Search Documents

By Harry P. McClintock, Alec M. Crowell

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

Discussion of the paper of G. Howell Clevenger and Bhupendranath Ray, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2437 to 2475. ALLERTON S. CUSHMAN,* Washington, D. C.:-I am very much interested in the subject matter of this paper. I have had occasion to speak to this question before. There has recently been so much written and said and claimed about the effect produced by the addition of small quantities of copper to steel that there is certainly an impression abroad that a new and wonderful cure-all has been discovered. Are we facing a method of alchemy by which, at the expenditure of very little trouble and only a few cents' worth of copper per ton, the well-known characteristics of steel with respect to some features are so marvelously changed as in effect to produce a new metal ? I am a great believer in the future of the iron and steel alloy field. I do not think that with all the advances we have made in metallurgy we have begun to scratch the possibilities of usefulness to mankind in the exploration of the alloy field, and I include in that alloy field even what might be designated as the dilute alloy field; that is to say, where a very small quantity of a metal alloyed with iron and steel confers upon it some new or extraordinary qualities. With respect to many of the physical characteristics of the copper-iron or copper-steel alloys I am not particularly competent to speak. With respect, however, to the investigation of corrosion problems and with respect to claims made with regard to resistance to corrosion, I am competent to speak insofar as I have specialized to some extent in that field and have given up a great deal of my time for a great many years to a study of it. Some years ago, being particularly interested in the study of corrosion problems, I received the very generous permission of a large manufacturing concern to use their large open-hearth furnaces any way I saw fit for exploring this particular field. There is not a metallurgist in this room who will not realize the generosity of a manufacturing company who would permit a man to pursue a theory and give him as his material to work with 60 tons of molten metal. At all events, I threw copper into the open-hearth furnace. I explored this alloy field, not in a ittle crucible in which I had to take out portions and have them

Jan 12, 1913

PAST PRESIDENT WILLIS MCGERALD PEIRCE New York City PRESIDENT-ELECT AND TREASURER ANDREW FLETCHER New York City VICE-PRESIDENTS O B J FRASER, New York City J B MORROW,' Pittsburgh, Pa. J L GILLSON, Wilmington, Del L F REINARTZ, Middletown, O PHILIP KRAFT, New York City W THOMAS,' Tucson, Ariz.

Jan 1, 1952

PRESIDENT Michael Lawrence Haider New York City PAST PRESIDENT Willis McGerald Peirce New York City VICE-PRESIDENTS 0. B. J. Fraser, New York City J. B. Morrow, Pittsburgh, Pa. J. L Gillson, Wilmington, Del. ' L F. Reinartz, Middletown, 0. Philip Kraft, New York City R. W. Thomas, Tucson, Ariz

Jan 1, 1952

[ ] Granville S. Borden (Mining Taxation, P. 1049) has written two other published articles on the subject, Taxation and Mineral Resources, and An Income Tax Program for Mineral Producers. Both articles appeared in Mining Engineering. He is presently employed by Standard Oil Co. of California as a special tax counsel. He holds an LL. B and an LL. M from George Washington University and a Bachelor of Science in Mining from the University of California. He has been chairman of the Taxation Committee of the Minerals Economics div. of the AIME. Borden fishes, plays golf, prospects, and performs mineral analysis as hobbies. [ ] Charles C. Towle (co-author, Uranium Deposits of the Grants District, New Mexico, P. 1037) graduated from the Colorado School of Mines with a degree in Geological Engineering. He was a member of Sigma Nu; Theta Tau, an honorary professional society; Blue Key, honorary social society; the glee club and quartet, and a member of the student council. He has been a mucker, driller, flotation operator and mill shift boss for the Clear Creek-Gilpin Co., Idaho Springs, Colo.; Geologist, chief engineer, and chief geologist for Patino Mines & Enterprises Consolidated, Inc., Bolivia; appraisal engineer and part-time geology student, Denver; office geologist for Geology Dept., special Engineering div., Sea Level Canal Studies, Panama Canal; and geologist, div. of Raw Materials, USAEC, Grand Junction, Colo. He is currently chief of the Denver Exploration Branch, div. of Raw Materials, USAEC, Denver. Towle was at one time a tournament golfer, playing three and four times a week. While working in South America he played in numerous tournaments. Today, although playing only occa sionally, he shoots in the low eighties.

