Search Documents

By W. D. Donnelly, M. L. Rudee

THE crystallography and morphology of ?-Al3Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 µ. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly Al13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (001)? 1 (110)Al [100]?|| H [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By I. E. Puddington

The property of surface tension in liquids is said to have been known to Leonardo de Vinci in about 1500. Approximately'300 years later Thomas Young and others provided the ground rules relating surface tension to the wetting of solids and to the pressure drop across curved surfaces. In retrospect it seems remarkable that more than 100 additonal years were required for substantial technological use to be made of the-information. Thus super critical and freeze drying to avoid shrinkage of finely divided solids have only seen industrial use since the 1930's and doubtless additional possible applications will be equally slow in finding concurrence of conditions to make them attractive economically. The use of a second liquid phase that preferentially wets ,a suspended solid as a flocculant for that solid was pointed out in 1943 (1). Combining this phenomenon with mechanical energy to alter the morphology of the flocs or with surface chemistry to utilize it in the selective flocculation in mixed solids required more than an additional decade. A major stimulant in advancing surface energy based technology 'of suspensions was the report by D. I. Stock in 1952 (2) that mechanical agitation of a dry suspension of barium sulphate in benzene produced dense microspheres of the solid with highly desirable sedimentation characteristics. Investigation of this observation revealed that it resulted from small quantities of water in the system and mechanistically the phenomenon was identical with that reported in 1943.withthe addition of mechanical packing (3). Here then was a base from which to separate more efficiently suspended solids, to make small spheres from powders, to separate selected components from mixtures of finely divided solids or to break emulsions. Each of these possible branches of technology has been slow in developing on other than an experimental scale although considerable

Jan 1, 1979

W. A. SCHLESINGER,* Denver, Colo.-Two problems are of great interest to the radium manufacturer at the present tine: The first is to perfect a process, more efficient and more economical, which is capable of treating a greater variety of ores. . Practically all the radium now manufactured in the United States is extracted from carnotite ores and these vary a great deal according to their location. The amount of sulfates contained in the ore is of particular importance, and any straight acid-leaching method, such as developed by the Bureau of Mines, becomes prohibitive when the ore contains more than 0.5 per cent. of sulfates, as the sulfates go into solution and naturally precipitate the radium as insoluble radium sulfate. Since the amount of ore obtained from any one claim is usually comparatively small, it is necessary to work a number of claims in different localities, and a process, in order to be commercially satisfactory, should handle all of these ores. In other words, it would be entirely unprofitable for radium manufacturers to employ any process which cannot treat any but sulfate-free ores. He must deal with carnotite containing appreciable amounts of sulfates, and must be able to work this in with the other ores. Carbonaceous ores from certain sections in Utah; which are known to contain as pinch as 1.0 per cent. and more of volatile matters, are prone to a, nitric acid-leaching process. The second problem relates to the treatment of concentrates. There is no doubt that a very large amount of low-grade ore, containing less than 0.75 per cent. uranium oxide, is available. It has been demonstrated that these ores can be concentrated, but there is still room for research

Jan 11, 1918

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

By William B. Heroy

During 1932 no important changes occurred in the position of Africa as a producer of petroleum. The progress of development and production in each of the areas of interest is described below. Egypt The producing fields of Egypt are Hurghada and Gemsa, located on the west short of the Red Sea, and Abu Durba in the Sinai Peninsula. Most of the production is obtained from the Hurghada field, chiefly from beds of Cretaceous age. To the end of 1930 the Hurghada field had produced 2,831,751 tons of petroleum. The Gemsa field, discovered in 1909, reached its peak of production in 1914, when 88,000 tons were produced. Of late years the production has greatly declined. Total production of the field to the end of 1930 is 182,870 tons. The total production of Abu Durba to the end of 1930 is 7069 tons. The production of Egypt for recent years is as follows: 1928, 269,324 tons; 1929, 271,520; 1930, 281,997 (1,996,000 bbl.); 1931, 288,260 (2,038,000 bbl.); 1932, 253,182 (approximately 1,790,000 bbl.). Mozambique The operations of Inyaminga Petroleum Ltd., which was engaged in drilling in the colony, have been suspended. Angola Drilling operations in this colony, conducted by Companhia de Petroleo de Angola under a concession from the Portuguese Government, were continued. A test well drilled at Cacoba, about 60 miles southeast of Luanda, to a depth of 5651 ft. was not a commercial producer. A second well was being drilled in the vicinity at the end of 1932. Morocco Until last year the search for petroleum in Morocco was in the hands of several private companies but during 1932 the National Office of Liquid Fuels of the French Government took an active interest in the develop-

