Search Documents

By Che, C. W. Spencer, C. A. Steidel, Yu Li

Grain boundary grooving as it occurs in a 5.5-deg simple-tilt nickel bicrystal immersed in a saturated Ni-S liquid has been studied. A 1/3 (t= time) dependence for the depth of the groove indicates that the rate -controlling meckanism for groove developvnent is volume diffusion in the liquid. The activation energy for the diffusive process is estimated at 15 kcal per mole. Using an extended form of W. W. Mullins&apos; analysis for grooving reactions, a computer is employed to fit the appropriate diffusion equation by a numerical method. From the analysis a possible method of measuring L.S. the solid-liquid interfacial tension is demonstrated. WHEN a polycrystalline solid is heated in equilibrium with a saturated fluid phase, grooves will form at the intersections of the grain boundaries and surface. The equilibrium root angle of these grooves is determined by the balance between the grain boundary and solid-fluid interfacial tensions. The grooves deepen and widen with time due to a difference in chemical potential between the flat interface and the curved interface of the groove. In this investigation solid-liquid interaction at a grain boundary is studied, with the object to determine the mechanism of grain boundary grooving in the presence of a saturated liquid. Extension of Mullin analysis then permits the estimation of the solid-liquid interfacial tension. Herring has demonstrated by dimensional analysis that the quasi-steady state change of the dimensions of a small particle during sintering is proportional flow, evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, respectively, if geometric similarity of consecutive configurations of the particles holds. Mullins has extended this analysis to grain boundary grooving. In the case of shallow grooves he solves the diffusion equations for evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, and obtains the same time dependence for any linear dimension of a groove as Herring found for the change in dimension of small particles. In Mullins&apos; analysis2&apos;3 grain boundary grooving of a bicrystal by volume diffusion in the presence of a saturated fluid phase was considered. Several assumptions were made prior to the analysis: 1) the solid-fluid interfacial tension is independent of crystallographic orientation; 2) the Gibbs-Thompson equation relating curvature and chemical potential is applicable at the solid-fluid interface; 3) the relaxation time of the diffusion field is small compared with the time for appreciable changes in the curvature of the groove, so that the diffusion is divergence-less; and 4) the groove has a small slope relative to the initial flat interface. Usually this last condition is fulfilled only for solid-gas systems. The solution of the diffusion equation under the above conditions produces a t1/3 dependence for any linear dimension of the groove in the case where volume diffusion is rate-controlling. The t1/3 dependence is valid because geometric similarity of the grooves exists for all time. EXPERIMENT In the experiment a 5.5-deg nickel bicrystal of <100> simple-tilt orientation was used.4 Grooving was studied in the presence of a saturated Ni-S liquid alloy as a function of time at 750°, 800°, 850°, and 900°C. A low-angle bicrystal was chosen for study to insure that 2L.S. > .b., where l.s.

Jan 1, 1964

By Benjamin Gildersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than Vi in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000. THE building stone of the Crab Orchard District is a fine-grained, thin-bedded sandstone which is so strongly cemented by silica that it may be classed as quartzite. As used in this paper the term building stone includes dimension stone, rubble, ashlar, flagstone, and rough broken stone. The Crab Orchard District is in the central portion of Cumberland County, Tenn. It is named from the town of Crab Orchard near which the stone was quarried first for industrial use. The heart of the district is an area of some 1200 acres from 1 to 3 miles east of Crossville which is 70 miles west of . Knoxville and 125 miles east of Nashville (fig. 1). At the present time, there are about 15 quarries worked by companies and individuals. Geology: The Crab Orchard District is on the Cumberland Plateau, or Cumberland Mountain as it is called frequently. Most of the area is characterized by a comparatively even surface from 1800 to 2000 ft in elevation and is drained by streams flowing into the Tennessee River. Included in the district are two quarries located 7 miles west of Cross-ville and this area is drained by tributaries of the Cumberland River. Most of the quarries are located near the 1800-ft contour which is just below the general upland surface. The surface rock over most of the district is the Rockcastle sandstone which has a thickness of about 260 ft.1 It is the topmost of the six formations of

