Search Documents

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.' The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.' The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By R. M. Leibrock, C. W. Ziemer, R. P. Vincent

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By R. R. Webster, H. T. Clark

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By James M. Schopf

Gilbert H. Cady (Senior Geologist, Head of Coal Division Emeritus, Illinois State Geological Survey, Ur-bans)— Those coal mining and preparation engineers and operators who read this article will probably be most concerned with those parts which deal with the applied aspects of coal petrology in the fields of mining and technology. Actually the two categories overlap to such a degree that they are essentially one. The article appears to suggest that there are two points of veiw in the field of applied coal petrology. From one viewpoint the interest is in the attributes of the various macerals (Fig. 4)—vitrinite, exinite, and inertinite—-in terms of utilization (when the coal is burned, coked, gasified, hydrogenated, etc.). From the other point of view, assuming that the macerals do possess individuality in behavior, interest attaches to the possibility that coal of a particular type (maceral composition) can be prepared by discriminating methods of preparation and blending. Most of the 29 items listed for mining and technology can be assigned to one or the other of these two categories. Somewhat the same simplicity that resides in the items of the proximate chemical analysis is desirable for the petrologic analysis. This simplicity appears to be fairly well achieved by the group maceral device provided mineral matter is also included. At present, without fully adequate experimental substantiation, the three types of material represented by the group macerals vitrinite, exinite, and inertinite are regarded as sufficiently different in composition and properties so that the preponderance of any one type gives the coal distinctive properties provided it is not too high in rank. This appears to be increasingly true with coals of decreasing rank from medium volatile bituminous coals downward. The article reflects the great emphasis placed on the technique of descriptive coal petrology in America. Such description has resulted in a good understanding of the nature of the fundamental variability in the physical composition of bituminous coals. Such understanding has been attained very largely by the thin section technique used in coal bed profile analysis introduced by R. Thiessen after the manner suggested by the data assembled in Table 11. In contrast, the group maceral concept of coal analysis in terms of the categories indicated on the left hand side of Fig. 4 is particularly useful for broken coal analysis and applied coal petrology, in which evaluation is largely based on quantitative concepts. It is inadequately emphasized in this article that although the Thiessen procedure is suitable for the purpose of petrologic description in which texture and orientation are of critical importance, it is less well adapted to the technological uses of applied coal petrology. No doubt those persons whose interest may have been aroused in the possibilities of more refined coal preparation by this and other recent contributions to the literature of coal petrology will understand that certain technical aspects of coal petrology, particularly in the field of descriptive petrology, are still a matter of some controversy among the coal petrologists, but they will also appreciate that Schopf has made an important contribution to the field of coal petrology in America by pointing out that such petrology requires consideration of disoriented or broken coal samples and that results are expressed less in descriptive terms than in quantitative values with respect to the four types of material composing coal—-vitrinite, exinite, inertinite, and mineral matter. Unfortunately because so much American coal petrology has been descriptive of the coal in the bed there is a dearth of literature on applied coal petrology. Research and experimental data in this field are greatly needed.

Jan 1, 1959

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien's Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By F. H. Rhines

Page Foreword. By F. N. Rhines............................525 Design Factors for the Metal Forms with Which Powder Metallurgy May Compete. By Fred P. Peters...................... ......527 Discussion..................................530 Powder Metallargy as Applied to Machine Parts. By A. J. LanghamMer........531 Discussion......................... . Pole Pieces for Electric Motors from Iron Powder. By F. V. Lenel...........535 Discussion....................... . Bearings from Metal Powders. By W. R. Toeplitz.................542 Discussion.........................'.........549 Brushes and Allied Powder-metal Parts. By R. R. Hoffman . .............'550 Electrical Contacts Manufactured from Metal Powders. By E. I. Larsen........554 Sintered Magnets. By C. B. Fulton........................557 Friction Articles from Metal Powders. By C. T. Cox..................565 Discussion..................................567 Certain Characteristics of Silver-base Powder Metallurgical Products. By I?. R. Hensel and E. I. Larsen........................ ....569 Discussion............................... . . . . 579 Some Properties of Sintered and Hot-pressed Copper-tin Powder Compacts. By C. G. Goetzel..................................580 Discussion..................................593 The Sintering of Metal Powders—Copper. By C. J. Bier and J. F. O'Keefe......596 Some Experiments on the Effect of Pressure on Metal-powder Compacts. By Jerome F. Kuzmick..................................612 Discussion.................................. 630

