Search Documents

Jan 1, 1906

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay binders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County.

Jan 1, 1978

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described.

Jan 11, 1950

By Waldemar F. Dietrich

Mineral fillers are relatively inert chemically under the conditions of use but have physical properties* that modify those of the materials in which they are incorporated. The mineral fillers considered in this article are asbestos, barite, clays, diatomite, crushed limestone, limestone whiting and lime, mica, silica, talc and soapstone, and pyrophyllite. Slate and stone, other than limestone and its derivatives, are excluded because, even though used in large quantities, they are exceptionally low-cost materials generally produced close to the area where they are used.

Jan 8, 1959

By A. J. Naldrett, N. T. Arndt

In Archean greenstone belts, ultramafic lavas occur interbanded with basalts, commonly at the base of volcanic-sedimentary cycles. The lavas form part of a recently recognized extrusive rock series, the magnesian series, in which liquid compositions range from peridotitic (33 wt-% MgO) to basaltic (8 wt-% MgO). Rocks of this series occur as peridote, pyroxenite and magnesian basalt flows, and intrusive/extrusive bodies of dunite (49 wt-% MgO) grading outwards into a peridotitic marginal zone. The nickel sulfide deposits are of two main types: (1) basal accumulations of massive and disseminated pyrrhotite + pentlandite associated with some of the thickest and most magnesian (<40 wt-% MgO) of the peridotite flows, and (2) widespread zones of disseminated sulfides in the dunite lenses. Massive sulfide segregations may occasionally occur within the dunites.

Jan 1, 1977

By Ingemar Marklund

This presentation deals with the conditions at IKAB’s mine in Malmberget but also pertains to underground mining in general. GEOLOGY The Malnberget iron ore field is of pre-cambrian age. The wallrock consists of leptites, gneisses and granites, most of them being recrystallized acid and inter- mediate volcanics. The ore-field is strongly folded, with the folding axes plunging to the south. The original orebed is divided into about 20 different orebodies with a strong variation in dip and form. The ore is mainly magnetite. About 1046 of the ore area consists of hematite ore. The phosphorous content is in average 0,8% and the ore is rather course grained. Fig 1. BACKGROUND At LKAB1s mine in Malmberget the sub- level caving method is the main method of mining. Experiments with vein-mining and sub-level stoping are also underway. The present system of mining is already strictly tied up in investments and infrastructure involved in the mining. Fig 2.

Jan 1, 1981

By K. Robert Dorman, F. Michael Jenkins

The occurrence of rock bursts in deep metal/nonmetal mines presents a major hazard to their safe and economical operation. As part of a Bureau of Mines program to reduce rock bursts in deep vein mining, a project was conducted in the Coeur d&apos;Alene Mining District of Idaho to evaluate and demonstrate the mining of a destressed sill pillar using undercut-and-fill methods. A 50-ft sill pillar in a burst-prone area was preconditioned by drilling and blasting vertical holes in the ore. After raises were driven through the destressed pillar to the level above, it was mined by the undercut-and-fill method. The conclusion from this demonstration is that the combination of ore preconditioning and underhand mining resulted in greatly improved rock burst and ground control, allowing safe and efficient mining of a potentially hazardous, burst-prone pillar.

Jan 1, 1984

By David Mandolesi

An examination has been made of the structures of strand cast blooms and the rails rolled from them; this paper details the characteristics of these typical structures. Results of mechanical testing data show that this product compares with rails processed from conventional ingot steel. Improvement in processing yields and surface quality standards are also briefly discussed.

Jan 1, 1972

Jan 1, 1932

By Gerald Edmunds, R. K. Waring, E. A. Anderson

Brass is liable to failure under the combined influence of stress, certain corrosion media, and time, a phenomenon commonly termed season cracking or stress-corrosion cracking. The consequences of this are serious in applications of brass generally, including the important field of cartridge cases. Cartridge cases (70 Cu: 30 Zn) that fail from this cause may allow the escape of gas from the gun breech, a hazard to the shooter, and may not eject, thus temporarily putting the gun out of action. In loaded cartridge cases, the stress present is partly residual from the, drawing and necking operations and partly applied by the insertion of the projectile. Ammonia, present as a decomposition product of smokeless powder, air and moisture constitute corrosive media. The prevalence of season cracking has been reduced considerably, but not eliminated, during the past quarter of a century by low-temperature annealing to relieve stresses residual from fabrication, a method suggested by Diegel 38 yr. ago(I).2

