Search Documents

By E. G. Woods, A. G. Comer

A mathematical model is presented and solved for determinution of the saturation distribution and pressure in a radial gas-storage reservoir. The model consists basically of two parts: (I) the growing gas-bubble core, and (2) the surrounding aquifer. Since the total pressure at the injection well is a function of the two-phase flow in the gas bubble and the unsteady single-phase flow in the aquifer, the resistance to flow in both zones was taken into consideration. The assumptions involved for both the radial equivalent of the Buckley-Leverett two-phase-flow equation and the injection-pressure equation are as follows: (I) the geometry is radial, (2) the gas bubble is free to expand or contract, (3) compression or expansion of the gas within the bubble may occur at the beginning of a time step, (4) the fluids are immiscible, (5) water is incompressible within the gas-storage region whereas it is compressible outside of this region, (6) a stable gas-water interface exists and (7) gas injection occurs at a constant rate or a series of constant rates. The mathematical model was solved numerically using an IBM 650 computer. A comparison is presented between the predicted results of the model, the results assuming steady-state flow and the actual initial injection-pressure history of an operating reservoir. Using the initial field pressure for a basis, the average deviation between the predicted pressure and the actual field pressure was less than 4.3 per cent. INTRODUCTION Underground storage of natural gas in abandoned oil fields, in abandoned coal mines, in caverns and in aquifers has had varying degrees of success. The lack of these first three facilities in the vicinity of most major gas marketing areas is leading more and more to storage in virgin aquifers. For the most part, this storage in aquifers has led to the study upon which this paper is based. Several excellent papers have been published discussing the problems involved in the underground storage of natural gas; however, to these writers' knowledge, none of them considered the two-phase flow of fluids in the gas bubble and the fact that the gas bubble will grow or shrink in size depending upon the injection and withdrawal history of the reservoir. Not only will both of these factors influence the required injection pressure, but also they will have a definite bearing upon the amount of water production occurring upon withdrawal from the storage area. To solve this problem on an IBM 650 computer, several simplifying assumptions were made. Only the drainage portion of the relative-permeability curve was considered, thereby neglecting any hysteresis effects introduced during an imbibition cycle. The quantity of gas withdrawn during the period of the field study was only a small percentage of the total gas in place; therefore, this assumption is justified. For the problem studied in this case, the combined effects of capillarity and gravity were assumed to be negligible. This assumption becomes less valid as the formation thickness or the average pore diameter increases markedly. The justification of these assumptions should be studied in each case. THEORY This mathematical model for the prediction of saturation distribution and pressure for a radial gas-storage aquifer is based upon the equations for radial two-phase fluid flow'.' and for radial, unsteady-state, single-phase fluid flow.' The two-phase flow is considered to take place in a "core" whose radius is equal to the maximum radius that the gas zone will attain, as indicated in Fig. 1. The injection-withdrawal history is approximated by a series of constant flow rates. Within the "core", gas is assumed to behave as a semi-compressible fluid; that is, the gas is assumed to have a constant density based on the average gas-zone pressure for the flow period. Between each constant-rate time increment, the gas density is allowed to change. This involves an iterative solution of the pressure equation. The liquid phase in this zone is considered to be incompressible, whereas it behaves as a compressible liquid outside of this region. The equations of incompressible flow in the "core" may be written for the gas phase

By W. D. Faulkner, J. E. Urbanic, R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in carbon-in-pulp and carbon-in-leach circuits has been investigated. Carbons from two US mines, one Canadian mine, and a South African pilot plant operation were characterized before and after regeneration. Thermal regeneration of the carbon was investigated using factorial analysis to determine the effect of interaction of furnace temperature, retention time, and use of supplemental steam. The operation of acid washing the service carbon was investigated, including a comparison of the use of nitric and hydrochloric acids. The effect of quenching regenerated carbon was also briefly studied. Prom the data obtained, guidelines are given for effective regeneration operation.

Jan 1, 1986

By Axel Sahlin

Since the days of the infancy of metallurgical industries, slags of various kinds have been accumulating. Until a comparatively recent date hardly any employment had been found for these waste products, which have had, consequently, little or no value. An exception to this rule is the basic Bessemer slag, the value of which has become universally recognized. It is to-day one of the standard fertilizers of the world, and a price of from $15 to $20 a ton is considered reasoiable for the ground slag, which, especially in Germany, finds a ready market as fast as it is prepared. The slags from puddling and re-heating furnaces have only found vol. xx.—25

Jan 1, 1892

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By E. H. Crabtree, T. C. King

