Search Documents

W. P. PUTNAM,. Detroit, Mich.-There is one company that is heating these tubes in an upright position by passing electrical energy directly through the tube itself. The lower connection is attached to an indicator, which shows the point at which the steel passes through the critical range At that point the clamps are released and the tube is dropped into a well of oil. This method simplifies the heat treatment of tubes in long lengths. H. J. FRENCH.-I am not entirely familiar with. the method outlined, but it appears to have one serious disadvantage; that is, the length of tubing that is directly connected with the electrical contacts is wasted and must be cut off due to either heavy oxidation or burning. That is a serious difficulty, if true in all cases, and cannot be overcome, inas-much as it is very difficult to draw long tubes of thin wall. Having once obtained a lot of tubes, to cut, say 14 ft. in length, there is often little excess metal available to discard. Am I correct concerning the burning or heavy oxidation of the metal where it comes in contact with the tube.

Jan 12, 1919

The United States Employment Office of the Department of Labor, of which the division of engineering and education, under the direction of A. H. Krom, maintains an office at 29 La Salle Street, Chicago, Ill., is engaged in a classification of engineers in order to make their services more readily available in case of need. We have received a form used by this division, on which it requires only a very little time to indicate one's particular line of work, his experience and the salary that he desires. We have been asked to impress upon members of the Institute the distinct advantages that come through registration. Filling out the blank entitles an engineer to free employment service, provides him with direct contact with the Government, supplies him with information in regard to engineering affairs, and helps him to become successful in his profession. The Government wishes every technical man to register, so that it may know the strength and location of the engineering reserve. It is therefore the duty of every patriotic engineer, whether he needs a position or not, to register at once. Blanks can be obtained by addressing the office above noted.

Jan 10, 1918

By Waldemar Lindgren

THE important investigations of Dr. G. F. Becker at Steamboat Springs, Nev., in 1885, aided by the analytical work of W. H. Melville, established the fact that sulphides were being deposited at the surface by hot ascending waters.1 Steamboat Springs is situated near the eastern base of the escarpment of the Sierra Nevada, six miles distant from the Comstock lode. In a region of former volcanic activity, hot springs with a temperature of about 80° C. break forth through a fissure in granodiorite, and at the base of a basaltic bluff the waters have deposited a large amount of siliceous and calcareous sinter, some of which is colored red by antimony sulphide. The sinter from one of the springs was analyzed by Mr. Melville,2 and his results, re-calculated to grams per kilogram, showed [ ] The relative quantities of antimonious and arsenious sulphides are not given in the above analysis, but I believe that the former greatly predominated. The water of one of the springs was also analyzed by Melville and the re-calculation of this analysis to salts that were possibly present is given in Table I.

Jan 1, 1913

Bureau of Mineral and Topographic Survey, University of Kentucky, Lexington, Ky. Arthur C. McFarlan, State Geologist The Kentucky Geological Survey was abolished by a recent legislative act and the Bureau of Mineral and Topographic Survey at the University of Kentucky was created in its place Publications of the former Survey are distributed by the present Bureau Several series of papers and volumes have been issued but only those of Series 3, 4 and 6 are now to be had in whole or in part Of Series 4, (1912-18) only one group of papers is available Vol: 1, pt. 2, Miscellaneous papers on fire clays, limestones and coals of parts of the state (1913), $125. Of Series 3 (1904-1912), the following bulletins are pertinent and may be had. Bulletin 3, Coals, clays, etc., of Kentucky (1905), 50 cents, 14, Coals of the Pineville Gap region (1912), $1.25, 16, The Waverlain formation of east central Kentucky (1912), 50 cents, 17, Coals of the Tradewater region (1912), 50 cents, 18, Coals of Quicksand region (1912), 50 cents; 19, Geology and coals of the Central City, Madisonville, Calhoun, and Newberg Quadrangles (1912), 50 cents

Jan 1, 1933

By Arthur F. Taggart

The following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.' Screen apertures used are the average apertures of testing screeps of the meshes given. i . Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill, Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversise reground in pebble mill, see Card 113. Feed to mill through 2-in. mesh. Mesh Feed, Per Cent. Discharge, Per Cent.. + 1in. 5.50 ....... + 3/4. 28.00 + in. 30.00 ...... + 1/4in. 19.72 ....... + 10 10.87 2.10 + 20 2.42 8.00 -20 3.51 .....,. + 40 ....... 22.68 + 60 ...___ 10.50 4-80 ....... 11.80 + 100 ....... 3.90 -100 ....... 40.15

Jan 1, 1916

By Rush Sill

THE processes of superficial alteration depend on physical conditions, environment, geologic history and chemical and mineralogical composition. Superficial alteration is confined particularly to the zone of shallow circulation, as this is the zone of solution; its rocks are open and the circulation within it is compara-tively rapid. The enrichment of ore deposits in this zone, therefore, is of special interest. The depth of the vadose, or zone of shallow circula-tion, is variable, because its lower limit depends on the variable level of ground water. In moist, hilly countries its depth varies from a few feet to several hundred feet. In arid regions where the rainfall is low and evaporation great, this zone may extend to much greater depths. Permeability of the deposits . is essential to the downward migration of metals. In rocks, that have been fractured since the primary ore was deposited, there is generally more extensive and deeper enrichment than in ore deposits that have been but slightly fractured. A warm climate increases chemical action and abundant rain fall is favorable to enrichment. Low relief and slow erosion give long periods of weathering and thorough leaching.