Jan 1, 1952

By John A. Oberteuffer, Ionel Wechsler

High gradient magnetic separation, first introduced in 1968 as a means for the removal of very fine magnetic contaminants from clay, is no longer a new technology. Applications to a number of solid-solid and solid-fluid separation problems are now being exploited. Recent pilot tests and full-scale industrial installations of high gradient magnetic separators and filters have established their commercial viability and have demonstrated their superiority both in efficiency and cost effectiveness to conventional prior-art methods for water treatment and mineral processing. In high gradient magnetic separators, the magnetic trapping force for fine, even weakly magnetic particles is greatly increased over those available in previous magnetic separators. These very strong trapping forces are created on the edges of fine filamentary ferro- magnetic materials in the presence of a strong background magnetic field. In the basic cyclic high gradient magnetic separator, particles are trapped in the filamentary matrix until it is loaded, at which point the magnetic field is turned off, and the filter is back- flushed. Applications of cyclic high gradient magnetic filtration for water treatment include filtration of waste and process waters in steel mills. Treatment of hot rolling mill scale pit effluent and cold rolling mill emulsion has been successfully tested, and 2-meter diameter SALA-HGMF® magnetic filters have been installed at Japanese steel companies for the treatment of recirculating scrubber waters in a de-gas- sing system. A second major application in water treatment is for the polishing of recirculating waters in power and steam generating systems. High gradient magnetic filters can operate under conditions of

Jan 1, 1980

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By H. G. Doll

'This paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simp1e and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given. Introduction The problem of determining the angle and direction of the dip of the strata traversed by a drill hole has practical interest, and sometimes vital importance, which need not be emphasized to the oil industry. The need for that type of information has existed ever since wells have been drilled. Certainly it has not subsided, in spite of the numerous inventions and improvements made in other fields of the art of drill-hole exploration. The few examples given in this paper are but illustrative of this fact. In the past, methods have been devised, and used, to solve this problem, but generally they have met with limited success, possibly because they failed more or less to answer the requirements of a modern age for fast yet accurate measurements. If accurate, the results were obtained at the cost of very tedious and lengthy operations. The new S. P.* dipmeter service offered to the oil industry is the result of exhaustive and in this particular field. In 1032 a dipmeter and electromagnetic teleclinom-eter service was made available. The apparatus employed then was of a rather delicate and costly construction, and the measurements had to be made with precautions sometimes difficult to secure on the rig. Although the information given by the electromagnetic dipmeter was limited to the direction of the dip, very interesting results were obtained in California, Trinidad, Venezuela, Rumania and, most notably, in the Netherlands East Indies.+ Apparatus The S. P. dipmeter surveys present none of the drawbacks mentioned above. The apparatus is rugged and free from constructional complications, therefore well adapted to field use. This, combined with the new, basically simple approach to the problem, explains the rapidity of execution of the measurements. The results are remarkably accurate and they are complete, giving the

Jan 1, 1946

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By H. G. Doll

'This paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simp1e and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given. Introduction The problem of determining the angle and direction of the dip of the strata traversed by a drill hole has practical interest, and sometimes vital importance, which need not be emphasized to the oil industry. The need for that type of information has existed ever since wells have been drilled. Certainly it has not subsided, in spite of the numerous inventions and improvements made in other fields of the art of drill-hole exploration. The few examples given in this paper are but illustrative of this fact. In the past, methods have been devised, and used, to solve this problem, but generally they have met with limited success, possibly because they failed more or less to answer the requirements of a modern age for fast yet accurate measurements. If accurate, the results were obtained at the cost of very tedious and lengthy operations. The new S. P.* dipmeter service offered to the oil industry is the result of exhaustive and in this particular field. In 1032 a dipmeter and electromagnetic teleclinom-eter service was made available. The apparatus employed then was of a rather delicate and costly construction, and the measurements had to be made with precautions sometimes difficult to secure on the rig. Although the information given by the electromagnetic dipmeter was limited to the direction of the dip, very interesting results were obtained in California, Trinidad, Venezuela, Rumania and, most notably, in the Netherlands East Indies.+ Apparatus The S. P. dipmeter surveys present none of the drawbacks mentioned above. The apparatus is rugged and free from constructional complications, therefore well adapted to field use. This, combined with the new, basically simple approach to the problem, explains the rapidity of execution of the measurements. The results are remarkably accurate and they are complete, giving the