Jan 1, 1933

By B. M. Loring, I. R. Kramer, F. M. Walters

No observations on the mechanical properties of iron-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,1 or whether the lack of ductility observed was due to impurities in the alloys that he studied. EXPERIMENTAL METHODS The alloys were melted in a 100-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb. ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon [ ] was added as ferrosilicon. The alloys forged without difficulty-and were given a 90 percent reduction to 3/4-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for [ ] 24 hr. at 1150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for z hr. at 540°C. (1000°F.) and air-cooled. The tensile specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were V-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1941

By E. F. Northrup

THESE brief notes respecting the properties of pure tin that make it useful as a pyrometric substance summarize information gathered by the writer In an extensive experimental investigation on the electrical properties of metals in the molten state. Tin in quantities sufficient for pyrometric purposes may be obtained at relatively low cost and in a state of high purity. The metal melts at 232° C. and, according to determinations made by Greenwood,. 1909, does not begin to boil until a temperature of 2270° C. is reached. The writer can assert, from personal observations carefully made, that tin shows no tendency to boil at a temperature of 1680° C. If Greenwood's observations are correct the temperature interval, 2038° C., in which tin exists as a liquid under atmospheric pressure, exceeds that of any other substance. It has never been observed, as far as the writer is aware, that tin forms any chemical union, as carbide, with carbon at the highest temperatures at which it can exist as a liquid. It is quite certain from the writer's personal observation that tin heated in Acheson graphite to 1680° C. remains chemically uncontaminated. Wires of pure tungsten do not dissolve in molten tin at temperatures at least as high as 1680° C. Tungsten wires or rods may, therefore, be used as electrodes dipping into molten tin when required for measuring the resistance of the molten metal at very high temperatures. When tin is raised to a high temperature in a covered graphite container, the CO atmosphere that exists above its surface has a reducing action, which maintains this surface of mirror brightness. Incidentally, tin maintained molten in a crucible of Acheson graphite makes a most excellent bath into which may be inserted several pyrometers that are to be intercompared at the same temperature.

Jan 8, 1919

By Niels Hansen

Dispersion-strengthened aluminum products consist of an aluminum matrix containing finely distributed ceramic or intermetallic particles. Examples of the two types of product are SAP, in which the dispersed phase is aluminum oxide, and materials made from atomized aluminum alloy powder, in which the dispersed phase can be FeA1, particles.' A fundamental difference between the two types of product is that the elongation of aluminum/aluminum oxide products decreases with increasing temperature, whereas the elongation of aluminum- FeA13 products, like that of aluminum alloys, increases with increasing temperature. As regards the structural stability, aluminum/aluminum oxide products are stable to temperatures above 600° C as aluminum oxide does not react with aluminum, whereas prolonged heating at above 400°C of aluminum-FeA1, products leads to coarsening of the intermetallic phase and loss of strength.' On the basis of these results it is supposed that a dispersion-strengthened product combining strength, ductility, and stability at elevated temperatures may be obtained if the dispersed phase reacts with the matrix in such a way that the reaction does not proceed at any significant rate at the application temperature. Different ceramic or intermetallic compounds may be selected as the dispersed phase, and, as alloying of the matrix phase may also influence the reaction, many possibilities exist for each metal. In the present study, aluminum products containing different oxides have been examined. For a reaction to take place between the dispersed oxide and the aluminum the free energy of formation of the oxide (MeO) must be greater than that of aluminum oxide; the difference should, however, not be too great in order to limit the reaction rate. Furthermore the aluminum alloy formed when aluminum reacts with the dispersed oxide should have a melting point near