Jan 1, 1945

By H. R. Shidel

This paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. 8. Bureau of Mines; Magnolia Petroleum -Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," 5. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon, (2) That the only striking connection between structure and water is in .the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by finegrained, well cemented sand, which is barren. Possibly two or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 1, 1920

By Chi-shing Wang

Recently the U.S. Bureau of Mines has undertaken a research project to develop the mechanical roof pulling technique as a method for evaluating the effectiveness and the comparative advantages and disadvantages of various roof bolting systems for underground coal mines, based on the characteristic responses of bolted mine roofs to a prescribed external loading system. Two preliminary experiments of the test method were conducted in the Bureau's Safety Research Coal Mine (SRCM) at Bruceton, Pa., and further trials are underway. The fundamental concept of the test method, the design of test rigs, and the experimental results are summarized in this progress report.

Jan 1, 1976

By N. Rowlands, J. A. Finch, R. Espinosa-Gomez

The sulphation roast-leach process for complex sulphides results in phase changes due to roasting and leaching. The phases in the calcine, and in the neutral and hot acid leach residues were identified and their degree of liberation determined in order to design and Interpret separation tests on the residues. The hot acid leach residue was composed of hematite, silica, and lead sulphate with some associated silver. Magnetic separation was selected as the process for producing a lead concentrate, as the non-magnetic product. Separation was limited by -1 pm hematite reporting to the product, and hematite/lead sulphate agglomerates reporting to the magnetics.

Jan 1, 1984

By Robin P. Gardner

A radioisotope tracer method combined with a suitable back-calculation method is proposed and evaluated for the determination of model simulation parameters in open-circuit continuous ball mills. The method essentially consists of using impulse and/or step injections of short-lived radioisotopes of the naturally occurring trace elements manganese and sodium. It is evaluated here on the basis of the minimum standard deviations of the product weight-size distributions. These minimum standard deviations are taken as those predicted by a Poisson distribution of the number of particles present in size fractions of the samples taken for analysis. Previously developed tanks-in-series lumped parameter models are used in the evaluation. The results indicate that the method is very promising.

Jan 1, 1976

By J. S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1983

By Margaret Dienes, Karl L. Fetters

It is recognized that ingot structure is important in determining the quality of finished steel. Such elements of ingot structure as the size, shape and distribution of primary crystals; the size, shape and distribution of shrinkage cavities; the degree and kind of segregation (both macro and micro); the distribution of nonmetallic impurities and gas cavities are each the result of solidification phenomena. 'These structural features vary with variations in ingot practice. Their control requires a knowledge of their correlation with the variables of ingot practice. The structures of full-sized commercial steel ingots have been studied extensively by the Steel Ingots Committee of the Iron and Steel Institute.l This work has contributed much to our knowledge of ingot structure and the factors that control it. These investigations of necessity have been limited in scope because of their costliness and the great amount of time required. Studies of the structure of small steel ingots have not been very satisfactory because of the rapid rate of freezing of the ingots. Their structures are thus difficult to resolve and to interpret. Medium sizes of steel ingots in the ranges of 150 to 500 lb. do offer opportunity for study, but their cost also becomes greater and their use less expeditious. Experimental models for the study of steel-ingot structure have been made of nonferrous metals. Gathmann2 used lead-tin alloys and reported that they were satisfactory for determination of the location of the major shrinkage cavities and the Liplanes of weaknessv resulting from the pattern of crystallization. Certain features of mold design have been illustrated by these results. Bezdenezhnihk3 has used copper and aluminum ingots similarly and has shown the effect of mold-wall thickness on the depth of columnar grains. These studies of nonferrous models have been useful, but their results have been limited because the analogy with steel ingots obviously is not a close one. Model wax ingots have also been useful in pointing out important features of mold design. Gathmann4 watched the solidification of wax ingots, through a glass-walled mold, and has reported the effects of mold type on the location of the shrinkage cavities. Segregation was simulated by using a mixture of paraffin and stearine and adding a red dye that on freezing segregated preferentially to the stearine. Brearley5 also used wax models to determine the effects of some of the principal features of mold design. Carlsson and Hultgren6 dsed stearic acid to show that the columnar crystals of ingots tend to slope upward progressively from the mold wall toward the center of the ingot. As with the nonferrous ingots, the wax ingots have

