Search Documents

By R. L. Perrine

A stability theory is developed for miscible liquid-liquid displacement within a porous medium. In the usual case considered, a high-density high-viscosity "oil" is displaced downdip by a low-density low-viscosity "solvent'! Perturbation methods are used to find the conditions under which the spreading mechanism changes from the stable dispersion process to unstable viscous fingering. We find that instability is conditional, that there is a dependence on the shape of a disturbance leading to a"diameter" effect and that very difficult experimental scaling problems may result. A useful consequence is the definition of a minimum "slug size" for stable miscible displacement. This should make possible optimum use of the solvent process for oil recovery. The results may apply to many situations in which one fluid displaces another of somewhat different fluid properties within a porous medium. INTRODUCTION The process of miscible liquid-liquid displacement looked very favorable when it first received serious consideration as a means to increase petroleum recovery. Some early laboratory results were interpreted to mean that only a small "slug" of solvent was needed, perhaps 2 to 3 per cent of a hydrocarbon pore volume. This "slug" could recover the oil in an entire reservoir provided the fluids remained miscible.1,2 Only a slow growth of the "mixing zone", or gradual transition from oil to solvent, should occur. This would follow naturally from mixing by a dispersion mechanism such as that described by Scheidegger.3 And, indeed, laboratory cores have shown this kind of behavior provided solvent viscosity was at least as great as that of the oi1.2,4-6 The same kind of behavior has also been observed with solvent viscosity lower than that of the oil after the distance traversed became large. Not all laboratory results have been this favorable, however.7-9 Mixing zone growth may become proportional to the distance traveled rather than the square root of this quantity. Such behavior accompanies high rates in short systems of large diameter, provided the viscosity ratio is adverse. If this more rapid spreading were to persist in a reservoir, the solvent requirement for miscible "slug" displacement could exceed 30 per cent of a pore volume. There is considerable economic importance in the difference between 3 and 30 per cent solvent. A 1ogical conclusion is that two different kinds of flow behavior are possible, with each kind leading to a different result. One kind gives efficient displacement, the other does not. In the efficient case, the solvent bank spreads out only by the mechanism we have termed dispersion. Under these conditions, displacement is as near piston-like as possible. In the second kind of flow, found only with adverse viscosity ratios, viscous fingering occurs. That is, permeability variations cause a small finger of low-viscosity solvent-rich fluid to move ahead of its average position within the mixing zone. This creates a path of low resistance to flow, and an even greater amount of solvent-rich fluid follows. Thus, the process is autocatalytic. Once started, the fingering mechanism rapidly becomes dominant. The question to be answered is this. Under what conditions will each of these two different kinds of flow occur? In particular, what conditions denote the transition from dispersion to viscous fingering as the solvent spreading mechanism? The answer may tell us whether or not the desirable, near piston-like miscible displacement process is practical. An answer to this problem can be obtained from theory by the use of perturbation methods. The procedure is as follows. We first formulate a mathematical representation of the system. Then a small disturbance (or perturbation) in solvent concentration profile is introduced and observed to see what happens. Unstable flow is indicated when a small disturbance will grow larger. This will lead to eventual viscous fingering. If on the other hand the disturbance dies out, the displacement is stable. In this latter case, with dispersion as the spreading mechanism, near piston-like displacement is possible. Thus, this paper presents the development of a stability theory for miscible liquid-liquid displace-

By F. F. Aplan

INTRODUCTION The production of coal is a major part of the mining industry. In recent years the production of clean coal has exceeded 600 million tons per year and is reported to have reached 660 million tons in 1977. Some data on the magnitude and utilization for the year 1975 is given in Table I. In that year 648 million tons of soft coal were produced and of this 267 million tons or 41% approximately was produced by mechanical cleaning. Of the 374 million tons of raw coal sent to the preparation plant, 28.6% or 107 million tons was discarded as refuse. In the same year approximately 6 million tons of anthracite were produced and nearly all of this was cleaned. Table I also gives coal utilization statistics for 1975. Excluding the approximately 20% that goes to the coke ovens or to export, the vast bulk of our production is used for steam power generation and a lesser amount for captive production of industrial power and process steam. While much of the nation's coal (e.g. strip mined western, sub-bituminous coal) may be removed from the ground in relatively pure form by modest selective mining techniques, other coal requires preparation in order to remove ash and sulfur constituents and produce an acceptable steam or coking coal. Preparation is often a valuable adjunct to mining in that rather non-selective, low cost, bulk mining techniques may be used underground while the preparation plant is used to reject refuse at low cost above ground. The principal reason for the use of coal preparation is to convert raw coal into an acceptable commercial product by removing the high ash and high sulfur refuse material.

