Search Documents

By C. P. Gazzara and

The modulus of elasticity and yield strength of commercially pure, annealed titanium sheet was investigated at room temperature as a function of strain rate and direction of loading. The value of E varied with direction of measuremeni in the sheet but was unaffected by strain rate in the range 0.04 x 10-to 10-2min-1. The yield strength increased with increase it2 strain rate and varied with specimen orientation. VALUES of the modulus of elasticity, E, in tension for commercially pure titanium have been reported at from 14 to 20Xl06 psi.' Reasons suggested for this variation have been a) composition, b) strain rate, c) texturing, and d) creep. For example, alloys of titanium with aluminum, manganese, and nitrogen have yielded modulus values of from 12.5 to 16.8 x lo6 psi at room temperature.' It was shown by Klier that the modulus in titanium plate was sensi-tive to strain rate. while Dotson and kattus meas- ured variations in E as the strain rate was increased from 3X to 60 min-l. For RC-7OA, 0.040-in. titanium sheet at room temperature Dotson and Kattus found that the average values of E, for specimens in the rolling direction, increased from 14.7 to 16.0 X lo6 psi as the strain rate increased. Simultaneously, the 0.2 pct yield strength increased from 74,700 to 95,700 psi for the same specimens. Differences in yield strength and E have been reported as a function of directionality in titanium sheet.= Dotson and Kattus report such an effect, and Feola6 found in annealed titanium sheet marked anisotropy in tensile strength, yield strength, reduction in area and elongation at room temperature, with

Jan 1, 1961

By B. D. Cullity, J. T. Norton, M. Telkes

THIS investigation of antimony-selenium alloys was undertaken in an attempt to find a suitable material for use in power-generating thermocouples. The chief requirements for such a material are high thermoelectric power, low electrical resistivity and low thermal conductivity. Measurements of the first two properties mentioned are usually sufficient to determine whether or not a material is suitable for use in a thermoelectric generator. As a first approximation the requirements are: 1. Thermoelectric power greater than 200 microvolts per °C. 2. Electrical resistivity less than 0.002 ohm-cm. 3. Thermal conductivity less than 0.015 watt per cm per "C. These quantities are averages for the Operating temperature range. Previous Work Experimental investigations of equilibrium in the antimony - selenium system have been summarized by Han-sen². These investigations extended from 1906 to 1921. In Hansen's judgment, the most accurate phase diagram is that determined by Parravano, in 1913 and this is reproduced in the upper part of fig. 1. The most notable parts of this diagram are the liquid miscilibility gap, extending from about 12 to 36 wt pct selenium, and the intermediate phase Sb2Se3 containing 49.3 wt pct selenium. The crystal structure of Sb2Se3 has not been determined. Pelabon3,4 made measurements of the electrical resistivity of a few antimony-selenium alloys but his investigation was not very complete. He found that the resistivity increased with the selenium content and became very large as the composition of Sb2Se3 was approached. For alloys containing less than 50 at. pct (39.3 wt pet) selenium, he found that the resistivity increased regularly with temperature. For alloys containing larger amounts of selenium, he found various results: in some cases, the resistivity decreased with increas-

Jan 1, 1951

By V. Lepetic, C. C. Harris

A systematic program of investigations covering all aspects of cell hydrodynamics,1-3 flotation kinetics,4,5 surface chemistry and their interactions has as a major objective the elucidation of the flotation micromechanism and the principles of cell design and scale-up.6 Purely from the scale-up point of view, a family of reactors should enable different throughputs of the same material to be similarly treated or, at least, to be treated in a manner which differs beween reactors in a predictable way. Thus, for the same material and residence time, the recovery and grade from differently sized cells of the same family should, ideally, be similar or, at least, be related to each other in a known way. It is well known, however, that different-sized cells do not always achieve similar results, and it is necessary to enquire into the reasons for these differences. For example, it may be that the relative dimensions of different-sized cells result in hydrodynamic conditions which preclude similarity; if so, different scaling may improve the situation. The major question concerns identifying the dynamic conditions and their associated geometric requirements which govern the flotation process, and the criteria which are necessary for their fulfillment. It is to answer such questions that the program referred to earlier was instituted. In connection with this program and in order to examine data concerning the physical features and operating conditions of existing flotation cells, the following survey was carried out. This work represents an approach which is complementary to experimental investigations, for it recognizes that the design of existing cells may embody several of the principles being sought. If data for enough cells, especially families of cells, are examined, some broad requirements common to all cells may emerge.

