Search Documents

By Helmer Hedstrom

GRAVITY surveying with the torsion balance or the pendulum for ore prospecting purposes has generally not been considered practical or even possible. It is the intention of this paper to show that a fast and sensi-tive gravimeter can be very useful in ore prospecting, as an auxiliary to the electrical and magnetic instruments. A number of gravimeters have been constructed and put in practical use in the last seven or eight years; for instance, by Ising, Lejay-Holweck, Haalck, Hartley, Thyssen, Noergaard, the Humble Oil and Refining Co. and the Gulf Production Co. Their main application, apart from their use for geodetic surveys, has been for structure mapping in oil prospecting. There is no record that any of them have been used for ore prospecting. About the middle of 1934 the Boliden Mining Co., in Sweden, began experiments in constructing a static gravity meter sensitive enough for ore prospecting. Calculations and considerations that will be discussed later in this paper showed that this would necessitate an accuracy in the measurements of 0.1 milligal-roughly, one ten-millionth part of the total force of gravity. The first successful practical field tests of the instrument were made in January 1936. About the middle of 1937 the Boliden gravimeter was perfected. Ore prospecting with this instru-ment is now regular practice in Sweden, especially for the testing of indications given by geoelectric and magnetic methods.

Jan 1, 1938

By R. Sprycha, J. Szczypa, W. Janusz, J. Neczaj-Hruzewicz

INTRODUCTION Because large aqueous suspensions of various fine solids originate during the beneficiation of ores, the Mining Industry constantly requires efficient and feasible dewatering methods. Among the techniques currently in use (1,2), filtration (vacuum, press) and centrifugation are fairly expensive and thus are limited to use with more valuable materials. Furthermore, installations of reasonable size produce only moderate outputs. Therefore, tailings from ore dressing plants are usually treated by sedimentation or settling techniques with a tailings dam as the ultimate sedimentation basin (3). Apart from growing environmental and economic questions, the solid product obtained from the tailings dam basin has in most cases, a rather high moisture content and a persistent semi-fluid consistency. Thus, it is difficult to transport and use further. On the other hand, the solids may be utilized as a filling material, fertilizer, etc. providing they are dry enough and properly granulated. Demands for an improved technique are met to a great extent, by the technique presented in this paper. AGGLOMERATION OF FLOCCIJLATED SLIMES Origin and Qualitative Description of the Process Phenomena of consolidation and pellet formation in flocculated fines were first observed by Yusa and Gaudin (4) while studying rheological properties of flocculated kaolinite. On this basis, methods of separating liquid from solids have been worked out (5-7) and many possibilities for application have been suggested (5,6). Yusa termed the technique "wet pelletization''.

Jan 1, 1980

By Culver, Richard S.

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result.

Jan 1, 1968

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By J. Grosso, D. J. Nagel

In many metallurgical studies, it is necessary to reveal the composition and structural properties of materials. Usually this is done by etching, but some substances do not etch well or easily. Anodizing is known to provide an alternate treatment in many cases. In general, this technique is simple, often more sensitive to composition differences than etching, has excellent resolution, and provides variable contrast in those elements and alloys which anodize. Here we report the use of anodizing in diffusion studies in the TiCb system. Fig. 1 shows a cross section of the diffusion zone in a TiCb couple. The anodizing has clearly revealed both composition and crystallographic features. The maximum bulk penetration of the titanium into the columbium is marked by a sharp line because of the steep concentration gradient. The titanium grain size and orientation differences are also evident. Variation in the grain size reflects the gradually decreasing columbium concentration.

Jan 1, 1967

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.'" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By E. A. Anderson, M. L. Fuller

The copper-zinc phase equilibrium diagram has been the subject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100' to 400' C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the composition at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical conductivity and microscopical methods mere used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-composition relationship. The microscopical method distinguishes, by direct inspection, between the homogeneous solid solution alloys and those having a secondary constituent in addition to the solid solution phase, and thus indicates from the examination of a series of alloys the solid solubility limit.

