Search Documents

By John Ziats

This chapter covers the drawing requirements for the design of a comminution plant.

Jan 1, 1982

By David Baker

In a paper presented to the American Institute of Mining Engineers, September, 1904, entitled uImprovements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low— thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace-gases, unequal reduction, slips, scaffolds, irregular cutting of the inwall, "of" iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from succeesively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very

Jan 1, 1907

By R. W. Kobler, D. A. Dahlstrom

Since the development of the pelletizing process in the fifties for relatively high purity pellets from low grade taconites, there have been several distinctive changes in filter construction for the dewatering step preceding balling. In the original large pilot plant run by Reserve Mining Co. in Babbitt, MN, the disk type filter employing agitation (Agidisc filter) was selected as the most economical. Size was limited to 2.1 m (6 ft, 9 in.) in diameter. The second generation occurred in the sixties with a jump to 2.70 m (8 ft, 10 in.) in diameter to reduce capital costs per annual ton of pellet. In the early seventies, the third generation was the steam drying disk filter which became necessary to achieve balling moistures with specific surface areas of 2200 cm2/g to as high as 3800 cm2/g caused by finer grinding to obtain higher purities. Finally, the fourth generation has recently been developed to reduce maintenance costs and further improve hydraulics to ensure minimum moisture contents.

Jan 1, 1980

By C. W. Bildt

During many years of service in the iron and steel industry I have frequently found, as have also many other engineers, that the common devices used for feeding coal into gas-producers are not what they ought to be in order to secure the best economy. The hopper-and-cone so generally used is familiar to all, and a brief study of its action will surely satisfy everybody that this device has several serious faults. In the first place, the charging is intermittent, and depends entirely upon an attendant. When the hopper is frequently emptied, it may work fairly well, but even then it suddeinly discharges into the hot producers a large body of coal, which is often violently converted into gas that rushes into the furnace, and, as the damper for the combustion-air cannot be regulated every time the producer is charged, there will be an excess of gas, which goes up the chimney unburned. Between the chargings the quantity of gas generated decreases, and there will often be an excess of air in the furnace,

Jan 1, 1899

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen: - I herewith present a report of some. of the more important activities of the Institute for the year of 1922. The outstanding feature of the year is the optimism felt by our members despite the continued depression in the mining industry. January 1, 1921, found many of our members out of employment or drifting into other industries to tide them over the depression, but almost universally the feeling has been that this was but a temporary condition and that sooner or later the necessary production of raw materials would enable these members to return to their former activities and renew their participation in Institute affairs. As the year passed conditions improved and, before it ended, many had found employment in their previous occupations. Bearing in mind that this depression has been very real, we have reason to be well satisfied with the work that the Institute has been able to do. The loss of members through inability to pay, dues has been large, and income has been correspondingly reduced, but it proved to be materially in excess of that anticipated early in the year, so that a substantial and unanticipated balance was carried forward toward the activities of 1923. PUBLICATIONS Following the example of other technical societies, and to conserve our resources, no Year Book was published in 1922. The lack of an up-to-date membership list for the use of our members was regrettable, but the saving of $5000 proved to be worth while. During the year, Volumes LXV, LXVI, and LXVII were printed and sent to members. These volumes were composed largely of the papers of 1920 and 1921, publication of which had been delayed partly through lack of funds and partly for the purpose of segregating into volumes those papers dealing with the same general subject. The segregation of papers had been suggested by a number of members who had advised that they were not primarily interested in all subjects