Jan 9, 1966

By J. E. Burke

THE origin of so-called annealing or recrystalli-zation twins in face-centered-cubic metals continues to be a matter for speculation, and in the present report an attempt is made to explain their origin and to account for at least a majority of the observations concerning their behavior. The fact that annealing twins are prominent only The speelmen was deformed 8 pet in compression and then indented over the lower left-hand corner in a Rockwell in-denter, and then annealed to cause partial recrystallization. Note intense twinning in heavily deformed part and slight twinning in less deformed part. The upper right-hand corner is unrecrystalized. Area reduced approximately 25 pot for reproduction. after recrystallization suggests that deformation may be necessary for their formation. In 1926, Mathewson1 reported the observation by Phillips that annealing twins are frequently parallel to strain markings which delineate octahedral planes in the deformed (and partially recrystallized) matrix, and suggested that strain markings are mechanical twins which grow into annealing twins during recrystallization. Later work by Burke and Barrett' has shown that strain markings are traces of planes upon which slip has occurred, and that there is no evidence for the formation of mechanical twins of microscopically resolvable width in face-centered-cubic metals. Mathewson3 has pointed out, however, that slip may produce twin faults, and later modifications of this hypothesis have assumed that twin faults rather than true mechanical twins serve as the nuclei for annealing twins. Carpenter and Tamura5 suggested, also in 1926, that annealing twins might form by accidents of growth. A close-packed layer of atoms can be added to the octahedral plane of a face-centered-cubic metal in two possible positions, the right position

Jan 1, 1951

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By Boyd Dudley

THE material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridizing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. The object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value.

Jan 12, 1914

By D. A. Martin, Laird Crocker, W. I. Nissen

The Federal Bureau of Mines has developed a process for removing SO2 from stack gases. The process comprises absorption of SO2 in an. aqueous solution of sodium citrate, citric acid, and sodium thiosulfate, followed by reaction of the absorbed SO2 with H2S to precipitate sulfur and regenerate the citrate solution for recycle. A pilot plant was operated at The Bunker Hill Co. lead smelter in Kellogg, Idaho, to assess the feasibility of using the process for flue gas desulfurization. Nominal capacity of the pilot plant, which treated .tail gas from the lead smelter sintering furnace, was 1699 standard meters cubed per hour (15 degrees celsius) of 0.3- to 0.7-percent-SO2 gas yielding about 272 net kilograms of sulfur per day. The pilot plant was operated for about 4500 hours and produced more than 45 net tonnes of sulfur. The operation demonstrated that (1) more than 95 percent of the SO2 could be removed from the lead smelter sintering furnace tail gases, (2) regeneration of the citrate solution with H2S and precipitation of sulfur in conventional stirred vessels was readily controlled and highly efficient, (3) the precipitated sulfur could be continuously recovered as a 99.5-percent-pure product by kerosine flotation and melting, and (4) the 77- to 79-percent-H2S gas used for sulfur precipitation could be readily produced from pilot plant product sulfur, natural gas, and steam. Projected operating costs, including capital charges, for a citrate plant, installed at a 118 000-tonne-per-year lead smelter and treating 49 271 standard meters cubed per hour of lead smelter sintering furnace tail gas, are estimated to be $384 per tonne of sulfur.

