Search Documents

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By E. P. Jennings

Large deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archæan schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-cleposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained.

Jan 1, 1913

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By John R. Low

A number of cases of low-temperature, intergranu2ar brittle fracture of metals containing small amounts of certain impurities, have now been identified. Some degree of understanding of this phenomenon exists for the simpler binary systems of a metal and a single impurity, but the profound effects of other impurities and alloying elements in modifying this type of behavior remain unexplained. Current research in this area is reviewed and some of the newer techniques of investigation which should make possible a more quantitative study of the structure and composition of grain boundaries in impure metals are described. To indicate the subject matter of this lecture, we may begin by reviewing the experimental observations concerning low-temperature intergranular brittleness in impure metals, particularly those examples in which the embrittlement appears to result from what has been called "equilibrium grain boundary segregation."' These are the systems in which it has been impossible, at least up to now, to detect the presence of any second phase film at the brittle interfaces. When second phase films are present they are usually readily detectable by fractographic methods, often appearing as epitaxial films in geometric or dendritic patterns. An example is shown in Fig. 1 for the case grain boundary carbides in a sensitized stainless steel which failed by intergranular brittle fracture at 78?k2 In contrast to this type of embrittlement there are numerous examples of low-temperature intergranular embrittlement in which the fractographs are essentially featureless, for example, that of an oxygen-embrittled iron shown in Fig. 2. The only second phase particles visible are the small, widely separated, round oxide particles typical of the bulk material. The fracture surface is extremely smooth and the fracture path appears to follow the intergranular interface without deviation. This type of fractograph also implies that crack propagation has occurred without plastic deformation at the crack tip, since localized slip or twinning ahead of the crack would be expected to distort the interface and be readily visible in the fractograph. Such indications are occasionally seen in these fractographs, but are not characteristic. A second example of this type of fractograph is shown in Fig. 3, which is from a temper-embrittled, carbon-free, Fe-Cr-Ni alloy containing Sb, broken at 1OO?C.3 The similarity to the oxygen embrittled iron case will be apparent. In the case of the temper embrittled Cr-Ni ferrite containing antimony, it is possible to remove the embrittlement by suitable thermal treatment. The grain boundaries may then be examined by thin film transmission in the electron microscope for the material in both the nonembrittled condition and in the embrittled condition. Two boundaries are shown in dark-field transmission in Fig. 4, one in the nonembrittled

Jan 1, 1970

By M. J. Sinnot, J. C. Shyne

Low-frequency mechanical damping measurements were made to investigate internal friction in Fe-A1 alloys. The atomic ordering of the Fe-A1 system strongly influenced the stress-induced ordering internal friction. Magnetoelastic damping was also encounteyed and was shown to be reduced by the application of a static stress. THIS paper describes some damping experiments made on alloys of Fe and Al. Stress-induced ordering internal friction was measured with samples containing from 9.8 to 31.3 at. pct Al. Aluminum is soluble in a-Fe to about 50 at. pct and forms at least two long-range ordered structures, Fe3Al and Feu.' Stress-induced ordering internal friction is known to occur in many substitutional solid solutions, but few measurements of this damping effect have been made with alloy systems that have pronounced ordering tendencies. LeClair and Lomer developed expressions relating the relaxation strength of the damping process to the degree of atomic ordering and predicted that stress-induced ordering internal friction would be zero with complete ordering.' This concept was confirmed experimentally by Lulay and Wert using the system cd-Mg It is also consistent with the weak stress-induced ordering peaks observed in P -brass by Artman and in 16 wt pct Al Fe-Al by bert.' It was expected, therefore that the ordering characteristics of the system Fe-Al would strongly influence the stress-induced ordering internal friction exhibited by the experimental alloys. SAMPLE PREPARATION The alloys used in this investigation were induction melted under vacuum using high-purity melting stock. The iron was electrolytically refined Plastiron 101 which contained 99.85 wt pct Fe. The aluminum was a special 99.95 pct pure grade supplied by Alcoa. The only other raw material was spectrographically pure graphite which was used in small quantities as a deoxidant. The amount of carbon used was slightly in excess of the amount required to completely deoxidize the melt; this resulted in residual carbon contents of 0.01 to 0.02 pct in the finished alloys. The vacuum cast 2 1/2-in. diam ingots were hot rolled to 5/8-in. diam round bars. Portions of these bars were hot swaged and hot drawn to 0.050-in. diam wire. Straight pieces of the hot drawn wire were slowly heated to a temperature of 1300°C in a He atmosphere. After holding for 4 hr, the samples were allowed to cool in the furnace. This annealing treatment resulted in grain growth in the samples, the final grain size being about the same as the wire diameter. The grain boundaries were oriented perpendicularly to the wire axis, giving a bamboo grain structure. The existence of a preferred orientation could not be detected in these coarse grained samples. If the samples had a fiber structure, this probably would have been the same in all samples because of similar processing, thus the influence of crystal orientation on the relaxation strength would have been similar in all samples. The aluminum contents of the alloys are listed in Table I. EQUIPMENT The principle of the torsion pendulum was used for the internal friction measuring device. The

