Search Documents

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By Robert Linton

THE PURCHASE of silver by the United States Government under the provisions of the Pittman Act is practically completed. Producers of silver in this country will now have to market their silver in competition with the rest of the world. It therefore becomes of interest to study such data as are available and endeavor to obtain such suggestions as may be afforded therefrom as to the probable future market position of the metal. Conditions influencing the marketing of silver are numerous and complex. It is a commodity entering. into the arts and manufactures, and therefore influenced by the condition of various lines of business which make use of it; it is currency-being used by all countries for subsidiary coins and even as the founda-tion of the system by a very few; and it serves as a frequent basis for speculation. The various factors involved can easily set up so many cross-currents in the flow of the metal that predictions in regard to the market position of silver can never be safely made, although it may be possible to form some idea of prob-able trends over a sufficiently long period. Of course price is determined, as is the case with all commodities, by the inexorable workings of the law of supply and demand.

Jan 6, 1923

By John W. Cahn, David A. Karlyn, Morris Cohen

The massive B(bcc) — am (fcc) transformation in Cu-Zn alloys has been studied isothermally by pulse-heating the retained ß phase from room temperature to the reaction temperatures. The transformation is found to occur only in the single-phase a region of the equilibrium diagram. The massive growth rate is of the order of 1 cm per sec and is constant at each temperature, usually after a delay time of some milliseconds. The delay time depends on the reaction temperature in C-curve fashion, while the growth rate increases monotonically with temperature over the single-phase range. The absence of isothermal massive transformation in the two-phase region does not arise from slow growth rates at such temperatures, but because the reaction cannot get started there. It is proposed that the massive transjormation initiates at small preexisting a particles which have rejected zinc into the surrounding 0 matrix. Only within the single-phase region can these particles consume the excess zinc during diffusion-controlled growth and thereby accelerate to the steady-state massive growth rate. The onset of massive growth marks the end of the delay time, and the growth rate then becomes interface-controlled. These isothermal transformation characteristics explain why the usual composition range for massive-kinetic studies by quenching is so limited. The same principles can be extended to more complex alloy systems by recognizing that the single-phase region in which the massive transformation can occur may not be stable with respect to phases not participating in the reaction. MASSWE transformations are now recognized as a regular class of solid-state reactions involving no compositional change (like martensitic transformations) and no shear displacements (unlike martensitic transformations). The name was first coined by Greninger1 in 1939 to describe the coarse grains of fcc a solid solution generated via a fast reaction from the parent bcc 0 solid solution in Cu-A1 alloys. However, some 9 years earlier, phillips2 had already described a similar transformation in the Cu-Zn system. The fact that the massive a formed as a single phase during drastic quenching from the 0 region of the equilibrium diagram signified that compositional changes were precluded. and the reaction was presumed to take place as in a one-component polymorphic transition by nucleation and growth. Phillips also observed that the occurrence of the massive transformation in the Cu-Zn system was extremely sensitive to alloy composition. For example. in a Cu-37.3 at. pct Zn alloy. the ß — am (am = massive transformation product) reaction was found to predominate and was not suppressed by iced-brine quenching from the 0 region. whereas at compositions greater than 38.3 at. pct Zn the massive reaction did not appear at all. Knowledge concerning massive transformations has bee11 substantially enhanced over the years by Massalski and his coworkers; an excellent summary of his papers and the current understanding of this type of reaction has been published recently by Barrett and ~assalski." he massive transformation product grows in roughly nodular form. often with irregular boundaries but sometimes with almost planar interfaces. The latter may have simple crys-tallographic indices relative to the 0 matrix. or the indices may be complex just as in the case of mar-tensites.'1 Little is known about the existence of orientation relationships between the massive and parent phases. A striking feature of massive transformations is that the massive units start almost exclusively at grain boundaries of the parent phase and frequently propagate on a broad front across matrix grains and grain boundaries of various orientations. Because of the rapid growth rate, it is thought that the interface motion is controlled. not by long-range diffusion. but by thermally activated atom jumps across the transformation boundary.

