Search Documents

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By W. J. Sharwood

Cupellation is well known to be one of the most effective methods of separating silver and gold from base metals and other impurities, as well as one of the most accurate means for their estimation. In the latter application it consists in absorbing in some porous medium the fused lead oxide formed by the oxidation of the lead "bath," which carries with it the oxides of other base metals present. It has long been recognized that small amounts of both silver and gold were removed and absorbed together with the base metals, as well as being to some slight extent volatilized, and in work of the highest accuracy a correction is made for the "cupellation loss." Thus in the assay of bullion this is done by means of "proofs" of like composition, which are manipulated throughout in precisely the same manner as the assay pieces, and are assumed to lose or gain like amounts. In the case of certain very rich ores and commercial products the loss is adjusted by assaying the cupel itself and recovering the precious metal absorbed, but this doubles the labor and does not remedy the loss by volatilization. Arbitrary tables have been drawn up by various authorities with the object of enabling a correction to be applied without the use of a check. These have been of very limited practical use owing to the fact that a number of factors affect the losses sustained. For a fixed amount of precious metal the loss varies with the amount of lead used, with the nature and amount of the impurities, with the porosity of the cupel, with the air supply, and above all with the temperature at which cupellation is carried on. Pure silver loses relatively much more than gold, but the loss in either is diminished by an addition of the other metal. The concentration of precious metal in the litharge increases as the concentration in the lead increases, but little work has been published connccting the two. If all other conditions remain the same the actual total loss increases, but the percentage loss diminishes, with an increase in the weight of precious metal treated. The results of an immense number of experiments have been published at various times- during the past hundred years giving the actual or the percentage losses suffered under various conditions of cupellation, but the data are widely scattered and few attempts have been made to correlate them, so that no definite law has heretofore been shown to exist

Jan 1, 1916

By Walter H. Bucher

THIS symposium is designed to lay the basis for a general discussion of the place of geophysics in the training of geologists. As there is danger that in the ensuing debate individual interests may be given emphasis out of proportion to their place, we shall do well to view the whole field of geological inquiry in order to see the problem in true perspective. THE NATURE OF GEOLOGICAL INQUIRY "Basic" and "Complex" Sciences It is convenient to divide all science into two major divisions, the basic and the complex sciences. The basic sciences separate out from reality such entities as "substances" and "movements," describe their behavior in terms of arbitrary units of measurement and derive from them by progressive abstractions concepts and patterns of behavior that exist between them, so-called general "laws" and "properties" of nature. The complex sciences, on the other hand, deal, with little or no abstraction, with those objects of reality that are accessible to man in the atmosphere, the hydrosphere, the lithosphere and the biosphere.† Their work comprises two types of inquiry. One is concerned with abstractions to the extent of dealing with types rather than individuals-that is, with such things as plants, animals, protoplasm; clouds, streams, glaciers; volcanoes and mountain ranges. It comprises the search for general properties and patterns of behavior or "laws" that characterize the objects and their reactions to each other. These properties and laws apply always, everywhere. They are independent of the stream of time. We may call the results of this sort of inquiry timeless knowledge. The other type of inquiry is concerned with the objects themselves-that is, with this animal and that plant; this river system and that mountain chain; this glacier and that valley. Like all concrete objects in nature, they are subject to change with the passage of time, especially when it is measured in years, centuries, eons. The characteristics by which we recognize them -indeed, their very existence are dependent on their position at this point in the stream of time. This we may call time-bound knowledge. The so-called descriptive sciences are all bound to the past of which the objects of their study are the product and through which alone their present properties can be understood. They are historical sciences. This obvious fact is easily overlooked, which leads to serious misunderstanding, as we shall see later. Dynamic Geology With this broad picture in mind, let us now examine the nature of geological inquiry, defining, for the purposes of this discussion, geology as the science of rocks. Air is not a rock; water is. Meteorology and climatology are, correspondingly, gen-