Jan 1, 1943

By Margaret Dienes, Karl L. Fetters

It is recognized that ingot structure is important in determining the quality of finished steel. Such elements of ingot structure as the size, shape and distribution of primary crystals; the size, shape and distribution of shrinkage cavities; the degree and kind of segregation (both macro and micro); the distribution of nonmetallic impurities and gas cavities are each the result of solidification phenomena. 'These structural features vary with variations in ingot practice. Their control requires a knowledge of their correlation with the variables of ingot practice. The structures of full-sized commercial steel ingots have been studied extensively by the Steel Ingots Committee of the Iron and Steel Institute.l This work has contributed much to our knowledge of ingot structure and the factors that control it. These investigations of necessity have been limited in scope because of their costliness and the great amount of time required. Studies of the structure of small steel ingots have not been very satisfactory because of the rapid rate of freezing of the ingots. Their structures are thus difficult to resolve and to interpret. Medium sizes of steel ingots in the ranges of 150 to 500 lb. do offer opportunity for study, but their cost also becomes greater and their use less expeditious. Experimental models for the study of steel-ingot structure have been made of nonferrous metals. Gathmann2 used lead-tin alloys and reported that they were satisfactory for determination of the location of the major shrinkage cavities and the Liplanes of weaknessv resulting from the pattern of crystallization. Certain features of mold design have been illustrated by these results. Bezdenezhnihk3 has used copper and aluminum ingots similarly and has shown the effect of mold-wall thickness on the depth of columnar grains. These studies of nonferrous models have been useful, but their results have been limited because the analogy with steel ingots obviously is not a close one. Model wax ingots have also been useful in pointing out important features of mold design. Gathmann4 watched the solidification of wax ingots, through a glass-walled mold, and has reported the effects of mold type on the location of the shrinkage cavities. Segregation was simulated by using a mixture of paraffin and stearine and adding a red dye that on freezing segregated preferentially to the stearine. Brearley5 also used wax models to determine the effects of some of the principal features of mold design. Carlsson and Hultgren6 dsed stearic acid to show that the columnar crystals of ingots tend to slope upward progressively from the mold wall toward the center of the ingot. As with the nonferrous ingots, the wax ingots have

Jan 1, 1943

By B. M. Larsen, W. E. Shenk, T. E. Brower

Shortly after our previous paper on this subject was printed1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100" C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination SO far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E. Apparatus The final form of apparatus we have used is identical with that described and illustrated in our previous paper, except for the substitution for the Globar furnace of a small high-frequency furnace actuated by a vacuum tube oscillator2 0f about 1.5 kw. capacity, and for a slight modification of the containing vessel. This transparent silica vessel is illustrated in Fig. 1 of this paper. Its enlarged portion is about 5 cm. in diameter and 13 cm. long. The silica tube for inlet of hydrogen is fused into this bulb and ends beneath the metal "bucket" holding the steel sample. This sample is in the form of fine millings. The "bucket" is suspended by a platinum wire from the cap of Pyrex glass. The high-frequency

Jan 1, 1934

By Albert E. Wood, Edgar R Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as ''308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By Albert E. Wood, Edgar R. Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as ''308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By Marc Lemieux

Computer pit design techniques generally make use of models in which the deposit is represented by a regular array of data. Using a regular system, the number of data points required to represent the air, waste and mineralization in a large deposit become excessive. The number of blocks used to describe the deposit is dependent upon the block size. The quality of the pit wall slope design also is dependent upon the block size used and the method of defining the slope. The error associated with reserve calculations becomes greater with increasing block size. A deposit model consisting of variable sized air and mineralized blocks has been developed at the University of British Columbia and improved upon at Climax for pit design work. The method permits put- ting the entire model in core for rapid data processing. This permits the use of a versatile cone generation technique which allows close adherence to variable slope constraints in all directions. The conical shape is approximated by rectangles on each level which equal the area of the ideal conical intersection. The shape of the intersection may vary from approximately circular to elipsoidal. The approximate cone shape is controlled by the slope constraints applicable at the point of intersection on the bench. The overall modeling technique greatly assists the pit design engineer in developing a high quality pit design.

Jan 1, 1977

By M. Paulus

It is known that multicomponent powders are mostly nonhomogeneous. This paper investigates the effects of nonhomogeneity of composition and grain size on the melting point and the sinterability of compact taking into account homogenization mass transport and the length of the diffusion path in solid state sintering, and the kinetics of liquid phase formation in liquid phase sintering. After a discussion on the ideal characteristics of a powder for sintering and low temperature reaction, the main conventional processes are compared. Finally we develop the freeze-drying technique and demonstrate the capabilities and the limits of the process by some examples, mainly in the ceramics field.

Jan 1, 1980