Search Documents

By Richard McCaffery

THIS paper considers certain aspects of the acid Bessemer process, particularly in its relations to the duplex process-that combination in which the pig iron is first desiliconized and decarburized in acid Bessemer converters and then dephosphorized in basic open-hearth furnaces. The acid Bessemer process employs an acid-lined converter and produces an acid slag. The blow is usually thought to eliminate the silicon and manganese as oxides and then to burn off the carbon as carbon monoxide. On account, however, of the relatively large amount of metallic iron present in the converter, compared with the relatively small amount of the impurities it is desired to oxidize, the first reaction in the converter probably is the formation of iron oxide, which dissolves in the bath and acts as an oxygen carrier for the silicon and carbon. As soon as iron oxide is dissolved throughout the bath, the oxidation of silicon commences; but in the early stages of the blow the mass law would indicate that iron oxide must form first, and this oxide probably increases up to some saturation point. The molten metal in the converter from the early stages of the blow right through to its completion remains basic, while the slag produced is siliceous. This fact is shown by the corrosion of the acid bottom and the tuyeres, which is greatest at the tuyere orifice where oxidation is most active and where there is the most iron oxide. Why does this acid bottom corrode? Because it is attacked by a base. The thought, therefore, suggests itself, why not make the bottoms of basic or neutral material?1 As the converter slag is acid, those parts of the converter coming in contact with the slag should be acid; but those parts of the converter that are in contact with the molten metal saturated with metallic oxides should be basic or neutral. Bessemer operators have for some time tacitly admitted this condition, for the blast pressures have steadily increased with the object of keeping the metal in suspension, and so preventing bottom corrosion; if the molten metal were not basic, it would not attack an acid bottom. In addition, the tuyeres are bunched together at the middle of the bottom and a clear space is left around the outside of the bottom; if tuyeres are placed too near the side walls the

Jan 8, 1920

By P. D. Hunt, B. Tani, M. G. Chasanov, R. Schablaske

The Zn-Vphase diagram was studied by thermal. metallographic, X-ray, and sampling techniques. Three ternary phase equilibria were observed: Mutual solid solubilities in vanadium and zinc appear to be negligible. The liquidus line is retrograde from 670° to 756°C. 1 HE only information in the literature relating to the Zn-V system was a study of corrosion of vanadium by liquid zinc' and an examination of the effectiveness of zinc coatings in protecting vanadium-base alloys from oxidation at high temperatures.2 Establishment of the Zn-V phase diagram was undertaken as part of a study of transition metal solubilities in liquid metal solvents. Chemical, metallographic, thermal, and X-ray diffraction analyses were used to determine the diagram. MATERIALS AND EXPERIMENTAL PROCEDURES Vanadium (99.86 pct) in the form of powder and small chips was employed. Stick zinc (99.99 pct; major impurities: 10 to 15 ppm Pb and 20 ppm Cu) was used in the liquidus determinations and thermal analyses; zinc powder (98.80 pct) was used to prepare intermediate compositions. The liquidus lines were determined by chemical analysis of filtered samples of the saturated melts. The apparatus and sampling techniques were similar to those described by Martin, et al.3 The entire metal sample was dissolved to preclude analytical errors due to segregation on cooling. Vanadium was determined amperometrically, using iron (11) as the titrant,4 to an estimated accuracy of 1 pct. Standard techniques of thermal analysis were employed to examine alloy specimens contained in alumina crucibles under helium. Heating and cooling rates were about 1°C per min. At least five heating and cooling cycles over the range 420° to 700°C were performed for each of two Zn-15 pct V alloys. A Zn-0.2 pct V alloy was used in the determination of the eutectic temperature. The separation of intermediate phases from zinc-rich alloys was carried out by selective leaching with ammonium nitrate solutions. For further investigation of intermediate phases 1/4 in. diam powder compacts were prepared by pressing at 80,000 psi and were annealed in argon at 415" to 450°C for 10 days. Larger quantities of intermediate phases were prepared in sealed tantalum capsules heated in a rocking furnace. Temperatures were determined to an estimated accuracy of 0.5°C with a Pt/Pt-10 pct Rh thermo-

