Search Documents

By Walter H. Munk

Generation of Waves by storms, and the transformation of waves in shallow water by local bottom topography are briefly reviewed. A detailed description of water motion in waves explains the nature and distribution of wave forces. A numerical example dealing with forces and moments against vertical piles summarizes the principles involved. Introduction The oil industry is moving into the open waters of the Gulf of Mexico. The design and construction of offshore drilling rigs present a number of difficult problems, among them problems involving the action of waves on fixed and floating structures. This paper deals with our present knowledge of ocean waves as it pertains to these problems, and the principles involved in computing wave forces against fixed structures. It is hoped that the more difficult case pertaining to floating structures can be discussed at a later time. None of the engincering aspects of the problem are entered upon in this paper, yet an understanding of the principles presented here should be helpful in the solution of practical problems. Waves are capable of exerting almost unbelievable forces. During a gale, waves at the harbor entrance of Amsterdam Canal in Holland lifted a 20-ton concrete block, which was resting on the bottom in 12ft of water, and deposited it on top of a pier which was 5 ft above the high water mark. At Wick Breakwater in Scotland, a mass of large stones in cement and bound together with iron rods, weighing 1350 tons, was broken loose and moved bodily! But one need not go to Holland or Scotland to find evidence of damage that waves are capable of inflicting (Fig I and 2). What is the mechanism by which waves are capable of exerting such enormous forces? To answer this, we must consider briefly the nature of wave motion. When a wind blows over a wheat field, waves appear to travel across the field, whereas the wheat itself remains rooted, slowly swinging back and forth. Similarly, in the case of water waves, the waveform travels swiftly over the water surface, whereas the water particles oscillate back and forth, but scarcely advance. The speed of the wave form is called wave velocity, the speed of the water particles is called orbital velocity. This fundamental difference between wave velocity and orbital velocity was already recognized by Leonardo da Vinci. Orbital velocity is generally much slower than wave velocity except for a breaking wave, a case which is of particular importance in the application to engineering problems. Forces exerted by the waves on obstacles

Jan 1, 1949

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. Robert W. Hunt Medal and Prize THE partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Division, shall be appointed by the Iron and Steel Division annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of .the Institute. 5. The recipient of the award shall be designated "The Hunt Medalist." Awards of the medal have been made as follows: 1920—-Robert Woolston Hunt. 192G—John A. Mathews. 1926—Charles Lewis Kinney, Jr. 1929—Edgar Collins Bain. 193G—James Aston. Awards of the prize have been made as follows: 1928—C. H. Herty, Jr. 1929—William E. Griffiths.

Jan 1, 1930

By Andrew Allen

WHEN a mine is changed from hand, to me-chanical loading, the character of the coal dumped at the tipple is changed in many ways. Selective mining is not so easy with mechanical load-ers, and where much picking is done at the face it is apt to be wasteful anyway. Much recoverable coal is apt to be lost by too free gobbing and, in my opinion, picking at the face should be confined to removal of heavy rock, such as pieces of roof or bottom or sulfur balls. and to such clearly defined and persistent bands as can be readily recognized and segregated. With mechanical loaders of the shovel type, even this amount of gobbing is almost impossible. When coal is shoveled into a conveyor there should be no difficulty in doing as much picking as now by hand loading. The size of lumps may be greatly increased, on ac-count of the ease of handling them with a shovel, as the miners will not break them up in order to lift them into cars. Fines may be increased. This is, of course, not universally true, yet it is my opinion that a shovel breaks the coal more, as a rule, than hand loading. This might not be true with all types of shovels and is cer-tainly not true with a conveyor, either with or without the "duck-bill." The average car load will be greatly reduced in fields such as Illinois and Indiana, in which it is the practice to build up the coal above the sides. Where "level full" regulations prevail there should be no material change. When the coal comes to the tipple these differences usually result in the discovery, that many changes are necessary in the preparation plant. The increase in the percentage of fine sizes will probably not bother the screen, but may overload the conveying apparatus. The larger size lump may clog the chute, but as a rule the efficiency of the sizing screens is not greatly affected. In one completely mechanized mine the proportions of 6-in. lump and 2-in. screenings, when loading by hand, were 16.9 and 51.3 per cent respectively. When loading mechanically, these proportions changed to 15 per cent lump and 53.5 per cent screenings. The picking force on the tipple has been increased from 14 on hand loading to 33 men on mechanically-loaded coal. This is for an output of about 5000 tons.