Jan 1, 1979

By W. H. Adams

At the present time all the larger and better chemical works of Europe and the United States have introduced, as essential factors in the economical manufacture of sulphuric acid, both Glover towers and Gay-Lussac absorbing columns. The clear exposition of facts given by Bode and Lunge in their very valuable technical contributions since 1870 has slowly but surely brought about radical changes from the old methods of manufacture ; but while the Gay-Lussac column has been known since 1827 and the Glover tower was originated in 1869, yet no theoretical treatise covering the subject fully was given to the world until 1876, when the various contrivances for demonstrating nitrous vitriol were described and criticized by Fr, Bode in a paper "On the Glover Tower" which obtained the great prize of the Berlin Society for the Promotion of Industry.*

Jan 1, 1887

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

By Gen-Hua Shi, Richard E. Goodman

In hard, discontinuous rocks, failure modes and stability are controlled to a great extent by the intersection of discontinuities with the excavated surface. We have solved the general problem of finding the shape and size of all blocks formed through the inter- section of any number of joints and excavation surfaces and will demonstrate a simple graphical method for determining which of these is the "keyblock." An example will explain this methodology applied to a simple open pit. The effects of slope curvature in plan or section, will be demonstrated. Finally, we will show how to determine the optimum orientations for the cut slopes. The methodology is based upon a powerful topologic theorem concerning the finiteness of spatial intersections. This paper is a companion to another dealing with underground openings in the Proceedings of the 22nd Symposium on Rock Mechanics (MIT) , July 1981. This paper discusses the rock blocks created by the intersection of discontinuities and excavation surfaces in a rock mass. It establishes principles and procedures by means of which those blocks that are finite and critically located can be identified and described. The main assumptions are the following: 1. The rock itself is assumed to be strong so that the only concern for stability is the movement of rock blocks them- selves.

Jan 1, 1983

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well's drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well's limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well's cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well's drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By Joseph Mac Donald

Stripped of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it; and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If he fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be

Jan 1, 1909

By P. Bouéry

This account of a contrivance which has been found serviceable in practice may be of interest to engineers, and especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects—namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle.' This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture) the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Jan 1, 1907

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

The next meeting of the Institute, the 113th meeting, will he held in Arizona in the latter part of September, 1916. All papers to be presented at this meeting must be published in the September Bulletin or previously. Manuscripts must, therefore, be in the hands of the Secretary of the Institute not later than July 1. In case manuscripts are given by authors to members of technical committees, or others, they must be in the hands of such persons sufficiently in advance so that they may be actually in the hands of the Secretary of the Institute by the date mentioned. In the past, the Secretary has received urgent requests for special consideration regarding manuscripts that come in after the closing date. In view of the obvious unfairness of this, the Committee on Papers and Publications has instructed the Secretary not to accept for presentation at the Arizona Meeting any papers received later than July 1, 1916.

Jan 4, 1916

By Robert D. Pike

IN November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: [ ] Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2,3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depend¬ing upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1947

By J. B. Seabrook

The accompanying Fig 1 is a graphical scheme of intermediate accuracy for expediting interconversions of mol, weight, and volume percents. This chart consists of a family of curves of mol or atomic or volume percent plotted against weight percent, each curve in the family providing for a certain ratio of molecular or atomic weights or densities. Thus, the whole range of variations is presented in a very familiar format, and the conversion is effected simply by choosing the proper curve and reading off the required values. An entire series of conversions for a given binary system can be found by following the appropriate curve. It is interesting to examine the analytical geometry of the plots. The curves, which must fit into a square and all join at the 0 and 100 pet points, may be shown to be hyperbolas with their centers on the extension of the diagonal of the square which they intersect. Multiplying out the expression x A atomic fraction of A = y = ------ where x is the weight fraction of A, and A and B are atomic weights, we get xy+A/By- A/Bxy=x Upon rotating and translating axes and avoiding imaginaries, it is found that the angle of rotation is —45°, the origin moves upv2/2 units andv2/2(A/B+1/A/B-1) units to the right, and the standard form is Thus the curves are equilateral hyperbolas, their centers are units away from their intersection with