Jan 1, 1941

By Clarence Fenner

THE manufacture of optical glass is a process that demands careful regulation and control at all stages in order that satisfactory results may be obtained. The product, to serve its purpose, must meet stringent requirements, which can be assured only by careful procedure in manufacture. During the greater part of the time that a pot of glass is in the furnace, temperatures should be kept within certain rather narrow limits; a departure on either side is likely to be detrimental to the glass and may result in total loss. If the temperature during melting and fining be low, the melt is likely not to fine properly and the glass will contain quantities of bubbles, or "seed," or it may become milky and unfit for use; too high a temperature, on the other hand, is severe on the pot and may cause it to leak or cast stones, or the increased solution of pot material in the melt may acid to the color of the glass and decrease its transmission. Moreover, variations in the working temperature will mean variations in the amount of selective volatilization and, consequently, variations in optical properties from pot to pot. Furthermore, in the closing stages of furnace treatment, the melt is cooled until a certain degree of stiffness is attained, when the pot is withdrawn. The quality of the glass-its freedom from striae and bubbles-will depend in large measure on whether the temperature to which cooling has been carried is suitable. For each type of glass there is a narrowly restricted range of temperature to which each pot of the given type should be cooled before withdrawal. A quick and reliable method of measuring temperatures is, therefore, of the first importance. In the optical-glass work conducted by the staff of the Geophysical Laboratory during the period of the war, much attention was given to the clatter of determining what methods would meet the requirements. This article will deal with these investigations and with the application of the results to actual practice at various plants. At the. time that the work of the Geophysical Laboratory was begun at the Bausch & Lomb plant, each melting furnace was equipped with

Jan 7, 1919

By Paul H. Lu

This report by the Bureau of Mines, U.S. Department of the Interior, presents several practical and inexpensive types of rock mechanics instrumentation for ground control around longwall panels. Application of these critical parameters, determined by this instrumentation, to the design and modification of rational longwall-mining systems is also discussed. In order to design or select an optimum mine structure or system, realistic and precise values of the design parameters must be determined in operating mines by measuring (1) existing ground stresses, (2) mining induced load transfer, and (3) strata movements as well as deformation moduli and rock strengths. Based on these parameters, rational and realistic criteria for mine design can be established by conducting case studies. It was found that several basic design parameters can be easily measured or determined in situ with simple, inexpensive, and practical instruments such as hydraulic borehole pressure cells, automatic recording convergence meters, automatic recording multiple-anchor-point extensometers, and hydraulic pressure recorders.

Jan 1, 1982

By R. W. Nelson

Methods for determining permeability presented by W. D. Kruger3 in a paper entitled "Determining Areal Permeability Distribution by Calculation" have considerable merit. They can be expected to contribute significantly to analysis of flow in heterogeneous systems. Some rather subtle yet important conditions must be met, however, to assure that the computed permeabilities are correct. The conditions which insure a unique permeability distribution may have been overlooked in the method as proposed and presented in the subject paper. The subtlety of the special requirements may permit good agreement between computed and measured pressures in the reservoir; but the computed permeability may still be in error. The general theory and discussion of the requirements for a unique determination of the permeability distribution are presented elsewhere in more detail.7'8 Accordingly, only major features will be presented here in the notation of Kruger. GENERAL DESCRIPTION OF REQUIREMENTS A brief mention of the route to be followed in showing the special requirements may be helpful. The equation to be solved is a quasilinear, first-order, partial differential equation in the unknown permeability. This equation can be solved through an extension of Lagrange's method by reduction to a system of subsidiary ordinary differential equations. Through consideration of the identity of one of the Lagrange subsidiary differential equations with the stream function, a special interrelationship can be shown. The interrelationship has special significance with respect to the boundary condition. If the boundary function satisfies part of the subsidiary differential equation, no unique solution for the permeability distribution exists. In the physical problem this requirement for uniqueness indicates that the permeability measurements used as a boundary condition can not be along a stream tube. The boundary condition must be along a line, or series of lines, which completely traverse the region and pass through every stream tube.

