Search Documents

By R. Maddin, C. H. Mathewson, W. R. Hibbard

According to conventional crystal mechanics, a face-centered cubic single crystal slips on the system {111} <110> which receives the highest shear stress in terms of the stated orientation of the stress axis of the crystal.l However, in brass, the slip process is never as simple as this conventional analysis indicates. There is always a second cooperating plane which contains the same slip direction as the primary plane.2&apos;3 There is still another cooperating slip system commonly called the conjugate system3 previously observed to function with considerable lag only after the rotation due to the action of the first plane had produced a symmetrical condition of equal shear stress on the two systems. In the 1943 Campbell Lecture,4 a slip mechanism was outlined in which the {111) planes moved step-wise in two adjacent <112> directions integrating into the <110> slip direction. "... the slipping process would be visualized as a succession of steps 30" to the right and left of the resultant, microscopically observed, slip direction; a first step setting up the twinned configuration in the single spacing involved and an ensuing slip returning the atoms to the untwinned configuration while completing a fully integrated <110> movement."4 This process is shown diagrammatically in Fig 1 which shows two close packed layers of atoms at a slip site. A movement of the full circles through the "valleys" into the adjacent sites would produce a twin configuration with respect to the open circles. The term, "twin fault," seems most appropriate to define this faulted condition of the lattice. Annealing twins in face-centered cubic metals may arise from preformed nucleii which could be described as twin faults produced by the first movement of this two stage slip process. However, it is clear that this kind of slip does not take place so as to embrace a measurable number of adjacent planes because careful X ray examination has not conclusively shown the existence of ponderable twin lamellae (as in the case of Neumann bands in the body-centered ferrite). In view of the imponderable character of these hypothetical twin faults, the search for evidence of their existence seems restricted to indirect methods. The most obvious experimental technique serving this purpose is the determination by micrographic and X ray methods of the alignment of the composition planes of annealing twins with the former slip planes in axially strained and recrystallized single crystals. In previous attempts of this sort not all of the annealing twins could be traced to slip planes known to be operative in the conventional sense and hence evidence appeared negative or inconclusive. With the discovery of additional slip systems2&apos;3 operating in conjunction with&apos; the major system of highest resolved shear stress in axially strained brass it became apparent that the simple technique outlined above might be re-employed with more gratifying results. If, on annealing single crystals of alpha brass previously strained in tension, twins are found with their composition planes parallel to all three operative slip planes and with no participation of the fourth plane there is good evidence in favor of the existence of twin faults and of the two stage slip process. Experimental Procedure and Resuits Single crystals of alpha brass of the 70-30 composition were grown by solidification from the molten state.

Jan 1, 1950

By M. King Hubbert, David G. Willis

A theoretical examination of the fracturing of rocks by means of pressure applied in boreholes leads to the conclusion that, regardless of whether the fracturing fluid be of the penetrating or non-penetrating type, the fractures produced should be approximately perpendicular to the axis of least stress. The general state of stress underground is that in which the three principal stresses are unequal. For tectonically relaxed areas characterized by normal faulting, the least stress should be horizontal; the fractures produced should be vertical with the injection pressure less than that of the overburden. In areas of active tectonic compression, the least stress should be vertical and equal to the pressure of the overburden; the fractures should be horizontal with injection pressures equal to or greater than the pressure of the overburden. Horizontal fractures cannot be produced by hydraulic pressures less than the total pressure of the overburden. These conclusions are compatible with field experience in fracturing and with the results of laboratory experimentation. INTRODUCTION The hydraulic-fracturing technique of well stimulation is one of the major developments in petroleum engineering of the last decade. The technique was introduced to the petroleum industry in a paper by J. B. Clark,&apos; of the Stanolind Oil and Gas Co. in 1948, and since then its use has progressively expanded so that by the end of 1955 more than 100,000 individual treatments had been performed. The technique itself is mechanically related to three other phenomena concerning which ah extensive literature had previously developed. These are: (1) pressure parting in water injection wells in secondary-recovery operations, (2) lost circulation during drilling, and (3) the breakdown of formations during squeeze-cementing operations, all of which appear to involve the formation of open fractures by pressure applied in a wellbore. The most popular interpretation of this mechanism has been that the pressure had parted the formation along a bedding plane and lifted the overburden, notwithstanding the fact that in the great majority of cases where pressures were known they were significantly less than those due to the total weight of the overburden as determined from its density. Prior to 1948, this prevalent opinion had already been queried by Dickey and Andresen,2 in a study of pressure parting; and by Walker,"&apos; who, in studies of squeeze cementing, pointed out that the pressures required were mostly less than those of the overburden, and inferred that the fractures should be vertical. J. B. Clark,&apos; in his paper introducing hydraulic fracturing, and later Howard and Fast," and Scott, Bearden, and Howard," also of Stanolind, postulated that the entire weight of the overburden need not be lifted in producing horizontal fractures, but that it was only necessary to- lift an "effective overburden," requiring a correspondingly lower pressure. Hubbert,7 in discussing the paper by Scott and associates, pointed out that the normal state of stress underground is one of unequal principal stresses; and in tectonically relaxed areas, characterized by normal faults, the least stress should be horizontal. Therefore, in most cases, fracturing should be possible with pressure less than that of the overburden and, moreover, such fractures should be vertical. Harrison, Kieschnick, and McGuire,8 also on the expectation that the least principal stress should be horizontal, argued strongly in favor of vertical fracturing. Scott, Bearden, and Howard6 observed that, when