Jan 1, 1925

By C. A. Wright

Since the adoption by the U. S. Bureau of Standards several years ago of specifications for standard 100- and 200-mesh sieves, frequent requests have been received that this Bureau test and certify sieves of other sizes than these. With a view to the adoption of a series of standard testing sieves which might be of use to all industries making fineness tests, this Bureau for two years has been studying the question of such a standard screen scale. Various scales that have been proposed were considered, and information was sought of representative firms in the various industries interested as to their requirements. Manufacturers of sieves have also been consulted as to the desirability of different screen scales and the practicability of their manufacture. As a result of this study of the question, a conference was called at the Bureau of Standards, Apr. 20, 1916, of representatives of various committees of the American Society for Testing Materials, American Society of Civil Engineers, American Institute of Mining Engineers, American Foundrymen's Association, Mining and Metallurgical Society of America, American Water Works Association, American Institute of Metals and the American Spice Trade Association; also representatives of the Committee of Revision of the U. S. Pharmacopæia, the U. S. Geological Survey, the U. S. Bureau of Mines, the U. S. Office of Public Roads and Rural Engineering, the U. S. Office of Grain Standardization and the U. S. Bureau of Standards; also representatives of a number of private firms engaged in industries in which sieves are used, such as the glass, the drug milling, the abrasive, the asphalt, the mining, the spice, the chemical, and the graphite industries; also representatives of the firms in this country manufacturing wire cloth and sieves. This Conference, after considering the various screen scales either proposed or now in use, adopted as a Standard Screen Scale that given in Table 1, and recommends that it be adopted generally by scientific,

Jan 1, 1918

By J. T. Richards

ELASTIC constants, including E-modulus, G-modulus, Poisson's ratio, and compressibility, are affected by temperature, but not necessarily to the same degree nor in the same direction. Theoretical expressions relating the temperature coefficients for the various elastic constants have been introduced by Gruneisen. In considering the thermoelastic characteristics

Jan 1, 1955

By Massimo Guarascio

Computer data processing and ore reserve evaluation techniques, mainly based on geostatistical methodologies, have been developed at Agip Mining Division with the assistance of the Department of Mining Engineering of the University of Rome. A number of computer programs are available when facing problems such as optimization of sampling patterns, minable reserve estimation, grade control of output, and so on. In the present paper, the aims and the criteria followed in developing these programs are discussed. Some recent examples of application are also cited.

Jan 1, 1977

By Victor Phillips

Cyclone thickeners have emerged from the development stage and now can be accepted as useful tools for the recovery of fine coal from a preparation plant circulating water. As primary thickeners in a closed water circuit operation, their advantages over conventional thickening methods are twofold-the lower initial investment and reduced area requirements.

Jan 8, 1951

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual model fitting is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. Many interactive methods are described, which are adapted to modeling semivariogram in one-, two-, or three- dimensional environments.

Jan 1, 1985

By W. W. Dudley

Inflow of ground water is an important engineering and safety consideration during construction of large openings underground. The initial step in predicting groundwater inflow involves hydraulic tests in exploratory drill holes. Zones within the area of interest are isolated in the drill hole by inflatable packers and are tested by measuring the water level responses to applied hydraulic stresses. These responses may then be translated into significant hydraulic characteristics of the tested rocks such as transmissivity, hydraulic conductivity, hydraulic potential, and storage coefficient by using a type-curve solution. Once the geometry and necessary hydraulic characteristics have been determined for the rock in the vicinity of the proposed opening, a model can be developed using certain assumptions that will lend itself to treatment with available mathematical methods. The mathematical method applied to the model considers conditions of partial penetration and nonsteady-state, leakyartesian, constant-drawdown discharge of ground water. A type-curve solution results in a curve that gives the variation of discharge (inflow) with time. This technique of predicting ground-water inflow has been used in planning construction of cylindrical chambers for use in underground nuclear experiments by the U.S. Atomic Energy Commission. These chambers have been constructed in low-permeability rocks at depths as much as 6000 ft and under hydraulic heads of thousands of feet.

Jan 1, 1973

By Edward J. Bagnall

The major raw material feed properties of size distribution and chemistry are examined in relation to their effect on sinter operating conditions, plant productivity, sinter physical quality, reduction- degradation characteristics and sinter texture and mineralogy. The resultant physiochemical properties of these sinters are related to their behaviour in subsequent ironmaking operations.

Jan 1, 1977

By M. E. Kukura, L. G. Stevens

As described in a previous presentation and in various patents, the Minerals Sciences Div. of UOP, Inc., has developed a modified reduction roast ammonia leach process for nickel laterites. This process gave considerable improvement in extraction over the conventional Caron approach as practiced in Cuba, Australia, and the Philippines. This greatly improved response was obtained with a wide variety of ores. This paper describes the pilot plant flowsheet and reviews the design features unique to the UOP process. Operating results from pilot plant campaigns are compared with bench scale results. Operating problems and their solutions are also discussed.