The ferrosilicon grinding unit at the Central Mill of the Eagle-Picher Mining & Smelting Co. near Picher, Okla., was completed in March 1947. The object of the plant was to grind pigs of ferrosilicon, having a size of approximately 1½ by 4 by 12 in. and an analysis of 85. pct Fe and 15 pct Si, to approximately 100 mesh by crushing and wet grinding in a ball-mill classifier circuit. The minus-100 mesh ferrosilicon had formerly been purchased, and was used as medium in the heavy media process for treatment of lead-zinc ores. From the standpoint of dollars and cents, the cost of minus-100 mesh ferrosilicon was roughly $40.00 per ton more than pigs of the corresponding alloy delivered to the mill. Estimated wet grinding costs were considerably below this figure. The possible saving in cost of make-up medium for the cone plant was particularly attractive since, at that time, the plant losses averaged over four tons of minus-100 mesh ferrosilicon per day. Aside from the probable saving on the grinding charge, the need for such a unit was twofold. First, periodic fluctuations in the differential between the top and bottom densities of the cone were thought to be detrimental to metallurgy. There was little doubt that an intermediate differential existed at which the heavy media separa- tion was most efficient, representing a compromise between concentrate grade and tailing loss. Furthermore, if a finer, but considerably cleaner, medium could be obtained, there was the possibility that the differential could be decreased without increasing the viscosity, or conversely, the viscosity of the medium decreased without increasing the differential. Preliminary to experimental work aimed at pegging the cone differential and circulating medium viscosity at whatever values were found to be most efficient, it was essential to have control over both the nonmagnetic content of the medium and the particle size of the contained ferrosilicon. The latter was possible by means of a grinding unit at the mill. Second, whereas the ferrosilicon alloys are made by a number of manufacturers, only two, to our knowledge, grind it in any quantity for use in heavy media plants. For all practical purposes, the Central Mill was limited to one source of supply, a particularly vulnerable position. In case the supply was cut off, it was thought that pigs of the 85 pct Fe, 15 pct Si alloy could be obtained elsewhere, providing means of grinding them was available. There was no published information available covering wet grinding of ferrosilicon. Dry grinding in batch mills and in continuous mills with air classification was being practiced, but the cost of grinding was excessive and the dust condition objectionable. It appeared that primary and secondary crushing was no particular problem, providing heavy duty equipment was used;

Jan 1, 1949

By Robert H. Richards

Jan 1, 1883

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By Elmer W. Pehrson

OPINION seems widely divergent as to where we stand with respect to future mineral supply. From some quarters we hear that the United States is about to become a "have-not" nation and about to experience the evil consequences such a situation would entail. Others claim that we are still a treasure house of stored-up mineral wealth, the surface of which barely has been scratched. The data to be presented here support the conclusion that neither of these viewpoints is correct and that we are far from exhaustion of those mineral resources that are basic to our industrial economy. However, exhaustion is well advanced in a number of important subsidiary minerals so that we can no longer drift along with the easy-going philosophy that the earth will provide. The time has come when we must recognize the true situation and do something about it.

Jan 1, 1945

By G. R. Smithson, John E. Hanway

This paper, the first of two papers covering the development of a metallurgical process for the treatment of a complex ore, describes the bench-scale experimental Program undertaken as a basis for initial process design. The results of using various potentially applicable process steps are detailed and the basis for selecting certain of these steps for Pilot-plant development is outlined. A process consisting of the steps of sulfate roasting, leaching, copper recovery, solution purification, zinc electrolysis, and brine leaching for lead recovery was recommended for further study. THIS paper describes the bench-scale development of a sulfate roasting process designed to recover copper, lead, and zinc from a complex ore. The extrapolation of the bench-scale results to pilot-plant design and the results of pilot-plant operation will be described by Lund, et al.' in a subsequent paper. Several years ago, the research divisions of the St. Joseph Lead Co. became responsible for the development of a metallurgical procedure to treat a complex sulfide ore containing copper, zinc, and lead sulfides. The primary objective was to devise a procedure which would permit economic recovery of the nonferrous values. As could logically be expected, the study of conventional flotation procedures was undertaken; in addition, however, because the physical nature of the mineral association in the complex ore indicated that physical methods of ore beneficiation might not prove to be entirely satisfactory, a program also was established to investigate alternative methods of direct metallurgical treatment for recovery of the metal values. Exploratory test work by the St. Joseph Lead staff led to the conclusion that a sulfate roasting technique represented the most attractive approach for a direct metallurgical process. Sulfate roasting would provide for the selective conversion of the nonferrous values to forms soluble in conventiona1.1 leaching agents and would permit their efficient separation from the insoluble iron and other gangue materials. It should allow efficient utilization of the thermal energy available from oxidation of the sulfide raw material, and might provide an opportunity for recovering byproducts such as iron and sulfur. The decision to evaluate a selective sulfation procedure as a basic processing step also was influenced by the excellent results obtained by the St. Joseph Lead Co. in using this procedure for the recovery of cadmium from zinc sulfide concentrates. The choice of selective sulfation as a major processing step served as a basis for an extended experimental investigation of the process with bench- and pilot-scale equipment to prove its feasibility. St Joseph Lead Co., aware that Battelle Memorial 1nstitute had participated in the development of several fluidized-bed sulfate roasting procedures, asked Battelle to undertake the bench-scale development of a suitable sulfation process. This paper describes the procedure used and the results obtained at Battelle in the treatment of the complex sulfide ore. EXPERIMENTAL WORK Nature of the Raw Material. The sulfide ore deposits of interest are essentially a massive sulfide, with the indivudual ore minerals being extremely fine grained and intimately intergrown with each other and with the associated gangue. The zinc in the ore is present mainly as sphalerite (ZnS), the lead as galena (PbS), and the iron either as pyrite (Fes2) or as pyrrhotite (FeS). Table I shows the chemical analysis of various individual samples of the ore. These analyses illustrate the variability of the ore body and impose a rather severe requirement on any type of metallurgical process—that of being able to tolerate probable wide variations in the assay of the head ore. The tentative flowsheet designed to serve as a guide for the initial experimental investigation of