Jan 1, 1951

By Benjamin Gildersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than Vi in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000. THE building stone of the Crab Orchard District is a fine-grained, thin-bedded sandstone which is so strongly cemented by silica that it may be classed as quartzite. As used in this paper the term building stone includes dimension stone, rubble, ashlar, flagstone, and rough broken stone. The Crab Orchard District is in the central portion of Cumberland County, Tenn. It is named from the town of Crab Orchard near which the stone was quarried first for industrial use. The heart of the district is an area of some 1200 acres from 1 to 3 miles east of Crossville which is 70 miles west of . Knoxville and 125 miles east of Nashville (fig. 1). At the present time, there are about 15 quarries worked by companies and individuals. Geology: The Crab Orchard District is on the Cumberland Plateau, or Cumberland Mountain as it is called frequently. Most of the area is characterized by a comparatively even surface from 1800 to 2000 ft in elevation and is drained by streams flowing into the Tennessee River. Included in the district are two quarries located 7 miles west of Cross-ville and this area is drained by tributaries of the Cumberland River. Most of the quarries are located near the 1800-ft contour which is just below the general upland surface. The surface rock over most of the district is the Rockcastle sandstone which has a thickness of about 260 ft.1 It is the topmost of the six formations of

Jan 1, 1951

By A. W. Hann

THE importance, to geologists and metallurgists, of knowing the mineralogical forms in which the silver occurs in ores has increased during the past few years, and will continue to increase as long as working hypotheses are converted into proved theories and rule of thumb methods are supplanted by scientific data. The methods used for the determination of these silver minerals have been: (1) careful study of polished ore sections with the microscope, and more recently, (2) metallurgical separation of the ground ore by flotation, tabling and panning, supplemented by microscopic examination of these separated minerals, and chemical analyses. During the course of some experimental work carried on by the testing department of the International Smelting Co. and myself, it became important to determine, in a general way, the distribution of the silver values in the minerals, as they exist in Tintic Standard and North Lilly siliceous oxidized lead-silver ores. These mines are in the East Tintic Mining District, State of Utah. In this work the second method was used. Differential flotation tests were run, separating the sulfide from the oxidized minerals, and the products were assayed. Various concentrates were carefully panned and the separated products assayed; special samples of ore were selected and assayed. The microscope was used only for the purpose of determin; ing whether the individual minerals were in the so-called "free" state. Analysis of Tintic Ores These chemical and mineralogical determinations showed the silver to be present as native silver, argento jarosite, argentite, and combined or inherent in the tetrahedrite, chalcopyrite, galena, pyrite, cerussite, anglesite, mimetite, malachite, iron oxide and occluded in the quartz. Careful microscopic work would probably show other forms in small amounts, such as the halide silver minerals and some of the antimony sulfide combinations. The tabulation of the analyses of the various products (Table 1) shows no evidences of fixed ratios of silver to any particular base metal.

Jan 1, 1929

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922

By Advisory Editorial Board

FOR many years there has been no book that adequately represented the present state of the art of coal preparation-an art that has been rapidly changing during the passing years, and particularly during the last ten or fifteen years. In fact, changes of preparation have been so rapid that no book could keep abreast of their progress, and even the Proceedings of the technical societies have not been able to do so. It has been the intention of this committee and of the editor to make this book as nearly up to date as possible and to make it one that would appeal primarily to operating men, while at the same time adequately showing the theory back of the many processes used. The start of the war and the increased calls upon the time of the authors selected for the various chapters have slightly dimmed the brightness of the ideal intended, but the result undoubtedly brings the practice of preparation and its literature closer together than they ever have been before. It is the hope of the committee that this book will be useful both to those whose daily work is concerned with preparation and to consumers who use the product produced at the many fine and up-to-date coal plants throughout the country, which are now producing, as they always have done, all the coal needed by this country in its greatest crisis. While the committee has exercised a general supervision over the preparation of the various chapters, all of the correspondence and edi¬torial work have been done by Prof. David R. Mitchell, and it has been his untiring interest and devotion that have made the book possible-the credit is all his. Advisory Editorial Board, B. M. Bird Cadwallader Evans, Jr. Thomas Fraser W. H. Lesser William C. Mcciilloch J. B. Morrow H. S. Salmon Raymond E. Salvati Kenneth A. Spencer H. F. Yancey Howard N. Eavenson, Chairman.

