Search Documents

By Sandip K. Mukherjee, Anthony W. Laurito, Madan M. Singh, Jon C. Volkwein

In the past, little attention has been paid to the costs of ventilation, since it seldom represented a significant portion of the total mining cost. However, in recent years adverse mining conditions and increases in power charges have caused ventilation costs to rise. The federal regulations have set minimum standards for volumetric airflow rates in underground coal mines. As a mine develops, the air volume and pressure requirements increase. There are several methods by which the quantity of airflow to the mine and working faces can be increased. Some of the methods include (1) increasing main fan output or replacing the main fan by a new higher capacity fan, (2) reducing leakage across stoppings and overcasts, (3) adding a new ventilation shaft or borehole, (4) reducing resistance to airflow by reducing the resistance factor of the individual airways, increasing the number of airways (especially the parallel airways), or re- arranging the air courses by using the available entries, and (5) using auxiliary ventilation systems. This paper addresses the cost-benefit analysis of several of these alternatives as applied to a large operating coal mine located in southern Illinois. Pressure and quantity surveys were conducted under-ground, and measurements were taken at the main exhaust fans on the surface. The existing ventilation network was modeled by using the Penn State ventilation simulator. The input data included the configuration of branches, resistance of each branch (including a component for shock losses), and changes in pressure and volume. The results of the simulation were compared with the survey data to check the merits and accuracy of the model network. The net- work was designed to take into account shafts, major entries, overcasts, regulators, gob areas, working faces, and major leakage paths. The model network served as the basis for the cost analyses of networks designed for increased airflow. The applicable alternatives for increasing airflow were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each f the alternatives included capital, operating and maintenance costs. These costs were expressed as annual costs in terms of dollars per cfm of circulating air, taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. The result of these analyses show that for the short-range plans evaluated, the most cost-effective way of increasing airflow at this mine would be to reduce leakage through stoppings and overcasts.

Jan 1, 1982

By R. S. Wagner, W. C. Ellis

A new mechanism of crystal growth involving oapor, liquid, crnd solid phases explains many observations of the effect of implurities in crystal growth from the vapor. The role of the impuuitq is to form a liquid Solution with the crystalline tnalerial to be grown from the vapor. Since the solution is n prefevred site for deposition firorti the uapor, the liquid becorrles supersaturated. Crystal growth occurs by precipitatzon from the supersaturated liquid crt tlie solid-liquid zntevfnce. A crystalline defect, such as a screw dislocation, is not essetztial for VLS (vapor -liquid-solid) growth. The concept of the VLS mechanism is discussed in detail with reference to tire controlled growth of silicon crystals using gold, platinum, palladium, nickel, silver, or copper as an implurity agent. RECENTLY a short communication' described a new concept of crystal growth from the vapor, the VLS mechanism. In this paper we present a detailed description of the process and its application to the growth of silicon crystals and we discuss its relevance to existing concepts of .'whisker" crystal growth. Crystal growth from the vapor is usually explained by a theory proposed by Frank2 and developed in detail by Burton, Cabrera, and Frank.3 In this theory a screw dislocation terminating at the growth surface provides a self-perpetuating step. Accommodation of atoms at the step is energetically favorable, and is possible of much lower supersatu-ration than required for two-dimensional nucleation. Crystals of a unique form resulting from aniso-tropic growth from the vapor are "whisker" or filamentary ones. Such crystals have a lengthwise dimension orders of magnitude larger than those of the cross section. For most filamentary crystals both the fast-growth direction and directions of lateral growth have small Miller indices. The special growth form for a whisker crystal implies that the tip surface of the crystal must be a preferred growth site. sears4 proposed that, according to the Frank theory. a whisker contains a screw dislocation emergent at the growing tip. Such an axial defect provides a preferred growth site and accounts for unidirectional growth. The hypothesis was extended by Price. Vermilyea. and Webb," still implying the presence of a dislocation at the whisker tip. They postulated that impurities arriving at the fast-growing tip face become buried while those arriving on the surface of slow-growing lateral faces accumulate and thereby hinder growth. These considerations led to a whisker morphology. There is increasing evidence that most whisker crystals grown from the vapor are dislocation-free. Webb and his coworkers6 searched for an Eshelby twist7 in zinc? cadmium, iron. copper, silver, and palladium whisker crystals. They found unequivocal evidence for an axial screw dislocation in only one element, palladium. However, not every palladium crystal examined contained a dislocation. Observations with the electron microscope have failed to show dislocations in whisker crystals of zinc, silicon.9 and one morphology of AlN.10 Since many whiskers are completely free of dislocations, an axial dislocation does not appear to be required for whisker growth of many substances. A significant advance in understanding whisker growth has been a recognition of the need for impurities. This requirement has been clearly demonstrated for copper,11 iron,13 and silicon9-1 whiskers. For silicon, detailed studies proved conclusively that certain impurities, for example, nickel or gold, are essential. Another pertinent phenomenon which has received little attention is the presence of a liquid layer or droplets on the surface of some crystals growing from the vapor. Crystals in which this has been observed include p-toluidine,14 MoO3,15 ferrites,16 and silicon carbide.'" The liquid layers or globules were considered to be metastable phases, molecular complexes, or intermediate polymers originating from condensation of the vapor phase. The possibility has been suggested that the halide being reduced is condensed at the tip18 or adsorbed on the surface11 of a growing metal whisker, for example copper. The literature on whiskers discloses illustrations of rounded terminations at the tips. These appear. for example, on crystals of A12O3,19,20 sic,21 and BeO.22 For BeO, Edwards and Happel suggested that during growth of the whisker the rounded termination consisted of molten beryllium enclosed in a solid shell of BeO. A recent paper9 on the growth of silicon whiskers contains many observations pertinent to an understanding of the mechanisnl of whisker growth. These observations are summarized as follows. 1) Silicon whiskers are dislocation-free. 2) Certain impurities are essential for whisker growth. Without such impurities the silicon deposit is in the form of a film or consists of discrete polyhedral crystals.