By Kandalla Ravindranath, C. C. Patel

Studies of the adsorption of dialkyldithiocarbamates at the surfaces of galena and sphalerite have shown that characteristic contact angles are obtained at galena surfaces in the 7-10 pH range, whereas lower angles are obtained at unactivated sphalerite surfaces even at pH 71 Further, the angles at sphalerite surfaces progressively decrease with increase in pH. However, when sphalerite is activated with cupric sulfate, characteristic contact angles are obtained at pH 7 and beyond. This shows that galena and sphalerite can be selectively floated with dithiocarbamate collectors at pH 7 and beyond. Experimental Materials Ore: The lead-zinc ore for the present study was obtained through the courtesy of the Geological Survey of India from Dariba, Udaipur, Rajasthan, India. The average ore analyzed 15.5% lead, 11.6% zinc, 6.7% iron, 15.6% sulfur and 36.6% acid insolubles. The ore was crushed in a Denver laboratory rod mill and sieved in a Denver automatic sieve shaker to obtain a -200- to +250-mesh (Tyler standard) fraction. This particular size was chosen because it was conducive to good liberation of sulfide minerals, both from one another and from gangue minerals. Collectors: Dimethyl, diethyl, diisopropyl and diisobutyl dithiocarbamates were prepared and purified by the methods described by Klopping and Van der Kerk.2 A freshly prepared 0.03% dithiocarbamate solution in distilled water was used for flotation studies. Frother: A 0.03% solution of pine oil in ethyl alcohol was employed. Activator: 7.3 g of cupric sulfate pentahydrate were dissolved in 1 1 of water and used for the activation of sphalerite. Depressant: 16.0 g of zinc sulfate heptahydrate were dissolved in 1 1 of water and used for the depression of sphalerite.

Jan 1, 1972

By Junnosuke Yamamoto

Substituting sodium hydroxide for sodium carbonate as a binder in a glass batch yields harder pellets with a lower melting point. This paper explores the degree of NaOH substitution that is feasible, and compares pellet hardness, and amount of dusting with the degree of NaOH substitution. The effects of the the amount of soluble silicate in the pellet and residual hydroxide concentration in the pellet on pellet hardness are also studied.

Jan 1, 1977

By G. E. Keller, G. D. Coe

Several methods have been devised for rapid determination of sulfur in coal using a high-temperature combustion furnace. The fundamental principles of the various methods are similar but the techniques vary widely. The method described herein is no different in principle from some of its predecessors but varies considerably in technique. Originally devised to overcome the low-accuracy criticism leveled against the others, the tube-furnace method has proved successful for limited applications. Work is being done to widen the applicability of the technique. Subsequent to the work of A. Vita1 in 1920, a number of investigators have published data dealing with the rapid determination of sulfur in coal using a high-temperature combustion furnace.2-5 These, together with several unpublished methods, involve wide differences in technique although they are all similar in principle. Investigation of typical details of procedure showed that poor precision or accuracy could be attributed to one or more of the following: 1) inadequate quantity of sample to be representative, 2) a delivery tube temperature too low to confine condensation to a washable area of the tube, 3) no provision for back washing the delivery tube, 4) incomplete absorption of the sulfur compounds due to inadequate bubbler, and 5) the false assumption that all of the sulfur is evolved as sulfur dixoide. The method herein discussed is no different in principle from some of its predecessors; the differences are in technique. Although the method is rapid—a determination can be completed in 5 min— accuracy has riot been sacrificed in order to achieve speed. MATERIALS AND EXPERIMENTAL WORK Fig. 1 shows the arrangement of the equipment. A metered volume of oxygen is passed through calcium chloride for removal of moisture, then through Ascarite for removal of carbon dioxide, and thence through a glass tee to the feed end of the combustion tube. Connected to the side arm of the glass tee is a rubber tube that is closed with a pinch clamp during combustion of a sample. The products of combustion are expelled through a Vycor bubbler, the end of which is submerged 3 cm below the surface of a 1 pct hydrogen peroxide solution contained in a 300 ml high-form beaker. At the completion of the 4-min combustion period the contents of the beaker are titrated to a yellow end point, using a methyl red indicator, with 0.05 N sodium hydroxide (or sodium tetraborate). The pinch clamp on the tube leading from the tee in the oxygen line is then opened and mouth suction applied to draw the hydrogen peroxide up into the bubbler past the ell, almost to the rubber tube connecting the bubbler to the combustion tube. This washing of the bubbler is repeated until no further acid reaction with the indicator is obtained. The hydrogen peroxide-sul-furic acid solution is then titrated to the final yellow end point. Test work conducted at the Robena Laboratory disclosed the following critical conditions that had important bearing on the precision of the method: Weight of Sample: Several series of tests wherein the sample weight ranged from 0.1 to 0.5 g of -60 mesh coal showed that the lowest variance (standard deviation squared) resulted from the use of 0.5-g samples; the variance was slightly greater when 0.3-g samples were used, and with less than a 0.3-g sample weight the variance increased rapidly with decrease in weight. Although the use of a 0.5-g sample invariably resulted in a very slight explosion as soon as the sample entered the hot zone of the combustion tube, this did not detract from the precision of the method. Temperatures: Mott and Wilkinson5 found that a combination of low temperature (1250°C) and low oxygen flow rate (less than 700 ml per min) tended to give high results due to formation of oxides of nitrogen. Although the method herein employs a much higher oxygen rate than 700 ml per min, as an additional precaution to assure accurate results, 1315°C (2400° F) is recommended as the most desirable furnace temperature. The temperature of the elbow of the bubbler should be at least 75°C to minimize condensation

