Search Documents

By G. Y. Chin, M. T. Dolan, W. L. Mammel

The least work analysis of constrained deformation, first proposed by Taylor and recently modified by Chin, Hosford, and Mendorf to include twinning, has been applied to the problem of axisynmetric flow. Calculations were made, for the case of (111}(110) slip and {111}(112) twinning applicable to fcc deformation. The solutions were obtained by linear programming techniques and with the aid of computer methods. The results show that in axisymnzetric tension the onset of twinning tends to decrease the plastic strength anisotropy as compared with the case of defortnation by slip alone. In compression, however, the strength anisotropy is increased as a result of twinning. The [100] and 11111 orientations and their vicinity are unfavorable for twinning in tension and compression, respecticely. With slight modifications, the present results may be applied to bcc metals deform ing by {110}(111j slip and (112} (111) twinning. Implications of present results to wire texture development of low stacking fault energy fcc materials arc discussed. PREVIOUSLY we' have applied linear programming techniques to obtain solutions to Taylor's least work analysis2 of constrained deformation of single crystals undergoing axisymmetric flow, such as occurs in an axially loaded polycrystalline aggregate. These solutions yielded values of the parameter M = o/.r = Y/w which relates the external stress-strain (u-c) curve to the shear stress-shear strain (7-y) curve for the crystal. The value of M is dependent on crystal orientation and hence enters significantly in texture strengthening considerations.3'4 Recently the Taylor hypothesis was modified by Chin, Hosford, and Mendorf' to include mechanical twinning. The latter has now been applied to the problem of axisymmetric flow and the results are reported in this paper. Calculations have been made for {111 )( 110) slip and {111 )(112) twinning applicable to fcc crystals. With minor changes in the indices of the slip and twin systems, the present results are also applicable to bcc crystals which slip on (110) (111) and twin on {112)(111) systems.

Jan 1, 1970

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger's grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger' s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By W. B. HILLHOUSE

AN excerpt from the Alabama State Mining Law, pertaining to, transporting men' into and out of the mines, reads as follows: "A trip of empty cars may be operated for the purpose of taking employees into and out of the mine, where the distance to and from their work exceeds one mile." The State Mining Department of Alabama includes in its inspection the transportation of men into and out of the mines, also studying and noting improvements, or progress made, that would tend to create a greater assurance of safety in this practice. Everyone is familiar with the original safety methods employed in man-trip transportation, such as passing a rope around the trip of cars, or through the cars, fastened in the conventional manner, and with the usual "clog," commonly called a drag, on the rear end. Also there is a more advanced method of transporting men, such as the double-rope system, which is feasible on slopes used exclusively for this purpose, and is very satisfactory. However, for the past eighteen months; the Republic Steel Corp. and the Tennessee Coal, Iron & Railroad Co. have adopted a practice that shows

Jan 1, 1935

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

By James T. Gow, Oscar E. Harder, Anton de S. Brasunas

THIS paper deals with the results obtained and the techniques employed in determining: I. Liquidus and solidus temperatures of the HH and HT type heat-resistant alloys. † 2. The relation of true temperatures (thermocouple) to apparent temperatures (optical pyrometer) for the molten HH and HT type alloys. This work was the outgrowth of needing to know something definite about these temperatures in order to study the effect of pouring temperatures, shake-out times, and heat-treatments on the properties of some heat-resistant alloys. The information developed is thought to be of interest to industry for guidance in foundry practices and the industrial heat applications of the alloys. This paper is based upon work that has been done for the Alloy Casting Institute at Battelle Memorial Institute. LIQUIDUS AND SOLIDUS TEMPERATURES OF HH AND HT TYPE ALLOYS Experimental Procedures Temperature-time curves were obtained during the cooling and solidification of several HH and HT type alloys. The metal was melted in an Ajax high-frequency induction furnace and poured into a coresand mold for cooling. The temperature measurements were obtained by means of a platinum, platinumrhodium thermocouple contained within a fused silica sheath, which was extended through the side wall of the dry core-sand mold to a point at about the center of the mold cavity, which was 3 in. in diameter by 5 in. deep. The cold junction of the thermocouple was kept in an ice bottle, and the temperature was recorded automatically on a direct-reading potentiometer recorder. Through a switching arrangement, the temperature recorded was checked occasionally with a portable Leeds and Northrup potentiometer indicator. Less than a 5°F. variation in the two instruments was always found. This is within the limit of accuracy of readings. The thermocouple used was checked for accuracy against a standard couple, both before use on this work and after completion of the work, by the instrument laboratory. Temperature-time Cooling Curves Fig. I is an enlarged reproduction of a part of one of the cooling curves over the temperature range of 2600° to 2200°F. for an alloy of the HT type with 0.45 per cent carbon, 16 per cent chromium, and 36 per cent nickel. This is a typically shaped cooling curve as obtained for the alloys. It will be noted that two temperatures are shown on Fig. r for the liquidus temperature. It is thought likely that the higher temperature, A, at the point at