Jan 1, 1965

By AIME AIME

IT IS not necessary to travel hundreds of miles from New York City to see examples of modern mining methods applied in tunnel work. In the various subway jobs, for instance, underground work is done on so large a scale as to justify the oft-quoted remark that here is the world's greatest mining camp. In such cases, however, the size of the excavation makes wholly disproportionate comparison with the haulage drift or adit level of the West. But in West Orange, N. J., Antonio -DiMarco is driving a tunnel from two headings on opposite sides of First Mountain, under contract with the town of West Orange, which is similar in nearly every respect to the type of work that must be done at the mines, and merits description as an example of fast and economical tunnel driving under conditions commonly met with by the mining engineer in more inaccessible parts.

Jan 1, 1931

By Richard H. Siller, Rex B. McLellan

A model for interstitial solid solutions has been considered in which a repulsive Potential exists between interstitial atoms in the solvent lattice. It has been shown that this model is consistent with the thermodynamic Properties of certain interstitial solid solutions. The model is then applied to the calculation of the variation of the diffusivity of carbon in au-tenite with composition. Although the energy levels at the saddle point, and thus the absolute values of dif-fusivity, cannot be calculated, it is shown that by taking the repulsive interactions between the diffusing atoms into account the functional form of the dependence of diffusivity on solute concentration can be derived. ThE composition dependence of the diffusivity, D, of carbon in austenite at a given temperature is well-known.'-3 smith3 tried to reconcile the observed composition dependence of D at 1000°C with the previously observed4 composition dependence of carbon activity using equations for D derived by arken5 and Fisher, Hollomon, and Turnbull,6 but was unsuccessful. In this paper we shall modify the approach of Fisher et al. by considering the "blocking" model7 for interstitial solid solutions, based on concept due to Speiser and Spretnak,' in which a repulsive potential exists between interstitial solute atoms in the solvent lattice, causing a certain number of interstitial sites to be "blocked" from occupancy by further solute atoms. We shall thus be able to describe the intimate relationship between the composition dependence of carbon diffusivity, a kinetic phenomenon, and the composition dependence of carbon activity in austenite. THEORY Consider for convenience one-dimensional interstitial diffusion in an fcc lattice in the [loo] direction. Fig. 1. Assume that solute atoms occupy octahedral sites only.7,9'10 These octahedral sites are located on {lOO} planes a/2Å apart. A solute atom, A, occupying an octahedral site on a {100 } plane denoted by 2, has twelve nearest-neighbor octahedral sites: four on plane 1, four on plane 2, and four on plane 3. Diffusion occurs when there is a net flux of solute atoms, through an imaginary plane shown with dashed lines, from plane 2 to plane 3. Fisher et al6. use the concept of activated complexes, as given in the theory of absolute reaction rates." They show that the number of solute atoms per cubic centimeter per second which pc — Fig. 1-Diagram showing the arrangement of octahedral sites (x) in the fcc lattice. pass in the direction of diffusion from activated to new interstitial position is: ?where C is the concentration of the solute in atoms per cubic centimeter, l/m + is the fraction of new interstitial positions corresponding to motion in the forward diffusion direction (transmission coefficient), ?F* is the free-energy difference between the activated complex and the reactants when each is in its standard state at the temperature of the reaction (independent of temperature and composition in the case of carbon in austenite), y is the activity coefficient of the solute species, and, finally, ym is the activity coefficient of the activated complex (assumed constant). The flux of atoms moving in the forward direction through an area of 1 sq cm perpendicular to the direction of diffusion is therefore: m+ Ym l ' atoms per second where is the distance between planes. The blocking model states that a nearest-neighbor octahedral site of a given solute atom has a probability, f, of being inaccessible to other solute atoms. The number of available sites for diffusion on a given plane will, therefore, depend on f, which is constant, and Nu, the number of solute atoms on that plane. The effect is to have more available sites in the diffusion direction, thereby increasing the net flux of solute atoms. This is reflected in the transmission coefficient, l/m. To calculate the transmission coefficient for solute

