Search Documents

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passage- ways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground.

Jan 7, 1954

By AIME AIME

PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL MINNEAPOLIS, MINN. (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Nov 1, 1910

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent, of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART I.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent., of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results.

Jan 1, 1929

By Edward B. Durham

The refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying Illore than 200 parts of precious metals in 1,000, or, in mint parlance, over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum gronp that were in the bullion. This residue is relatively small, and is melted into bars and stored until suEcient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's osce, laboratory, and , re- spectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Jan 1, 1912

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.' After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927

By T. S. Jr. Sligh

OF all the qualities that are essential in a good cigar tobacco none is quite so important as the burn. This term is general and includes many points, the most important of which are evenness of burn, color of ash, firmness and coherence of ash, and fire-holding capacity. The fire-holding capacity refers to the length of time the leaf or cigar will continue to, glow after ignition. Chlorides tend to prevent complete combustion and products are formed thereby that are injurious to the flavor and aroma. On the other hand, the carbonates of the alkalies, particularly of potassium, aid the combustion and increase the fire-holding capacity. Barth1 thought that the harmful effect of the chlorides was due to their fusing and coating the tobacco, thereby preventing complete combustion. Schlosing,2 Nessler,3 and Garner,4 suggested widely different theories to account for the favorable action of potassium salts. In order to study carefully the action of the various salts upon the course of combustion of the cigar a knowledge of the temperature of the burning cigar is necessary. Lehmann5 who seems to be the only investigator who has made any attempt to determine the temperature of a burning cigar gives 480° C. as the maximum temperature which he recorded. It is evident, however, that his measurements were in error, probably on account of the method and apparatus used, since the lowest visible red corresponds to a temperature of about 575° C.

Jan 9, 1919

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated.

Jan 6, 1954

By Galen G. Waddell

Several years of rock-burst research conducted by the U.S. Bureau of Mines in cooperation with the mining companies of the Coeur d'Alene mining district, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem. A rock burst is the sudden, violent release of stored strain energy in rock by some mechanism of rock failure, generally accompanied by expulsion of rock with consequent damage to the mine. A burst may be audible for only a few hundred feet, or on the surface it may sound like a sonic boom miles away. A Dictionary of Mining, Mineral, and Related Terms, U.S. Bureau of Mines (USBM)* 1968yand defines a burst as Bureau "That phenomenon which occurs when a volume of rock is strained beyond the elastic limit and the accompanying failure is of such a nature that accumulated energy

Jan 1, 1971

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps : 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. .These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1964

By M. L. Samuels

DURING the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth-why and how it occurs-were treated in papers by Howe,1 Jeffries,2 Sauveur,3 Chappell,4 Beilby,5 Mathewson and Phillips,6 McAdam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,10 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size specified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filaments" wherein it is important to prevent "sagging" between consecutive turns of the helix." This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,13 in the hardening treatments of high-speed steels, 14.11 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is predominant no growth at all takes place. Under conditions in which

Jan 1, 1938

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920