Jan 9, 1922

Melbourne, capital of sedate Victoria, is oddly enough the home of a game known as "Australian Rules." Euphemistically described by devotees of the game as a cross between Rugby and Soccer, it appears to the novice to be more akin to organized mayhem. They don't even play it in some parts of Australia, but in Melbourne 60,000 to 80,000 whooping spectators throng the Cricket club of a Saturday afternoon to see a match. Actually, the game is fast and grueling but the victory laurels always go to the skillful team, the one that plays the ball rather than the man. Australians also play the ball in their ground rules affecting those interested in mineral exploration and mining. Prospecting Rights: Throughout the island continent, nearly all mineral rights are reserved to the Crown, administered by the individual states and, in the case of the territories by the Commonwealth government. The owner of the surface rights cannot sit on his minerals, and the term minerals even includes sand and gravel. Prospectors are protected by mining codes or ordinances of the various governments, which are quite similar from state to state.

Jan 10, 1964

By David Mitchell

THE production of fluorspar is one of the smaller nonmetallic indus-tries in the United, States with a capital investment-about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications: Consump- Specifications, Per Cent Use Form tion in 1936, Per Cent CaF2 SiO2 Fe2O3 Metallurgical Gravel 79 +85 -5 or lump Ceramic.. Ground 10 +95 -3 -0.1 Acid Ground 11 +98 -1 The concentration of the coarser sizes presents relatively little diffi-culty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

By Walter Morley

This paper is a record of the first of a series of tests on sulfide minerals to be made by the metallurgical department f the University of California. The purpose of the tests here recorded is to determine the action of standard oils, oil mixtures, and addition agents on the flotation of pyrites. The question of the commercial value of pyrite was not considered. Of the many factors affecting flotation, only two-the oil and the other agent used-were made variable. The flotation agents used are given in the accompanying table. PENSACOLA TAR AND TURPENTINE CO. (PENTARCO) NON-POL., SP. Dis. REF. PER No. KIND GR. POINTS INDEX ?VISC. CENT. 200 Refined wood creosote oil 0.965 105-275 1.5096 1.7 7-8 350 Crude pine wood oil 1.019 70-345 1.525 2.9 4 75 Crude wood turpentine 0.887 65-217 1.456 0.9 10-12 80 Crude pine oil 0.911 70-232 1.4894 1.1 8 750 Heavy pine tar oil 1.063 165-350 1.557 41.0 400 Wood creosote oil 1.025 190-360 1.4977 2.9

Jan 7, 1921

By David J. Dunn, Richard G. Martin

Of many physical parameters critical to design of grinding processes, impact of grinding media is among the most difficult to measure or predict. Yet impact of falling grinding balls, pebbles, or rods accomplishes the fine grinding essential to metallurgical recovery of most important minerals. Unfortunately, the same impacts that break ore fragments deform or crack grinding mill liners. A project was undertaken at Climax Molybdenum Company to measure impact forces in operating ball mills so that they might be used to calculate stresses in liner materials and be correlated with service performance of mill liner alloys. Towards that end, a method of measuring impact forces on ball mill liners using an instrumented grinding ball has been developed. Preliminary tests show that impact forces and contact stresses imposed on bare mill liners are quite high but are greatly reduced by cushioning when coarse ore particles are crushed between balls and liners. Compressive and shear stresses induced in liners not protected by coarse ore are so severe that deformation or minute subsurface cracking are inevitable in all but the small production grinding mills, regardless of mill liner alloy strength or hardness.

Jan 1, 1979

By David Mitchell

THE production of fluorspar is one of the smaller nonmetallic indus-tries in the United States with a capital investment-about $10,000,000. Shipments from United States mines' in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications: Consump- Specifications, Per Cent Use Form tion in 1936, Per Cent CaF2 SiO2 Fe2O3 Metallurgical Gravel 79 +85 -5 or lump Ceramic,. Ground 10 +95 -3 -0,1 Acid Ground 11 +98 -1 The concentration of the coarser sizes presents relatively little diffi-culty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

By Christopher Haycocks, Michael Karmis, David G. Lundy

Roof bolting is the most common means of support in under- ground coal mines. The main advantages of this support system are the relative ease of installation and the ability to provide a stable and unobstructed work area. Roof bolts can be broadly classified into two categories, mechanical and resin bolts. Currently, about 20% of all bolts used are the resin types, and trends show an increasing popularity of these kinds. Although the reinforcing effects of resin bolts have been well demonstrated, there is, nevertheless, a considerable lack of knowledge of their interaction with the surrounding strata. To study this interaction and to further investigate the mechanisms involved in resin bolting, an instrumentation system was designed and tested in a southwestern Virginia coal mine. The instrumentation system was composed of straingaged resin bolts, convergence and differential sag stations, and a borescope. Strain gages mounted on the bolt determined axial, bending, and shear strain at several levels along the axis of the bolt. The roof movement, as measured by the convergence and differential sag readings and as observed by the borescope, correlated well with the strains registered on the bolts.

