Search Documents

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By W. C. Maurer

A drilling-rate formula for roller-cone bits is derived from rock crater-ing mechanisms. This formula holds for "perfect cleaning", which is defined as the condition where all of the rock debris is removed between tooth impacts. Under these conditions, the drilling rate is directly proportional to the rotary speed and to the bit weight squared, and inversely proportional to the bit diameter squared and to the rock strength squared. Under imperfect cleaning conditions, such m those usually present in field drilling, re-grinding of the cuttings occurs under the bit, and the drilling rates fall below those for perfect cleaning. INTRODUCTION Drilling with a roller-cone bit consists of two fundamental operations: the formation of craters under the bit teeth, and the removal of the broken rock from the craters. To delineate the mechanisms of drilling, it is first necessary to understand the mechanisms involved in the formation of individual craters and then to relate these mechanisms to the over-all drilling operation. CRATER FORMATION When a bit tooth impacts a rock, the rock is elastically deformed until the crushing strength of the rock is exceeded, at which time a wedge of crushed rock is formed below the tooth1, 2 as shown in Fig. 1. As additional force is applied to the tooth, the crushed material is compressed and exerts high lateral forces on the solid material surrounding the crushed wedge.- en these forces become sufficiently high, fractures are initiated below the tooth and propagate to the free surface of the rock. The trajectories of these fractures intersect the principal stresses at a constant angle,'s4, as predicted by both Mohr's and Griffith's theories of failure. It has been experimentally 3,1 .6 that the volume of an impact crater, V,, varies as where Ec is the total energy imparted to the rock during the formation of the crater, and E is the threshold energy required before cratering is initiated (Fig. 2). Indexing experiments' have shown that, when there is a second free face to which the crater can fracture, a larger volume of material is removed and that above a transition zone there is a linear relationship between V, and Eo., which has a slope equal to the relationship for the single crater. The beneficial effect of indexing tends to offset the threshold energy requirement to a large extent, as shown in Fig. 2, and the relationship is closely represented by Rate-of-loading effects have been used to explain the nonproportional relationships usually obtained between drilling rate and rotary speed. The data4, in Fig. 3 show that the Ec/Vc parameter remained constant for craters produced with impact velocities ranging from 10 to 8,000 ft/sec. Since no rate-of-loading effects were detected over this wide range of loading rates, it seems improbable that there would be detectable rate-of-loading effects present in the small changes in impact velocities produced by varying the rotary speed. The writer has shown (Fig. 4) that, for craters produced in rock by impacting spheres, where X is the depth of penetration. Simon2 has shown that this relationship also holds for craters produced in rock by penetrating wedge-shaped chisels. The energy used in crater formation is

By H. J. Struth

In these trying times of proration and low oil prices, it is decidedly necessary for all branches of the petroleum industry to accord full recognition to the economic phenomena that contribute to its varying state of welfare. Perhaps no other single factor has a more important bearing upon the general oil situation than the supply and demand of gasoline. Year after year, the records have shown that the degree of prosperity or depression accompanying the industry's developments has been to a large extent influenced by the degree of balance maintamed between the supply and demand of gasoline. More and more it is being realized within the industry that equilibrium between the supply and demand of gasoline forms the basic structure of crude and product market values and, consequently, the deciding factor in the financial results of the industry as a whole. The influence of the gasoline situation upon the market and financial structure of the petroleum industry was effectively demonstrated during 1930, when excess accumulation of gasoline undermined not only the refined oil market but the crude market as well. In fact, it was a top-heavy gasoline situation that defeated the realization of benefits that might have accrued from an otherwise favorable statistical position in the producing branch of the industry. Indicative of this is the fact that crude oil production was curtailed to the extent of 98,323,000 bbl. last year, while refinery runs to stills were maintained at an excessive rate until late in the year, creating an excess gasoline production of 6,663,000 bbl. above actual requirements. Nevertheless, the movement to curtail refinery operations during the closing months of the year prevented a far worse situation, although it came too late to turn the ebbing momentum of the general oil market. Despite the severe depression of the market values that accompanied 1930 developments, it can be said that the results attained during the closing months of the year, in the direction of production control, marked a decisive turn in the industry's economic affairs. In fact, a review of the oil situation from every angle points definitely to a better general understanding and recognition of the workings of the economic law of supply and demand. As a result, the year closed with crude production in