Jan 1, 1976

MAJOR AWARDS JAMES DOUGLAS GOLD MEDAL 1960-Augustus B Kinzel "For outstanding contributions and inspiring leadership in the field of electrolytic and electrothermic winning of nonferrous metals and for his notable administrative ability " BENJAMIN F FAIRLESS AWARD 1960-Charles McElroy White "His ability, energy and determination in starting the top-pressure blast furnace and foresight in providing it with prepared burdens have created the world's dominant metal producer " HAL WILLIAMS HARDINGE AWARD 1960-Samuel H Dolbear "Eminent mineral consultant and engineer-first chairman, Industrial Minerals Division of AIME-first editor, 'Industrial Minerals and Rocks'-for the improvement and increase of industrial mineral knowledge "

Jan 1, 1960

By Robert H. Richards

While yet in correspondence with the heads of the several mining schools for the purpose of bringing the details of my Address into the best form for publication, a severe illness overtook me, and before I had recovered sufficiently to turn my attention to matters of this character the Address had been printed in its imperfect form for volume xv. of our Transactions, and the type had been distributed. The incorporation of the later corrections, in the form of a Supplement, became a necessity. To simplify the corrections as much as possible to the reader, every paragraph which has been revised in any way is here reprinted in full.

Jan 1, 1887

By John Birkinbine

In a former paper* attention was directed to the various forms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal fnrnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillatinig engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter

Jan 1, 1879

By E. P. Pfleider, O. Rellensmann

For many years mine surveyors and exploration engineers have sought an accurate means of transferring meridian underground by using the gyro-compass. These efforts have generally failed, either because they were inaccurate or because the size and cost of the unit were prohibitive. During the past ten years, however, great strides have been made. Autonetics in California has developed a comparatively light-weight (100-lb) gyro-theodolite, and the Institute for Mine Surveying at Clausthal Mining Academy in Germany has developed an instrument that is accurate to within 20" to 30" of arc. Concurrently, Minneapolis-Honeywell has produced an astounding gyro, the size of a salt shaker, that weighs less than 0.5 lb and compares favorably in performance with the 50-lb gyros of conventional design. This unit, designed for missile guidance, should be adaptable for surveying small boreholes. Given the proper interest and approach from the engineering fraternity, excellent gyrocompasses could probably be available for accurate underground survey work at nominal cost within the next three years. Principles of the Gyro-Compass: The gyrocompass, used for 50 years as a navigational instrument in ships and aircraft, senses the turning axis of the earth and points out true polar north. It does this by employing the earth's rotation, the force of gravity, and the precession characteristics of a gyro. For further details the reader is referred to several excellent publications'"3 covering the principles and application of the gyroscope. The heart of the gyro-compass is the gyroscope, or rapidly spinning wheel, which rigidly maintains its angular orientation in inertial space. Free gyros employ universal joints to allow the wheel axle to maintain its rigid spatial orientation independent of base motion disturbances. Free gyros are independent of the earth's turning and are not north-seeking. Only as they might be initially oriented parallel to the earth's turning axis could any north indication be obtained. In practice, the free gyro tends to drift off its set position and lose its accuracy. The Sperry-Sun Well Surveying Co. instrument (5M in O. D.) is of this free gyro type. It is counterbalanced, however, against the rotational effects of the earth, so that orientation of the spinning axis will be maintained throughout the survey.

Jan 1, 1960

An unexpected demand having entirely exhausted the Institute's supply of the Bulletins for January and February, 1916, the sum of $0.50 each will be paid for. a limited number of copies of these Bulletins, which send to the Secretary of the Institute.

Jan 5, 1916

Oklahoma Geological Survey, Faculty Exchange, Norman, Okla The Oklahoma Geological Survey was closed for lack of funds July 1, 1931. However, a list of publications "will be sent and requests for publications will be filled in so far as possible Address the above.

Jan 1, 1933

By R. H. Lee

WITHOUT doubt, one of the most frequent and serious annoyances connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is ? tight," all available men are put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens-up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a.' cold," or at best a " high-sulphur," east is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot; the pressure rises; the amount of gas made' is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature " mentioned by Mr. .Johnson, and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke, high in sulphur, is used:

Jul 1, 1906

By C. K. Leith

The question as to what grades of ore it pays to conserve for the future, and the valuation of low-grade reserves, are becoming immediate and definite as applied to the individual ore deposits, and seems to call for some sort of quantitative answer.