Jan 1, 1963

By Richard S. McCaffery

This paper considers certain aspects of the acid bessemer process, particularly in its relations to the duplex process—that combination in which the pig iron is first desiliconized and decarburized in acid bessemer converters and then dephosphorized in basic open-hearth furnaces. The acid bessemer process employs an acid-lined converter and produces an acid slag. The blow is usually thought to eliminate the silicon and manganese as oxides and then to burn off the carbon as carbon monoxide On account, however, of the relatively large amount of metallic iron present in the converter, compared with the relatively small amount of the impurities it is desired to oxidize, the first reaction in the converter probably is the formation of iron oxide, which dissolves in the bath and acts as an oxygen carrier for the silicon and carbon. As soon as iron oxide is dissolved throughout the bath, the oxidation of silicon commences; but in the early stages of the blow the mass law would indicate that iron oxide must form first, and this oxide probably increases up to some saturation point. The molten metal in the converter from the early stages of the blow right through to its completion remains basic, while the slag produced is siliceous. This fact is shown by the corrosion of the acid bottom and the tuyeres, which is greatest at the tuyere orifice where oxidation is most active and where there is the most iron oxide. Why does this acid bottom corrode? Because it is attacked by a base. The thought, therefore, suggests itself, why not. make the bottoms of basic or neutral material?' As the converter slag is acid, those parts of the converter coming in contact with the slag should be acid; but those parts of the converter that are in contact with the molten metal saturated with metallic oxides should be basic. or neutral. Bessemer operators have for some time tacitly admitted this condition, for the blast pressures have steadily increased with the object of keeping the metal in suspension, and so preventing bottom corrosion; if the molten metal were not basic, it would not attack an acid bottom. In addition, the tuyeres are bunched together at the middle of the bottom and a clear space is left around the outside of the bottom; if tuyeres are placed too near the side walls the

Jan 1, 1922

By Carl Zapffe

Because no rock outcrops exist in the Cuyuna district, it is necessary first to make a magnetic survey with a dip needle, or possibly with a sun-dial compass, and determine the area or belt of magnetic variations and the maximum lines of magnetic attraction. A dip-needle survey is quicker to make, is sufficiently accurate, and will suffice. Regardless of how poorly defined the magnetic attractions may be, it is important that they be determined. Even if drilling has developed ore on an adjoining property, the survey should not be omitted. Iron-bearing formation is indicated by the magnetic attractions, but whether or not ore exists must be determined by drilling. The maximum line of magnetic attraction offers the best place to begin drilling. If no magnetic attraction exists, nearby developments are the only guide; and if these also are lacking, drilling is governed by guess. Test-pitting is not employed in exploratory work because the surface is too deep. Tunneling cannot be used because the topography is not suitable. Exploration shafts are a waste of time and expense, because from every standpoint drilling with churn and diamond drills is the most applicable method for exploratory work. Light drilling equipment only is needed. Rarely have heavier drills been required, for seldom do holes exceed 400 ft. in depth, and about 100 ft. of this is in glacial drift which is easy to penetrate. The deepest hole is 1023 ft. Because of the steep inclination of the strata and the narrowness of the orebodies, many angle holes have been drilled, mostly at 60' to 70" from the horizontal and against the dip of the formation. Angle holes are most advisable. If after initial drilling the beds are of shallow dip, vertical holes or holes of any angle can be used. The total cost of drilling a property is much greater if only vertical holes are used because more holes must be drilled to obtain the requisite information than when angle holes are used. Many tests for variation in angularity of a finished hole have seldom shown more than 2'; therefore, such tests may with safety be abandoned. Because the orebodies are generally about 100 ft. wide and cross a 40-acre tract at a slight angle, and as the dips are usually about 70"