Jan 1, 1961

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

INTRODUCTION The after-tax rate of return that properly discounts future cash flows is usually referred to as the "discounted cash flow-rate of return" (DCF-ROR). The method is also referred to as the internal rate of return, true rate of return, and investor's rate of return in some literature. According to Stermole (1974, p. 188) industry polls indicate that the DCF- ROR method is the number one economic evaluation decision method used by more than 90% of the industrial companies that use for- mal economic evaluation procedures. Other economic evaluation methods that have been used in the past, such as payback period, accounting ROR, etc., have largely given way to DCF-ROR analysis because they fail to account properly for the time value of money. DCF-ROR is generally defined as that rate of return that makes the present worth of future generated cash flow over the life of the project (including after tax salvage value) equal to the present worth of all after-tax investments. The "present worthing" of future cash flow involves discounting future cash flow to a present value according to the mathematics of compound interest at some interest rate. The determination of the interest rate that equates the present worth of future after-tax earnings with the present worth of all after-tax investments necessary to create such earnings is properly called the discounted cash flow rate of return analysis. Although present worth calculations are usually used for determining the DCF-ROR, the same results can be obtained by comparing income and costs of any equivalent point in time, i.e., future worth, etc.

Jan 1, 1980

By M. Stern, I. S. Servi, W. W. Webb

ZINC has been considered an ideal material for investigations of the behavior of dislocation walls in metals. It has appeared particularly useful for studies of the mechanisms of plastic deformation and the motion of low-angle boundaries under stress, because orientated crystals are easily grown and cleaved. Moreover, the hexagonal structure makes the introduction of controlled tilt boundaries relatively simple. Apparently, another of the many reasons for selecting zinc as a working material is its commercial availability at the 99.999' pct purity level. However, most elements are only slightly sol-

Jan 1, 1959

The key-note of good writing, as of good manners, is B natural. Sincerity is the first requisite for effective writing. When a man says what he knows or believes, he is likely to be interesting, because each human being possesses an individuality, a point of view, or a range of sympathy that makes him different from his fellows. To say or to write what you do not think, for the mere sake of talking or writing, is a verbal exercise that must be performed with extraordinary skill if it is to be attractive. Affectations are rarely attractive, rarely effective. To be natural is to be yourself, not a poseur; to give the reader the best of yourself, instead of re-warming the baked meats of yesterday. Quotations-which are second-hand thoughts-will serve occasionally when the thing you want to say has been said so well by another that it would be waste of energy to try to say it better; gut, as a rule, the utterance of the writer himself is more interesting than the quotation, because the writer brings something of himself to bear on the subject, and for the moment is more in touch with the reader than any dear departed author. Therefore, say things as best you can in your own way, neither in borrowed words nor in the phraseology that mimics another. Write as if you were speaking to a person whom you desire to persuade or convince. You will then write better than you speak, because, in the first place, you can be more deliberate, and, secondly, you can revise what you have written. Speaking and writing are similar mental acts, with a difference: the difference between eating food raw and eating it cooked. Some kinds of food gain nothing by being cooked; likewise some kinds of utterance are not bettered by being written down first; but most expressions of thought, especially