Jan 4, 1927

By L. G. Truby

DISCUSSION By Rhrt G. Nisle, Phillips Petroleum Co., Barthesville, Okla. The subject paper presents the results of a reservoir behavior analyzer study of the pressure-production performance of five Ellenburger pools in West Texas. These five pools are Wheeler, TXL, Andector, Embar, and Martin. This laboratory has also made reservoir behavior analyzer studies in this area and arrived at substantially the same conclusions. Although the principal results of the studies made in this laboratory are confirmed by the results in the subject paper, there are certain points of difference. The points of difference are (1) the subject paper includes the Martin pool in the common aquifer, whereas our studies indicate that it is not, and (2) the subject paper concludes that the effective aquifer is considerably smaller than that derived from studies made in this laboratory. In terms of reservoir analyzer data, our rejection of Martin is based on the inability to obtain a satisfactory match of the pressure curve when Martin is considered as lying within the common aquifer. A satisfactory match was possible, however, when Martin was run as an isolated pool. This indicates that the pressure disturbance resulting from production at Martin had not reached Embar, Andector, TXL, or Wheeler at the time of our study. A similar situation exists relative to Dollarhide. In tern of geological data, our rejection of Martin is based on the presence of a faulted zone between Martin and Embar. This condition is indicated in Fig. 4 and again in Fig. 10 of the subject report. If a permeable connection between Martin and the other fields does exist, it is probably by way of a detour around this fault. The second point of difference between the two studies is illustrated by a comparison of Fig. 4 of the subject paper with Eg. A. Fig. A is obtained from an internal report on one of the studies made by this laboratory. It will be noted that the area indicated in Fig. 4 is roughly that marked "Pool Unit" in Fig. A. The additional portion of the aquifer shown in Fig. A was simulated on the reservoir analyzer by means of the water drive network. A satisfactory pressure match could not be obtained without this additional network. The differences involved here stem from a more fundamental consideration concerning reservoir analyzer operating techniques. The true source of these differences in reported results cannot at this time be determined because of the incompleteness of the subject paper. It is not stated, for instance, whether the pressure match was induced by altering the field resistance or the field capacitance, or both. Changing analyzer

Jan 1, 1953

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

Geostatistics originated as an application of a classical statistical concept, multivariate linear regression, to the solution of a practical problem, estimation of reserves in the South African gold mines. In this respect, geostatistics should only be considered as one statistical method among many that can be used to evaluate mineral deposits. R.F. Shurtz has studied possible applications of power spectrum analysis to the same problem, and these studies may result in future improvements over the presently accepted geostatistical methodology. The intention of R.F. Shurtz's paper, as stated by the author, is to "relate geostatistical doctrine to classical statistical and mathematical concepts." However, in this comparison the "geostatistical doctrine" appears to include only the simplest among the geostatistical concepts advocated by G. Matheron, while "classical statistical and mathematical concepts" are limited nearly exclusively to power spectrum analysis. The author attempts to compare the two methods, and to prove the theoretical superiority of power spectrum analysis. Unfortunately, a number of errors and incorrect statements are made concerning both the theory and application of geostatistics, which invalidate the comparison and the conclusions drawn from it. The errors made in this comparison are understandable since few scientists can claim to have expertise in two theories as diverse as those compared here. In many respects, this paper is reminiscent of polemics which occurred 15 to 20 years ago when geostatistics and trend surface analysis were compared. Each method has its own merit and limitations, and none can claim absolute superiority. The most misleading statements found in R.F. Shurtz's paper are: The definition of the semivariogram given on page 1923 is incorrect. If the maximum difference between two assays is 1, the maximum value of the semivariogram is not 1, as stated, but 0.5. The comparison of geostatistics and linear regression made in the section entitled "Insufficiency of Classical Statistics?" is not valid. The semivariogram of the sample values given in Table 1 (page 1919) has a parabolic shape indicative of a linear drift. When such a semivariogram is observed, the simplest method of geostatistical estimation (linear kriging with unknown mean) is not applicable. Universal kriging must be used that takes trends into account. On page 1921 it is stated that the use of trends "is officially disparaged in geostatistics." Again on page 1924 mention is made to "Matheron's commitment to random process (intrinsic) models and his present categorical rejection of deterministic (trend) models for mineral deposit evaluation." Indeed, from articles published by geostatisticians in the 1960s one could infer that geostatistical methods are not compatible with the presence of trends. However, even the simplest

Jan 1, 1984

By J. H. Frye, C. P. Sun

A PRIMARY substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver aneys.1-5 It has been shown that at least, four factors are involved: (I) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2.4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. CALCULATION OF RATES OF WORK- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By Richard H. Willey

EFFICIENT handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. BINGHAM CANYON MINE The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been metamorphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling and blasting of the porphyry apparently becomes easier as depth is attained, but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. PAST METHODS At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1947