Jan 1, 1925

C.A. MITKE, *Bisbee, Ariz. (written-discussion-? ).--The advantages of the incline-slicing system have' been ably pointed out by Mr. Scott in his paper in the November, 1917, Bulletin, and also by Mr. P. B. Scotland in the Engineering & Mining Journal, Apr. 7, 1917. From the standpoint of efficiency and economy this method is far superior to the top-slice system as generally practised. However, as regards ventilation, and the danger of mine fires, it is just as necessary to use a mechanical ventilating system in mines worked by this method as it is in those worked by the horizontal top-slice system. Mechanical ventilation not only improves working conditions in top-slice stopes but, if properly designed for the particular mine in question, permits an immediate attack to he made in the event of a mine fire with a greater degree of safety to the men. In the course of time, incline top-slicing will probably take the place of the horizontal top-slicing system just as the incline cut-and-fill has superseded the horizontal cut-and-fill stoping method. While incline top-slicing has been tried in several districts on a very limited scale with inconclusive results, the Coronado is the-only large mine at which it has yet been thoroughly tested, and there it proved to be a complete success. As Mr. Scott's figures show, the tonnage has been more than doubled, with a simultaneous reduction in costs. As has been the history with all other innovations in mining, considerable hesitation will probably be shown in introducing this method in other mines. For example, when the incline cut-and-fill system was put forward as a substitute for the horizontal cut-and-fill stoping method many mining men of good repute were doubtful of its success and post-poned its introduction as long as possible, giving as their reason certain geologic conditions which would make the incline cut-and-fill impracticable. At the present time, most of the mining companies in the South-west, who in the past had used the horizontal cut-and-fill system, have already changed over, or are in the process of changing, and have proved that in the majority of cases horizontal cut-and-fill stopes can be successfully operated under the incline cut-and-fill system. Large horizontal cut-and-fill stopes can now be found in only a few exceptional cases, and

Jan 3, 1918

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By Olav Klomstadlien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, are the raw material base for Rana Mines, a division of the state-owned A/S Norsk Jernverk steel mill. The iron bearing minerals are magnetite and specular hematite. The magnetite/hematite ratio varies considerably both within each deposit and from one deposit to another. The ore bodies that lend themselves to mining have generally a thickness of 30-60 m grading 30-35% Fe and 0.15-0.25% P. The grain size varies from 0.05 to 2.5 mm. The fine grained ores are hard while the coarse grained ores are soft and easy to grind. The A/S Norsk Jernverk steel mill operates both a sinter and a pellet plant, and this necessitates production of two types of concentrates. The present flowsheet is shown in [Fig. 1]. The crude ore from the pits is crushed in a 1.07-m gyratory crusher with an open side setting of 12.7 cm. The crusher product is transported by rail to the concentrator located 25 km from the mines. The ore is fed by twelve 1.22 X 1.83 m vibratory feeders onto conveyor belts which carry the ore to a surge bin ahead of the autogenous mills. The feed rate is automatically adjusted to maintain a set power load at a level suitable for the ore type being processed. The mills operate in closed circuit with twelve dual-drum screens equipped with a 0.8-mm screen cloth. Oversize is returned by gravity to the mill feed while undersize flows to the gravity separation section which consists of Humphrey spirals in three stages. The ores are very heterogenous and analysis may vary quite considerably. The quantitative need for concentrate in the steel mill may also change rapidly. The process in the concentrator must therefore be easily changed, and consequently alternative process lines have been established. This is indicated with the dotted lines in the flowsheet. Apatite is removed by flotation by fatty acids to give a final sinter concentrate of 63% Fe and 0.020% P or less. Pellet concentrate contains about 65% Fe and less than 0.020% P. The fineness is about 1500 Blain.