Jan 1, 1970

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By M. E. Bell

The term "operational research" was probably first used to describe work started under E. C. Williams, now Director, SHAPE Air Defense Technical Center, late in 1937 or 1938, at the Bawdsey Research Station of the British Air Ministry, a laboratory center concerned with the development of radar equipment. After the practicability of the early techniques had been demonstrated, a large (for those days) program of development and installation was authorized. It was very soon realized, both by the Royal Air Force and by the scientists that almost as important as the gear itself was the way in which it should be used. Accordingly, it was decided that some scientists should cooperate to study the way in which the equipment should be deployed and operated in conjunction with the Royal Air Force. To distinguish this work from the normal work of a research and development establishment, the term "operational research" was coined. It merely meant at this time that this particular section of scientists was to be concerned with the use of the gear rather than with its technical development and it seemed natural to those concerned to adopt the word "operations" which has a specific connotation in the armed forces.' This method was later extended to peacetime business enterprise, government operations and other human activities. Operations research appears to have penetrated the extractive industries more slowly and less completely than other industries, the military, or the government. This may be due (1) to a difference in the attitude of management towards operations research, or towards research of any kind, for that matter; (2) to unsuitability of the extractive industries for application of the operations research method; (3) to inaccessibility of the data; (4) or to a lack of trained personnel who are interested in applying operations research to the mineral industries.

Jan 8, 1963

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By Robert H. Leach, C. H. Chatfield

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a stand¬ard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By W. T. Malone, J. R. Williams, R. L. Tiner, J. M. Tinsley

Hydraulic fracturing methods for production stimulation have become a common procedure in the oil and gas industry. Fracturing treatments are performed on wells of various potentials to help increase the production rate. In addition to the desire for increased production is the need to predict what increase might be expected. This knowledge is useful in economical treatment planning to accomplish the desired production goals for the well. Theoretical production increases due to horizontal radial fractures may be calculated using equations developed from mathematical analyses and electrical models.1,2,6 It also is possible to predict theoretical production increases due to vertical fractures using curves developed from electrical3 and mathematical models.8 However, these studies assumed that the vertical fracture height and the formation height were equal, which may not be true." In addition, the final fracture height through which fluid is produced may not be equal to the created height. The development of vertical fracture proppant transport relationships has made unrealistic the assumption that propped fracture height is equal to created fracture height. Through the use of published proppant transport equations,4'12 it is possible to calculate the height of a bed of propping agent deposited in a fracture of a given height. Assuming that the fluid flowing in the fracture moves through only the propped portion of that fracture (i.e., that the un-propped part of the fracture heals) it becomes essential to know how production increase varies with the ratio of propped fracture height to formation height. It should be recognized that future investigation may determine that the fracture does not heal completely and that a highly permeable channel exists over the deposited bed of proppant. The effect of this channel was not considered for the present study. The following analysis of experimental data allowed development of curves to determine theoretical production increases considering fracture height as a variable. Discussion In designing a fracturing stimulation treatment a number of variables must be considered. The size of the treatment, type of proppant used, proppant concentration, treatment fluid properties and well conditions are all factors affecting the dimensions and permeability of the fracture. Production increase due to a vertical fracture is affected by propped length, height, width and permeability of the fracture for a given set of formation conditions. Production increase may be defined as the ratio of production rate after fracturing to the production rate before fracturing at the same pressure differential, pe — pw. The producing rate in an

Jan 1, 1970

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By AIME AIME

The first session, held Tuesday evening, February 23, in North Sheffield Hall, was called to order by Louis V. Pirsson, Chairman of the Local Committee, who introduced Prof. Russell H. Chittenden, Dean of the Sheffield Scientific School of Yale University. Professor Chittenden, in behalf of the Governing Board, felicitated the Institute on its visit to New Haven, and cordially welcomed the members and guests to the University and the city. Dr. James Douglas, who presided at the meeting, responded in behalf of the Institute. The Secretary announced that, upon the proposal of many members, the unanimous report of the Committee on Membership, and .the unanimous recommendation of the Council, the following members had been unanimously elected by the Board of Directors Honorary Members in the American Institute of Mining Engineers Prof. Richard Beck, of Freiberg, Saxony, in recognition of his distinguished service to technical literature, and the cordial

Apr 1, 1909

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non-metallic inclusions seems to be satisfactory and adequate. NATURE AND CONS1lTUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1964

