absorption and percentage of fibrous fracture were plotted vs test temperature for each group, utilizing both the new data and those for the same treatment obtained in the earlier work,' except that the earlier data at 525°C were discarded.* are given in Table I. After a small correction (-0.28°C/BHN) for the variation of hardness" from Rockwell C24, the transition temperatures were plotted against embrittling time for each embrittling temperature, using the data of Table I for the range of treatments covered there, and using previous dataL for other treatments. By cross-plotting, Fig. 1 was finally obtained. It appears from this figure that if there are two noses to the time-temperature-transformation diagram for isothermal temper embrittlement of SAE 3140 steel, the upper nose must lie above 575°C. As interest had been primarily in the region near 525°C, a thorough study of embrittlement above 575°C was not made. Fig. 1 shows that such a study is needed, especially since preliminary measurements at the tempering temperature of 675°C reveal much more rapid embrittlement than would be expected from the data at lower temperatures. The transition temperature increased, approximately, as the logarithm of the tempering time (about 81/2°C, after correction for hardness, for each doubling of the time).& Since three tensile specimens tempered 240 hr at 675°C and water-quenched had an average yield-tensile ratio of 0.844, with 70.7 pct reduction of area, it is assumed1 that the tempering temperature is not above Ae1. The omission of a quench-and-reheat operation below Ae1, for the groups tempered at 675°C, as compared to groups embrittled at lower temperatures, should not affect results." More detailed investigation of embrittlement above 575°C is now under way.

Jan 1, 1954

A general discussion on the subject of Crushing and Grinding was held on August 24, 1927, during the meeting of the Institute at Salt, Lake City. G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well undrr way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progrcss Report covering their work to date." Progress Report J. Gross, Salt Lake City, Utah.—-This has not been a simple problem, and when I tell you that me can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that dors riot appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correet. The first thing that was realized in this problem ass that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. we realized that if we tried to measure the results of crushing or grinding by the ordiuary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surfaee, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought. was a method whereby we could measure surface on crushed particles or, we will sag., on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realizcd that it would be rather a corn-

Jan 1, 1928

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer's knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen's bridge') was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946