Jan 1, 1958

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 8, .Article 1 of the By-laws of the Institute (see p. 45 and following pages) During 1934, sundry amendments were made for the purpose of improving the student relationship. Post-graduate students are now eligible; and the associateship can be maintained, with the payment of the regular dues of $2 per gear, for 18 months following graduation in June. A Student Associate is given a subscription to MINING A ND METALLURGY: he is accorded the privilege of getting special publications such as "The Porphyry Coppers" and "Ore Deposits of the Western States" at the reduced prices applicable to Members; he has the privileges of the Engineering Societies Employment Service and the Engineering Societies Library; and he is not only invited but urged to attend all meetings of the Institute, its Divisions and its Local Sections. The Institute wants to extend the hand of professional fellowship to students following mineral industries curricula.

Jan 1, 1936

. S. W. PARR, * Urbana, Ill. (written discussion ? ).-Multiplication of argument is unnecessary to establish the desirability of coking coals at low temperatures, that is to say, below 1200° F. The value of the semi-coke thus produced would doubtless go far toward solving the problem of smoke prevention, and suggests the possibility of the substitution of a smokeless fuel for anthracite and so-called smokeless coals. Whether such coke would have any value as metallurgical coke is a question which cannot be answered for lack of any experimental data in the use of such material. Of course interest is accentuated, at the present time, in the amount and character of the tars, which promise greatly to exceed in values the products obtainable from. the high-temperature process. The difficulties encountered in adapting the principles of low-temperature carbonization to industrial methods are well nigh insurmountable. Briefly stated, there is involved the heating of the center of a mass of non-conducting material by the external application of heat. It is a well established fact that the center of the mass of coal in a standard

Jan 11, 1918

By J. E. Papin

Morenci ores contain as an average about 0.015 pct molybdenite, MoS2. Incidental to the concentrating operations applied for the recovery of copper minerals, approximately two-thirds of the molybdenite is floated and appears in the final copper concentrate. The economic importance of molybdenum and the success achieved in its recovery in milling operations elsewhere encouraged research directed toward its recovery in marketable form. Several procedures are utilized to effect separation of molybdenite from copper and iron sulphides, but only two have wide application. In the better known of these two methods the molybdenite in the copper concentrate is depressed in a flotation operation using soluble starch as the depressant. The tailing from this treatment thus becomes a low-grade molybdenite concentrate which after thickening, filtering, and low temperature roasting is repulped with water and subjected to additional flotation steps for recovery of the molybdenite. A thio-phosphate collecting agent is employed in flotation of the copper minerals. Presumably the stability and lasting effects of that collector type necessitated the practice of depressing molybdenite followed by subsequent roasting to insure elimination of copper and iron sulphides from final molybdenite concentrate.

Jan 2, 1955

By S. O. Reichert

The nuclear industry has made a considerable effort to reduce environmental pollution with the result that knowledge in the field of radioactive waste management is well advanced. An example of the methods used for radioactive waste disposal is provided by the Savannah River Plant (SRP) operated by E. I. du Pont de Nemours & Co. for the AEC. It occupies an area of 320 sq mi along the Savannah River downstream from Augusta Ga., and has production facilities that include a fuel preparation area, three reactor areas, two chemical separation areas (F and H), and a heavy water plant. Gaseous, Liquid and Solid Radioactive Wastes Are Handled During Disposal The primary sources of radioactive waste are the reactor and chemical separation facilities. The reactors are cooled and moderated by heavy water which, in turn, is cooled by river water in heat exchangers. This arrangement prevents irradiation of the river water so that radioactivity is not discharged into the river water except when small quantities of moderator are lost by heat exchanger leaks. Because of the high cost of heavy water, these losses must be kept to a minimum.

Jan 9, 1968

By J. Th. G. Overbeek, R. Schumann, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.1-3 Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles.