Jan 1, 1945

By C. McCulloch

OPEN-PIT mining of coal is relatively a recent innovation; men still active in the industry can trace its development. Re- viewing the growth of operations from the original horse-drawn scrapers, through the various stages of power equipment to the huge strip- ping shovels of today, one also notes changes in the methods of what the coal man calls preparation at the face. We really should not call it face preparation because, in contrast to underground mining, a face does not exist in strip mining. Further, preparation of the coal for market at the loading point has already, in but a few years, become largely of historic interest only and modern mines as well as old mines recently modernized rely almost entirely on separate and elaborate preparation plants to produce marketable coal. This practice was not voluntarily adopted by the producer but was forced upon him by the inadequacy of previous

Jan 1, 1939

By Carl Zapffe

The manganese ore reserves of Lake Superior, because of their location and nature, have recently achieved a rnarked degree of importance as compared with the world&apos;s manganese reserves. To appreciate fully the significance and the adequacy of this reserve, one should understand how such ores are used, where obtainable, the quantity used, possible avenues for increasing use or application, and the chemical and physical characteristics of the available ores. Only with those data at hand, is it possible to arrive at a convincing answer to the question whether the reserves of manganiferous iron ores are adequate to satisfy the annual demand of the presently known iron ores for the full life of the latter. That they should last is vital; and to ascertain whether they will last was the purpose of the present investigation, which marks the first attempt to study these Lake Superior reserves. The Lake Superior region possesses and supplies the full assortment of iron ores needed for the conversion of ore into pig iron and steel ingots and castings. These ores are named bessemer, low-phosphorus and high-phosphorus non-bessemer, manganiferous and siliceous; and to include the term aluminiferous would be in keeping with the most recent nomenclature adopted by some dealers. About 35 or 40 years ago, perhaps less, most of the Lake Superior ore which is being used today was the material then considered either useless or too poor for immediate use; perhaps it was considered no more than a future reserve. An examination of the analyses of ores and the guarantees in the sales of those older times convince one that the opinions of those days must have been governed by only small differences in analyses. Some grades of ores used today in substantial amounts were used most sparingly only one or two decades ago. The relative quantities of the different ores used are ever changing; and, bit by bit, the metallurgy and the opinions are ever changing and the prejudices against certain ores and practices decrease. This is unquestionably more pronounced for the manganiferous ores than for any other kind. If, when using the present data for manganiferous ores, we will only be content to make allowances for the same experiences other kinds of ores

Jan 1, 1927

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand It appears that. one&apos;s interest in, and satisfaction with, the discovery of an array of news experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one&apos;s expectation of what sort of new experimental discovery may lie around the corner Conversely, as a theoretical physicist one&apos;s satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows Of course, there have been long and stretches in the history of physics in which new data of unquestioned ultimate importance ham e piled up, without much inspiration or illumination in the way of understanding For 50 years spectroscopy had such an and history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the Same sort of situation as spectroscopy before the advent of Bohr A great many kids, of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By H. Rumfelt

The author demonstrates an approach for analyzing overcasting requirements for a stripping project. This approach to the problem employs indicated trends in the relationship of the weight of the machine (only electropowered draglines are considered) to its ability to do stripping work. Strip mining in the domestic coal industry is contributing a greater proportion of overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely). Accompanying these changes, there have been continuing studies searching for procedures to appraise deeper stripping problems. Although the only known practicable way to accurately evaluate a proposed stripping venture is to make studies (including cost estimates) step by step, it is nevertheless desirable to have a quick method for making preliminary evaluations of potential strip mining operations. A recently devised digital computer method of providing a preliminary simple overcasting analysis for a stripping prospect relates the indicated trends in the relationship of the weight of the machine to its ability to do stripping work. In addition, this approach employs situations where the geometry of each cut-and-spoil section is assumed to take certain defined relationships for varying overburden depths. Slopes are necessarily considered to be stable, which means such practical factors as the mechanics of soils are neglected for the sake of convenience. Definition of Terms: Photographs A and B show a shovel-type and a dragline-type of simple overcast operation, plus terms used to denote certain parts of a pit. Pits that follow a straight line when projected on a horizontal plane are referred to as straightaway. It has been assumed that all section drawings accompanying this article pertain to straightaway cuts which, in turn, means that areas can be compared by relative volume. The volume of overburden is measured in virgin cubic yards. Material displaced from its virgin state to a spoil area normally occupies a larger volume than when in situ; the difference is termed swell, and it is expressed as a percentage of the original volume. For example, if the original cut volume is denoted V cu yd, and the spoil volume is 1.2 V cu yd, the swell is a positive 20 pct. MAXIMUM USEFULNESS FACTOR (MUF) CONCEPT Men experienced in overburden removal give emphasis to the weight of the machine in relation to its value as an excavator. From the writer&apos;s understanding, value has been only loosely defined and discussed generally and vaguely. The concept is considered important, however, since it is based upon the observations of many men. It provides a clue for the approach taken to solve deep stripping problems. In the procedure described below, value has been arbitrarily established as the product of the nominal dipper size of the shovel (or dragline) times a functional dumping reach. MUFs—Shovel: A shovel&apos;s capability to handle thick overburden is usually limited by its ability to dispose of the spoil. Thus the dumping reach, as well as its dumping height, is significant. The angle of repose of spoil material must also be considered. Although such slope angles vary among different mines, jobs, and materials, a slope of 1.25 to 1, frequently found in both planning and practice, is used by this author in the illustration of this analytical method. The relationship of the shovel&apos;s geometry to a stripping operation is shown in Fig. 1. To gain maximum advantage in constructing spoil piles, the shovel is placed so that its tracks adjacent to the spoil are as close as possible to the rib of the coal deposit. A vertical plane passing through the line