Jan 1, 1931

By A. H. Willis

In this paper the results of an exploratory study conducted by personnel of the Knolls Atomic Power Laboratory on 18.6, 22, and 40 wt pct uranium-zirconium alloy will be presented. LARGE power output and long life or endurance from small, compact nuclear reactors require the use of enriched uranium for a fuel material. However, the ability to remove heat from the element, the tolerable fission product concentration, or some physical limitation of the system can limit the allowable fuel enrichment, or the volume of the fuel. In such an event, the fuel-element designer must find a suitable diluent for the uranium. Zirconium is an attractive material for such a purpose as it has good nuclear properties and a low absorption cross section. Because it has a good corrosion resistance in water, zirconium is a suitable cladding and the uranium-zirconium alloy makes a good core material. The alloy has a high thermal conductivity, a low elastic modulus, and a low thermal-expansion coefficient, all of which tend to minimize the thermal stresses in the core. Furthermore, the unirradiated material is reasonably ductile and has adequate strength. DESCRIPTION OF SAMPLES Two types of cylindrical samples were used in this study 1) short, 1/2-to 1-in.-long samples to test the irradiation stability of the alloy and 2) 2-ft-long samples to investigate the resistance of an element to longitudinal deformation. Composite samples having 0.060-to 0.140-in. core diameters and clad with a 0.010-in. thick zirconium jacket were fabricated by coextrusion and by hydrostatic pressure bonding of the cladding to the preformed core material. Both fabrication processes produced the uniform metallurgical core-to-cladding bond which was felt necessary to minimize the uncertainty of the central core temperature. Both consumable-arc and induction-melting techniques were used to melt the uranium-sponge zirconium core alloy. Since a graphite crucible was used in induction-melting this alloy contained more carbon impurity, which resulted in a finer grain size than the arc-melted alloy. The core to cladding interface was uniform in elements coextruded from the fine-grain, induction-melted core material, while those elements fabricated using arc-melted core material had very irregular interfaces because of the coarser grain size. Both cold-worked and heat-treated fuel materials were irradiation tested. Cold-worked alloys were swaged to about a 5 pct final reduction in area without subsequent annealing. The heat-treated alloys were heated to 800°C, held at temperature for 15 min and furnace-cooled to about room temperature. This

Jan 1, 1960

By T. D. Lynch, N. B. Pilling

The development of a proper treatment for shells in conncction with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of the liquid itself upon both. Without attempting an exhaustive citation of the literature, mention may be made of some of the more important contributions, notably the pioneer work of Le Chatelier,' followed by the extensive investigations

Jan 1, 1920

By Thomas Elliott

It is now clearly evident that 1963 is witnessing a record year for prospecting and exploration in British Columbia and Yukon Territory, as substantiated by the following facts: ? About 60 large mining companies and many smaller ones are active in the search for new ore deposits. ? More than 500 prospectors and exploration geologists have been in the field this season. ? It is estimated that $10 million has been spent this year on the search for new ore deposits. ? Claim staking in B. C. to July 31, totalling 14,250, is up 2000 over 1962. ? Helicopter companies report a record total of 25 aircraft chartered to mining groups, with additional numbers used in oil-gas exploration. ? Leading assayers state that business with the industry is double that of the previous year. ? Diamond drillers report an increase of approximately 25% in the amount of contracts now on hand. The question is often asked, "Why is mining so active in Canada's Pacific Northwest?"

Jan 12, 1963

On June 15, Dr. E. E. Southard gave the following report to the Advisory Committee on Industrial Mental Hygiene of the. Engineering Foundation. Psychiatric social work, a new specialty in social work, was the topic of several section meetings (500-600 in attendance) at the National Conference for Social Work, held at Atlantic City, June 1-6. The new specialty was stated, by Dr. R. C. Cabot, to be the greatest single advance in medical social work since its establishment. Reports from three schools (Smith, New York, Philadelphia) indicate a good production rate of personnel, probably at least one hundred a; year, chiefly to be absorbed by hospitals, unless industrial psychiatry steps into the field. No detailed public announcements concerning industrial psychiatry were made; but private discussions elicited approval only for the program. Indications are that many non-medical social workers will decide to get additional training to go into medical social work and then to specialize in psychiatric social work and that many medical social workers will desire to specialize in psychiatric social work, with a view partly to entering reconstruction work, partly to entering industrial psychiatry. Suggestion has been made that psychiatric social workers may go into some kinds of, employment management and may look for special courses to that end. Evidence. has been brought that certain "compensated" psychopathic employees have been good (even very good) workmen: emphasis should be laid on this point to show the constructive aspect of industrial psychiatry:

Jan 8, 1919

By JOHN MARKLE

JOHN MARBLE, mining engineer, coal operator, philanthropist, member of the Institute since 1879, vice-president in 1903-04, has been paid the well deserved tribute of Honorary Membership. The presentation of the diploma was made at a luncheon in New York on Feb. 13, the citation reading: "In recognition of his work as an engineer and administrator of mines and his services to mining engineering education." Within the last month Lafayette University dedicated the new John Markle Mining Engineering Building, the gift of the eminent alumnus for whom it is named. In addition, Mr. Markle has contributed a maintenance fund for the carrying out of far-reaching plans for improving the mining courses to be given at the Institution. One of his theories is that quality rather than quantity of engineering graduates is the need of the profession. John Markle was born in Hazleton, Pa., in 1858. He received his degree of M. E. at Lafayette in 1880, and married Mary Estelle Robinson in New York City in 1884. Since 1880 he has been associated continuously with the firm of G. B. Markle & Co., and its successor companies. He has also been an official of numerous other important companies, although he is now retired from active business life.