Jan 1, 1946

By John Finch

IN AUGUST, 1927, the writer examined certain copper deposits in New Mexico, which occur in beds of sandstones and shale, and in connection therewith reviewed the literature upon deposits of this type. Such deposits are known and have been reported upon at various points in Texas, Oklahoma, Arizona, Colorado, Wyoming and Utah, but in New Mexico they have been given more development than elsewhere and apparently occur there more conspicuously than in the other states. Some 25 years ago the writer examined deposits of similar origin in northern Arizona and more recently other deposits in western and southwestern Colorado, and these examinations have led him to realize how widely scattered are the deposits and how generally non-commercial they are. On superficial development, to one without a comprehension of their geologic nature, they are alluring on account of occasional small amounts of high-grade ore and much misplaced capital has been expended upon them. This paper, therefore, aims to present briefly certain theories of genesis, some details of which may possibly be new, and to lead up to practical conclusions which may be useful to other geologists and engineers. A bibliography of the more important literature upon such deposits is given below.2 Coffin's Bulletin upon the Radium, Uranium and Vanadium Deposits of Colorado, published in 1921, is a particularly clear discussion. The most comprehensive recent statement is Butler's. He describes a large number of occurrences in Utah and connects them up genetically with deposits in other states.

Jan 1, 1928

By H. S. George

A method of illumination that enhances the value of microscopic study of opaque materials, as in metallography. By simulating natural lighting, structures. That possess relief are given a natural appearance. An example is included of the revelation of a hitherto invisible microconstituent. Erroneous interpretation is avoided. For example, etching figures in ferrite, heretofore considered to be pits, are revealed as pyramids, standing in bas-relief. Suggestions on technique are given, for, while the method is obvious, practice and attention to detail are requisite. ON one occasion when it seemed desirable to reveal under the microscope not only the metallic structure of an alloy, but certain small non-metallic inclusions, that are ordinarily obliterated by etching, it was discovered that, by partly eclipsing the illuminating pencil of light rays, the residual light was thrown on the object from one side and the structure was brought out in relief. At the same time, the non-metallic inclusions were retained in clear view. In this first demonstration of lighting obliquely through the objective a card was thrust part way into the light beam between the arc iris, and the light filter; the shadow of the card on the filter served to locate its position. Next several stiff-paper disks of various diameters were mounted on flexible wires some plasticine on the other end of the wires made it easy to adjust and maintain a disk at any desired position in the light beam. To facilitate manipulation, an assortment of disks, was mounted on a wheel, as shown in Fig. 1. The purpose of partly eclipsing the light beam was discussed in an earlier paper.1 There it was pointed out that the usual methods of illuminating opaque objects for microscopic examination lend an, un-natural appearance to, the view, while the new method, which has been termed conical illumination, revels the true relationship of constituents by simulating natural lighting.

Jan 3, 1924

By Robert Archer

Two new alloys of the "strong alloy" class having improved fabricating qualities are described; also methods of producing alloys of the duralumin type with greater strength and hardness than previously obtained, are given. IT is about fifteen years since the development in Germany, largely by Alfred Wilm, of the aluminum alloy called duralumin. In this alloy, combining as it does the tensile strength of mild steel with the lightness and corrosion resistance of aluminum, a distinctly new material was presented to the engineering world. Despite the evident usefulness of this material, however, its commercial development has been slow, due in part to the difficulties involved in its fabrication. In view of the potentially great utility of strong aluminum alloys, it seemed desirable to find means of producing such alloys with better fabricating properties, and work was undertaken with this object in the laboratories of the Aluminum Company of America several years ago. This work has resulted in the production of two new types of aluminum alloy of the "strong alloy" class, having distinctly improved fabricating qualities. The knowledge gained has also made it possible to produce alloys of the duralumin type with greater strength and hardness than previously obtained. There have thus been made available some new engineering materials which it is the object of this paper to describe. These alloys, including duralumin, are fundamentally wrought alloys. Castings of the same compositions, heat-treated in the same manner give inferior physical properties, particularly as to ductility. The statements made subsequently concerning properties and heat treatment apply to material that has received sufficient working to thoroughly break down the cast structure. The material referred to has; in general, undergone a reduction in section of at least 80 per cent. by mechanical working. It may be mentioned in passing that other compositions have been found that are suitable for the production of the maximum physical properties in heat-treated castings.

Jan 2, 1925

Both drilling and production of oil decreased in Rumania during 1935. The drilling totaled 1,042,041 ft. and production 61,973,938 bhl., being a decrease of 8.5 and 1.6 per cent, respectively. Wells completed during the year totaled 198, of which 168 were oil wells, compared with 238 and 215, respectively, of 1934. No important discovery was made during the year. The only new field found was Valea Calugareasca, where the Credit Minier completed a small well on the westward plunge of the anticline. Drilling higher on the structure will probably prove the field to be of greater importance than the results of the discovery well indicate. The only other developments of importance were the extension of the Bucsani field, the opening up of a new area on the northeast of the salt at Moreni by Credit Minier and a minor extension of the West Gura Ocnitei field. At Calinesti, on the cast extension of the Moreni field, exploration work continued and a gas well was completed, but oil in commercial quantities is yet to be found.