By H. L. Riley, B. W. Gandrud

A froth flotation unit was added to the DeBardeleben Coal Corporation's Empire washer at Empire, Alabama, in the fall Of I94O following an investigation of possible ways and means of recovering coal values from settling-tank overflow or slurry. Officials of the DeBardeleben corporation hoped that some practical and reasonably economical way could be found for recovering fine coal from overflow water, although there had as yet been very little progress along this line in the Alabama coal fields. The Bureau of Mines was asked to cooperate in the project through its Southern Experiment Station, at University, Alabama. This paper presents a brief description of the process and the installation that resulted from the investigation of the overflow water or slurry problem at the Empire mine. The experimental data include' as a Part of this Paper were obtained during the course of the investigation in 1940 Since that time, however, the flotation unit has been running more or less continuously without significant operational changes and is still Performing pretty much in accordance with the data obtained in 1940. Flowsheet at Empire and Type of Coal Treated The Empire mine is developed on the Black Creek bed near the the border of the Warrior field. The coal in this bed is extremely low-ash and although there is an almost complete absence of bone coal and partings, the bed is so thin that, with mechanized mining, a high percentage of rock from roof and floor inevitably gets into the run-of-mine coal. The thickness of the Black Creek bed throughout the part of the Warrior field in which it is mined extensively is rarely over 30 in. and probably would average about 25 in, the coal is of the high-volatile A rank and of excellent quality, but as a result of admixture of roof and floor material, the run-of-mine product usually contains I ; to 20 pct rock by weight. he following is a proximate analysis on an "as-received " basis of a typical seam sample from the Empire mine:' moisture, 3.0 pet; volatile, 34.6 fixed carbon 58.3; ash, 4.1 This sample shelved 15,070 Btu per pound and 0.9 pct sulphur on a moisture-and-ash-free basis. In the Empire preparation plant the lump sizes above 3 in. are removed and hand-picked on a Marcus conveying Screen, the 3 to ? -in. size is removed by vibrating screens and washed in two Montgomery single-cell jigs, and the ?-in. to o slack is cleaned on four diagonal

Jan 1, 1949

By W. Rostoker

INTRODUCTION THE process of diffusion alloying of mixed powders offers attractive possibilities both commercially and experimentally. It avoids the fabrication difficulties arising from high alloy contents. Indeed, the process is facilitated by larger alloy additions. The direct formation of the part or test piece and the opportunity to perform machining operations under more favorable conditions are of no small importance. However, it is necessary to make only brief mention of the interesting features. As yet there have been few attempts to study this process in detail and to carry it to completion, if such is possible. It was intended not only to measure the intermediate and optimum magnetic properties of sintered alloys but to use magnetic testing itself as a means of following the progress of alloying under various conditions. Having established that alloys could be successfully synthesized by this technique, the opportunity was taken to study the magnetic properties of several alloys of iron and silicon which had hitherto been too difficult to prepare in suitable test piece form, While avoiding some of the difficulties inherent in the fabrication of alloys by orthodox methods, the diffusion alloying process introduces a few of its own. The first of these is the evaluation of the approach to homogenization. In recent years some notable contributions have been made to this question, but considerable uncertainty remains in its definition and evaluation. This work has concerned itself with further study of this problem and it is hoped that more light has been shed on it, The second of these difficulties arises from the presence of porosity. It is inevitable that in the consolidation of a loose bulk of powder, there should remain some voids unless extremely high pressures are repeatedly applied. It was therefore of importance to investigate their effect on magnetic properties. Recently this effect has been studied and certain predictions made of its behavior. It is believed that the experimental results presented here provide a sound substantiation of the theoretical treatment. The attempt has been made to synthesize five alloys of the iron-silicon system and three each of the iron-nickel and iron-cobalt systems. A series of experiments was also conducted on some of these alloys to test their susceptibility to heat treatment. Some unfortunate experiences have provided opportunity to report data on the deleterious effects of nitrogen on magnetic properties when present as a contaminant in protective atmospheres. MATERIALS, PREPARATION OF SAMPLES AND TESTING The purest materials available were employed for this work. A specially purified,

Jan 1, 1948

By John Chipman, Theodore B. Winkler

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By Theodore B. Winkler, John Chipman