Jan 1, 1931

Horace F. Lunt, York, Montana* :—Two years ago I visited the region described by Mr. Jennings and assisted in the examination of a somewhat similar group of deposits in the White Mesa sandstone on the Navajo Indian Reservation, 125 miles north of Flagstaff and 50 miles east of the Kaibab plateau. There, the Triassic red sandstone is less than 200 ft. thick, and is overlain by a stratum from 200 to 250 ft. thick of white sandstone, which gives the name of " White Mesa" to that locality. The white sandstone shows all phases of crossbedding in great complexity, and evidently marks a period of oscillation and subsidence of the water, or an elevation of the land, at the close of a geological epoch. The prevailing color is white or gray, but occasionally it is red. In structure, it is composed of well-worn grains of quartzsand, from which most of the cementing material has been leached out, leaving it soft and friable. Possibly the cement was ferruginous, as is indicated by occasional traces of red color. The copper-deposits consist of a replacement of the cement of one particular cross-bedded stratum of the sandstone by chrysocolla, having also at times various quantities of tenorite in grains or masses. Some specimens of the ore contain as much as 32 per cent. of copper. Generally the copper-deposits are a few hundred cubic feet in size, and no strict line of demarcation is shown between them and the surrounding sandstone, the bluish-green color of the chrysocolla gradually fading into the white of the sandstone. The ore is apparently associated with small vertical crevices or fissures. Some of the deposits show a distinct vein-structure, while others do not. The origin of the ore is not very clear. Undoubtedly the solutions, coursing through the crevices noted above, played a prominent part in its deposition, as possibly

Jan 1, 1904

By L. S. Darken, H. A. Wriedt

THE constitution diagram of the iron-copper system derived by Daniloff' exhibits, at the iron-rich end, phase fields similar to those of the iron-carbon diagram. At 1484° 1094°, and 850°C there are, respectively, a 6-y-L peritectic, a y-E-Lperitectic, and a a-y-E eutectoid. The phase designated E is copper-rich, containing 4 pct Fe or less according to the temperature. The composition of copper-saturated ferrite (a-solid solution) has been determined previously only twice as a function of temperature. By electrical conductivity measurements, Buchholtz and Köster2 found 3.4 pct Cu in ferrite at a eutectoid temperature of 810°C. They represented the composition of saturated ferrite by the equation, log (%Cu) = 4.32-4125 (1/T) Gregg and Daniloff3 reported that Köster later modified his opinion, raising the indicated eutectoid temperature to 833 °C and the copper content of eutectoid ferrite to 3.7 pct. The literature contains several indications4-7 that the work of Köster and his co-workers is not reliable. Norton,8 using an X-ray method, found that 1.4 pct Cu dissolved in ferrite at the approximate eutectoid temperature of 850°C and that the solubility decreased to about 0.3 pct at 700°C. Below 700°C his experimental data show almost no change in solubility. These findings, although inconsistent with the work of Ruer and Goerens4 and of Smith and Palmer,7 have been used generally since their publication. In investigations involving the observation of arrests in temperature during continuous heating or cooling the precise location of the eutectoid temperature has been obscured by a large hysteresis. The more reliable work 579 where the results are not effected by this hysteresis indicates a eutectoid temperature between 840° and 850°C. The foregoing discrepancies, along with a few observations in this Laboratory relating to the precipitation of copper from ferrite, prompted us to rein-vestigate the lower temperature portion of the Fe-Cu system. In this investigation the solubility of copper in ferrite was obtained by the chemical analysis of high-purity iron equilibrated with copper-silver alloys. This method eliminated the necessity for retaining by a quench the physical state of the specimen existing at the equilibration temperature. EXPERIMENTAL The reaction of the iron with the copper alloy was