Jan 1, 1970

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900

Oceanographers are tooling up. Back of the build-up is Navy defense work and private business. Business is dipping toes in the ocean gingerly and not sure whether the motivation is based on logic or intuition. The problem is that new business opportunities in the oceans could explode rather than evolve. The question is when. At stake for earthlings are food supplies, mineral resources, oil and gas, weather forecasting, navigational systems, shore erosion control and sewage disposal, as primary targets. "Twenty years ago, offshore oil seemed a remote possibility for economic exploitation but today it is a reality. It became a reality largely because of the development of practical ocean seismic equipment and drilling platforms. Today the oil industry is looking at submerged-type drilling rigs. Mineral exploration in the sea is more expensive than on land now primarily because familiar land tools are being modified for sub- marine work." These were the ideas expressed by C. G. Welling of Lockheed Missiles & Space Co., at one of the many meetings that have taken place so far this year on development of marine resources. Welling's views indicate the rationale of companies that have already invested in the sea. Many companies, including those in mining, have observers who caution, "go slow." The continental shelfs and even the deep ocean floor represent to the mineral industries the age-old, enigmatic confrontation-is this the time to move? To no other industry, except Defense, are the results of correct timing so vital.

Jan 8, 1967

By E. P. Polushkin

This work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility of determining the amount of the constituents without separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. Suppose Fig. 1 represents a part of a photomicrograph on which the total area of the black figures is to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively. This is also true for the whole area of the photomicrograph. Therefore, to determine the total areas of the black and white figures we must first find the proportion between the sums of the medians and then divide the area of the whole photomicrograph in the same proportion.

Jan 1, 1925

By Lawrence Burkhart, S. B. Joo

Axially unsymmetric ordered circulation patterns on the surface of a hemispherical constant volume drop with forced Internal motion were considered as a manifestation of hydrodynamic instability, which was affected by internal flow as well as by the properties of the interface A simplified mathematical model was analyzed In order to study the mechanism of onset of interfacial circulation from a non-circulatory basic state. Values of the critical Reynolds numbers were obtained when the basic state became a fully developed rotational flow and the values changed for different interfacial properties. The work describes a heretofore unreported surface flow pattern on drop surfaces From a practical point of new, any motion in the interface of a droplet can have a significant effect of mass transfer rates in solvent extraction processes Although surface motion in droplets actual processing equipment is very complex, continued study of the fundamental nature of such phenomena should ultimately lead to more effective equipment design procedures.