Jan 1, 1943

By Sir John Cadnan

The production from the Maidan-i-Naftun area for the year ending March, 1928, was 5,340,000 tons (40,210,200 bbl.), an increase of nearly 13 per cent. over the production for the year ending in March, 1927. The production by years since the opening of the field in 1912 is given in the following table: [1 ton = 7.53 bbl.] Year Ended MaRch Tons Year Ended March Tons 1912 (7 months)............. 43,084 1920....................... 1,354,631 1913........................ 80,800 1921....................... 1,767,070 1914........................ 273,635 1922....................... 2,310,098 1915........................ 375,977 1923....................... 2,913,908 1916........................ 449,394 1924....................... 3,583,000 1917........................ 644,074 1925....................... 4,221,000 1918........................ 897,402 1926....................... 4,470,000 1919....................... 1,081,919 1927....................... 4,735,000 1928....................... 5,340,000 The actual production represents only a small proportion of the potential production. The Masjid-i-Suleiman Field The present producing unit, the Masjid-I-Suleiman, is an anticline some 20 miles in length by 4 miles in width, including three domes as so far proved. The producing horizon is a very open, dolomitic limestone, which, while showing much variation in texture and porosity, is so connected that the lowering of pressure in one section of the field quickly affects the whole area. The topography of the field is broken, with differences of well elevations of as much as 1100 ft. The depths to the limestone vary from about 800 to about 5000 ft. The closed-in pressure of the oil wells varies from zero to 50 lb. per sq. in. and that of the gas wells is about 450 Ib. Although the static oil level may be several hundred feet below ground level, in oil wells of high elevation, all the wells flow continuously or intermittently after they are once started—the majority continuously. The gas is very high in hydrogen sulfide in gas-oil wells of low pressure.

Jan 1, 1929

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,&apos; or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9&apos; per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By J. J. Strohl, H. J. Schwellenbach

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.&apos; By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

By H. J. Schwellenbach, J. J. Strohl

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.&apos; By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,&apos; or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9&apos; per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By C. M. Means

CONSIDERING the hazard involved in mining operations, statistics show, that a very small percentage of accidents is chargeable to electricity. These accidents do represent quite a large percentage of those that are preventable and they are the direct result of the introduction, for purely economical reasons, of a dangerous element. The introduction of electricity in mines should decrease the hazard, and in no case should electricity be applied to the mechanical operation of equipment if by so doing the dangers incidental to mining are increased. The greater number of accidents are the result of persons coming in contact with exposed conductors at potentials varying from 250 to 500 volts direct current. The use of alternating current at higher potentials than these is quite common in large mines, but it is very rare that an accident happens from this source. This is explained by the fact that where these high voltages are warranted, proper precautions are taken, and the installations are directed by those who fully appreciate the dangers incidental to the work. Direct current is in much more general use than alternating current because of its adaptability to haulage locomotives and the low cost of installation in small operations. We are, however, coming to a more extended application of alternating current for the operation of mechanical devices used in connection with mining. Our underground direct-current wiring system is an evolution from the surface trolley and feeder systems. This is probably due to the fact that our earlier successful applications were electric locomotives, which required the use of a trolley wire. The trolley current has been almost banished from industrial establishments on the surface because of the hazard involved, yet we use it indiscriminately underground, where the dangers from accidental contact or fire are infinitely greater. This does not mean that the underground trolley systems should be eliminated, but it does imply the proper safeguarding of such equipment as is necessarily a part of the trolley systems.

Jan 4, 1914

By Albert Walcott

THE success of various operations in the manufacture of optical glass depends, in a large measure, on the ability to maintain proper heat control. A good pyrometer system is, therefore, a very necessary part of the equipment needed. Men of long experience in dealing with high temperatures, who have acquired through constant practice the ability of judging approximate temperatures by means of color, are undoubtedly valuable, but even the most competent are not as reliable as a good pyrometer system. They admit that their ability to judge accurately varies from day to day and that their judgment is affected considerably by the condition of the sky, whether it is clear or cloudy. Besides, where it is a matter of only a few weeks to train a man to operate a pyrometer system, it takes about as many years to train him to judge temperatures by the state of incandescence. The pyrometer outfit in use in the glass plant of the Bausch & Lomb Optical Co. consists of the following: Platinum elements, optical pyrometers; base-metal elements, indicators, potentiometers, and recording pyrometers. Platinum Elements and Optical Pyrometers.-Temperature control in - the melting operation is of such great importance that it is very desirable to know the exact temperatures, relative temperatures being of little value. The use of the platinum element is to determine the rate of heating or cooling of the furnace. The platinum couple is installed in either the crown or the wall of the furnace. It is placed first in a porcelain protecting tube and this is placed in a permanently fixed fireclay tube projecting from 1 1/2 to 2 in. into the fire-chamber. It has been found impractical to use the platinum couple for determining exact temperatures of the melting furnace, for the platinum element deteriorates rather rapidly at the high temperatures used, 2500° to 2700° F. (1371° to 1482° C.). When protected and installed as described, though,