Jan 1, 1936

Both drilling and production of oil decreased in Rumania during 1935. The drilling totaled 1,042,041 ft. and production 61,973,938 bhl., being a decrease of 8.5 and 1.6 per cent, respectively. Wells completed during the year totaled 198, of which 168 were oil wells, compared with 238 and 215, respectively, of 1934. No important discovery was made during the year. The only new field found was Valea Calugareasca, where the Credit Minier completed a small well on the westward plunge of the anticline. Drilling higher on the structure will probably prove the field to be of greater importance than the results of the discovery well indicate. The only other developments of importance were the extension of the Bucsani field, the opening up of a new area on the northeast of the salt at Moreni by Credit Minier and a minor extension of the West Gura Ocnitei field. At Calinesti, on the cast extension of the Moreni field, exploration work continued and a gas well was completed, but oil in commercial quantities is yet to be found.

Jan 1, 1936

By S. FROES ABRUE

No new oil fields were discovered in Brazil during 1945. Production for the year reached a total of 79.329 bbl., all coming from the four fields in the Baia basin; the Lobato-Joanes field produced 6728 bbl.; Aratu, 6717 bbl.; Candeias, 36,663 bbl. and Itaparica, 29,211 bbl. The total cumulative production from the Baia basin from 1939 to 1945 inclusive amounts to 210,000 bbl., all of which is utilized locally.

Jan 1, 1946

By G. A. Vissac, R. G. Minet, N. E. Sylvander

R. G. Minet—The authors' description of the remarkable progress made in the last few years in applying the fluidized solids technique to the problem of lignite drying and carbonization clearly demonstrates that engineering techniques available today may make many processes practical and profitable which a few years ago were considered otherwise. As pointed out in the article, the future of the carbonization step hinges on the value and utilization of low temperature tar. On paper, at any rate, this tar looks like a valuable raw material for the chemical industry to use. Some 50 to 60 pct may be converted to pitch for electrodes, roofing, road tars, and other valuable products; the 25 to 30 pct tar acids could conceivably form a basis for a new low cost resin or plastic of the phenolformalde-hyde type. Yet these materials are so new and dissimilar from available sources that much work must be undertaken by the chemical industry before they will be accepted. Now that the work of Dr. Perry and his colleagues has made a large supply of low temperature tar a real possibility, I would expect the chemical industry to accelerate its work in this field. On the basis of certain data available in the literature it appears possible to produce a more aromatic tar, although in smaller yield, by operating at temperatures in the range of 1300" to 1500°F. Operating a fluidized bed process for lignite at these conditions should be technically possible, at least, and could produce a tar having more familiar characteristics. I wonder if Dr. Parry would care to comment on such a possibility. Incidentally, in our own work on carbonizing coking coals in fluidized beds, using Ohio, Pennsylvania, and West Virginia high volatile bituminous coals, we have obtained yields which agree with the correlation given for tar yields vs moisture and ash-free volatile Btu. Our data are slightly under the line, but certainly in the range of the correlation. We have also obtained evidence in support of the authors' statement as to the effect of air on the process. In our pilot plant all the heat required for carbonizing is released by internal combustion of char in the fluidized bed in normal operation. We are also equipped to obtain all carbonization heat by external electric heaters on the shell of the carbonizer while introducing only an inert gas to the process. We note no difference in tar yield or characteristics between the two operations. In the case of the gas, however, it appears that some hydrogen is consumed by the air combustion. We would be interested in hearing in a little more detail about the hot dust and char handling problems at Sandow. Have the authors found char subject to spontaneous combustion? Have they ever tried a coking coal in their pilot plant? V. F. Parry (author's reply)—Production of a more aromatic tar by operation of the carbonizer at 1300" to 1500°F does not appear to be economical. 1) The capacity of a reactor operating at 1500°F would be 30 to 50 pct less than the capacity at 932 °F and the cost of processing would increase materially. 2) The cracking of tar vapors in a reactor requires appreciable time to complete the reactions and it is doubtful that considering the very short time of residence of tar vapors within the reactor (4 to 10 sec after evolution) the basic character of the tar would be changed significantly. This is indicated from the data reported in Table XIV. 3) General studies have shown that it is advisable to operate at the minimum temperature to produce the maximum tar and minimum gas. 4) Operating problems and the maintenance of vessels and reactors, and the hazards of handling hot char, increase with the temperature of carbonization. It is technically possible to operate at temperatures as high as 1500°F, but in my opinion it is not economical or desirable. We believe that the primary tar must be won in the simplest way and then processed alone to change its character for production of desired products. It is interesting to have confirmation of our observations on the reaction of air with the products of carbonization. The major reaction is with the char, fol-