Jan 1, 1934

By Walter P. Jenney

An investigation, conducted by the author, was begun in September, 1889, by the United States Geological Survey, having for its object the study of the questions bearing upon the occurrence and manner of formation of the deposits of lead- and zinc-ores in Missouri and the adjoining States. The field-work was completed in December, 1891. During the first season the State Geological Survey of Missouri furnished an assistant, and in other ways co-operated in the research within the boundaries of that State. In order that the ore-deposits of the southwest might be compared with those of other sections of the Mississippi valley, an examination was made of the lead- and zinc-mining area of Wisconsin-Iowa, and of the argentiferous lead-mines of the region extending westward from Hot Springs, Arkansas, to Indian Territory. In the discussion of the general geology, and in comparisons between the ore-deposits of the Mississippi valley and those of the Rocky Mountains, the writer has drawn largely from his personal experience, having been engaged for many years in professional work as a geologist and mining engineer in that region. The Director of the U. S. Geological Survey and the Scate Geologist of Missouri have kindly consented to the publication of the present paper. While giving the more important economic results, an endeavor has been made to set forth the unity of plan which appears in the formation of the deposits of lead and zinc of the Mississippi basin, and to show their relation to the argentiferous ores of the Rocky Mountains—that the ores of gold, silver, and mercury, and also of copper, antimony, zinc, and lead, have a universal common origin, irrespective of the geological formations in which they occur.

Jan 1, 1894

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By E. V. Crane

A tremendous volume of the metal rolled annually into sheets strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features In common with rolling and wire-drawing methods. Combinations of stresses are diffcrent, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group. Shearing Operations The shearing group of operations, including blanking, piercing, trimming, shaving, slitting, shearing, notching, parting and numerous variations and combinations of these enters once or more into the production schedule of practically every stamped or forged article. The transverse stress, set up in shearing, as shown in Fig. 1A, is a combination of an angular compressive thrust and a tensile stress which is also at an

Jan 1, 1931

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

THE Joint Committee appointed to consider a Code of Ethics for Engineers recommends, after delib-erate consideration, that each participating Insti-tute or Society adopt the short simple Code of Ethics following this report. The Committee further recommends that the following method of interpreting and administering the Code be adopted by each participating Institute or Society after any necessary provisions have been, made in the Constitution and By-laws of the Organization. The President of each Society or Institute shall appoint a Standing Committee on Professional. Conduct, to administer the Code of Ethics. The duties of such a Committee shall be to interpret the Code and to render opinions on any cases of ques-tionable conduct on the part of members that may be submitted to the Committee. These interpretations shall be reported to the Executive Board of the Institute or Society who may approve these interpretations, or take such other action as may seem just and necessary. The reports of the Committee on Professional Conduct, when approved by the Executive Board, shall be printed in abstract and in anonymous form in the Institute's or Society's monthly journal for the instruction and guidance of fellow members. This Committee on Professional Conduct shall be appointed in each Institute or Society by the President holding office at the time of the adoption of this Code and shall consist of five member one appointed for five years, one for four years, a third for three years, a fourth for two years and a fifth member for one year only. Thereafter, the President then holding office shall appoint one member annually to serve for five years, and shall also fill any vacancies that may occur for the unexpired term of the member who has withdrawn. These appointments shall he made from among the older members of the Institute or. Society, so that advantage may be taken of their mature experi-ence and judgment. The Committee after appointment shall elect its own chairman and secretary. The Committee shall have power to secure evidence or other information in any particular case not only from the organization's own members, but if it should seem desirable, from men in other professions. The Committee may also appoint sub-committees to consider certain cases when deemed necessary.

Jan 3, 1922

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By D. W. Fuerstenau

The United States is rapidly approaching an acute shortage of minerals. According to some observers, this situation may even be more severe than the energy crisis because the US consumes nearly 30% of the world's mineral production. With the mounting competition for world mineral supplies, we can no longer take for granted that foreign mineral products will be available to the US as abundantly as in the past. In 1973, US consumption of mineral raw materials was $35 billion. Of this, $7 billion consisted of imports. Without a drastic reorientation towards the mining of domestic mineral resources, the 1973 $7 billion deficit might mushroom to $100 billion by the year 2000. Thus, a return to domestic sources of raw materials will become absolutely necessary-and will be bucking the trend of the past 25 years, characterized by capital investment for growth in multinational overseas mining operations.