Jan 1, 1961

By Donald L. Birkimer

GENERAL INTRODUCTION To paraphrase comments made by Black and Hoek(1) on the status of rock mechanics, the general methods of applied science related to rock mechanics are: a. Observe the phenomena of nature as they occur and, wherever possible, quantify the observations. b. Propound a model or theory to explain the phenomena observed. c. Test and develop the theory by further experimentation in the laboratory and in the field. d. Use the theory developed to predict behavior in similar or extended circumstances. e. Insure by measured experiment and observation that the predictions made are valid, or that deviations from the predicted behavior can be accounted for. f. Modify the theory and practice as necessary, and continue the process until more general laws can be formulated and applied, with a useful degree of confidence, to practical problems. This paper will present an infant concept. It will, in fact, propound a possibly useful theory to help explain commonly observed phenomena. It will test and develop the theory for a material similar in nature to some rocks. It will be used to predict behavior in the extended circumstances of a

Jan 1, 1971

By John Birkinbine

An item of considerable importance to the producers of pig-iron is the disposition of the slag or cinder from the blast-furnace; and various plans have been adopted at different works to care for the rapid accumulation of this generally waste material. The charge per ton of iron made which must be allowed for the care of cinder is sufficient in times of business depression to give plants having facilities for disposing of their slags an advantage over others less favorably arranged, and to allow iron to be produced profitably in the one case and prevent a profit in the other. The varied methods employed and the means of conveyance utilized need not be detailed. It is sufficient to say that the large outputs of American blast-furnaces, and consequent rapidly augmenting dump-piles, have brought into general favor the use of cars carrying the slag in a liquid condition. The advantages of this method are the prompt removal of the slag, the reduced space occupied by the dump-piles, and the facility of converting the slag into such forms for use as may be desired. The progress in iron-manufactlire is also marked by a more general adoption of methods by which molten metal is carried in vessels away from the point of its production; and, anticipating the prospective advance in pig-iron manufacture, it does not seem unreasonable to prophesy the early abolition of casting-houses at blastfurnaces, particularly where several are grouped together; or the casting of steel ingots away from the converters or furnaces. In some large blast-furnace plants, the iron is carried molten from the blast-furnaces to the converters or other furnaces. Even where it is cast into pigs, casting-sheds removed from the immediate vicinity of the furnace-stack would, perhaps, be superior to casting in beds in front of the furnaces. The idea of casting-sheds appears to present the following advantages : 1st. The equipment of boilers, hot-ovens, and blowing-machinery could be closely grouped around the blast-furnace stacks, permitting

Jan 1, 1887

By George W. Becker, Blair R. Benner, Ronald J. Roman

A computer model for the leaching of oxide copper heaps is developed and verified in laboratory tests. The model can be used to scale-up laboratory test data and to simulate the results of various operating philosophies on heap leaching. The model is applicable to leaching processes where the rate of leaching is controlled by a deficiency of reactant or diffusion of a reactant through the leached rock. Several examples are presented showing the sensitivity of the recovery vs. time curve to the variables in leaching.