Jan 5, 1954

By John G. Roscoe

Continental Materials Corp. operates two under- ground uranium mines in the Crooks Gap district of central Wyoming. Both mines are developed as slusher mining operations through vertical shafts with single level haulage to slusher pocket loading stations. In general, operations at both mines are similar except for depth and some minor details. The shafts are identical in cross-section, each with a 4 ½ x 5-ft hoisting compartment and a 4 ½ x 5-ft manway. Kimberley-type skips are loaded from measuring pockets through air-operated guillotine gates. The Seismic shaft is 245 ft deep and the Reserve shaft depth is 585 ft. The Seismic shaft was sunk in 1957 and the mine has been producing 200 tpd since 1958. The Reserve shaft was sunk in 1960 and the mine is still in the development stage. The hoists of both mines are equipped for semi-automatic operation; that is, they are mechanically controlled to perform a certain cycle of duty and then stop until another cycle is manually initiated. The Seismic hoist, however, was originally a conventional, manually controlled unit; the reserve hoist was installed as an automated system.

Jan 7, 1962

By R. L. Templin

THE modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 lb. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately correct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements.

Jan 1, 1930

By J. D. MacKenzie

THE world production of copper for the first eight months of 1927 shows an increase of 3 per cent over the same period in 1926. Since February of this year, however, production has been considerably curtailed. The United States reduction in the last four months has been offset by the increased South Ameri-can and Belgian Congo production. The United States is now producing 58 per cent of the world production, Chile and Peru 17.3 per cent, Belgian Congo 5 per cent. In 1926 the United States produced 54 per cent, Chile and Peru 16.3 per cent, Belgian Congo 6.3 per cent. Production, Tons 1917-largest war year 1,580,000 1925 1,581,000 1926-increase 3 per cent 1,628,000 1927-increase 3 per cent 1,670,000 Copper Producing Countries, 8 mo., 1927: Tons Per Cent United States 644,000 58.0 Chile and Peru 192,000 17.3 Europe 90,000 8.1 Belgian Congo 56,000 5.0 Japan 46,000 4.1 Mexico 30,000 2.7 Canada 23,000 2.1 Figures are not available for Spain and Portugal, which would probably precede Mexico.

Jan 12, 1927

By Robert L. Russell, Henry W. Zimmerman

The Bunker Hill mine in the Coeur d&apos;Alene mining district at Kellogg, Idaho, has been a major producer of Pb-Ag-Zn ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones and now covers an area approximately 1 mi long by 0.5 mi wide. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Ore production is presently at the rate of about 1700 tpd. A 2-mi adit, the Kellogg tunnel, at the 2500 elevation provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft. 50º-inclined shaft extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for main line track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical ft apart. Also, many intermediate levels exist throughout the mine.

Jan 1, 1971

By Daniel L. Murphy

The iron ore province of Quebec and Baffin Island trends from the southern shore of Baffin Island northeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands, but future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. GENERAL LITHOLOGY Pleistocene and recent deposits of clay, sand, gravel and erratic boulders cover roughly 60% of the land surface. All of the bedrock is of Precambrian age (Table I). Paragneisses and paraschists together with metasedimentary iron-formation, marble and quartzite are abundant and, for the most part, appear to be metamorphic equivalents of the relatively unmetamorphosed rocks of the Labrador Trough to the north beyond the "Grenville Front." Bodies of amphibolite are widely scattered. A large portion of the metamorphic rock shows some degree of permeation by granite material as well as alteration by hydrothermal solutions. The youngest bedrock consists of a complex containing slightly altered ultramafic to monozonitic intrusives.

Jan 9, 1962

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By T. A. Read, M. S. Wechsler, D. S. Lieberman

IN the formation of martensite in steel, it has been observed that the habit plane does not change continuously as the alloy content is varied. Instead, it appears that discrete habits correspond to certain ranges of composition. Greninger and Troiano&apos; found that in low-, medium-, and high-carbon steels, the habits are approximately (1l1), (225), and (259), respectively.* The work of Mehl and Van Winkle2 indicated that the change from the (225) to the (259) habit is fundamentally a consequence of the lower transformation temperature rather than the higher carbon content. Also, Otte and Read3 observed that the habit plane orientation for a chrome-carbon steel scattered within a cone of semivertex angle of 5 deg, which was outside of the experimental error in the determination of the habit plane. These observations suggest the importance of investigating what factors in the crystallography of the formation of martensite account for the several types of habit and the inherent scatter in the precise orientation of the habit plane. A theoretical treatment of the austenite-martensite transformation has been given,4 which considers the total transformation distortion to be composed