Jan 1, 1969

By T. S. Lundy, C. J. McHargue

HE diffusion rate of v48 in single crystals of bee vanadium has been determined at temperatures from 1002° to 1888°C. Standard techniques of lathe sectioning were used for specimens annealed above 1500°C while sectioning by grinding was used for specimens annealed at lower temperatures. As will be seen, the lower-temperature data is enhanced on an Arrhenius-type plot relative to values expected by extrapolation of the high-temperature data. Single crystals were obtained from Linde Co. In Table I the analysis supplied by the vendor is compared with an analysis at Oak Ridge National Laboratory of a sample after a diffusion anneal. The isotope v4' was prepared by the Isotopes Division of Oak Ridge National Laboratory. Proton bombardment of a titanium target in the 86-Inch ORNL Cyclotron was followed by a carrier-free chemical separation. Nineteen specimens, 1/2 in. diam and 3/8 in. long, were cut from the as-received vanadium single crystals. Each specimen was machined with the flat face perpendicular to the longitudinal axis. Specimens were polished through 1/0 emery paper and were etched with 25 pct HF-10 pct H2SO4-10 pct HNO3-55 pct H2O. The polishing and etching steps were repeated until a satisfactory surface finish was achieved. The isotope was electroplated onto the specimens from a neutral solution. Counting rates of the deposited layers were approximately 100 counts per sec. At temperatures above 1200°C specimens were annealed in a tantalum resistance furnace under an argon atmosphere. Temperatures were measured with a Pyro micro-optical pyrometer and a Pt-Pt 10 pct Rh thermocouple. At lower temperatures the specimens were sealed in evacuated quartz ampoules and annealed in Kanthal wire-wound horizontal tube furnaces. A severe reaction occurred at 1200°C between the quartz and the vanadium. This

Jan 1, 1965

By Arturo M. Morales

INTRODUCTION Manganese carbonates are nodulized by Cia. Mineral Autlan, located in Ongongo in the state of Hidalgo in Mexico. This kiln is fed minus 15 mm material at the rate of 1870 tpd. About 920 tpd is nodulized into a commercial product having a size range of 15 mm to 12 mm. The kiln also produces about 320 tpd of minus 12 mm fines and 40 tpd of chimney dust. Currently, the minus 12 mm fines are being recirculated to the kiln and the chimney dust is not being utilized. It has been found that there exists a market for manganese to be used as feed to the ferromanganese and silicomanganese furnaces. However, a coarse, lumpy feed can only be used in these furnaces. Accordingly, it has been proposed to screen the fines at 6 mm and agglomerate the minus 6 mm fraction along with the chimney dust and suitable binders. This paper presents the results of a feasibility study and test work aimed at producing an acceptable agglomerated product from the kiln fines for use in the ferromanganese and silicomanganese furnaces. Since the agglomerated product will have to be handled and loaded into trucks in the kiln area and transported over long distances, a minimum strength of 200 N is expected to be necessary. They should also have enough initial strength to be stockpiled and result in a minimum of breakage. A third important requirement is that the agglomerates should be resistant to disintegration during combustion. The recirculating fines were to be agglomerated in their original state, if possible, that is, without grinding. This eliminated the possibility of pelletizing as an agglomeration method. Based on a few laboratory trials, the briquetting method seemed most attractive, and a test program was initiated to explore the briquetting process.

Jan 1, 1977

By Thomas Watson

Introduction THE occurrence of zircon in pegmatites of acidic composition is recorded by many observers both in this country and abroad, and they form one of the most important geologic modes of occurrence of the mineral.' As is well known, commercially the most important American locality for zircon is near Zirconia in Henderson County, North Carolina, where many tons of the mineral have been obtained from a kaolinized pegmatite dike 100 ft. wide and traced for 1 ½ miles along the direction of strike N. 50° E. Zircon may be developed in pegmatites as inclusions in the principal rock-forming minerals, chiefly quartz and feldspar, and as a separate megascopic constituent in the form of grains and crystals not exceeding, as a rule, 2 in. in size, and usually smaller. In the Henderson County, North Carolina, pegmatite, zircon occurs in prismatic crystals with pyramidal terminations measuring up to 30 mm. in diameter, associated chiefly with the feldspar. In some of the apatite veins of Canada, which are closely allied to pegmatite dikes, zircon is reported in crystals upward of 6 in. in length and 2 in. 'and more in thickness. Zircon in large masses occurs in Virginia in the well-known pegmatites near Amelia in Amelia County, and near Gouldin in Hanover County. Both localities are in the middle eastern portion of the Piedmont Plateau province, and are separated by a distance of about 40 miles in a northeast-southwest direction. The rocks of both areas, including the pegmatite bodies, are in an advanced stage of decay, and, the hard and moderately fresh rocks are concealed beneath a cover of variable thickness of rock decay derived by the normal processes of weathering. Exposures, there-

