Search Documents

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By P. G. Shewmon, F. R. Winslow

An experimental method is describedfor Ihe determination of the derivative of the surface free energy (y,) with surface orientation using symmetric bicrystals. The method measures the equilibrium root-angle of grain boundary grooves for the same grain boundary on two different surfaces. In contrast to previous methods, the presence of annealing twins is not necessary. Results on silver at 900°C indicate that ??s/?3 is 0.014y, on the (loo), 0.075y, on the (111), and < 0.004?s on the (110). DURING an investigation of the kinetics of grain-boundary grooving on silver&apos; values of the derivative of the surface free energy ?s with respect to orientation were needed. Previous investigations of these so-called torque terms show that, for low-index planes in copper2 and nickel,&apos; a finite derivative exists even near the melting point. These two studies give the only previously published values of the torque on low-index metal surfaces. These investigators measured the equilibrium root angles, both greater than and less than 180 deg, along the lines where a twin boundary intersects a free surface. The technique described here is suitable for materials which do not have annealing twins, and enables the surface for study to be chosen instead of having to work in a direction normal to the twin trace on the surface. The purpose of this paper is to describe this new technique and to report the values found for the (111): (100), and (110) surfaces of silver. To check the technique proposed above, a series of 99.99 pct Ag bicrystals were used. These bicrystals were grown from the melt by a modified Bridge-man technique so that a low-index direction was parallel to the growth direction. Two orthogonal faces were studied on each bicrystal. One of these contained the low index or simple plane normal to

Jan 1, 1963

By L. D. Jaffe, F. W. Cotter, E. Cordon

The hardenability of titanium-base alloys was studied by metallographic examination and hardness survey of Jominy specimens end-quenched from the B range. Analyses of the data led to the equation log J = -0.57 + 0.25 @ct Fe + pct Mn + pct Mo) + 0.19 @ct Cr) +0.16 @ct V) + 0.03 @ct Zr). Here J is the distance, in sixteenths of an inch, from the quenched end of a Jominy hardenability specimen in the position of peak hardness, for material quenched from the B range. This equation fitted the experimental data with a standard deviation of approximately 0.29. The effects of the elements Al, Sn, W, Cu, Ni, B, C, N, 0, and H, and of pain size, were not statistically significant or not practically significant. A check against hardenability measurements in the literature showed agreement within the stated standard deviation. The equation should be useful in estimating hardenability of new or modified titanium alloys. HARDENABILITY in a titanium-base alloy is the ability of the alloy to retain the B structure on quenching. An alloy with high hardenability will retain the /3 structure even when cooled relatively slowly from a temperature at which B or P plus a is stable. A low hardenability material will retain P only if quenched extremely rapidly from the range of p or 0-plus-a stability, or will not retain it at all, at room temperature. High hardenability is desirable in titanium alloys to be heat-treated to high-strength levels. Its value is by no means limited to large section sizes. With high hardenability, a material can be solution-treated and cooled at a variety of rates, either to give high strength directly or, more generally, to give a soft ductile condition from which high strength can be obtained by subsequent aging. With low hardenability, high strength can be obtained, if at all, only by very rapid quenching, and there will generally be little increase in hardness on subsequent aging; an alloy of this type is limited in its applicability. On the other hand, alloys of very low hardenability have some advantages in weldability; essentially, they are always in the annealed condition, after welding as well as before. For commercial alloys, hardenability data are usually available, in the form either of property data after cooling from the solution temperature at various rates, with or without subsequent aging, or of results of a standard hardenability test, such as that originally developed for steels by Jominy and Boegehold.&apos; When modifications of an available alloy are considered, or preparation of new alloy compositions, it would be Very convenient to be able to estimate the hardenability of the new material without having to make and test it. A method of estimating hardenability of titanium alloys from their composition was suggested by one of the authors some time ago, on a preliminary basis, utilizing scattered data found in the literature.&apos; It seemed worthwhile to carry out a systematic experimental study of the effect of composition upon hardenability. EXPERIMENTAL PROCEDURE Approximately fifty heats of various compositions, weighing 8 to 10 Ib apiece, were melted in a small inert-gas tungsten-arc furnace with water-cooled copper walls. The starting material was 110 Brine11 titanium sponge, with high-purity metals added for alloying. Each heat was bottom-poured under vacuum through a molybdenum burnout strip into a cold graphite mold, to form an ingot approximately 4-1/2 by 3-1/2 by 3 in.* From each ingot were cut *The material was melted and cast by Pitman-Dunn Laboratory, Frankford Arsenal, to whom the authors must express their thanks. two pieces 4-1/2 by 1-1/2 by 1-1/2 in. These were forged, at temperatures adjusted to the composition, into 1-1/4-in. rounds, from which standard 1-in.-diam hardenability specimens3 were machined. A number of small samples were also prepared from forged materials of each heat, annealed, quenched from various temperatures, and examined metallographically. The P-transus temperature was determined by observation of the degree of resolution of primary a in these pieces. samples for chemical analyses were also taken from the forgings. One hardenability specimen of each heat was solution-treated for 1 hr approximately 50°F above the measured transus temperature, and the other for 1 hr approximately 250°F above the transus. (An additional hour was allowed for the specimens to reach furnace temperature.) These are not necessarily the temperatures that would be selected for