Jan 1, 1961

By R. P. McLaughlin

In most branches of the mining industry it is a well-recognized fact that care must be taken to protect the mineral deposit from undue physical injury. It is comparatively easy to grasp this idea when the mineral is a solid and the lives of workmen depend directly upon the care with which it is removed from its natural position, but when the product is a liquid drawn up from pools several thousand feet beneath the surface of the ground through openings only a few inches in diameter, it requires some imagination to picture underground conditions and the changes which must often occur. The development of the petroleum deposits of California has been attended by numerous accidents, the results of which are readily noticed at the top of the wells and in the profit and loss accounts of the operators. Determination of the cause of these accidents has been the subject of considerable study, which naturally has fallen upon men familiar with technical methods. The greatest damage to the oil deposits of California has resulted from water finding its way into the oil-bearing sands, and it is the purpose of this paper to set forth briefly this phase of the oil industry. Much of the material here presented has previously appeared in publications issued by the California State Mining Bureau, which, under the direction of State Mineralogist Fletcher McN. Hamilton, has investigated the subject and taken steps toward improvement of conditions. The writer, having been in charge of this branch of the Bureau work, has gained considerable knowledge of existing conditions. Generally speaking, the oil-bearing formations of California are soft, unconsolidated sand beds, separated by clay strata, which are also soft. Some of the sand beds carry water instead of oil. All of the beds are more or less separated, probably being of lenticular shape. Very few of the beds in the oil fields lie flat or undisturbed over any great area. Folding and tilting are common, and faulting also occurs in some of the fields. The accumulation of oil is not confined to any single structural feature, such as the anticline, but occurs in many other structural features. Water-bearing strata occur in practically every oil field in the State. Complete data are not at hand for a comparison of the damage

Jan 1, 1916

By H. M. Howe

THIS paper presents an experimental verification of some of the predictions made by one of us' concerning 'the influence of certain conditions of casting upon the size and position of the pipe', and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following A. That the pipe is shortened and the segregate raised 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last freezing-part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis ; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jul 1, 1907

By Henry G. Granger

DURING upwards of three thonsand miles of canoc-travel in South America, including several mishaps, the writer has unfortunately lost his book of notes taken during the year 1894 in Dutch Guyana, or Surinam. But a year spent in a foreign country, visiting its principal mining properties, is necessarily productive of indelible memories and impressions, and some of these may be of interest to the Institute. The Guyanas include British, or Demerara, Dutch, or Surinam, French, or Cayenne, and the Disputed Territory, or that portion of Brazil on the northeast coast of South America. After passing the picturesque mountainous coasts of Colombia and Venezuela, one reaches a low, flat mud-bank which extends far out into the sea, so that from the steamer, over a couple of leagues of turbid, shallow water, one call just see the dismal outline of the pestilential "bush" that fronts the Caribbean sea, clear around to the mouth of the Amazon. Here, iii the order mentioned above, are the Guyanas. So much has been said about this out-of-the-way section during the late excitement over the Venezuela boundary question, that the historical part of the subject may be advantageously condensed. Gold-mining in the Guyanas is altogether placer-mining, and is of the same general nature throughout; hence by describing the methods in use in Surinam and the results there achieved, ail idea will be given of the work throughout the field. The product of this section is about three to four millions of dollars annually, mostly from Demerara, not because of superior richness of its placers, but as a result of its very much larger population, which exceeds twice the aggregate census returns of both Surinam and Cayenne. Mining ill all this section is of comparatively recent date, and is indirectly due to the decline of the sugar-industry. After the introduction of beet-sugar scores

Jan 1, 1897

By C. F. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by some typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects. [ ] In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

Jan 1, 1928

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By C. M. Weld

In the course of my professional work in China during the fall of 1907, I had an opportunity to visit the iron-ore mines at Ta-yeh in Hu-pei province (long. 114O 50t E., lat. 30' 20t N.). It occurs to me that a rescript and discussion of my notes taken at that time should be of interest, particularly as supplementing the exceedingly interesting recent paper of Thomas T. Read on The Mineral Production and Resources of China.' Ta-yeh is situated near the right bank of the Yangtze river. The mines are at an average distance of about 16 miles from the river-port Shi-hui-yao, which in turn is some 70 miles SE. of Hankom. The ores are shipped to the works of the Han-Yeh-P'ing Iron & Coal Co. at Hanyang, as also very largely to the Japanese government iron- and steel-works at Wakamatsu, Japan. Smaller qnantities have been exported to the Pacific coast of the United States. These ore-deposits have been briefly noticed in a number of publications, but, so far as I know, Mr. Read's description, in his chapter or1 the iron-ores of the Chinese Empire,2 contains the first attempt to define their geological character. In his more recent paper Mr. Read follows very closely the text of his earlier description. To quote briefly from the recent paper, he says : " The iron-ores at Ta-yeh .... lie along the contact between a marble and an intrusive body of a dark-gray syenitic rock." He refers to a figure which exhibits in plan, but not in section, the relative positions of the syenite, ore-bodies, and limestone. The contact is seen to trend approximately E-W., with the syenite on the north and the limestone on the south. " The syenite lies to the north of the marble, and a few miles farther north the marble again appears, iron-ore again being present along the contact." No litho-