Jan 1, 1981

Experiments on the Rate of Heat Transfer from a Hot Gas' to a Cooler Metallic Surface Members of the American Institute of Mining Engineers will be much interested in the subject of teat transfer from a hot gas to a cooler metallic surface, and although the book on this subject recently published by the Babcock & Wilcox Co., of New York, deals primarily with boilers, it contains a great deal of information which metallurgical engineers will find of great value. The book starts out with an introduction giving some of the current theories regarding this subject; it then describes in detail the experimental apparatus used, and the methods of conducting the experiment's and recording the data. Then follow some account of the determination of radiation losses in jackets and cooler; measurement of metal temperatures; detection and correction of errors; etc., concluding with a discussion of the results and derivation of corrective formula for heat absorption; heat pressure rate and specific heat of gas.

Jan 5, 1916

By J. E. Castle

THE title of this article is descriptive, but not complete, for psychological evaluation is almost as important as rigid economic evaluation. This refers to those human traits that cause people to be too optimistic about the projects they are sponsoring, to overlook obvious weaknesses, to base decisions on incomplete and inaccurate data, and to gloss over embarrassing problems. Investment of capital in a new industrial mineral project is warranted only after rigorous economic analyses based on unquestionable facts. A plunge into production cannot be justified solely because these minerals have been deposited in the ground and are therefore free. There are no specially favorable economic laws that make the business of industrial minerals more attractive than any other. The factors of supply and demand, marketing, technological changes, taxes, competition, and fluctuating prices apply as much to industrial minerals as to other business enterprises. What is more, industrial minerals are subject to the higher risks that all mining enterprises face.

Jan 6, 1958

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term ''burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the features of high frequency, great strength and shallow depth of the beginning burst have been found. There are some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By George C. Toland

In 1950 the phosphate fertilizer market warranted the design and construction of a new fertilizer plant by Cominco at Kimberley, B.C. The initial rated capacity of the plant was 70,000 tons per year of high- grade ammonium phosphate. The plant was placed on-stream in 1953. One of the major problems in operating the fertilizer plant was the disposal of the gypsum tailings slurry which was a by-product of phosphoric acid manufacture. The original weight of dry tailings produced by the mill was 500 tons per day. This quantity increased over the years until a projected 2200 tpd was selected for the pond design described in this paper. The original gypsum tailing area was located south of the fertilizer plant and adjacent to the St. Mary's River. By 1965 the original disposal area had proven inadequate and Cominco's engineering staff had selected a 500 acre disposal site to the east of the plant.

Jan 1, 1971

By A. Haas, L. Bubenicek

The Lorraine deposit of minette iron ore has been mined for more than a century. During this time, the economic conditions have changed frequently, and especially during the past decade. Thus, it has become economically prudent to proceed to new iron ore reserves with consideration of many and varied parameters. In the past, only traditional mining parameters were considered. Today, the quantity of information that must be taken into account is of such magnitude that the only practical means of data processing is by use of a digital computer and a mathematical model. One such model, based on geostatistics, was developed by G. Matheron. Much of the required input information, such as the petrology of ores, has been generated through IRSID investigations. This paper deals with several aspects of data processing in mining including information recording, reserves calculation, and stages of shrinking data in the calculation of mining iron beds, variograms, kriging, and tonnages.