Jan 1, 1983

By O. Lietard, J. Yvon, R. Mercier, J. F. Delon, J. M. Cases

INTRODUCTION Fineness is one of the main characteristics of powders and this parameter is the object of several definitions based on criteria connected with their uses as well as their determination methods. In trying to obtain the best reaction surface, fineness is characterized by the determination of the specific surface, but in other cases, particle size analysis is used. These two main methods are not, in fact, entirely independent and their complementary nature provides information concerning the morphology of the particles. In the case of a product formed by isodimensional spheres, the relationship between the specific surface and the diameter is well known: [S = 6 spd] where p is the specific weight of the material and d the diameter of the spheres. With no monodimensional spheres, but rather a granulometric distribution whose occurrences follow a mathematical law (1), the relationship is more complicated. The relationship between the specific surface measured by gas adsorption and the data of the particle size analysis is much more difficult to predict in the case of asymmetric porous particles, whose particle size distribution curves do not correspond to a known statistical law.

Jan 1, 1980

By Albert Roberts

Summary In response to a growing intolerance towards ground vibrations and noise as environmental pollutants the engineer must consider the effects of his operations as they are likely to be judged subjectively by the public at large. Much work has been done on the study of vibration damage to structures, but the damage criteria normally applied do not take into account any resonance effects, nor do they embody any subjective criterion. Mu1tiple criterion techniques of subjective appraisal have proven to be of value .in the assessment of environmental comfort in relation to ventilation, air conditioning, and lighting. One such scale, the Reiher-Meister Scale, has also been applied to ground vibrations and noise, and an attempt has been made to correlate this scale with objective criteria, using the parameters of frequency and displacement. This paper quotes examples and compares ground vibrations resulting from blasting, the operation of, vibrating and impact-hamner pi1e drivers, forge hammers, and railway and road traffic. The Reiher- Meister Scale was applied to a subjective-objective correlation in relation to vibrations from railway traffic and gave results which did not conflict with experience.

Jan 1, 1971

By Nicholas J. Grant, Noboru Komatsu

Electron-micrographic studies and hardness tests were made of an internally oxidized dispersion-strengthened Cu-12 vol pct SiO2 alloy follozuing longtime annealing at elevated temperatures. The rate of coarsening of SiO2 particles and the relationship between hardness and interpavticle spacing were Dispersion -strengthened alloys exhibit a remarkable stability of structure and properties at elevated temperatures compared with conventional alloys; nevertheless, when they are exposed to high measured. The rate of coarsening of SiO2 particles is controlled by the decomposition of SiO, rather than by the diffusion rates of silicon or oxygen through the copper matrix. The mechanism of coarsening was also studied by using a diffusion-couple technique. temperatures, weakening takes place as a result of coarsening of the dispersed phase. The theoretical treatment of the coarsening of dispersed phases has been treated by Greenwood,1 wagner,, and others3 by considering the interfacial energy of dispersions and the diffusion of solute atoms. Recently, experimental work on the coarsening of relatively insoluble, finely dispersed cobalt particles in copper was reported by Livingston,4 and on aluminum oxide in nickel by Dromsky, Lenel, and Ansell;5 according to these investigations, the rate

Jan 1, 1964

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending north-easterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 724 per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrothermal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons.

Jan 1, 1955

SINCE I have begun to tell you of the semiminerals that serve as colors, I wish to tell you of azure and green azure, so that you may know what they are. I tell you first that there are two kinds of azure, one called ultramarine blue by painters, and the other German blue. Ultra-

Jan 1, 1942

ASIDE-from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows: the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal.

Jan 1, 1928

By R. J. Lytle, E. F. Laine

The in situ high frequency electrical conductivity and permittivity of Colorado oil shale were recently measured. The measurements were made at 45 MHz (45 million cps) by transmitting from one borehole to two receiving boreholes, all boreholes in line. A differential measurement using the received signals was used to calculate the conductivity and permittivity.

Jan 1, 1983

By T. Chen

One of the limitations of the 3-dimensional Lerchs-Grossmann pit optimisation algorithm has been the difficulty in calculating an optimum pit with variable wall slopes. The difficulties have been related to establishing various wall slopes without changing the sizes of the blocks used in the normal computation, but still retaining an optimum solution.

Jan 1, 1977