Jan 1, 1945

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958

By Eleanor Haslem, Carl A. Zapffe

THE present investigation has three principal purposes: I. To develop a method for measuring hydrogen embrittlement that avoids certain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. SELECTING A TEST METHOD Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. DEVELOPING A MACHINE FOR MEASURING HYDROGEN EMBRITTLEMENT As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1946

By Ottey M. Bishop, William G. Peryam, Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rocksurfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to [P]8.oo per ton, and from the property to San Fernando the rate is [P]16.00 per ton. The company pays the road toll, [P] 1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By C. G. Dunn

According to a recently suggested effect of silicon on the re recrystallization textures of high-purity Fe-Si alloys with (111)[112] type rolling textures, the recrystallization texture for a rolled (110)[001] oriented iron crystal probably should be entirely different from that of a (110)[001] oriented 3 pct Si-Fe crystal. Comparative studies of iron and 3 pct Si-Fe crystals, however, show that both have (110)[Ool] recrystallization textures when the rolling textures are the (111)[112] type after reductions in thickness of about 70 pct. Qualitatively the results from the iron crystal are like those of polycrystalline high-purity 3 pct Si-Fe and not like polycrys-talline high-purity iron. The large effect previously noted probably involves unknown impurities or processing variables rather than silicon itself. Some problems on experimental and analytical procedure for a spherical X-ray specimen, which was machined from a laminated composite of sheet specimens, are treated in the Appendix. A possible strong effect of silicon on the textures produced in cold-rolled high-purity Fe-Si (HPFe-Si) alloys during primary recrystallization and normal grain growth was suggested in a recent paper.' All the textures were far from the random-orientation type, but that of iron, or of Fe-Si alloys of low silicon composition, was entirely different from the texture of 3 pct Si-Fe. The same effect was noted for the textures obtained prior to normal grain growth, i.e., for primary recrystallization.2 It is the main purpose of the present paper to provide some clarification of this silicon effect. All the HPFe-Si alloys from zero to 3 pct Si, which were rolled by two or more stages separated by anneals, developed (111)[112] type rolling textures.2 Thus, there was no effect of silicon on the rolling textures. Earlier, Gensamer and Mehl3 also found no effect of silicon on the rolling textures of Fe-Si alloys; they obtained the Kurdjum.ow and Sachs (K-S) rolling texture for iron,4 which is characterized as the three ideal components: (100)[011], (112)[li0], and (111)[112]. There is a difference between the HPFe-Si multiple-stage rolling texture and the K-S single-stage rolling texture, but this is a variable processing effect. Of interest here is the fact that the recrystallization textures from (111) [llZ] type rolling textures were different depending on the amount of silicon in the alloy. There was a relatively strong (110) [001] component in the recrystallization texture of HP 3 pct Si-Fe5,8,2 but no such component in HP 0.6 pct Si-Fe, for example; the recrystallization texture for the latter was two (111) [110] type components and a (111) fiber component 1,2 Several publications have shown that a strong (110) [001] recrystallization texture is derivable from a (111) [112] type rolling texture for 3 pct Si-Fe crystals reduced in thickness by about 70 pct.7-10 Furthermore it appears that the strongest of these (110) [001] recrystallization textures occurred when the orientation of the crystal prior to rolling was (110) [001].7 Barrett and evensoon11 found that the rolling texture of a (110)[001] oriented iron crystal was (111) [llj]. Accordingly, it seemed desirable to determine whether a (110) [001] oriented iron crystal, upon rolling and annealing, would behave like the 3 pct Si-Fe crystal (or the polycrystalline HP 3 pct Si-Fe) and thus produce a (110) [001] recrystallization texture contrary to the suggested silicon effect, or would behave like the polycry stalline HP iron or HP 0.6 pct Si-Fe and thus produce (lll) [110] type components in agreement with a silicon effect. Briefly, the idea here involves the use of more precisely defined textures to obtain if possible better control of important variables that affect the recrystallization process. PROCEDURE A (110) oriented crystal of Ferrovac "E" iron (99.9 pct pure) was prepared in sheet form 0.080 in. thick with the [001] direction parallel to the long dimension of the specimen.'' This crystal was etched to 0.073 in. thickness (to remove some small included grains) and then was cold rolled in a 6-in.-diam mill to a final thickness of 0.022 in. The rolling was unidirectional except for an inadvertent reversal at 0.061 in. thickness. At this thickness, and also at 0.040 in., the rolling was interrupted for transmission Laue photographs. Molybdenum Ka-radiation filtered with zirconium was used in a transmission method1' to obtain the cold-rolled (110) pole figure. The sample was a 0.002-in.-thick section taken from the central region of the 0.022-in.-thick cold-rolled crystal. For the primary recrystallization study, cold-rolled samples were etched from 0.022 to 0.021 in. thick and annealed in hydrogen at 850°C. Primary recrystallization to a fine-grained structure, Fig. 1, was obtained in a 5-min anneal. Eleven sheets after