Jan 1, 1913

By Walter Nummela

INTRODUCTION By the end of 1979 pellet productive capacity from the processing of low grade iron ores in the Lake Superior-District will total 86 million tons per year. Of that tonnage, 72 million result from the processing of magnetic ores such as taconite, about 6 million tons from the flotation processing of relatively coarse grained specular hematite, and 8 million tons from the processing of fine grained non- magnetic ores at Tilden. The Tilden flowsheet represents a break- through in the processing of this type of crude ore and hence is unique in the Lake Superior District (1). Operations at Tilden started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleve- land-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling- Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Other companies have conducted extensive pilot plant tests or are in commercial production in the processing of fine grained non-magnetic ore materials (2). Flowsheets and reagent schedules may be different for each particular application, but some of the problem areas in the processing of Tilden ores have also been experienced at operations such as the IOC Plant at Sept-Isles, at Lamco and at Bong in Liberia, and in pilot testing of Fabrica ores of Ferteco Mineracao in Brazil. With a grind of about 80-85% -500 mesh resulting in 50% of the particles in the concentrate being less than 15 microns, a discussion of the pro- cessing of Tilden type ores fits the topic of this workshop. There are very large tonnages of fine grained non-magnetic crude ores which exist throughout the Lake Superior District and other iron ore producing regions. These fine grained non-magnetic materials constitute an important source of iron minerals. Before going into specifics of the flowsheet, it is important to

Jan 1, 1979

By Arnold Hague

In the short time allotted to me* I can only hope to present to you a brief sketch of the main geological features of the country which you are about to visit. My remarks must, of necessity, be more or less incomplete, as my desire is not so much to elucidate any special problem connected with the many interesting geological questions to be found here, as rather to offer such a general view of the region as will enable you, during your five days' trip through the Park, to understand clearly something of its physical geography and geology. The Yellowstone Park is situated in the extreme northwestern portion of the Territory of Wyoming. Its boundaries, as determined by the original Act of Congress setting apart the Park, are very ill-defined. At the time of the enactment of the law establishing this national reservation, the region had been but little explored, and its relation to the physical features of the adjacent country was but little understood. Since that time, surveys have shown that only a narrow strip, about two miles in width, was situated in the Territory of Montana, but it was also found that a still narrower strip extended westward into the Territory of Idaho. The question of properly establishing the boundaries, -based upon our present knowledge of the country, is now before Congress, and an Act has already passed the Senate, proposing to make the northern boundary coincide with the boundary between Wyoming and Montana, and the western boundary coincide with the Wyoming and Idaho line. The Act under consideration extends the southern boundary of the Park to the 44th parallel of latitude, carrying the area of the reservation southward nine and one-half miles. The eastern boundary is made to coincide with the meridian of 109' 30') adding a strip of country about twenty-four and one-half miles in width along the entire eastern side of the Park.

Jan 1, 1888

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By S. L. Hoyt

ABOUT three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. ? This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some com-ments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1.