Jan 1, 1961

I. THE ENERGY CRISIS STILL EXISTS A. ALTHOUGH IMMEDIATE SHORTAGE IS NOW ALLEVIATED BY: 1. Increased imports through lifting of Arabian embargo; a. Imports were 6.5 million bpd during the week ended January 17, or 1.3 million bpd higher than last year. b. 1.7 million bpd higher than March &apos;74. 2. Decreased demand resulting from higher prices and conservation. a. January 1975 demand was 17.9 million bpd, 0.1 million bpd lower than January 1973 and … b. 2.0 million bpd, or 10% under originally projected demands for January 1975. c. Gasoline (excluding tax) went up 59% from 27d/gal in August 1973 to 43c/gal in September 1974. d. Gasoline demand for January 1975 was 6.3 million bpd, 0.1 million bpd higher than 1973 but 0.7 million bpd ( 10% ) under projected demand. 3. Increased crude and major product inventories. a. January 17, 1975 crude and major product inventory was 794 million bbl, 99 million bbl higher than the same date in 1973. b. 105 million bbl increase since April 12, compared to only 38 million bbl increase during the same period in 1973.

Jan 5, 1975

Within the last century, and largely during the latter half of it, the increase of our knowledge of the development of man, both in his search for a livelihood and for power, and in the growth of his reason and conscience, has been greater than all we had known before. The great interest in all kinds of archaeological work and the many excavations made of buried and long forgotten places has put at our disposal historical records not available, and in many cases not known before, and a study of these and other records of human progress from paleontological and geological sources has given us a much broader view of what we call "civilization" than was possible even a short time ago. The old idea that men were created with fully developed minds, speech and reason has yielded to the view that in the upward progress of the human race the development of the mind and reason has been a comparatively recent occurrence, as we think of the half million, and probably more, years that have passed since our earliest records of man were made. The traits that come to us without effort

Jan 1, 1935

By Samuel Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study. and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main, system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change.

Jan 1, 1928

Within the last century, and largely during the latter half of it, the increase of our knowledge of the development of man, both in his search for a livelihood and for power, and in the growth of his reason and conscience, has been greater than all we had known before. The great interest in all kinds of archaeological work and the many excavations made of buried and long forgotten places has put at our disposal historical records-not available, and in many cases not known before, and a study of these and other records of human progress from paleontological and geological sources has given us a much broader view of what we call "civilization" than was possible even a short time ago. The old idea that men were created with fully developed minds, speech and reason has yielded to the view that in the upward progress of the human race the development of the mind and reason has been a comparatively recent occurrence, as we think of the half million, and probably more, years that have passed since our earliest records of man were made. The traits that come to us without effort

Jan 1, 1939

By Hugh J. Leach, J. C. Van de Water

In open pit mining, as in other industries, it has I become necessary to improve operating efficiency in order to combat higher labor and supply costs. Moreover, orebodies are becoming leaner, pits are getting deeper, stripping ratios are increasing, and hauls are getting longer. There has been a steady increase in size, speed of operation, and reliability of the various machines involved in breaking, loading, and hauling ore. Changes have seldom been radical but are rather the result of steady improvement. Drilling: Notable advances have been made in the use of rotary drills and air powered percussion drills for blasthole drilling. Several hundred of these machines are now in use as replacements for churn drills in softer rocks such as limestone and shale. Their application to hard rocks such as iron ore and taconite is under current investigation, but in the Lake Superior iron mining district, open pit blast-hole drilling in ore has been accomplished almost exclusively by standard churn drilling. The only recent advance has been the use of larger machines drilling 9-in. holes. This has increased drilling speed somewhat and allowed wider hole spacing, with consequent cost reduction.

Feb 1, 1956

By J. J. Gilman

IT is well established that dislocations exist in crystals and account for crystal plasticity.&apos; However, the origins of the dislocations are not clear. Among the means by which dislocations might originate are: a) through crystal growth accidents, b) by the collapse of condensed sheets of vacancies, or c) by stress-induced nucleation. Theoretical calculations&apos; have indicated that the last means should require very high stresses in order to operate. The purpose of this paper is to show that the stresses around the tips of cracks are large enough to nucleate large numbers of dislocation loops. Specifically, it will be shown that (100) cleavage cracks in LiF crystals nucleate dislocations in regions of the crystals where dislocations did not exist previously. It is believed that the use of LiF for this investigation does not restrict the significance of the 1 results. In fact, it is believed that this complements and extends previous papers by the same author which dealt with metal crystals.10,14 The dislocations were detected by means of the etching techniques that were described in a previous paper by Gilman and Johnston.3 In that paper it

Jan 1, 1958