By Nelson P. Hulst

COMMITTEES. DULUTH.-Nelson P. Hulst, Chairman; J. B. Adams, W. C. Agnew, M. H. Alworth, C. W. Andrews, R. Angst, William R. Appleby, C. E. Bailey, G. G. Barnum, E. F. Bradt, Mylie Bunnell, George L. Cheesebrough, Peter Christen¬sen, F. A. Cokefair, T. F. Cole, C. A. Congdon, N. Cowling, George H. Crosby, M. D. Cullum, C. d'Autremont, Jr., H. L. Dresser, C. T. Fairbairn. Walter Fitch, F. L. Gilbert, J. T. Hale, G. G. Hartley, E. B. Hawkins, M. S. Hawkins, J. H. Hearding, Louis Hill, L. J. Hopkins, F. E. House, J. C. Hunter, 0. D. Kinney, J. W. Kreitter, E. J. Longyear, Alexander McDougal, W. A. McGonagle, A. M. Marshall, W. N. Merriam, T. D. Merrill, John Millan, P. Mitchell, Clarence Moore, Hon. Page Morris, C. H. Munger, Henry Nolte, W. J. Olcott, A. L. Ordean, Thomas Owens, F. A. Patrick, H. M. Peyton; D. M. Philbin, Capt. Charles Potter (U. S. A.), L. W. Powell, Harry Roberts, Louis Rouchleau, George A. St. Clair, J. U. Sebenius, Joseph Sellwood, Amos Shepherd, W. B. Silvey, George Spencer, George C. Stone, H. B. Sturtevant, George D. Swift, Kirby Thomas, C. D. Thompson, A. D. Thomson, G. A. Tomlinson, Charles Trezona, R. R. Trezona, Maj. J. H. Upham, Charles Van Barneveld, W. W. Walker, J. L. Washburn, A. C. Weirs, H. J. Wessinger, A. B. Wolvin, Dwight E. Woodbridge. HOUGHTON.-W. E. Parnall, Chairman; W. D. Calverley, Secretary; W. B. Anderson, L. S. Austin, Jacob Baer, William Bath, F. J. Bawden., Simon Beahan, John Been, C. H. Benedict, Walter Bloomfield, S. H. Brady, Samuel Brady, Henry Brett, A. L. Burgan, F. I. Cairns, W. H. Cake, Arthur L. Carnahan, William Carpenter, Phillip Carroll, John J. Case, T. L. Chadbourne, W. A. Childs, B. F. Chynoweth, Captain James Chynoweth, H. P. Clausen, F. G. Coggin, H. D. Conant, J. B. Cooper, J. R. Cooper, John Cuddihy, Thomas Cummings, Robert Davidson, J. B. Dee, J. R. Dee, T. S. Dee, Theodore Dengler, M. M. Dennis, Captain Thomas Dennis,. F. W. Denton, A. D. Edwards, R. M. Edwards, C. S. Fales, Daniel Fisher, Henry Fisher, James Fisher, A. L. Floeter, Frank H. Getchell, M. C. Getchell, W. M. Gibson, W. M. Gilliland, James G. Glanville, George Goodale, H. S. Goodell, A. R. Gray, Edward Grierson, Homer Guck, H. D. Haddock, Captain Josiah Hall, John L. Harris, Captain S. B. Har¬ris, Enos Harrold, F. William Hartmann, George L. Heath, C. M. Hoar, Thomas Hoatson, 0. P. Hood, Captain Thomas Hooper, Captain Joshua D. Husking, Dr. L. L. Hubbard, Arno Jaelinig, E. D. Johnson, G. A. Koenig, Edward Koepel, C. H. Krause, R. H. Leach, A. W. Leonard, James MacNaughton, Edward McCormick, Thomas McDonald, R. T. McKeever, F. W. McNair, James McRae, John Mackey, John C. Mann, Major G. A. Marr, Captain Thomas Maslin, Harry Mercer, James Merton, Michael Messner, William F. Miller, Captain J. Milligan, Dr. J. W. Moore, Charles H. Moss, H. F. Nickerson, Charles L. Noetzel, P. H. Paine, John Penrose, Captain John Pentecost, Graham Pope, R. C. Pryor, James Ramsay, J. T. Reeder, Allen F. Rees, J. H. Rice, W. G. Rice, James

Jan 1, 1905

THE solid nonmetallic inclusions that are present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and. this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general the term "nonmetallic inclusions" seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those that occur as a result of reactions taking place in the body of the molten or solidifying metal and (2) those that result from the mechanical incorporation of refractories or other materials with which the steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulphidea but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from the molten or solidifying steel may be caused by (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change in equilibrium constants as the steel cools to the freezing temperature, (4) decreased solubility with lower