Jan 1, 1957

By Frank Firmstone

IN 1871, two furnaces at the Glendon Iron Works, which had been blown out on account of the "coal strike," were altered from the open-top plan with side flues for collecting the gas, to closed tops with cup and cone. In one furnace the suppression of the side flues permitted a considerable alteration in the profile, but in the other (No. 5) no change in this respect was made; the side flues were simply bricked up and new ones cut through the sides close to the top. This furnace was in blast over four years, and we can, therefore, form a pretty good idea of the effect of the alterations on the furnace process. The principal dimensions are; Height 72'; greatest diameter, 18'; diameter at tuyeres, 8'; diameter of top, 10'; diameter at stock line (point at which the top of the materials is kept), 11'; cubic contents, 11,900 cubic feet. The table below shows the average results for periods of twenty-six weeks each. 1st, of the open-topped furnace; 2d, of the furnace with the first charger used, which was an ordinary cup and cone (diameter of cone 5' 2") 3d, with the charger used ever since, a "double" cone 7' 5" diameter outside, having a central opening 3' in diameter. The diagram (Plate II) shows the daily variations, in the grade of the irons for the same periods.* * In calculating the average grade of each day's iron, each twelve hours was taken by itself whenever more than two kinds of iron were made in the 24 hours, and the diagram drawn accordingly. By counting, it will be found that there were more such days with the single cone than with the "double" cone, and more with this than with the open top. † Anthracite.

Jan 1, 1876

By Z. F. Danes

Combination of gravity data and density logs makes it possible to determine the structural relief. Under a wide class of geologic conditions, the solution is unique, or limited to a single parametric system of solutions. As a useful byproduct, the method yields a new way to construct derivative maps, continue the field up or down, subtract regional anomalies, and perform smoothing. In the past, the problem of interpreting gravity anomalies in terms of structural geology was solved along two main lines: 1) A body of a certain shape and density contrast was assumed and the corresponding gravity anomaly calculated, analytically for simple bodies, graphically and/or numerically for more complex ones; then the computed anomaly was compared with the observed one, and the assumed shape corrected according to the differences between the two. 2) The anomaly is assumed to come from a warped interface between two media of different density; the relief of the warping is assumed small compared to the depth of burial, so that the structure can be approximated by a flat horizontal surface of variable density distribution. The first method is a standard technique, described in every text book on applied geophysics, and is well applicable, for bodies with predominant vertical dimension. The second one, probably first used by Tsuboi and Fuchida,' is mathematically more elegant. It applies to the fashionable field of integral transforms (Bullard and Cooper, 2 Tomoda and Aki, 3 Dean 4) and is useful mainly in cases when the vertical relief of the structures is comparatively small. 30th methods, tacitly or openly, assume a density discontinuity across the boundary of the two media, while within each medium the density is constant. However, the recent invention of the gamma-gamma

Jan 1, 1962

By R. G. Woolery

INTRODUCTION Since 1975, Union Carbide Corporation has been conducting uranium exploration in southwestern South Dakota. This program has resulted in the discovery of an ore body about eight miles north of Edgemont in Fall River County. The site which was previously mined for uranium in the 1950's and 1960's consists of 950 lode claims (approximately 20,000 acres) and is within the Black Hills National Forest. Preliminary development plans indicate that fewer than 200 surface acres will be involved in the mining and heap leaching of the ore. The ore occurs in both the Fall River and Lakota formations. The exploration to date has developed something in excess of two million tons of ore averaging -0.1% U308. About 75% of the ore is expected to be mined from underground with 25% coming from five to seven small pits. The surface mining will be extensions of previously mined areas with a disturbance of 35-40 new acres near 35-40 previously disturbed acres requiring a total reclamation of 70-80 acres. Several options for processing the ore including conventional milling by UCC, conventional milling in joint venture with another producer, and heap leaching are under consideration. This paper is concerned with the preliminary assessment of the heap leaching option based on the limited test work conducted on surface samples and on available cores from the deeper ones. The final design for a commercial operation will not be available until an underground bulk sample has been obtained and evaluated. Union Carbide has been operating heap leach facilities commercially since 1973 at Gas Hills, Wyoming and Maybell, Colorado. During this period, we have made considerable progress in heap construction

Jan 1, 1983