Jan 7, 1916

By Horace Pops

ThE shape of the primary solid-solubility limits in copper-rich Cu-Si-Zn alloys has been discussed recently1 in terms of the atomic size effects and the electron concentration, e/a. Although these limits are parallel to lines of constant e/a near the Cu-Zn binary system, they deviate and become sharply restricted near the Cu-Si binary system. Hence, it appears that the primary solid solutions with higher silicon contents are restricted by the presence of the intermediate phases, [, X, and p, which follow them in the ternary system. owever, a similar restriction in solid solubility might also result from an interaction in the copper matrix between silicon and zinc. Evidence for such possible interactions has been observed, for example, in the Al-Mg-Si systion.A where a contraction of lattice spacings in the ternary solid solution appears to correspond to an electrochemical interaction between the two solute elements, magnesium and silicon. The observed contraction is associated with restricted solid solubility. It was also shown1 that the extent of the primary solid solubility did not follow the trends predicted by the lattice-distortion oncept." This again suggested that the solubility limits are strongly affected by the stability of the intermediate phases, I, 1, and X . In order to test the above hypotheses, lattice-parameter measurements of the fcc @-phase alloys were determined within the ternary system at a constant electron concentration (e/a = 1.30) and also at a constant zinc content. Alloys of predetermined composition were prepared from high-purity metals and melted and cast under reduced pressures of helium in quartz capsules. Since the weight losses were very slight and did not exceed one part in 2000, the nominal compositions listed in Table I were accepted without chemical analyses. The ingots were homogenized

Jan 1, 1964

By F. E. Minshall

FoR more than 30 years California has been one of the three leading oil-producing states. Present daily production of crude oil under curtailment, approximately 580,000 bbl., comes from three general areas: Los Angeles Basin, San Joaquin Valley, and the coastal region of Ventura and Santa Barbara Counties. This state produces approximately two-thirds of its oil from eight large fields, and obtains a daily average production of 48 bbl. of oil per producing well, whereas the average for the United States is but 8.15 barrels. During the closing stages of the first half of 1936, discovery of the Section Ten oil field was made, and credit goes solely to geophysical work. It is the first direct important discovery of oil in California that may be credited to geophysics. This discovery may furnish the cue to the means of discovering several fields in California, particularly in the San Joaquin Valley. It is a question, however, whether returns from geophysical work will play as important a part in the future supply of oil in California as have our former types of prospecting. Explobation Methods of prospecting have progressed in the oil industry through invention or improvement in scientific means of locating and defining structure and because of market improvements in drilling equipment. Present methods of prospecting include: 1. A detailed study of geology in an attempt to locate structural and stratigraphic conditions that would be favorable to the accumulation of oil. 2. Geophysical methods involving the use of the seismograph, torsion balance, magnetometer and electrical methods. (There is still much to be learned in California in the application of geophysical methods.) 3. Use of micropaleontology as an aid in correlation,. The principal improvements in drilling equipment are: 1. The Schlumberger dipmeter, which determines the direction of formation dip in an uncased hole.