Jan 1, 1976

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1980

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 12, 1979

By F. C. Blake

THE test of the English cupellation furnace should be so supported that the cupeller can change readily the elevation of the test, and at the same time watch the litharge channel. It is also important to raise or lower either side, independently of the other, in me of uneven wear of the side walls or of the breast. If the refined silver is poured from the test, it is much better to control the lowering of the test from the front than to raise the back by screws or a lever. In order to enable the cupeller to manipulate the test with one hand, when the litharge is running, and to pour the refined silver from the test without aid, I have altered the common support to the test, as shown in the accompanying drawing. The common method of supporting the test is by four screws, working in cross-bar nuts beneath the test. The points of the screws set, into the test plate upon which the test rests. These screws are usually worked by pounding or pulling upon the heads, which may be either small pulleys or straight bars, as shown on the back screws in the drawing. The screws are also worked by turning a crank, which is

Jan 1, 1882

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength- temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates.

Jan 8, 1953

By H. M. Chance

In the early part of 1893, I had occasion to make for the owners a professional examination of the Rich Patch tract; and, with their permission, I present in this paper, omitting the commercial portions of my report, those portions which may be valuable to future students of that region. Location, Topography And Geology. The Rich Patch tract comprises about 9000 acres, located about 3 miles west of Low Moor, on the Chesapeake and Ohio Railway, in Alleghany county, Va., and immediately adjoining the Low Moor property. In shape the tract is roughly quadrangular, being about 3 miles broad in a northerly and southerly direction, by about 6 miles long from east to West. Potts creek and Jackson river run along its northern boundary. It is drained by Hayes Gap run, Mill branch and Laurel creek, which flour north into Potts creek, and by Karnes creek, which flows northeasterly through the Low Moor property into Jackson river. The topography of the tract is shown by the accompanying map (Fig. I), and need not be described here. The valleys are cut down from 1000 to 1500 feet below the mountain summits, which generally reach an altitude of about 3000 feet above tide. The geological structure of the district is indicated by the geological cross-sections shown in Figs. 2 and 3. These sections show that the formations underlying the property extend from the Lower Silurian lin~estones up to the Devonian slates, including the numbers of the Paleozoic system of rocks as defined by the geological surveys of Virginia, Pennsylvania and New York, from No. 11. to No. VIII. • No. IX. Old Red Sandstone, No. VIII. Slates and Shales, Devoman-

Jan 1, 1900

By S. Terry, J. G. Munro

A unique feature of the recently dedicated pelletizing complex of Hamersley Iron Pty. Ltd. is the dry grinding circuit for the iron ore fines. This facility, located at Dampier, some 800 miles north of Perth, Western Australia, has a rated annual capacity of 2 million tpy of iron ore pellets. The Mt. Tom Price orebody, which supplies the pelletizing plant, is a massive deposit of high-grade hematite containing an estimated 500 million tons of ore averaging 64% iron. The main impurities are ferruginous shales that occur in bands of varying widths in the orebody. An average analysis shows 4.4% SiO2, 2.0% A12O3, 0.05% P and 1.8% LOI.

Jan 5, 1968

By Harry Bapty

LONGHOLE drilling with a heavy type percussion Leyner drill, jointed steel rods, and a tungsten carbide insert bit was investigated while drilling and working a quartz barite brecciated rock. Procedure and practice were developed and its suitability for tackling pillar and sill recovery proven and extended to regular stoping at Torbrit. Torbrit, as the name implies, is a contraction of the Toric property and the Britannia Mining & Smelting Co. Ltd., the former owners. This silver property, with minor amounts of lead, zinc, and rarer sulphides of little or no economic value, was discovered in 1916 from an outcrop in the Kitsault River, 18 miles north of Alice Arm Post Office, in the Portland Canal Mining District, B. C.

Jan 11, 1954