Jan 1, 1964

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By C. R. Austin

IN a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreas-ing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any, endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test has also shown promise as providing a "merit index" of high-temperature serviceability.2 Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350° C. (and a maximum of

Jan 1, 1934

The Raymond Memorial Volume, which the Members of the In-stitute have been so anxiously awaiting since the beloved man&apos;s death, is nearly ready for publication. It will contain about 45,000 words and some illustrations and a frontispiece portrait. This book promises to fill every expectation of the contributors to the volume and the host of admirers of the genius who so long guided the destiny of the Institute. It will contain one of Doctor Raymond&apos;s best stories, entitled "James and Jim;" his famous article on "Job on Mining;" and one of his poems entitled "The Grand Canyon." A biography of Doctor Raymond has been written by his daughter, who is the wife of a member of the Institute. The memorial addresses delivered by Dr. Henry F. Drinker and T. A. Rickard at the annual meeting in New York in 1919 will be included. There will also be very interesting reminiscences by H. M. Howe, A. S. Dwight, C. W. Goodale, R. W. Hunt, Lyman Abbott, J. F. hemp, T. A. Rickard. The volume has been edited by T. A. Rickard, which promises all that can be wished for the volume from a literary standpoint. The edition will he limited so that it is very desirable that orders for this volume be sent in to the Institute as promptly as possible. The price will be $5.00.

Jan 12, 1919

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By Anthony J. Chasteen

Although geothermal energy has been used by mankind for thousands of years and has even been used to generate electricity since the turn of the century, it is only in the last few years that the threatened energy crisis has focused attention on this resource. Geothermal exploration and development is being carried out in at least thirty-five countries on five continents. The status of geothermal energy production, however, is rudimentary with about 800 MW installed generating capacity worldwide, equal to about 0.1% of the world&apos;s total energy production.&apos; The world&apos;s first (1904) commercial generating site at Lardarello, Italy, will soon be surpassed by developments at The Geysers, Calif. There are other successfully operating geothermal power projects in New Zealand, Japan, USSR, Mexico and Iceland with pilot plants planned or under construction in Chile, El Salvador, Nicaragua, Turkey and the Philippines. The preponderance of exploration and development is being sponsored or assisted by individual governments, by the UN or by the U.S. Agency for International Development

Jan 10, 1972

Sifto Salt Div. of Domtar Chemicals Ltd. has developed a new method for installing roof bolts in the high backs of its 1-million-tpy rock-salt mine at Goderich, Ontario, on the east shore of Lake Huron. The method teams a telescoping- boom hydraulic crane with a specially developed combination auger-drill and bolt-tightening ma- chine. One man, controlling all operations from a basket supported at the end of the crane&apos;s telescoping boom, installs an average of 100 5-ft roof bolts per shift, at heights to 45 ft. The mine has very long backs that are not as stable as might be expected. The result has been that roof scaling has occupied an unusually high percentage of the underground work force. About six years ago, company officials decided to go to 100% roof bolting of all backs as a safety measure. The present roof-bolting equipment is the result of a development program instituted at that time to find a faster and more economical method for doing the job.