Jan 1, 1937

By A. E. Nehrenberg

IN an earlier publication' it was shown that the.. shape assumed by a volume of growing austenite is inherited from the prior structure. The matrix grains of pearlitic microstructures are equiaxed, and austenite grows in an equiaxed manner in these prior structures. Martensite and bainite, on the other hand, have an acicular grain structure, and the austenite produced in such structures grows in an acicular manner. In the discussion of this paper' it was pointed out that in cold-rolled tempered martensite, austenite grows in an equiaxed, rather than an acicular manner. The results of an experiment carried out to arrive at an understanding of this behavior are illustrated by the micrographs. Fig. 1 shows the acicular microstructure produced by heating tempered martensite to a temperature within the Ac1-Ac3 range, 1350°F. When tempered martensite is cold rolled, then heated to the same temperature, the equiaxed structure shown in Fig. 2 is produced. A sample of cold-rolled tempered martensite heated at 1350°F just long enough for the formation of a small amount of austenite is shown by Fig. 3 to have an equiaxed (recrystallized) ferrite grain structure. The small particles of. austenite which formed at 1350°F in the equiaxed ferrite matrix are likewise equiaxed. Thus, the equiaxed growth of austenite in cold-worked tempered martensite is not a contradiction of the principles described in the previous paper, for the growth pattern reflects the matrix grain structure existing at the time of austenite formation. References A. E. Nehrenberg: The Growth of Austenite as Related to Prior structure. Trans. AIME (1950) 188, pp. 162-174; Journal of Metals (January 1950). 2 J. R. Vilella and R. A. Grange: Discussion of ref. 1. Trans. AIME (1950) 188, pp. 1378-1381; Journal of Metals (November 1950).

Jan 1, 1953

By Thomas L. Watson

The occurrence of zircon in pegmatites of acidic composition is recorded by many observers both in this country and abroad, and they form one of the most important geologic modes of occurrence of the minera1. As is well known, commercially the most important American locality for zircon is near Zirconia in Henderson County, North Carolina, where many tons of the mineral have been obtained from a kaolinized pegmatite dike 100 ft. wide and traced for 1 1/2 miles along the direction of strike N. 50" E. Zircon may be developed in pegmatites as inclusions in the principal rock-forming minerals, chiefly quartz and feldspar, and as a separate megascopic constituent in the form of grains and crystals not exceeding, as a rule, 2 in. in size, and usually smaller. In the Henderson County, North Carolina, pegmatite, zircon occurs in prismatic crystals with pyramidal terminations measuring up to 30 mm. in diameter, associated chiefly with the feldspar. In some of the apatite veins of Canada, which are closely allied to pogmatite dikes, zircon is reported in crystals upward of 6 in. in length and 2 in. and more in thickness. Zircon in large masses occurs in Virginia in the well-known pegmatites near Amelia in Amelia County, and near Gouldin in Hanover County. Both localities are in the middle eastern portion of the Piedmont Plateau province, and are separated by a distance of about 40 miles in a northeast-southwest direction. The rocks of both areas, including the pegmatite bodies, are in an advanced stage of decay, and the hard and moderately fresh rocks are concealed beneath a cover of variable thickness of rock decay derived by the normal processes of weathering. Exposures, there-

Jan 1, 1917

By J. B. Umpleby

The subject of reservoir energy and its efficient utilization has been well explored in many papers. The present effort, therefore, is limited to a summary of existing information combined with an emphasis of the probability that the relative importance of controlling factors will change with advancing knowledge. Consequently the necessity for flexibility in laws and regulations, inherent in the problem, is emphasized. Definitions Many terms have been widely used in the literature without having been specifically defined. For example, confusion exists in the use of ((reservoir energy" and "gas energy." The latter is much more limited in meaning than the former. Other terms have been variously used. Consequently, I shall preface my remarks with definitions of a few of the more pertinent terms. Reservoir energy is that force or forces, active or potential, that is native to the reservoir and has the power to move oil through the reservoir rock. The energy may result from expanding gas, from hydrostatic head, from the weight of overburden, or from any other source. Gas energy is the expansive power of gas when pressure is reduced. It is one type of reservoir energy. An oil reservoir is that part of a geologic formation or formations in which oil occurs in commercial quantities wholly surrounded by nonproductive rock. The essence of this definition is effective separation rather than remoteness and under it oil reservoirs may be superimposed in the same oil pool. Conservation of reservoir energy means primarily its maximum use in the production of oil. Unit operation is a plan of development and production, which embraces an entire oil reservoir under a unity of engineering control. It is distinct from unitization, which has to do with arrangements of organization and equities to make unit operation possible in areas of divided ownership.