Jan 1, 1915

Discussion of the paper of B. H. Dunshee, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 30, August, 1913, pp. 1511 to 1531. GEORGE E. MOULTHROP, Butte, Mont.:-The recording for the first time by Mr. Dunshee, in a readily usable form, of the various systems of square-set framing applied in the Butte district is a valuable contribution to mining information. The many different methods of framing employed, due to the individual ideas of superintendents and foremen of segregated companies, have given full opportunity to determine the best framing for the conditions as found in these mines, and the final adoption of a system uniform for all the mines has come about through a study of these various methods and an experience covering a period of many years. The sawed 10 by 10 in. and 12 by 12 in. timbers undoubtedly give the best satisfaction; and the style of framing the sawed timber that under all conditions has given the best practical results is that used in the Anaconda group and other mines, described and recommended by Mr. Dunshee. In this framing the posts have a horn 2 in. high and 6 in. square, the cap end having dimensions of 3 by 6 in. Instead of the framed girt shown in the drawings of the Anaconda group, the 6 by 10 in. girt adopted at some other mines, which fits into the cap and post framing with no other preparation than cutting the timber to the necessary length, fills all the necessary requirements for strength and affects a material saving in timber and labor. This, as Mr. Dunshee states, is without doubt the type of framing which would be adopted as a standard for 10 by 10 in. sawed timbers if sawed timber sets were to be used in the future generally. But saw-timber for the mines was becoming scarce and expensive, and round timber for the square sets furnished an alternative which provided, at greatly reduced cost, material which in every way supplied the requirements of the mining conditions. The use of the round timber with a satisfactory framing makes available a conveniently located and large source of supply which up to this time has served no useful industrial purpose. Particularly is this true of small timber, which is still standing in great quantities in the forests where the trees more desirable for commercial purposes have already been cut and marketed.

Jan 11, 1913

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of the continued interest in the dry beneficiation of gypsum and the development of higher capacity color sorting machines. The ore used was a discarded fraction that consisted of – 1 ¼ -in, to + 3/8 -in. ore containing 63.1 to 71.4% (average 67.7%) gypsum. This material was contaminated by various amounts of both carbonate rock and shale, but no pretreatment was performed other than screening to closer size limits before electronic color sorting.

Jan 4, 1969

By Max Barber

PRESENT equipment and practices in open-pit mines of the Lake Superior iron ranges have been described recently in some detail by A. H. Hubbell.1 It is anticipated that any further improvements will be the result of gradual evolution of present methods and equipment, just as those now used have been gradually evolved from earlier methods. An exception to the process of gradual evolution during the last decade has been the adoption of electric power for operating shovels and trains in open-pit mines, but it is not expected that any such revolutionary changes will be made in the future. The use of Diesel, engine equipment will gain considerable headway, no doubt, and will find favor in certain lines of operation as improvements and adaptations are evolved to meet particular requirements. The question of installing belt conveyors for handling material from deep mines of restricted area, where haulage grades become a serious consideration, or even for transferring earth, rock, or ore material for distances of several miles, is now being studied and some very interesting data are being obtained.

Jan 1, 1932

By Charles J. Potter

There are many sources of energy available for consumption. Some available are solar, tide and wind. However, in terms of relatively large usage, only four principal sources are used for primary energy today. They are coal, oil, natural gas and water power. Such additional items as wood and nuclear energy, although supplying quantities of energy today, do not in the aggregate amount to any real significant quantity, but nuclear energy must be considered for future use. In addition, such a thing as gas from distillation of coal and oil is not considered primary energy. The principal markets for primary energy are the electric power utilities, space heating, industrial uses and transportation. The electric utility use of energy is primarily from coal, followed by natural gas and water power. Space heating is primarily a gas market, followed by oil and then coal. Space heating by electricity is only considered in the generation of electric power. Transportation's principal source of energy is oil. Coal has practically no market left in this field.

Jan 4, 1962

The curve of Fig. 3 for pyrite requires modification. There 11% a range of pH values from 6.2 to 7.8 for which no cyanide is required to prevent contact. From 7.8 to 11.3 a small amount of cyanide is required, with a sharp maximum of 20 mg. per liter at pH=9.6. The mistake arose from considering too few solution compositions (17 were considered) in constructing the curve. Subsequent work with other collectors indicates that the corrected curve is typical for such systems; it illustrates the further development of the dip in the pyrite curve of Fig. 5.

Jan 1, 1938