Jan 1, 1981

By Daniel M. Bass, Paul B. Crawford

Laboratory investigations have been made to study the effect of variations in fluid characteristics, gas saturation, water saturation, and water injection rate on oil recovery by water flooding. Three synthetic gas-saturated crude oils having bubble points of 860, 1,540 and 1,885 psi were used as reservoir fluids. Repeated tests were made in which a and pack, saturated with water and synthetic oil, was produced by solution gas drive followed by water flooding at various pressure levels. Oil recovery by solution gas drive and subsequent water injection is shown to vary with the pressure and rate at which the water flood is conducted. The pressure at which optimum flooding conditions exist is shown to be a functiotl of the physical characteristics of the reservoir fluid. For the systems studied, increases in oil recoveries of near 10 per cent were obtained by flooding at the most desirable conditions. Va- riations in initial water saturations gave results similar to those in the literature. INTRODUCTION Most of the waterflooding studies investigating means of improving present exploitation processes have been conducted at low pressures with little effort to simulate reservoir conditions. Holmgren and Morse' performed a waterflooding study at 300 to 500 psi wherein the gas saturation was created by injecting gas, letting dissolved gas evolve from the oil, and then flushing the core with "live" oil until the desired gas saturation was obtained. Their results show increasing oil recoveries with increasing gas saturations. Data presented by Guerrero' and Kennedy, et al, indicate that in some instances water flooding at approximately 500 psi below the original bubble point results in a lower residual oil saturation than is obtained when water flooding above the bubble point. In their work gas saturations were created by primary depletion. By correcting low pressure flooding data for fluid shrinkage, Dyes found that a maximum oil recovery may be obtained by flooding with initial gas saturations of from 7 to 12 per cent. The purpose of this work was to determine the variations in oil recovery caused by initiating a waterflooding program at various stages of primary depletion of a core. This is a part of a more comprehensive study of obtaining criteria for determining when to initiate a pressure maintenance program and what fluids to in-ject. EQUIPMENT A schematic diagram of the apparatus is shown in Fig. 1. Fluid transfer was accomplished with metering pumps. Pressure control was ob-

Jan 1, 1957

By N. W. Sager, H. W. Mossman

The arrangement and general dimensions of the reverberatory furnaces and waste-heat boilers for the Nos. 2 and 3 smelting units at the McGill plant of the Nevada Consolidated Copper Corporation are shown in Fig. 1. Each of the two reverberatory furnaces has its own set of waste-heat boilers, and before February, 1932, each furnace, when it was in operation, delivered waste-heat gases to its own boilers only. In January, 1933, the idea was suggested of using some of the waste-heat boilers as economizers to operate in conjunction with the waste-heat boilers that were generating steam. The execution of this idea gave rise to the gas-flow scheme depicted in Fig. 1, the advantages of which were obvious, particularly so in view of the fact that for some months prior to the adoption of this scheme the smelting had been confined to No. 2 furnace, with No. 3 furnace and its boilers idle. The waste-heat gases from No. 2 furnace pass through the boilers serving this furnace as steam-generating units, thence through the original exit duct to a point where a bulkhead diverts the gases in a reverse direction through two of the boilers of No. 3 furnace. After the gases have traversed these two boilers, another bulkhead placed in the duct between No. 3 furnace and its boilers causes them to traverse still one more boiler, from which the gas path leads to the stack. In this scheme the last three boilers traversed by the gases, i.e., the boilers behind No. 3 furnace, function as economizers and preheat the feed water for the two steam-generating units directly serving No. 2 furnace. This discussion will give consideration to the results obtained in waste-heat recovery by the scheme shown in Fig. 1, and, further, will compare these results with those obtained before the boilers of No. 3 furnace were set up to act as economizers, but before going into the detail of heat generation, distribution and recovery, will present some additional details of the equipment. All boilers in this waste-heat plant are of the Stirling type. The two behind No. 2 furnace, acting as steam-generating units, of class 13, are 40 tubes wide and rated at 1112 boiler hp., while the three boilers behind No. 3 furnace, acting as economizers, are also of class 13, but 28 tubes