Jan 1, 1950

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By C. W. Price, G. A. Wheeler

BERYLLIUM has always been a difficult material to prepare for metallographic examination. Severe surface deformation occurs during mechanical grinding and polishing, and a suitable bright-field etchant has not been developed. Certain electrolytic techniques produce satisfactory polishes, but these techniques have not yielded entirely consistent results. Furthermore, they have not provided satisfactory bright-field etches. The purpose of this paper is to describe an electrolytic polishing technique that can also provide an excellent bright-field etch. In addition to the bright-field etch, other advantages of this technique are excellent reproducibility, rapidity, and ease of polishing and etching. Experimental Technique. Specimen Preparation. Beryllium specimens may be either mounted or unmounted for the use of this technique, and the size of the specimens is not important. Specimens with surface areas up to 4 sq cm have been electrolytically polished and etched successfully with this technique. The most important requirement is to provide a good electrical contact to the specimens, preferably on the back of the specimens. When specimens are mounted, a hole is drilled through the back of the mount so that the specimen can be contacted with a probe. Conventional metallographic grinding techniques are used to prepare the specimens for electrolytic polishing. The specimens are ground on silicon carbide papers. Grinding through the usual series of papers down to the 600-grit paper is recommended to minimize the electropolishing time, although successful electrolytic polishes and etches have been obtained by grinding only through the coarser papers. A continuous flow of water is used during grinding to provide lubrication and to minimize contamination. Mechanical polishing is not required because high rates of material removal are achieved with the electrolytic polishing. Polishing. Most of the results reported in this paper were obtained with a "Disa-Electropol", manufactured by Struers Scientific Instruments of Copenhagen, Denmark. Satisfactory results have also been obtained with the conventional beaker technique of electrolytic polishing, however, the conditions applicable to both the Disa unit and the beaker technique will be described. Stainless-steel cathodes are used in both techniques. In the beaker technique, a flat cathode, with an area at least twice that of the specimen, is used, and the specimen is held parallel to the cathode. The distance between the specimen and the cathode affects the quality of the electropolish. This distance is set at about 7 mm in the Disa unit; the same distance produces the best results in the beaker technique. Specimen-cathode distances greater than about 20 mm produce considerable relief, while distances less than 7 mm cause high current densities that are difficult to control. An electrolyte of 2 pct HC1, 2 pct HNO3, and 2 pct HCIOl in ethylene glycol gives the most satisfactory results for both electrolytic polishing and etching. This electrolyte was developed by altering the composition of a similar electrolyte used for electrolytic lapping1 and adding HClOl to improve the etching characteristics of the electrolyte. Variations of from 0.25 pct to as much as 5 pct of each of the acids do not significantly affect the results, but the greatest amount of control and reproducibility can be obtained with the composition of 2 pct of each acid. Generally, lesser amounts of the acids produce lower polishing and etching rates, while greater amounts of acids cause high current densities that are difficult to control.

Jan 1, 1968

By W. L. Grose, J. E. Nealy

A device developed by the U.S. Bureau of Mines for the detection and quenching of coal mine explosions suffers from the inability to discriminate between the light emitted from hydrocarbon combustion and that emitted by electrical sparks and miner's cap lamps1. Since the quenchant device is activated by an internal explosive charge, the possibility of serious injury to nearby personnel demands a detector which can reject false signals. Described herein is a detector which can provide a rapid response signal upon the emission of radiation from hydrocarbon combustion and concurrently reject spurious signals from such sources as sparks and cap lamps. It was suggested that a detector might be developed to operate on the principle of monitoring the radiation intensity emitted from two separate spectral regions and ratioing the intensities2. A series of experiments was conducted for combustion of methane-air mixtures which demonstrate the ability of such a detector to discriminate between combustion and spurious signals. Experimental Apparatus A cylindrical (3.8 in. diam by 12 in.) stainless-steel shock tube test section was used as a combustion chamber. The test section was equipped with quartz windows (2 in. diam) on either side, a piezoelectric pressure transducer, and two steel electrodes. A 10-kv capacitor discharged across the electrodes provided a submicrosecond duration spark to ignite the gas mixture within. The desired partial pressures of methane and air were obtained by using a Wallace and Tiernan 0-800 mm Hg pressure gauge with which pressures could be determined to an accuracy of % mm Hg. All tests were conducted with a total pressure of 1 atm in the chamber. To