Jan 1, 1937

By George S. Rice

Instantaneous outbursts of gas in underground workings are similar in effect to great blasts of explosives, but without heat effects. Fortunately they occur only in a few localities in exceptional coal fields of the world and under exceptional geologic conditions. Such violent outbursts should not be compared with the ordinary outflows of gas into coal mines or with explosions of gas and dust. The phenomenon is essentially one of gas held in circumscribed areas under very high pressure and as a mining face or heading approaches such a place and the mining excavation sufficiently weakens the natural surrounding dam or shell, this is burst by the pressure just as by the discharge of a mass of explosives. The outbursts, so far as known to the writer, have been confined to coal beds and have not occurred in other mineral deposits. Hence, as discussed later, he believes that it is the relation of the gases to the coal material that is a factor in conjunction with others in producing conditions which permit the phenomena to occur when mining is done. The gases in most instantaneous outbursts have been hydrocarbon gases but in two coal fields they have been definitely found to be chiefly or wholly carbon dioxide. One of these localities in which CO2 outbursts have been frequent and have caused loss of life is in the southern part of the Gard basin, near Alais, in southern France. In 1919, the writer visited the Fontaine mine in this field the day following the occurrence of an outburst by which two men were smothered by carbon dioxide and fine dust. After 24 hr. the CO2 had not been entirely removed by the ventilating current. Occasional outbursts of CO2 have also occurred in other small basins in France, causing accidents, as in Puy-de-Dome. However, mines in the Gard basin, north of those in which CO2 outbursts have occurred, have experienced hydrocarbon gas outbursts. In the Lower Silesian coal field, Germany, there is a group of mines which have been subject to many instantaneous CO2 outbursts, some causing serious accidents, but the greatest disaster occurred recently

Jan 1, 1931

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By George Rice

INSTANTANEOUS outbursts of gas in underground workings are similar in effect to great blasts of explosives, but without heat effects. Fortunately they occur only in a few localities in exceptional coal fields of the world and under exceptional geologic conditions. Such violent outbursts should not be compared with the ordinary outflows of gas into coal mines or with explosions of gas and dust. The phenomenon is essentially one of gas held in circumscribed areas under very high pressure and as a mining face or heading approaches such a place and the mining excavation sufficiently weakens the natural surrounding dam or shell, this is burst by the pressure just as by the discharge of a mass of explosives. The outbursts, so far as known to the writer, have been confined to coal beds and have not occurred in other mineral deposits. Hence, as discussed later, he believes that it is the relation of the gases to the coal material that is a factor in conjunction with others in producing conditions which permit the phenomena to occur when mining is done. The gases in most instantaneous outbursts have been hydrocarbon gases but in two coal fields they have been definitely found to be chiefly or wholly carbon dioxide. One of these localities in which CO2 outbursts have been frequent and have caused loss of life is in the southern part of the Gard basin, near Alais, in southern France. In 1919, the writer visited the Fontaine mine in this field the day following the occurrence of an outburst by which two men were smothered by carbon dioxide and fine dust. After 24 hr. the CO2 had not been entirely removed by the ventilating current. Occasional outbursts of CO2 have also occurred in other small basins in France, causing accidents, as in Puy-de-Dome. However, mines in the Gard basin, north of those in which CO2 outbursts have occurred, have experienced hydrocarbon gas outbursts.

Jan 1, 1931

By Paul Cook

THE ore deposit of the Buckhorn Mines Co., Buckhorn, Nev., is peculiar in being a shallow kaolinized mass of material with basalt walls, and having apparently no direct connection with any of the usual gold-bearing rocks. The average ore contains 16 per cent. waiter of hydration, and the cyaniding of this hydrous clayey material offered unusual difficulties as compared with the typical gold quartz ores of Nevada. The orebody was thoroughly developed; then the mill was built according to the latest cyanide .practice, with such changes as were thought to be demanded by the peculiar nature of this ore. Upon starting the mill, the ore proved more difficult to handle than had been anticipated. It is hoped that an account of how these difficulties were met may prove of interest to anyone having a clayey ore to handle and to the profession in general.

Jan 9, 1916

By V. G. Cawagdan, E. M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond (Bond and Maxson, 1943) grindability data and the operating work index is presented. The objective was to produce a sand cyclone overflow containing not more than 6% 210 µm (+ 65 mesh). This has never been attained, even at low milling rates. Significant improvements in throughput were achieved by instituting equipment changes and process modifications within the grinding circuit. Grind improvements were achieved with enlargement of cyclone spigots, grinding at reduced densities, and decreasing the opening of the ball mill discharge. Additional grinding capacity was realized by converting the concentrate regrinding mill into a secondary ball mill. The previous 20% 210 µm (+ 65 mesh) grind improved to under 15% 210 µm (+ 65 mesh). The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1985