Jan 1, 1962

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By John Birkinbine

EXTENDED discussions, by inviting attention to problems affecting the conservation of natural resources, have encouraged investigations as to their sufficiency, with the general result that the more thorough the examination, the less cause appears for anxiety as to the exhaustion or serious depletion of these resources. The extent of industrial development, the large plants and the enormous volumes of materials required, when compared with conditions a few decades ago, are sufficiently startling to enlist the attention of those who "fear .the pace," and yet in but few instances has real solicitude for the future. been warranted by a knowledge of true conditions. In a former communication, presented 5 years ago,1 I endeavored to emphasize the fact that true conservation represented the best utilization of reserves and not the locking up of resources for future use; a conviction which has become more pronounced as the subject was investigated. Prophecies of the, early exhaustion of mineral resources have raised the question as to our permanent reliance upon these, and encouraged inquiries which have in most cases developed reassuring conditions. But the fact that the future appears less dark than prognosticated cannot excuse wastefulness or improvidence; and detailed study which demonstrates an apparent abundance of natural resources should encourage their best application. In making inventories of resources one is liable to confine conclusions as to availability upon present circumstances and conditions in the past, or to formulate data for the future upon methods which are rapidly being displaced. In reserves which are not reproductive, such as minerals, the possibilities of exhausting the supply are startling if estimates assume that future extensions will follow methods which were less economical than those now employed, or to he used, and we dare not claim that the limit of advanced practice has been attained.

Jan 9, 1914

By John M. Karpinski, David S. Cahn

For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate tests. In addition, the dependence of these tests on such pellet properties as size and weight was to be investigated.

Jan 7, 1969

By T. E. Brower

SHORTLY after our previous paper on this subject was printed,1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100° C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and. reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination so far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E.

Jan 1, 1934

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By W. C. Weslow

AN extended program devoted to the development of a matrix for holding diamonds of a size and kind not heretofore generally used is being carried on by the Carboloy Company, and this paper describes the part of the development that affects mining and its allied industries. Laboratory and field work so far has indicated the following: 1. Tungsten carbide and cobalt form the most desirable known matrix material for the holding of diamonds for drilling work. 2. Industrial bort diamonds in sizes and of a class not generally heretofore acceptable and therefore less expensive can be successfully held in this cemented carbide matrix. 3. In exploratory drilling, the combination of bort diamonds, impregnated throughout a matrix of tungsten carbide and cobalt, when fabricated onto drilling crowns, is an indicated economic substitute for drilling crowns in which the diamonds are set by hand, mechanically or by casting. 4. This impregnated type of drilling crown or bit has definite possibilites of revolutionizing the drilling of blast holes, particularly in the harder formations. This will be brought about by the development of high-speed light-weight rotary equipment using an impregnated diamond bit to replace the percussion drill now in general use. (The development of this rotary equipment is well past the laboratory stage at this time.) 5. That the use of a rotary bit is a preventive measure in the fight against silicosis. The development of this product was started by G. F. Taylor at the Research Laboratories of the General Electric Co. It was early recognized that it had possibilities in the drilling field and the present product is the result of considerable experimental work with other powdered metals as well as with tungsten carbide and cobalt. In the study of the potential application to the mining field, it was learned that carbon diamonds originally were given a high rating of performance but that the trend had been toward borts in selected sizes

Jan 1, 1940

By Albert Sauveur

The instrument about to be described meets so perfectly the special needs of the metal microscopist that there eeeme to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.—The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement affords free space below the objective for the examination of large epecimens of metals, such as full rail-sections, without detracting in the least from the value of the

Jan 1, 1912

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By J. Burbank

A TECHNIQUE has been developed for the microscopic study of the three-dimensional structure of the Pb-Sb alloys by the formation of a chemical replica in which the internal structure of the metal may be seen directly. In the replica process one of the phases present in the structure as-cast is converted into a translucent material, and the second phase remains virtually unaffected, permitting microscopic examination by transmitted light. Alloys of lead and antimony were made from the chemically pure metals, cast in a sooted and pre-

Jan 1, 1954