Jan 11, 1975

By Helen L. Cannon

BOTANICAL methods of prospecting for metalliferous ores are based on the premise that deposits at depth may be reflected chemically in surface vegetation. For the past several years, on behalf of the Atomic Energy Commission, the U. S. Geological Survey has investigated on the Colorado Plateau the application of botanical methods to uranium prospecting. Results suggest that orebodies may be found under a considerable cover of barren sandstone through the absorption of uranium and associated trace elements by plants growing at the ground surface. Plant physiologists have demonstrated that uranium is a necessary nutrient for plant growth and therefore is present in all plants.' The amount present is small but measurable. The absorption of uranium by plants growing over ore deposits forms the basis, therefore, for a method of prospecting by plant analysis.

Jan 2, 1954

By G. J. Benard

In the 1970’s, several plants have been built and others are in the design stage which use solvent extraction for recovery of copper from acid leach solutions. Other plants are presently being built for the recovery of nickel and cobalt from laterite ores by prereduction and ammonia leaching. A review will be given on the materials of construction for these leaching and solvent extraction processes. Many plants have factors in common which permit selection with a greater degree of accuracy. Based on pilot plant corrosion data, effective use of materials of construction includes proper selection of materials, substitution of lower cost plastics for alloys, and selection of materials resistant against chloride stress corrosion cracking.

Jan 1, 1974

The Secretary of the Treasury, in a recent ruling, allows 18 months from date of discharge within which former service men may reinstate their Government insurance policies lapsed f or non-payment of premiums. The point just now confronting the Bureau of War Risk Insurance and all those who are interested in the immediate and the future welfare of the young men who offered their lives for the flag and the country is that they be kept mindful that the provisions of the War Risk Act were not solely war measures, but that the framers of the Act provided insurance protection for all time to come for the boys in uniform and all dear to them. Under this ruling those making application for reinstatement will be required to pay only the premium on the amount of insurance to be reinstated for the month of grace during which they were protected, and for the current month. When the men are mustered out of the service, the insurance continues in force for one month and they are fully protected during that period even if their premium has remained unpaid. In reinstating, that month's premium will be required as well as the premium for the month in which reinstatement is effected. The ruling also stipulates that when applying for reinstatement the man must be in as good health as at the date of discharge, and so state in his application. After complying with these simple requirements, a Government insurance policy may be made as sound as on the day it was written. The Bureau of War Risk Insurance is now searching out its delinquent policy holders and offering them this renewal of Government protection. It needs the assistance of public spirited, patriotic, business and professional men everywhere, for the sake of our former service men, who must be given the information about its privileges to which they are entitled.

Jan 9, 1919

By Duane N. Goens, Clifford R. Porter

A 91 kg/h (200 lb per hr) pilot plant was constructed according to "Magnex" design. A non-compliance eastern coal which would generate more than 0.85 kg of SO2 per GJ (2.0 lb of SO2 per million Btu) upon burning was brought into compliance less than 0.52 kg of SO2 per GJ (1.2 lb SO2 per million Btu) during continuous operation of the pilot plant. Approximately 85% of the pyritic sulfur was removed while recovering 90% of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex design program is reviewed.

Jan 1, 1980

By Nick Barton

Simple methods for estimating the shear strength of rock joints and waste rock are reviewed. For the case of rock joints, the methods are based on a quantitative characterization of the joint roughness and the joint wall strength. Size-effects are found to reduce the peak strength of large joint samples to values below the ultimate or so-called "residual" values measured in the laboratory. Tilt tests and surface profiling on natural size blocks within the jointed rock mass are recommended for obtaining scale-free properties. The joint parameters obtained can be used to model complete strength-displacement-dilation behavior if this level of input is required. Large scale tilt tests can be performed with advantage on both rock joints and waste rock. The behavior of these two materials is surprisingly similar. Both are influenced by the size-effects on the compression strength of the rock, and both have similar log-linear relationships between effective normal stress and the peak drained friction angles. The resulting high values of friction near the toe or close to a slope face in either material can be misleading.

Jan 1, 1983