Jan 1, 1934

By Leslie Burris, J. C. Hesson

The diffusivity of uranium in liquid cadmium has been measured as a function of temperature by the capillary -bath technique. The diffusivity measurements were made at 4509 500°, 575º, and 650°C, over which temperature range the diffusivity of uranium varied from 1.3 to 2.3 x 10-5 sq cm per sec. The diffusivity of uranium in cadmium was less than that predicted by the Einstein-Stokes equation. VERY little information is available on the diffusivity of uranium in liquid metals. Bonillal has reported a single measurement of the diffusivity of uranium in bismuth. Measurement of the diffusivity of uranium in cadmium was undertaken, not only to supply data in an area in which a dearth of information exists, but also because of a need for this physical property measurement in connection with mass transfer studies now underway in the U-Cd system at Argonne National Laboratory. The capillary-bath method used in this work has been successfully used by other workers2"4 to obtain diffusivities in liquid metal systems. Although considerable experimental technique is required to obtain reliable diffusivity measurements, the basic information required is only that of temperature, capillary tube length, the initial and final compositions of the alloy in the capillary tube, and the composition of the bath into which the solute element is diffusing. From these measurements, diffusivities may be calculated using Fick's law. The diffusivity equations are presented in the Appendix. Equations which are often used to predict diffusivities in dilute solutions5 are the Einstein-Stokes equation: D= (kT)/(6pµr) and the Eyring equation: D = (?,kT/?y?zp), where D= diffusivity (sq cm per sec), k = Boltzman's constant, T= temperature ("K), p = viscosity (poises), r = radius of diffusing molecule or species (cm), and A,, Ay, and A, are the diameters of the diffusing molecule in the three axial directions. For round molecules, the Eyring equation gives values which are 37r times larger than the Einstein-Stokes equation. In this work, the experimental values were compared to the Einstein-Stokes equation. Experimental values of diffusivities in liquid metal systems usually lie between those predicted by the Einstein-Stokes and Eyring equations. The viscosity values for cadmium were obtained from the Liquid Metals Handbook.6 EXPERIMENTAL APPARATUS AND PROCEDURE The general procedure employed consisted of rapidly immersing in a molten cadmium bath containing a negligible amount of uranium a capillary

Jan 1, 1963

By Raymond M. Howe

Some time ago, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furrace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after.4 years' service so a steam-pressed lining- was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion. The fifth reply stated that the present "hard-burned" hand-made furnace lining had worn away very uniformly to the depth of only 5 in.

Jan 1, 1920

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By E. D. Gardner

Apparently the widespread agitation for the codification of our mining laws has had its effect, and it is quite possible that Congress will take up the question during this present session. The greatest objection to our present statutes pertaining to metalliferous deposits seems to be directed against the law of the apex. Those who are not in favor of changing this law are very far in the minority and they apparently realize that it is useless to urge its retention. Next in importance to the repeal of the law of the apex, seems to be a widespread advocacy for the repeal of the law requiring discovery of mineral before a valid location of a mining claim can be made. To a lesser extent there appears to be a desire to have the law changed so as to allow patent for claims without mineral discoveries. The purpose of this article is to review the arguments in favor of the proposed change of the discovery requirement, to show some of the evils that may be expected to result therefrom, and to consider whether a system may be devised to correct the undesirable features of the present law in this respect and at the same time not expose the mining fraternity and the general public to the evils which would result from the repeal of this fundamental requirement. Under the law as at present framed, the validity of a mining location is dependent upon the fact of discovery of mineral within the boundaries of the land claimed. " * * * but no location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located" (Sec. 2,320, U. S. Rev. Stat.). All authorities agree that discovery is the source of the miners' title. Lindley, in his valuable work on Mines (3d Ed., Sec. 335), lays down the rule in part as follows: "Discovery is the initial fact. Without that no right can be acquired. * * * Such discovery must precede the location, or be in advance of intervening rights. The proof of recording and marking a claim will not authorize the court to presume a discovery." As is well stated by the U. S. Supreme Court in Erhard v. Boaro (113 U.S. 536):