Jan 9, 1967

By Robert Glass Cleland

THE THIRD and most important item on the Phelps Dodge agenda for the development of new ore supplies involved the site of the company&apos;s initial venture into Arizona, the old mining camp of Morenci. By the purchase of the Arizona Copper Company&apos;s holdings in 1921, Phelps Dodge had obtained control of virtually the entire Morenci district, including town, public utilities, and, above all, the huge mineralized area that had once been divided between numerous competing companies. Because of this rigid concentration of ownership in the hands of one organization, Phelps Dodge was able to plan and successfully carry out a program of greater magnitude than any Arizona mining company had previously under- taken. The immense deposit of low-grade ore, usually referred to as the Clay Orebody, had been known to the mining companies of Morenci for many years. Pioneer exploratory work, both by the Arizona Copper Company and later by Phelps Dodge, revealed that the deposit, mostly of light-gray porphyry rock, lay under a hard capping from two hundred to five hundred feet thick. An intensive drilling

Jan 1, 1952

By Richard L. Ash, J. H. Kelley, W. H. McCracken, William Bellano, J. D. Morgan, D. R. Mitchell

Rubber-tired shuttle cars are finding increased use as gathering units in under-ground mines. As the name implies, they shuttle back and forth between the loading machine and the section transportation system. In many mines their use has in-creased the efficiency of the loading and gathering operations, resulting in increased output per man employed and decreased costs per ton. A car motivated by cable reel is shown in Fig I, and a car with battery power in Fig 2. A brief chronological account of the development of rubber-tired haulage equip-ment follows: 1936. J. H. Fletcher1 installed his first unit for the Blue Bird Coal Co., Carrier Mills, Illinois. This unit consisted of a battery-powered industrial tractor and a trailer with drop-bottom doors. The coal was transported for short distances to a hopper for discharge into mine cars. 1938. A battery-powered self-contained shut-tle car with rubber-tired wheels was built by the Joy Manufacturing Co. Two units were installed for the Katherine Coal Co., Lumberport, West Virginia. The shuttle car consisted of a materials-receiving body with a conveyor in the bottom to move the coal forward during loading and to unload the coal at the discharge station. 1938. A cable-powered shuttle car with four-wheel drive and four-wheel steer was developed by A. L. Lee. Special wheels mounted on king pins on the car permitted all four wheels to be steered. The cable reel was driven by a torque motor to give the cable proper tension during the payout and uniform tension when rewound on the reel. 1940. A Joy shuttle car equipped with trolley poles and a cable reel was developed to operate on a double trolley-wire system.2 This unit was installed at a potash mine of the International Minerals and Chemicals Corporation at Carlsbad, New Mexico. It is believed to have been the first installation of its kind, and the first of shuttle cars for handling material other than coal. 1941. Truck haulage3 was introduced in the Tri State District by the Eagle-Picher Mining and Smelting Company. Storage battery electric trucks were rebuilt to handle a bottom-dump trailer. 1941—Joy shuttle cars were installed in a mine of the United States Gypsum Company, Oakfield, New York. 1943—Joy shuttle cars were installed in several bauxite mines.4,5 1945—Joy shuttle cars installed in a lime-stone mine. Because of the nature of bituminous coal beds trackless equipment has had its greatest application in bituminous coal mining. Usually a shuttle car is filled by a continuous type of loader. In Fig 3 is shown a continuous machine loading coal into a battery-powered shuttle car, 48-in. coal. However, intermittent types of load-