Jan 1, 1969

By W. A. Backofen, B. B. Hundy

THE pole figure interpretation in a recent paper' on the torsion texture of copper was questioned in discussion,2 nd a simpler alternative interpretation was proposed. In the hope of reaching a positive decision in favor of one or the other, further studies were undertaken with 70-30 brass and Armco iron. This additional work has not answered all the questions about torsion textures, but the new pole figures do offer support for the original interpretation and show that the texture is more complicated than the alternative suggests. From the previous paper,' the appropriate method of describing the texture in a twisted bar is known to be a pole figure plotted on a plane tangent to the surface of the bar. The axes of the pole figure are chosen to coincide with directions in the tangent plane which are parallel and at right angles to the bar axis (the longitudinal direction, L.D., and the transverse direction, T.D.), for these directions define symmetry axes of the texture. Therefore any ideal orientation that might be selected to represent the texture gives the crystallographic plane parallel to the tangent plane and the crystallographic direction parallel to the axis of the torsion specimen. A unique texture was assumed in the original interpretation, and the four ideal orientations, (112) [111], (111) [112], (110) [001], and (112) [131], were used in its description. Of the four orientations, the first three provide possible slip directions along the direction labeled T.D. in the pole figure, which is one of maximum shear stress in a specimen being twisted. The alternative, however, simply considered the texture to be made up of two components, one a [Ill] alignment along the specimen axis with a random orientation about the axis as in the wire texture, and the other a superimposed orientation (110) [0011. Experimental evidence for this simpler interpretation was derived from two observations: 1—twisting did not alter the orientation of a single-crystal torsion specimen of a brass in which an octahedral plane was perpendicular (and a [Ill] direction parallel) to the axis, and 2—deformation bands with approximately the (110) [001] orientation were seen to develop in the crystal during the test. The new pole figures were obtained with a brass and an iron torsion specimen of 3/4 and 1 in. gage length diameter, respectively. After annealing, polishing, and twisting, seven rods, about 0.030 in. in diameter and with different orientations, were prepared from material near the surface of each specimen; these were required for the method of constructing pole figures by using a Geiger counter as developed by Norton.5 Since the shear strain gradient in plastic torsion is linear, it was readily computed that the material supplying the brass rods had been subjected to a shear strain of about 3.2, and that supplying the iron rods had received a shear strain of about 2. All details concerning specimen design, testing procedure, rod preparation, and use of the Norton technique can be found in ref. 1. Only this procedure was followed in working out the (111) and (100) pole figures for brass, Figs. 1 and 2. However, X-ray photograms were also involved in the construction of the (110) pole figure for Armco iron, Fig. 3. The photograms were made according to the conventional transmission diffraction technique using a small sheet taken parallel to the specimen surface and etched to a thickness of about 0.0025 in. They were especially important in locating the boundaries

Jan 1, 1954

By C. A. Stetefeldt

The purpose of this paper is to convince the managers of silvermills that their customary reports in regard to the percentage of silver saved are far from the truth. It may be unpleasant for them to have the proofs of this fact brought before the public, and for this rezson the author refrains from giving the names of the mines and mills from which the statistics here recorded were obtained. It may be asked: What is gained by informing the stockholders of our silver-mines that they receive incorrect reports? Will this increase their dividends or lessen their assessments? In the first place, it is always better to publish honest facts than fiction. In the second place, many superintendents believe in the correctness of their reports, and have no idea how much they deceive themselves. Finally, the knowledge that hitherto unexpected losses of silver take place may lead to the adoption of methods by which these losses are greatly reduced. These remarks refer also to smelting-works. The present paper, however, is concerned exclusively with amalgamation and lixiviation. The first and most important error is found in the inaccuracy of the commercial assay; the second in the incorrect sampling of tailings in amalgamation. Further, mills not doing custom-work, but reducing exclusively ores from mines to which the mills belong, are in the habit of weighing the ore only approximately and without making moisture-tests. Thus, a correct basis for calculating the actual percentage of silver extracted is lacking. The superintendent, then, finds it convenient to report the apparent extraction, i.e., the extraction indicated by comparing the value of the roasted ore, minus soluble salts, with the value of the tailings. How many errors are thereby committed it is not necessary to point out.

Jan 1, 1895

By Robert Berggren

THE hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, t but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for con-ventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs. Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Wash-ington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned.

Jan 1, 1940

By Frederick Laist

IN the course of the past 75 years the treatment of copper ores has undergone the most profound changes. To a lesser degree, this is true of all the nonferrous metals, but the rapid increase in the demand for copper due to the phenomenal growth of the electrical industry, and the discovery of vast new ore deposits in Michigan, Montana and Arizona, provided an exceptional incentive for improvements in smelting practice and for large-scale operations. Because these must perforce be carried on in regions where labor was scarce and wages high, the need for mechanization and larger smelting units soon became apparent. At a later date the porphyry coppers were discovered, with ores so low in grade that enormous tonnages had to be treated daily if they were to be made to pay at all. In some instances these ores were associated with, or overlain by, oxidized ores, which could not be concentrated mechanically and, of course, could not be smelted directly. This led to the development of the copper-leaching process. While the principles of the various smelting and leaching processes are for the most part of European origin, and have long been known, modern practice is essentially American and was evolved on this side of the Atlantic. The ores of copper may be divided into three general classes; viz, native copper, sulphide and oxidized ores. By far the greater number of commercially important ore deposits come under the classification of sulphides. Commercial deposits of native copper are limited to the Lake Superior