Jan 1, 1917

By James H. Gardner

It is a striking fact in the domestic oil statistics of 1926 that with an increase in production of 13,000,000 bbl., there was nevertheless a lowering of both crude and gasoline stocks. It was the first reduction in the last eight years. In 1918, the last year of the war, stocks of crude and refined products were lowered 16,000,000 bbl., but in the following seven years stocks were increased 350,000,000 bbl., due largely to the phenomenal crop of major pools discovered in 1923. The big pools of that year coming as they did through some curious coincidence unprecedented in the oil industry, not only piled up a sudden increase of stocks at a time of large imports but they continued to add their quota to an increase of storage until 1926. With an increase in crude production, according to the Oil and Gas Journal, from 760,000,000 bbl. in 1925 to 773,000,000 bbl. in 1926, and an increase in cracking facilities of about 30 per cent., there was a draft on storage of 22,300,000 bbl. of crude and 1,000,000 bbl. of refined. Crude and refined changed from a stock surplus of 29,130,000 bbl. in 1925, to a deficit of 23,300,000 bbl. in 1926, or a differential total of 52,430,000 bbl. With a stock reserve of 541,700,000 bbl. of crude and refined oil in 1925, the amount drawn from storage was not large in percentage but it marked an important contrast with previous years. It meant a year of stability in prices and a sound condition in the industry. The indicated domestic demand increased from 695,120,000 in 1925 to 743,360,000 in 1926, (7 per cent.), 1 per cent. of which was due to California fires. Most of the gain in consumption was due to the increased demand for gasoline. There was little comparative change in the combined imports of crude and refined oil. There was an increase in exports of 17,200,000 bbl. (1.5 per cent). A petroleum balance sheet for 1926 and a comparativl sheet for the last two years, production in the United States by major districts and pools, and a list of imports are given in Tables 1 to 5, inclusive.

Jan 1, 1927

By R. H. Richman

Coarse-grained Fe-Ni-C martensites formed at subzero temperatures were strained in compression at room temperature and the plastic deformation modes examined as a funclion of carbon content. At very low carbon levels, defovmation occurs hy wavy slip; commencing at about 0.05 pct C, mechanical twinning accounts for an increasing proportion of the plastic flow. Beyond approximately 0.4 pct C the deformation appears to be entirely by mechanical twinning. The habit planes of the operative twin modes were determined to be (113), (0131, and "(089)" in decreasing frequency of occurrence. Some of the implicaticms of Ihe o6served deformation modes upon the structure and properties of ferrous martensites are discussed. METALLURGISTS have long sought to explain the mechanical properties of ferrous martensites, particularly the extraordinary hardness and strength of the high-carbon varieties. Until recently the lack of precise knowledge of the structure of martensite crystals was the most serious barrier to understanding; however, the advent of thin-foil techniques for transmission electron microscopy has removed much of the mystery from martensite structure. Observations by Kelly and Nutting,"' and many others since, indicate that Fe-C based martensite crystals are internally twinned to a degree dependent upon the carbon content, and that a martensite plate containing 0.8 wt pct C or more consists of a stack of twin-related lamellae with each lamella on the order of l00A thick. Such a structure would be expected to influence greatly all aspects of metallurgical behavior, and many of the properties of Fe-C based martensites have been rationalized accordingly. Recent independent experiments led Winchell and cohen3 to conclude that the strength of ferrous martensite is derived primarily from solid solution hardening of the iron lattice by interstitial carbon atoms. Strength contributions from precipitation, dislocation-atmosphere interactions, clustering, short-range order, crystallite size, and so forth, were considered to be of secondary importance. In the view of Winchell and Cohen, the twinned structure of martensite serves mainly to limit the effective length of dislocation lines in the lattice, and thereby confers an added measure of hardening. Few properties of metallic crystals are as sensitive to metallurgical structure as are deformation mechanisms. It is somewhat surprising therefore, that, except for metallographic evidence of mechanical twins in strained martensite,4 no systematic examination of plastic deformation