Jan 1, 1975

By C. A. Stetefeldt

Jan 1, 1892

By D’Arcy A. Shock

In this year's review, the concept of solution mining has been expanded to include total solution as well as the technology of leaching, or partial solution methods. Leaching methods continue to make strides in the processing of metallic minerals, particularly in copper and uranium production. No quantitative data are available on the increase of leach operations; however, it is known that there were more systems installed in 1969 and that the estimated 15% of U.S. domestic production of copper produced in 1968 was by leach methods.1 While the number of publications appearing during the year were few,2,3 there were special sessions in this field at the AIME Annual Meeting and SME Fall Meeting in 1969 and more scheduled for these meetings in 1970. Significant areas that should be mentioned are: the continuing interest in bacteria to convert sulfide sulfur to acid thus reducing reagent costs in both copper and uranium sulfide ores, the exploration of leaching agents other than common mineral acids or alkaline solutions,4,5 kinetic studies of leach mechanisms and the development of microfractures for increased leach solution penetration by use of chemical or atomic explosives.6,7

Jan 1, 1970

By Bruce A. Kennedy

SME hopes to publish its first separate volume of Mining Exploration Transactions later this year. The reason for this separate publication was stated in "Rock in the BOX," December 1969 [ ], p. 14, as follows: "Because of the great upsurge in mineral exploration (during) the last few years and the fragmentation and narrow specialization of the earth sciences into a great many fields not directly related to exploration, many explorationists feel that a need for a special journal devoted to mineral exploration now exists." To summarize the history behind this change in publication policy of the Mining and Exploration Division, we go back to 1968 when a small group of M&E Division members advocated the establishment of an entirely separate journal devoted specifically to exploration. S. Parker Gay Jr. was appointed chairman of an ad hoc committee to investigate the feelings of the other Division members toward such a journal. Approximately one thousand questionnaires were sent out and the returns showed an extremely favorable reaction. Gay reported the results of his survey to the M&E Division Executive Committee Meeting in Salt Lake City in September 1969. These results were also published in the December 1969 issue of [ ].

Jan 1, 1970

By J. N. Ong, J. P. Ratledge, J. H. Boyce

SINCE German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding. Geology and Mineral Association is Complex The Tsumeb mine lies near the northern boundary of South West Africa at an altitude of 4200 ft. The village of Tsumeb is 335 air miles northeast of Wal-vis Bay, territorial port of entry. The orebody is a hydrothermal replacement deposit associated with an irregular intrusion of aplite cutting folded pre-Cambrian dolomite beds. In plan the deposit is a lens of 250x600 ft maximum dimensions. In section the orebody dips 55" south from the surface to 2000 ft, below which there is a reversal in dip to 75" north. Mineralization is localized in the aplite and in the adjoining brecciated dolomite. In the upper levels the ore is largely confined to a single lens, but below the 1890 level massive sulphide ore forms north and south lenses that partially enclose a pipelike body of medium to low grade disseminated ore, part of which is of too poor a grade to mine. Drilling below the 24th, or bottom level, has disclosed that a high percentage of the mineralization from the 3000 to 3300-ft horizons is comprised of copper and lead oxides. The deep oxidation may be local, since it appears due to circulating waters in a major fault cutting the orebody. Tsumeb ranks as one of the highest grade base metal deposits in the world. It is geologically and mineralogically famous for 41 copper, lead, zinc, vanadium, and germanium ore minerals, but its complex mineral assemblage is not attractive to metallurgists. In addition, there is a gradual change in oxidation intensity from the upper levels to the lowest level now operating, which is the 24th. This is well illustrated by the copper minerals. In the upper levels malachite and azurite are predominant, in the intermediate levels chalcocite, and in the lower levels tennantite. Throughout the mine there are sufficient heavy metal soluble salts to activate zinc, and large amounts of depressants are required even for so-called clean sulphide ores. When the same sulphide ore is exposed to prolonged oxidation aboveground, as was the case with the dump ores, reagent requirements become fantastic. Plant Construction First staff members arrived at Tsumeb in March 1947, and by May essential services had been restored and mine unwatering began. In 2 1/2 months company employees built a temporary jig and sorting plant for treating existing dumps to provide a saleable product during high metal prices. Meanwhile, concentrator design and construction was contracted to a South African firm, with subcon-