Jan 9, 1919

By M. B. Bever, A. K. Jena

In the investigation reported here, calorimetric measurements have been made to determine the heat of formation of the compound AuSb2 and the partial gram-atomic enthalpies of antimony and gold in dilute solution in liquid tin and their enthalpy interaction coefficients. In order to interpret the behavior of antimony and gold in dilute solution in tin, nonzero values are assigned to the energies of bonds between like solute atoms relative to the pure solute state. Sa.mples of the compound AuSb2 were prepared by melting stoichiometric amounts of antimony and gold (99.999 pct pure) in evacuated and sealed Vycor tubes, which were shaken vigorously and quenched in water. The ingots were annealed in evacuated and sealed tubes at approximately 700°K for 2 weeks. Metallo-graphic and X-ray examinations gave no indication of second phases or microsegregation. The samples were added from 273°K to tin-rich solutions in a solution calorimeter1 maintained at 623°K. The calorimeter was calibrated with tin; the heat content of tin, H623°K- H273°K, was taken as 4.08 kcal per g-atom.2 In each calorimetric run at least four additions were made. The total concentration of solutes in the bath at the end of any run did not exceed 1 at. pct. The measured heat effect of an addition was plotted against the average of the atom fractions x of Sb + Au in solution before and after that addition. From this plot the heat effect at infinite dilution h,,, and the composition dependence of the heat effect dh/dx in the composition range 0 < x < 0.01 were obtained. The results for the additions of antimony, mixtures of antimony and gold, and the compound AuSb2 are listed in Table I. The heat effect h on addition of a sample of the compound AuSb2 or a mechanical mixture of antimony and gold at 273°K to a tin-rich solution at 623°K can be expressed as:

Jan 1, 1969

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder&apos; led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

By Charles Willis

THE problem of the curtailment of forces in large numbers does not often come to employment departments and is, therefore, a problem that many departments are not prepared to handle intelligently. Those companies that are able to measure the individual efficiency of each man would probably lay off men according to their individual ability, irrespective of dependents, citizenship, or other considerations. During the war when labor was scarce, the business of the employment manager in industry was hiring men and carefully placing them where they were best fitted to work. The careful selection of employees had developed to a considerable extent before the war, and was becoming a recognized science. In the last few months, however, the cancellation of copper contracts, the accumulation of large stocks, the necessary curtailment of production because the copper could not be sold, and lack of any immediate prospects of the copper market opening, have led to a universal reduction of forces; and the problem that industry now confronts is that of discharging rather than employing. The problem has been aggravated by the cancelation of contracts in many war industries with the consequent turning loose of hundreds of thousands of men, a great amount of unemployment, and the return of the soldiers and sailors. The problem has now become one of reduction of working force with the least hardship and the least injustice, and yet caring for the returning soldiers, sailors, and marines who have been in the service of the government for nearly 2 years, and who have offered the supreme sacrifice. The Copper Queen Branch of the Phelps Dodge Corpn., operating at Bisbee, Ariz., found it necessary, along with all of the-other copper companies of the country, to reduce its force materially. In making this reduction it was, after due consideration, decided to classify employees with respect to dependents, length of service, and citizenship. The question of individual efficiency or workmanship was not considered. Copper

Jan 9, 1919

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers&apos; specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

BURKE BAKER, Philadelphia, Pa. (written discussion*).-The small briquetting plant of the American Briquet Co., at 25th Street and Washington Ave., Philadelphia, was built primarily as a demonstration plant. Its output per hour is 4 tons of 2-oz. briquets, which have been retailed in the, vicinity during the year the plant has been in operation. They have proved very acceptable for use in ranges, heaters and grates in-home, and in steam heating plants in apartment houses and hotels. They have not been sold for power purposes, although satisfactory tests have been made in. this field. Anthracite silt is used and is shipped direct from breaker or washery, the only preparation it receives being the removal f excess moisture by means of a Ruggles-Coles rotary dryer. Care is taken, however, to purchase silt containing less than 18 per cent. ash. The method is covered by U. S. Patent No. 941454, issued to Chas. E. Hite, and is known as the "emulsion process." The binder, which is the, basis of the patent, is composed. of 0.5 per cent. cornstarch or wheat flour; 1 per cent. asphaltum or hydrolene, and 6.5 per cent. water, on the weight of coal dust. It is prepared in a tank equipped with paddle agitators and heated by steam jets. The starch and water are first made into a paste by being brought to the boiling point with live steam; the melted asphaltum is then introduced and thoroughly beaten into the paste by the agitators. This rapid stirring breaks. the hot asphaltum into minute particles which are distributed through the paste, producing a smooth chemical emulsion. This emulsion, when dried, is not soluble in water. The binder is mixed with the dry coal dust in a horizontal paddle mixer, 8 per cent. binder to the weight of coal being used. The resultant plastic mass is then discharged into the press, which is of the simple roll type. Since the binder is a liquid and is not sticky or gummy until

Jan 3, 1918

By Ernest Darby

WHEN bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag may be incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal. When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not mixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week&apos;s run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below.

Jan 1, 1928