Jan 1, 1963

By Dr. O’Neil Thomas J., Donald W. Gentry

"There is nothing so disastrous as a rational investment policy in an irrational world. " John Maynard Keynes INTRODUCTION The principles of time value of money concepts were discussed and illustrated in Chapter 3. The importance of time value of money and the role it plays in the discipline of engineering economy have been well established. Chapter 9 further illustrates that project evaluation criteria that fail to consider this aspect are seriously deficient in providing appropriate capital budgeting decisions. Obviously future project receipts and expenditures must be discounted to permit valid comparisons with current cash flows. Although the concept of discounting is widely accepted, the selection of the appropriate discount rate has been the source of considerable debate and much disagreement. This chapter, then, provides an overview of the theoretical and practical considerations for determining or calculating the appropriate rate for discounting, the corporate cost of capital. Note specifically that the assumption of constant business risk among the various investment alternatives is maintained throughout this chapter. THE INTUITIVE APPROACH The fact that interest exists suggests that all money has a cost associated with its use. The cost of this money may be the result of either explicit or implicit charges or some combination of the two. Any time an individual or a firm consumes less than the total earnings generated in a given time period that individual or corporation has either consciously or unconsciously decided to "invest" these excess funds in some type of activity. For instance, the individual or corporation may decide to invest the excess funds in tangible property, place the funds in a money market account, or simply keep these funds in cash. In any case, these funds have been invested in some type of activity which promises the investor some return on the invested capital. Remembering that the firm's primary objective should be the maximization of shareholder wealth, then intuitively it seems reasonable to suggest that the firm should not invest in any project where the anticipated return does not exceed the cost of funds (capital) committed to the project. Indeed, if the firm always invests in projects having returns in excess of the cost of capital committed to them, then the wealth of the firm (as measured by the price of common stock) should be in-

Jan 1, 1984

By Emil Gathmann

Through wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot. Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium, there is no commercial reason why all steel should not be thoroughly degasified. A degasified steel being provided, the method of freezing or solidifying the liquid steel into an ingot, and the subsequent working into blooms and thence into various products, is of great importance in reducing the crop or scrap portion of the steel, due to segregation and pipe. How to ac-

Jan 1, 1916

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a very general loosely used term that includes virtually all finely divided types of limestone as well as burned forms of lime. However, actually (and according to Webster) lime is only calcined limestone (known as quicklime, calcium oxide, or calcia). It also embraces the secondary product of quicklime-namely hydrated lime or slaked lime (calcium hydroxide). Fundamentally there are two basic types of limestone-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts in terminology. The only difference is that the dolomitic types are a combination of the elements, calcium and magnesium, whereas high calcium limes contain only 0.5 to 2 pct of magnesium. Both types, which are made through calcination at high temperatures, are shown chemically as follows: [ ] In the above reactions either type of limestone is burned (calcined) in furnaces known as lime kilns so that the carbon dioxide content of the stone is expelled as a gas. With high calcium limestone 44 pct of the weight of the stone is lost; with dolomitic limestone the loss is 48 pct. Also, both reactions are chemically reversible since quicklime absorbs carbon dioxide readily and in so doing transforms itself back to the original carbonate form. Most quicklimes correspond in size to the original rock, which varies from one to eight inches, depending upon the type of kiln employed. Slight shrinkage occurs during calcination. A few limestones when calcined will decrepitate (break down) into a fine powdery form; however, chemically it is the same as the pebble or lump-sized material. For some uses the lumps of quicklime are pulverized and packaged. Since quicklime has great affinity for moisture and carbon dioxide, it is perishable. When it absorbs moisture and CO2 slowly from the atmosphere, the resulting product is "airslaked." Consequently, it must be stored in dry, moisture-proof areas that are free from CO2. Because of its fugitive nature, it is usually consumed within a few weeks after manufacture. A more stable form of lime is hydrated lime-commercially made by adding water to the quicklime until the lumps break down into a fine, white powder. This product, which is usually packaged, can be stored more safely; and many of its uses are interchangeable with quicklime. The irreversible chemical reactions of hydrated lime for both high calcium and dolomitic types are: [ ]

Jan 1, 1960

By John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 36 tons of water for each ton of coal produced, while bituminous mines average about 5 or 6 tons. Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. But it must also be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1973