Jan 1, 1956

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated' that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication' in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By N. H. MacMillan, W. M. Mularie, R. E. Jackson, A. R. C. Westwood

The initial results of a study of the environment-sensitive microhardness and diamond rotary drilling behavior of granite and its constituent minerals quartz and feldspar (microcline)1 have established that many similarities exist between the environment-sensitive mechanical (chemomechanical) behavior of these materials and that of the simpler solids such as periclase, soda-lime glass, and alumina4 studied previously, at least as far as n-alcohol (straight-chain alcohol) environments are concerned. The results of this study (hereafter designated study I) also suggested that the rate of drilling of granite in these environments is controlled by the chemomechanical behavior of its quartz constituent, and is greatest in those environments which impart a zero l-potential to this phase, thereby maximizing its hardness. Now, cationic surface-active species strongly influence the l-potentials of silicate minerals. For this reason they are widely used in mineral separation operations. In particular, dodecyl trimethyl ammonium bromide (DTAB) was found in study I to produce f 0 for quartz at a concentration in water of 107 to 10-4 moles per 1. Accordingly, the influence of dilute aqueous solutions of this surfactant on the drilling behavior of granite also was examined in study I. This revealed that granite could be drilled three to four times faster in 10-° molar aqueous DTAB than in water, and confirmed by experiment the suggestion that granite is most effectively drilled with a diamond core bit in environments which impart a zero l-potential to quartz. According to O'Connor and Buchanan' however, the isoelectric point for quartz in aqueous DTAB solutions occurs at a concentration of .•.•2 x 10-° moles per 1, rather than [101 to 10-1] moles per 1. To confirm the results of study I, therefore, a more comprehensive investigation of the [ ]-potentials of quartz, microcline, and Westerly granite in aqueous DTAB environments has now been undertaken. At the same time an examination has been made of one of the basic assumptions of the current conceptual understanding of chemomechanical effects. In this view, although hardness changes occur essentially instantaneously following wetting of the solid, they are confined to a surface layer at most a few micrometers (µm) deep. Hence, to maximize the influence of chemomechanical effects on bit penetration rate only shallow cuts should be taken. Practical penetration rates are then obtained by increasing bit rotation speed. Experimental l-potentials were determined by the streaming potential technique using an automated rapid-cycling apparatus recently developed by Martin Marietta Laboratory from a design by Somasundaran and Kulkarni. The drilling studies employed 3.2-mm-OD 120-grit diamond-loaded core bits with a wall thickness of ~0.7 mm, and bit rotation speeds of 2200 and 25,000 rpm. The load applied to the bit was independent of the depth drilled in both cases. The 2200 rpm measurements employed the same drill press and puddle drilling technique as used in study I. The higher rotation speed was obtained using a water-driven dental turbine drill. In the case, the surface active fluid was pumped down the axis of the bit to ensure efficient wetting and flushing of the drilling debris from the hole. In both cases drilling rate was measured by the parameter D(200), defined as the average rate of bit penetration during the interval from 150 to 250 sec after drilling commenced.

Jan 1, 1976

By S. C. Termes, R. L. Wilfong

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using cross-linked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganite, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The imlnodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pyrolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethanolamine derivative. The separation of hematite from quartz by selective flocculation with chelating crosslinked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dispersing agent.

Jan 1, 1984

By T. J. O’Neil, S. J. Kirk

In 1978, a multidisciplinary team from the University of Arizona, the Mines Project Group, conducted a study to examine reclamation alternatives for a proposed open-pit copper mine. The cost of a waste dumping plan designed by a mining consulting firm was determined as well as the cost of dumping configuration prepared by the Mines Project Group. The latter dumps were designed to be more socially acceptable and aesthetically pleasing, in addition to serving more creative end land uses than the dumps designed by the mining consultant. One dump configuration designed by the interdisciplinary team was the least expensive plan of all the alternatives considered.

Jan 1, 1984