Jan 1, 1972

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength-temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates. IN most routine experimental work on products and processes, method:; of operation and product evaluation are established from accurately controlled laboratory tests. With particular emphasis on the pelletization of fine iron ore concentrates, standardized procedures of laboratory production and product testing have been established at Cleveland-Cliffs Iron Co. Research Laboratory at Ishpeming, Mich. A program of this nature was used for investigating the agglomeration characteristics of various iron ore concentrates. The factors which control the process were studied and subsequently controlled for these investigations. Pelletizing as applied to iron ore agglomeration involves the preparation of spheroidal masses from a fine moist concentrate, followed by high-tempera-ture firing to produce a final product. The preparation of moist spherorids is generally designated as balling. This produces the so-called green pellets or balls. After, these have been fired they are called pellets. Balling is accomplished by rolling moist concentrates in a revolving drum until small spheroids form by a snow-balling action. These balls are then heated in a shaft furnace, or a modification of this device, to a temperature high enough to cause agglomeration within the individual balls while they descend countercurrent to hot oxidizing gases. By this process the lour strength balls are converted through various chemical and physical-chemical processes into hard pellets. With correct balling and firing, the pellets are strong, resist abrasive action and handling treatments, and provide a suitable blast furnace and open hearth feed. In 1950 Tigerschiold and Ilmoni developed a working hypothesis to explain the formation and stability of green pellets.' Their work was presented on the basis of geologists' discoveries concerning the soil-water system and C. V. Firth's early postulates of green pellet formation.' Fundamental reactions oc-curing within fired pellets have been described by Cooke and Ban, who showed the microstructure changes caused by different firing temperatures." All these investigators have provided scientific clarifications of agglomeration by the pelletizing process and have opened avenues for greater development. Mineral grain growth and ceramic bond formation are the two basic phenomena imparting coherency to particles within a fired pellet of iron ore. Each of these is established by the transfer of thermal energy to the mineral particles. Grain growth mechanisms are chiefly physical reactions wherein smaller particles consolidate into larger ones, with resulting decrease in surface energy conforming with the second law of thermodynamics. Ceramic bond formation is a chemical reaction usually between basic and acid metallic oxides of the gangue and ore minerals. CaO, MgO, A1203, and FeO of Fe3O4, react in varying proportions with SiO, or Fe2O3, to form a great series of compounds or amorphous solid solutions. These product bond iron mineral particles together by a bridging action or by direct reaction with the surfaces of the particles. The result of the grain growth-ceramic bond formations is a consolidated, coherent compact of gangue and iron minerals formerly held together by much weaker bonds of interstitial water and forces common to dry, unconsolidated particles.4 With respect to iron ore agglomeration, these high temperature bonding reactions have been described by Schwartz, who referred to the bonds in sinters," and by Cooke and Ban, who referred to the bonds in fired pellets." The extent of the bonding phenomena and the consequent strength of fired pellets is governed by

Jan 1, 1954

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By George B. Clark, Edward E. Hornsey

Pulses from large underground explosions which traverse the rock beyond the "fracture" and "plastic" zones do not behave as a spherical elastic model. Observed attenuation is greater than that predicted by the elastic wave equation, and the pulse form changes in a different manner, i.e., it usually lengthens with the first power of the distance. To more clearly define a mathematical real earth-wave model, detailed analyses of the spherical elastic and the Voigt viscoelastic models have been made, and results compared with observed wave forms from large confined chemical and nuclear explosions. TRANSIENT SPHERICAL ELASTIC WAVES Scope of Investigation Transient elastic spherical waves were investigated in detail. However, an elastic model is not, in general, an exact representation of wave propagation in rock. An understanding of transient elastic waves is desirable for gaining insight into explosive-generated wave phenomena because it can be employed for comparison of more complex and realistic models, such as the Voigt model, or others which may simulate real earth waves. The study was concentrated primarily on the peak values of the radial wave parameters : displacement, particle velocity, acceleration, stress, and strain.

Jan 1, 1972

By K. B. McQuillin

The increasing volume of data produced by the Anglo American Corporation of South Africa, Limited, during the course of coal exploration prompted the establishment of a computer based processing system for coal data. This system, known as the Coal Mine Evaluation System, consists of geological, mine planning and financial evaluation sub-systems. This paper describes the use of the geological sub-system in assessing the surface mine potential of a portion of the Witbank Coalfield, South Africa, in which more than one thousand core boreholes have been drilled to date.

Jan 1, 1977

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 8, 1979