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By W. Rostoker

The process of diffusion alloying of mixed powders offers attractive possibilities both commercially and experimentally. It avoids the fabrication difficulties arising from high alloy contents. Indeed, the process is facilitated by larger alloy additions. The direct formation of the part or test piece and the opportunlity to perform machining operations under more favorable conditions are of no small importance. However, it is necessary to make only brief mention of the interesting features. As yet there have been few attempts to study this process in detail and to carry it to completion, if such is possible. It was intended not only to measure the intermediate and optimum magnetic properties of sintered alloys but to use magnetic testing itself as a means of following the progress of alloying under various condi-tions. Having established that alloys could be successfully synthesized by this tech. nique, the opportunity was taken to study the magnetic properties of several alloys of iron and silicon which had hitherto been too difficult to prepare in suitable test piece form. While avoiding some of the difficulties inherent in the fabrication of alloys by orthodox methods, the diffusion alloying process introduces a few of its own. The first of these is the evaluation of the approach to homogenization. In recent years some notable contributions have been made to this question, but considerable uncertainty remains in its definition and evaluation. This work has concerned itself with further study of this problem and it is hoped that more light has been shed on it. The second of these difficulties arises from the presence of porosity. It is inevitable that in the consolidation of a loose bulk of powder, there should remain some voids unless extremely high pressures are repeatedly applied. It was therefore of importance to investigate their effect on magnetic properties. Recently this effect has been studied and certain predictions made of its behavior. It is believed that the experimental results presented here provide a sound substantiation of the theoretical treatment. The attempt has been made to synthesize five alloys of the iron-silicon system and three each of the iron-nickel and iron-cobalt systems. A series of experiments was also conducted on some of these alloys to test their susceptibility to heat treatment. Some unfortunate experiences have provided opportunity to report data on the deleterious effects of nitrogen on magnetic properties when present as a a in protective atmospheres. MateRIALS, PREPARATION OF SAMPLES and Testing The purest materials available were em. ployed for this work. A specially purified,

Jan 1, 1949

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902

By F. W. Hillnhutter

In plant tests with a 9.7 m hearth diameter high top pressure blast furnace the influence of disintegration of sinter during low-temperature reduction on blast furnace performance was evaluated. The blast furnace burden during the test period consisted of 74% self-fluxing sinter with a basicity of CaO/Si02 = 1.3, 15% pellets, 6% lump ore, and 5% recirculated slags. The sinter for the test was produced in a modern sinter plant. By changing the fuel rate and/or the MgO content at a constant basicity CaO/Si02 sinters with different low-temperature disintegration properties could be produced. The blast furnace was equipped with pressure monitoring devices at medium height of the furnace stack wall. This device provided in addition to the normal operating data readings of pressure losses in the upper and lower part of the furnace. The basic physico-chemical factors determining low-temperature disintegration are explained. The testing devices and the extent of quality control measures of sinter during the test period are outlined. Conclusions are drawn from the plant test in relation to sinter properties.

Jan 1, 1977

By C. A. Stetefeldt

The hacienda Sauceda is one of the largest and finest haciendas in the vicinity of the City of Zacatecas, Mexico, and is said to reduce ores by the Patio process more cheaply than any other establishment. It receives its supply of ore from the San Acacio mine. This mine has been for some time, like most of the Zacatecas mines, out of bonanza, and yields, at present, ore of rather low grade. The silver occurs principally as silver-glance, ruby-silver and native silver, associated with pyrites of iron and copper, and some galena and zinc-blende, in a gangue of pure quartz, which takes the form of amythyst whenever the ore is of high grade. All the ore, as it comes from the mine, is broken by hand into small pieces, and sorted before it is delivered to the hacienda. Here it is first crushed dry in Chili mills, and then ground wet in arrastras to an impalpable powder. The sulphurets not decomposed in the patio process are separated in the settlers from the tailings and concentrated by hand. By roasting them in a reverberatory furnace with carbonate copperores, "magistral" is obtained. All machinery is driven by mulepower.

Jan 1, 1885

By F. Valton

In the number of the Engineering and Mining Journal for April 7th, 1877, Mr. W. P. Ward, of Cartersville, Georgia, explains in a very interesting manner, the results he obtained in the manufacture of ferromanganese in the blast furnace. These results may be summed up as follows : Production in the blast furnace of an alloy containing 67.2 per cent. manganese and 3 per cent. of carbon at most, with a utilization of the manganese amounting to 58 per cent. With the exception of the indicated proportion of' carbon, which should be almost doubled to express the true state of facts, we would have had no observations to make on Mr. Ward's paper had he taken into account the results obtained in the same line in other centres of production. Before 1870, spiegel with 8 or 10 per cent. manganese only was known among blast-furnace products. In a journey to Sweden, in 1871,I ascertained that the Schysshyttan works manufactured regolarly a spiegel with 18 per cent. manganese. Later, at the Vienna Exhibition, in 1873, the Sava and Jauerburg works, in Carniola, presented to the jury a ferromanganese, obtained in the blast fur-

Jan 1, 1879