Jan 1, 1949

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By W. A. Tiller

The unidirectional freezing of a semiinfinite liquid from one end has been treated by calculating the solute and temperature distributions in the liquid and solid phases with time, when the solid-liquid interface advances at a rate proportional to (time)lt2. The nucleation probability for new grain formation is calculated as a function of the constitutional and thermal properties of the alloy, the pouring conditions and the catalytic efficiency of the nucleating agents. The transition from columnar crystal formation to equiaxed crystal formation is assumed to occur at a critical nucleation frequency for a particular alloy and the quantitative dependence of the ratio (columnar zone length/equiaxed zone length) upon the freezing conditions has been predicted. The effects of (i) fluid flow in the liquid, (ii) heat transfer through a mold wall, and (iii) a finite ingot length, have been explicitly tveated as departures from ideality. These departures from ideality are found to have very important consequences on the ingot stmcture. In Part I&apos; of this series, a qualitative description of the general ingot structure was developed. The factors that determine i) the ratio of the equiaxed zone length to columnar zone length and ii) the grain sizes in these zones, were discussed. In the present paper, topic (i) will be treated quantitatively, and it is intended that topic (ii) will be treated quantitatively in Part 111. The complete treatment has been split in this manner for ease of development and coherency of presentation. The treatments are quite mathematical in nature and, although some of the conclusions to Part 11 depend upon the treatment presented in Part 111, it was felt that the intended audience would find the material more readable and more useful in its present form. To this same end, it seems worthwhile to reiterate some of the qualitative aspects of grain nucleation during ingot solidification before embarking on the mathematical description. QUALITATIVE ANALYSIS In the conventional method of casting, a liquid alloy with a certain degree of superheat is poured into a mold. The outer rim of liquid metal cools rapidly to the liquidus temperature of the alloy and begins to undercool. As the degree of undercooling increases, nuclei of solid begin to form in this chill layer, this nucleation being catalyzed by certain heterogeneous particles in the liquid. The grains in the chill layer which are generally of random orientation, begin to grow inwards because of heat conduction through the mold. The grains usually develop a columnar shape since the frequency of nucleation of new grains in the liquid ahead of the advancing interface is generally insufficient to seriously impede the growth of the original grains. Due to the slow diffusion rate of solute in the liquid, a solute distribution is formed in the liquid adjacent to the interface which is either an excess or a depletion if the partition coefficient, ko, of the solute is < 1 or > 1, respectively. Thus, the liquidus temperature of the liquid adjacent to the interface is a function of position. The actual temperature in the liquid is also a function of position and the temperature gradient at the interface decreases as the interface moves away from the mold wall. Since the rate of advance of the interface decreases with time, the equilibrium temperature distributions and the actual temperature distributions as a function of interface position, X, can be illustrated as in Fig. 1. Thus, a region of liquid may exist in which the actual temperature is below the liquidus temperature. This liquid is contitutionally supercooled and therefore unstable with respect to the nucleation of new grains. Now, since the supercooling in Fig. 1 increases as the interface moves further away from the mold wall, the nucleation rate of new grains will increase. When the nuclea-

Jan 1, 1962

By AIME AIME

[The American Institute of -Mining Engineers does not assume responsibility for any statement of fact or opinion advanced in its papers or discussions.] A detailed list of the&apos; papers contained in this section is given in the Table of Contents, pages i. and ii. Comments or criticisms upon all papers given in this section whether private corrections of typographical or other errors or communications for publication as "Discussions," or independent papers on the same or a related subject, are earnestly invited. ERRATA. The following corrections and. additions to papers contained in Bi-Monthly Bulletin No. 7, January, 1906,-were received too late for incorporation in the text of said papers ; but will be introduced in their: proper places: in the volume of the Transactions: These corrections are here published in order to bring them -promptly to the notice of the Institute. Page Line Cover, title-page and at the top of pages in the preliminary section "No. 1 " should be "No. 7 ". 1. Bottom For :" Dr. P. H. Shimer" read "Dr. P. W. Shinier " 69. Fig. 3. "N" of compass-record should be ?S". A new block for this illustration has been made as shown on p. xxxviii of this Bulletin. 78. 3 from bottom. For " slope " read " stope." 89. Fig. 2, small diagram in upper left-hand corner. Omit use 50 ft. to 1" scale ". For "Thro&apos; 250 " read " Thro&apos; 200 ". Add dotted line extend¬ing from upper right-hand corner of the square