Jan 1, 1930

By C. T. Cox

W. A. Reich.*—I should like to ask Mr. Cox if he has any information on the change in

Jan 1, 1945

By B. Russell, J. R. Tuffley

The stability regions of the normal sulfate and the various basic sulfates of lead in 02-SO2 and PhS-SO2 gas atmospheres were calculated from available thermodynamic data over the temperature range 600o to 1200oC. Roasting experiments were carried out on samples of synthetic lead sulfide at various temperatures and for various roasting times. Compounds in the oxidized surface layers were identified by X-my techniques. The order in which the various reactions occurred was determined by considering the experimental results in conjunction with the thermodynamic calculations. The results of these investigations were applied to the sintering of lead sulfide concentrates, and the extent to which each of the various reactions occurred in a sinter bed was determined. PRODUCTS which may be formed during the roasting of PbS are PbS04, PbSO4. PbO, PbSO4 . 2PbO, PbSO4 . 4PbO, PbO, and Pb.1, 2 The formation of some sulfates has been studied by a number of investigators3-' whose experiments have mostly been confined to the temperature range between 500" and 850°C. Culver, Gray, and spooner3 were able to isolate the reactions which formed PbSO4 and PbSO4. PbO by carefully controlling the compositions of the roasting gases. The kinetics of these reactions were studied within the temperature range 673" to 807°C. Gardner4 and Merrick5 also studied the kinetics of oxidation of PbS. Gardner disregarded the existence of basic sulfates and, as a result, misinterpreted some of his experimental data. Merrick recognized that most of the products of oxidation were mixtures of basic sulfates, but was unable to identify the individual components. Hoschek6 oxidized PbS in air at temperatures up to 800°C. The products were analyzed after roasting had proceeded for some minutes, but no attempt was made to follow the reactions in the initial stages. Consequently, no roasting mechanism was derived. He also showed that PbSO4 and PbSO4 - 4PbO decomposed slowly in air at temperatures in the region of 800°C. The stability regions of sulfates in the temperature range 500" to 850°C have been only partially determined, while practically no information is available for higher temperatures. In the lead sintering process, PbS concentrates are roasted at temperatures within the range 1000o to 1200°C. In order to investigate sulfate formation, it is necessary to determine the effects of temperature and gas composition upon the various oxidation reactions and upon the regions of stability of the various lead sulfates. Kellogg and Basu2 introduced an equilibrium diagram similar to those in Figs. 1 to 3 which provides a convenient medium for represent-

Jan 1, 1964

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By Joseph Hays

MORE years ago than I care to admit I conferred the title of "combustion engineer? upon my-self since nobody else would confer it. I thought at the time, and for some, years thereafter, that my field was limited to the precincts where the fuel was being burned, but I found that I could stand in the door of the furnace room and hear distressed heat units calling for help all over the plant. Some of them were over-worked, others were compelled to do useless work, and still others, anxious to render a proper account of themselves, were not permitted to do any sort of work at all and were utterly wasted. The combustion engineer has something to do at that interesting occasion when the heat unit is being born in the furnace, but his responsibility does not end there. He must follow the little fellow throughout the entire period of its hectic existence in the plant and see that it gets a fair chance and a square deal everywhere. I fear that the general impression of the combustion engineer's duties is much as mine was in the beginning; that his job is limited to the implements and processes incident to the specific operation of converting fuel into active, heat energy and of applying it to the boiler, the still, or what-not, with the least possible waste. But is it not true that a heat unit saved in a remote corner of the plant means just as much to the fuel account as another saved at the furnace? And if nobody else is looking after the heat units out on the range why should the combustion engineer spend all of his time hanging around the corral? If combustion engineer is not a broad enough title to cover the man in charge of a general heat unit rescue campaign call him any-thing else you please. The job is all that counts. The name means nothing. A skunk by any other name would smell as bad. The greatest field I have ever found for general "heat rescue" work is the oil refinery. In refining we first put heat into the oil and then take it away from the vapor. The greatest heat losses occur during the cooling operation, but there are losses, many of them preventable, either wholly or partly, at every step of the several processes in oil refining.

Jan 3, 1928

THE following employment items are mode available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of, the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. POSITIONS OPEN Mining Engineer with some engineering training, capable of doing mapping, surveying, exploration, geology and transit work. Location, New York State. Y7333. Mineral Dressing Engineer, B.S. Mining or Chemical Engineering, age to 35. Must have knowledge of flotation. Duties will be in applied research and field evaluation of cationic and anionic flotation agents. Salary, $3500 to $7000 depending on experience. Location, Chicago. R-8971. Geological Draftsman, 25 to 30, with some experience in working with a geologist. Salary, $5100 a year. Location, New York, N. Y. Y7153.

Jan 1, 1952