Jan 1, 1934

By William E. Ford, Edward Salisbury Dana

296. Definition of Specific Gravity. - The specific gravity of a mineral is the ratio of its density * to that of water at 4' C. (39'2' F.). This relative density may be learned in any case by comparing the ratio of the weight of a certain volume of the given substance to that of an equal volume of water; hence the specific gravity is often defined as: the weight of the body divided by the weight of an equal volume of water. The statement that the specific gravity of graphite is 2, of corundum 4, of galena 7-5, etc., means that the densities of the minerals named are 2; 4, and 7'5, etc., times that of water; in other words, as familiarly expressed, any volume of them, a cubic inch for example, weighs 2 times, 4 times, 7.5 times, etc., as much rn a like volume, a cubic inch, of water. Strictly speaking, since the density of water varies with its expansion or contraction under change of temperature, the comparison should be made with water at a fixed temperature, namely 4' C. (39'2' F.), at which it has its maxi- mum density. If made at a higher temperature, a suitable correction should be introduced by calculation. Practically, however, since a high degree of accuracy is not often called for, and, indeed, in many cases is impracticable to attain in consequence of the nature of the material at hand, in the ordinary work of obtaining the specific gravity of minerals the temperature at which the observation is made can safely be neglected. Common variations of temperature would seldom affect the value of the specific gravity to the extent of one unit in the third decimal place.

Jan 1, 1922

By Julian Kennedy Edgar

THINKING that it may prove of interest to the Institute, I have prepared a short account of the blowing in and subsequent working of the "A" furnace of the Edgar Thomson Steel Works. This furnace was built for the purpose of making spiegel, but has been started and is now running on Bessemer iron. The shape and size of the furnace are shown in the accompanying drawing. It will be seen that the section is formed of lines making very small angles with each other. In fact, an arc of a circle can be drawn, from the top to the tuyeres, which will nowhere deviate more than two inches from the lines given. In building, also, great pains were taken to gradually round the angles, so that the most careful observer, standing in the crucible and looking upward, could not tell at what points the slopes changed. It will also be seen that the widest part of the furnace is almost exactly midway between the bottom and the stock line, The flattest slope is maintained for 20 feet above the crucible, and is about 1 s inch to the foot from the perpendicular. The furnace is lined with small brick throughout, and has six tuyeres four inches in diameter, which project seven inches inside of crucible. There are three Siemens-Cowper-Cochrane stoves, each 15 feet in diameter by 50 feet high. Blast is furnished by an upright engine with 32-inch steam cylinder, 84-inch air cylinder, and 48-inch stroke. The steam cylinder has balanced poppet valves, working horizontally. The steam valves are worked by a Porter link-movement in order to obtain a variable cut-off. The exhaust valves are worked by a separate eccentric. It is intended to attach a governor to the cut-off, but at present it is set by hand. The steam cylinder is

Jan 1, 1880

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By Robert L. Davidoff, Rodney D. Rosenkranz

In order to determine copper resource data and production costs for major market economy mines and deposits, the Bureau of Mines has performed detailed engineering and economic analyses on 271 of the world's most significant copper deposits. At the demonstrated resource level, copper potentially recoverable from these deposits is estimated to be 325 million metric tons, 180 million tons of which would be from Pacific Rim countries. Chile has the largest known copper resources of any country and accounts for nearly 45 percent of the copper avail- able from Pacific Rim countries. At $1.00 per pound, in January 1981 dollars, an estimated 80 million metric tons of copper are potentially economically recoverable from Pacific Rim deposits. At this same price, analyses indicate that these deposits could economically produce about 2 million metric tons of copper per year. Sensitivity analyses reveal that if operating costs were to decrease 25 percent, with copper at a price of $1.00 per pound, total copper economically recoverable from Pacific Rim countries could increase by about 10 percent; a 25 percent increase in operating costs could lower economically recoverable copper by 50 percent. Analyses also indicate that byproduct prices are important. If byproduct revenues increased 25 percent, at a copper price of $1.00 per pound, an additional 2 million metric tons of copper could be recovered; if byproduct revenues decrease 25 percent, about 5 million metric tons less of copper metal would be available. Since the January 1981 date of this study, inflation and decreases in copper and byproduct prices have greatly affected the profitability of the world copper industry. Many producing mines have curtailed or suspended production, and development of many non- producing deposits has been postponed.

Jan 1, 1982