Jan 1, 1947

Application of technology to the search for new deposits went on apace in 1963. Traditional methods, aided by modern communications, were successful in some out-of-the way corners of the world that had not been adequately prospected, but the co-ordination of several mutually supporting techniques is necessary to define exploration targets in most areas today. Although these obviously include geophysics and geochemistry, which are treated elsewhere in this issue, geology continues to play a major role. As the search focuses on less and less obvious targets there will be more need than ever to "pull out all the stops." Any anomaly may have significance and must be evaluated as a possible lead. Ability to detect them increases as the laboratory workers refine techniques for measuring physical, chemical, and isotopic properties; it will be increasingly the responsibility of the exploration geologist to understand and apply these to economic problems. Simple propecting, the search for outcrops of recognizable ores of traditional types, was perhaps most successful for iron. Potentially large deposits of high-grade magnetite-specularite-hematite ore have been found in the Mary River area near the north end of Baffin Island. The ore holds up four hills that stand some 1500 ft above the surrounding country; obviously they were ripe for discovery by the first person to come across them, in this case Murray Watts, president of British Ungava Explorations, Ltd, As preliminary examination indicates a lump ore averaging 68 to 70% iron, these deposits may be commercial in spite of the unfavorable climate and their isolation from world markets.

Jan 2, 1964

By Matti J. Saarivirta

The relative machinabilities of the precipitation-hardenable Cu-0.9 pct Cr, Cu-0.25 pct Zr, and Cu-0.9 pct Cr-0.25 pct Zr alloys are improved from 18 to 80 pct by 0.75 to 1.25 pct Pb. The Lead also improves the tensile strength, hardness, ad resistance to softening of the Cu-Cr and Cu-Cr-Zr alloys. When the alloy containing 0.7 to 2.2 pct Cr, 0.10 to 0.25 pct Zr, 0.75 to 1.25 pct Pb, and balance copper is solution-annealed at 1000°C (1830°F) and then aged at 525°C (Y75°F), tensile strength of 65,000 psi, 16 pct elongation, 62Rb hardness, and 84 to 87pct IACS electrical conductivity are obtained. The copper base Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys have high electrical and thermal conductivities, high strength and resistance to softening at elevated temperatures, but their machinability is poor, i.e., close to that of the pure copper. In the manufacture of various components such as welding electrodes or electrical and thermal conductors it is ofter desirable that the alloy have good machinability for high production rates and long tool life. Thus, alloys that combine these properties may be used not only for existing applications, but for new ones where good machinability is a requirement. This investigation was undertaken to improve machinability without impairing other desirable characteristics of the Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys. These commercial alloys contain about 0.4 to 1.2 pct Cr, 0.10 to 0.25 pct Zr, and balance copper. Lead was selected as an element that should improve the machinability and possibly other characteristics of the alloy. WORK PROCEDURE This investigation began with a study of the effect of lead on the hardness, tensile strength, electrical conductivity, and machinability of the binary alloy containing 0.10 to 1.30 pct Cr and balance copper. This was followed by an investigation of the effect of lead on the Cu-0.1 to 0.4 pct Zr and Cu-Cr-Zr alloys. The alloys were made from initially oxygen-free copper and for comparison some castings were made from phosphorus-deoxidized Lake Copper. Commercially pure chromium, zirconium, and lead were used for alloying. In melting the chromium was added to molten copper at 1400°C (2550°F), the heat held for 15 min at temperature, and the temperature then lowered to 1350°C (2460°F) when the other elements were added. The alloys were held for 15 min at this temperature and cast into a cast-iron mold. One-kilogram, 3-in.-diam castings were made. An argon cover was maintained during melting and casting to prevent oxidation. The chemical compositions of the alloys are shown in Table I. The micro structure and properties of the alloys were studied in the cast and wrought conditions prior to and after various solution-annealing and heat-treating cycles. The relative machinability was determined as a function of the lead content and compared with the free-machining Cu-lpct Pb alloy. To determine the machinability, 13/16-in.-diam cast specimens were cut by a machine hack saw using a constant cutting speed of 50 fpm, a fixed feed force, and a new blade for each alloy specimen. Molybdenum highspeed steel saw blades, 0.032 in. thick with 14 teeth per in., were used in all tests. No cutting fluid was used. Five tests were made on each specimen and the average elapsed time per test was taken as a measure of the relative machinability for that alloy. The variation of cutting time for each alloy was less than 110 pct.

Jan 1, 1969