Jan 1, 1944

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By AIME AIME

GENERAL COMMITTEES. SAN FRANCISCO:-ExECUTIVE, Hon. William C. Ralston, Chairman; RECEPTION, Prow. Samuel B. Christy, Chairman; SESSIONS, Frederic W. Bradley, Chairman; PRESS, H. Foster Bain, Chairman; FINANCE, Mark L. Requa, Chairman; EXCURSIONS AND ENTERTAINMENTS, Edward H. Benjamin, Chairman. Assisted by Harry P. Stow, C. W.Merrill, F. W. Griffin, Gelasio Caetani, Albert Burch, Newton Cleaveland, Corey C. Brayton and R. E. Cranston. Los ANGELES :-EXECUTIVE, Theo. B. Comstock, Chairman; R. W. Hadden, Secretary; H. R. Simpson, Treasurer. Institute Headquarters at Hotel St. Francis. The first and opening session, held Tuesday afternoon, Oct. 10,. in the Reception-Hall of the St. Francis, was called to order by State Senator William C. Ralston, Chairman of the Executive Committee, who in a few well-chosen words welcomed the visiting members and guests of the Institute to San Francisco. He said it was twelve years since the last meeting on the Pacific Coast and that it was here that the greatest feats. of mining had been accomplished in the history of the country. He told of the work that had been done on the continent and of the new methods introduced by the mining engineers for the betterment of the nation. He then introduced Capt. Robert W. Hunt, twice past President of the Institute, and present Acting President for the San Francisco meeting and the subsequent visit to Japan, who responded cordially to Mr. Ralston's welcoming address. By unanimous vote, the Secretary was instructed to send a telegram to President Charles Kirchhoff expressing regret for his absence, and hoping for a rapid improvement in the health of his mother. The following papers were presented in brief oral abstract by the authors: . * Electrolytic Refining at the U. S. Mint, San Francisco, Cal., by Edward B. Durham, San Francisco, Cal. The Parral Tank System of Agitating Slime-Pulp, by Bernard MacDonald, Guanajuato, Mexico. * The Newport Iron-Mine, Ironwood, Mich., by B. W. Vallat, Ironwood, Mich. (illustrated by lantern-slides). * Distributed in pamphlet worm.

Nov 1, 1911

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

By R. J. Charles

F. C. Bond: This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = —Cdx/x [1] either Corn must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant. According to the Third Theory, in the general case n is a constant equal to 3/2, and C is a variable related to the work index Wi. If x is placed equal to P (the size in microns which 80 pct of the product passes) and F is the size 80 pct of the feed passes, then C equals 5 W1, and dE = 5 -5 Widx/x = 10 Wi 10 Wi w = vP vF which is the basic equation of the Third Theory. It is apparent that this integration involves the error of treating the parameter Wi as a constant, just as the author's treatment involves the error of integrating his variable n as a constant. These errors are probably relatively unimportant, considering the small range of the variables. When more is known about the factors contained in the work index, Eq. 1 can be revised as a partial differential equation. The Third Theory exponent of 1/2, or n = 3/2 in the Charles' differential equation (Eq. l), was not chosen primarily because it is the average between the Kick and Rittinger exponents; this may be merely fortuitous, since it is illogical to define truth as the average between two errors. It was first discovered from the study of a large mass of crushing and grinding data and confirmed by laboratory testing. The general correspondence of the Third Theory equation to actual crushing and grinding results over the entire size reduction range argues strongly that a fundamental phenomenon is involved. The a posteriori theoretical explanation of the constant Third Theory exponent is that the work done in breaking rock is proportional to the length of the crack tips formed. Compressive force applied to the rock results in deformation and strain energy. When this locally exceeds the breaking strength a crack tip forms, the surrounding strain energy flows to the crack tip and extends it to split the rock, with release of the energy as heat. Under rapid impact the crack tip may form before the strain has reached equilibrium, resulting in less energy expenditure and probably a coarser product. In any case, the elastic limit of a brittle material is practically the same as its breaking strength, and the work necessary to form the crack tip is the work required to break. The crack length of a ton of broken rock cannot be measured directly. However, the particle shapes of feed and product are similar, and the crack length is considered equal to the square root of one half of the new surface area formed. It is, therefore, proportional to 1/vD, where D is the equivalent product particle diameter. This is the basis of the Third Theory equation. Many secondary factors can be imposed upon the crack length breakage. These may cause the Third Theory work index to increase or decrease somewhat as the product size becomes finer. The work index is properly a parameter rather than a constant, making it an increasingly valuable practical criterion of the work input required in crushing and grinding.

Jan 1, 1959

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957