Jan 1, 1963

By A. J. Jacobs

THE purpose of this note is to draw attention to a set of tables, recently compiled in Rocketdyne Research Report No. 64-19, under the title "Crystal-lographic Data for Indexing Cubic Twin Reflections and Cementite (Fe3C) Reflections in Electron Diffraction Patterns."' These tables were an outgrowth of electron-diffraction work conducted over the past several years on steels, precipitation-hardening aluminum- and nickel-base alloys, molybdenum, tantalum, and tantalum-base alloys. The first table lists the indices of possible twin reflections for all the possible twinning planes in bcc and fcc lattices. The twin reflections correspond

Jan 1, 1965

By W. R. Toeplitz

H. N. Ghenn.*—It has been established that the accuracy obtainable from any precision machine is a function of the wear resistance, maintenance and closeness of fit of the bearings, hence I would like to ask Mr. Toeplitz how these oil-less bearings compare with cast iron or babbitt or similar materials when used on precision machinery. Could these bearings be used, for example, on a grinding machine in which work must be held to a tolerance of plus or minus 0.000025 inch? W. R. TOEPLITZ.—The metal-powder bearings can be held to very close tolerances and are used in place of cast iron and babbitt on precision machinery.

Jan 1, 1945

Section 67 Department of Conservation and Development, State of New Jersey, State House Annex, Trenton, N. J. H B Kummel, State Geologist For lists of publications, maps and geologic folios, address the above. Where price of postage is noted, in the following list of available publications on geology, the postage is only to New Jersey and

Jan 1, 1933

By John D. Clark

ONE'S lifetime does not usually offer the opportunity to observe and be a part of the commercial development of an entirely new material. Petalite has been known for over a century, but at first it was presumed rare. However, it was found to be so abundant that it has become a new and extremely useful industrial tool.

Jan 10, 1950

By Alan T. Gorton, T. L. Joseph, Gust Bitsianes

High-temperature X-ray diffraction techniques were used to determine thermal expansion coefficients of iron and its oxides. Lattice parameters of a and iron, wiistite, magnetite, hematite, and goethite were determined and plotted as a function of temperature. From these results, the true and mean linear thermal expansion coefficients were calculated. In the case of noncubic crystals, the expansion coefficients were determined along each of the crystallographic axes. The effect of the magnetic transformation on lattice parameter was measured for a iron and magnetite at their respective curie temperatures. COEFFICIENTS of expansion for iron and its oxides were determined from the temperature dependence of their lattice parameters. From these data, the true linear coefficients were derived by means of the formula: at =[(l/ao )(dao/dt)] [1] where at is the true linear coefficient of expansion, a, is the lattice parameter in angstrom units, and all variables are referred to the temperature, t, in OC. Thus the true expansion coefficient represents the instantaneous change in lattice parameter on a unit basis and at a particular temperature. A second expansion coefficient is also often used. It is termed the mean linear coefficient and is defined in the following way: am = [ao(t) - ao(O)]/ao(0) l [21 This coefficient represents the average change in lattice parameter on a unit basis but at a specified parameter length, ao at O°C, and over a specified temperature range,1 to 0°C. Generally the true co-

Jan 1, 1965

In March 1962, over three months ahead of schedule, production began from the Ventersdorp Contact Reef of the Western Deep Levels Ltd. mine on the West Witwatersrand. Few mines have captured the interest of mining men and the public as has Western Deep Levels. It has presented the gold mining industry with a challenge which involved the opening of an ultradeep mine with the attendant problems of exceptionally heavy capital commitments ($77 million to start of production), high rock temperatures and pressures at great depths, cementation and pumping in an area notorious for the volume of subsurface water, and the necessity for entirely new thinking and the application of new ideas. HISTORY Not all the problems facing Western Deep Levels were, however, new. Situated 43 miles from Johannesburg, just off the main road to Potchefstroom, Western Deep Levels was the sixth company to undertake mining operations on what is known as the West Wits line and it could draw on the wealth of experience gained by other pioneer mines in the area.

Jan 12, 1962

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947