Jan 1, 1961

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By Alfred Weiss

Daniel C. Jackling&apos;s innovative concept for handling low grade ores ushered in a new philosophy of open pit mining. As one of the greatest minemakers of all times he revolutionized major segments of the industry and helped strengthen US defense efforts during World Wars I and II by making possible the tremendous copper supplies from US mines. Many great mining men have since followed in his footsteps with their discoveries of new orebodies or development of new mines. Their brilliance in leadership can also be traced to the coupling of a new idea to the physical nature of the materials in the earth&apos;s crust or to the extractive stages of minerals recovery. The minerals industry is now in another era of change and must again devise techniques to meet the challenge. The task is not only to create new exploration techniques and develop new mining methods, but, I believe, to optimally apply new concepts and tools in daily decision-making.

Jan 11, 1978

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, &apos;750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

By L. W. Legerwood

During the past three decades, the oil industry has expended increasing eflorts seeking improved drilling tools or systems to reduce drilling costs. The total cost of these efforts is unknown, but it certainly amounts 10 tens of millions of dollars. Most of the "new" system that past and present investigators have sought to develop actually are old public information. In seeking to implement new-systern concepts, investigators have tested the following: impact at frequencies ranging from 6 to 300 cycles per second; electrical, mechanical and hydraulic meam of actuating percussors; bit rotary speeds up to 2,000 rpm; electric and hydraulic bottom-hole means of rotating bits; bottom-hole machines with power outputs up to 400 hp; shock waves; explosives; high-velocity pellets; flame; arc; grinding wheels; abrasive jets; erosion by high-velocity gases; chemical attack; electric current; magnetic waves; retractable rock bits; reelable drill pipe; continuous coring with reverse circulation; and automation of drilling rigs. Table I shows how these investigations are grouped for discussion purposes in this paper. In spite of these efforts to discover new and improved systems, rotary drilling main;aim its economic leadership. Undoubtedly, rotary drilling costs will continue to be reduced by rigid application of the best available technology and by development of new rotary technology. In view of the extensive past development programs, however, significant long-range improvement appears to be a research, not a development problem. Research must postulate and prove theories and principles governing variour subsurface rock-failure processes pertinent to both rotary and new systems. Ah, research must produce physical and engineering data relative to these processes. When such information is available, earth boring will graduate from an art to a science. Major improvements in rotary drilling can then be expected, and the systematic evolution of an improved drilling method can be initiated—with a strong probability for success. Development of drilling methods other than rotary drilling has been one approach investigated by the industry as a means for reducing drilling costs. Major cost-reduction efforts, however, have been centered on engineering development work aimed at incremental improvements in rotary drilling. A relatively minor effort has been expended to establish basic physical principles and engineering data pertaining to the earth-boring process which can serve as a foundation for the development of cost-cutting drilling hardware. Current oil-industry economic trends have added impetus to the need for effective programs to reduce drilling costs. However, areas for expanded future efforts should be selected only after careful study of past investigations. It is the purpose of this paper to review past and Dresent industry efforts to develop new drilling tools or systems and to suggest areas where additional science is needed. Past reviews of drilling methods have been limited to a few processes prominent at the time the reviews were made. This paper seeks to present a concise, well organized review of all methods that have received actual development or test work. The preparation of a paper seeking to review all past developments is fraught with many difficulties, not the least of which are errors in or obsolesence of printed matter used as source material and the lack of data on industry developments which have not been published. Since de-

By E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940.They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Hey1 and Patterson oscillating table, 1927. 4. "Stump Air-Flow," pulsating air jig, 1932. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAX TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corporation, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943