Mar 1, 1906

NEW YORK SECTION Executive Committee DAVID H. BROWN, Chairman JOHN H. JANEWAY, Vice-Chairman F E. PIERCE, Secretary, 35 Nassau St., New. York, N. Y. P. A. MOSMAN, Treasurer LEWIS W. FRANCIS BENJAMIN B. LAWRENCE At the meeting of the New York Section held at the Machinery Club on Dec. 8. 1915, the subject was "The Engineer in Modern Warfare, with Especial Reference to the Present European Conflict." Dr. Henry S. Drinker, who is Chairman of the Institute committee on the Engineer&apos;s Reserve Corps movement, opened the evenings&apos; talk with a short statement of the aims and advantages of the Students&apos; summer military camps, fostered by the Society of the National Reserve Corps, he being a member of the Advisory Committee of University Presidents. The speakers of the evening were Col. William M. Black and Col. John Biddle, both of the Corps of Engineers, U. S. Army. Col. Black is the

Jan 1, 1916

By Thomas Bannon

PROSPECTING for oil in Spain has been going on for many years but only in a very haphazard way and without adequate geological or technical advice. Shallow wells have been drilled in several provinces but, for the most part, they have been doomed to failure from the beginning because of unfavorable geological locations, inadequate drilling equipment inexperienced operators, or lack of sufficient capital. Geologists seem to agree that the most favorable chances for commercial fields are in the northern part of Spain where the petroliferous Triassic beds underlie Cretaceous and Tertiary sediments. The prov-vinces of Santander, Burgos, Alava, Vizcaya, Navarra, and Guipuzcoa seem to offer the most promising localities. Several shallow wells have been drilled near Villamartin about 60 Km. northeast of Cadiz. One of these wells produced a small quantity of light oil but was never operated. The Spanish Government has been drilling on a well in this district for some time, using the Russian free-fall drilling system. The present depth is about 3000 meters. Several years ago the Compania Petrolera Franco-Espanola drilled a well to a depth of about 700 meters near Elorrio, province of Vizcaya. A diamond-core drill was used. The well was located on vertical Cretaceous beds near an igneous dike. The same company, in March, 1923, made a new location about 500 meters away from the first well and the same distance from the dike, in beds dipping about 80°, and is now drilling its No. 2 well. The last depth reported was about 200 meters.

Jan 3, 1924

By C. L. Warwick, A. B. Parsons

The papers and discussion appearing in this volume were presented at a symposium jointly sponsored by the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers and held at Philadelphia, Pa., November 29, 30, and December 1, 1944. Late in January, 1944, Lieut. Col. C. H. Greenall, Officer-in-Charge of the Laboratory Division, Frankford Arsenal, Ordnance Department, U.S.A., suggested to the American Society for Testing Materials that it might be a propitious time to arrange for a symposium on stress-corrosion cracking at the Annual Meeting of the Society in June, and agreed to make available a number of papers relating to work being carried out at that Arsenal. The Society&apos;s Committee B-5 on Copper and Copper Alloys, Cast and Wrought expressed keen interest in the symposium, and other Society committees were contacted and agreed to cooperate. Since the subject is one of primary interest also to the American Institute of Mining and Metallurgical Engineers, it was arranged that the two organizations would jointly sponsor the symposium. A Symposium Committee was formed under the joint leadership, for A.S.T.M., of Carter S. Cole, then Chief of the Metals Branch, Conservation Division, War Production Board and now Engineer on the Headquarters Staff of the Society; and, for A.I.M.E., of E. A. Anderson, Chief of Metals Section, Research Division, New Jersey Zinc Co. (of Pa.) and chairman of the Program Committee of the Institute of Metals Division. The Symposium Committee was constituted as follows:

Jan 1, 1945

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By R. G. Wheeler, J. W. Goffard

The Larson-Miller parameter was used to correlate time, temperature, and indentation creep of magnesium, aluminum, and some of their alloys. In the temperature range 300" to 450°C, the short-time Meyer hardness of pure magnesium was less than that of the magnesium alloys tested, but for long times the pure magnesium has greater indentation creep resistance. Aluminum (1100 alloy) had 1.5 to 2.5 times more indentation creep resistance than magnesium at 300" and 450oC, respectively. Hardening of aluminum with a dispersion of Al2O3 was effective in the time and temperature ranges studied. New technologies have required the development of new materials and the utilization of the more familiar materials for new and unusual applications. The use of magnesium and aluminum and some of their alloys, because of their desirable nuclear characteristics, light weight, low cost, and ready availability, has been extended to the 300" to 450°C temperature range. In this temperature range the basic consideration of these materials must be their rate of plastic flow rather than offset yield strengths. The indentation testing reported here arose from a need for design data for the load-holding ability of supports made of these materials. Test Procedure—Hardness indents were made with a 0.275-in.-diam quartz indentor and a 10.65-lb load. The indentor was made by fire-polishing a spherical surface on the end of a fused quartz rod. The samples were held at temperature in a graphite crucible controlled to ±2°C. A thermocouple was attached to the sample and test temperatures were recorded. The diameter of the spherical indentation was measured at the end of a test period and the compression stress (Meyer Hardness) was determined by: H___________load__________ m = projected area of indent Samples were 1 in. in diam and at least 1/4 in. thick. It was observed that at the higher temperatures and longer times, the quartz indentor would stick to the magnesium sample. The quartz indentor was, therefore, frequently inspected and fire-polishing repeated when necessary. The area of sticking was always a small fraction of the area of indent and was therefore considered to have an insignificant effect on results. Correlation of Hot-Indentation Test Data with Time-Temperature Parameter—Sherby and Dorn&apos; have correlated creep or tensile data of a&apos; solid solutions of aluminum with a temperature and strain-rate parameter suggested by Zener and Holloman. underwood2 used this parameter to correlate creep properties of some steels with hot hardness, and upon the basis of this correlation a means of obtaining creep properties from short-time (and inexpensive) hot hardness tests has been demonstrated. Since the validity of the correlation of creep properties with a time-temperature parameter and the correlation of creep properties with hot hardness have been shown, it follows that hot hardness may correlate with the time-temperature parameter. The hot-indentation data obtained was expressed as Meyer hardness, and was shown to be time and temperature dependent. Correlation of Meyer hardness, time, and temperature with the parameter was made using the relationship: Hm = Meyer hardness t = time, hours T = absolute temperature, OK K = constant A value for the constant K was calculated by equating In l/t + K/T at different temperatures and times but at the same hardness. The correlation was tested by plotting Hm vs the parameter, In 1/t +K/T. Since materials are being sought which have high hardness at low indentation creep, i.e., a high Meyer hardness for long time at high temperatures, low values of the parameter are ofthe most interest. TEST RESULTS Magnesium—Pure magnesium (99.98 pct) cut from extruded rod was indentation tested perpendicular to the rod axis at temperatures of 300°, 350°, 400°, and 450°C for times ranging from 6 sec to 112 hr. Fig. 1 shows the time dependency of Meyer hardness at the four constant temperatures. Fig. 2 shows the correlation of the Meyer hardness of pure magnesium with the time-temperature parameter using a K of 22,720 in Eq. [I]. At the bottom of Fig. 2, the effect of doubling the time of indentation t2 = 2(t1), on the abscissa for any time is shown graphically. This effect is of constant magnitude. Also shown graphically are the magnitudes of the effects on the

Jan 1, 1960