Search Documents

G. W. TRAER (author's reply to discussion*).-Prof. Parr's discussion develops two points, upon which it seems desirable to comment. First, as to putting through a large enough tonnage to secure economic operation. At each manipulation of each oven 1500 1b. (680 kg.) of coal will be charged and the resultant coke discharged from a like amount of coal. . Sixteen slabs will be discharged at each manipulation, each approximately 5 ½ in. by 11 in. by 6 ft. (14 cm. by 28 cm. by 1.8 m.). The operating schedule of a commercial plant, based upon our observations and calculations, indicates a "through put" of at least 12 tons of coal per day for each oven. We have made these figures conservatively and feel confident of materially exceeding them in a fully developed operating system. Our oven plant, with containers, will not cost as much as high-temperature plants of the same capacity. They do not require container equipment; but this is much more than offset by the cost of the great basal heat regenerative flues. Our operating requirements are quite susceptible to the application of mechanical devices and we believe our labor cost will be well within the necessary limit. Second, as to Fig. 1 in my paper, showing the specific gravity' of the tar. It Was not intended to show that the specific- gravity of -the tar rises With decreasing heat, since of course the contrary is the fact. One of the curves shows the relation between temperature and specific gravity and the other the relation between temperature and- yield. Our consulting engineer prepared the chart according to his customary method for showing two dimensions.

Jan 1, 1919

By Sir John Cadman

Since my previous review of the Persian fields, presented in 1929,' considerable progress has been made. The main feature of drilling development has been the delimitation of the Haft Kel field and its extensions. Although the limits have not yet been reached, a productive area of about 40 square miles has already been proved and it is now certain that the field will be of the same order of importance as the Masjid-i-Sulaiman field. Production to main pipe line from Haft Kel was begun in November, 1929, and to date about 4,500,000 tons have been produced. Normal production has continued from the Masjid-i-Sulaiman and Naft Khaneh fields. The search for oil in horizons below the main producing limestone is perhaps the most interesting and important exploratory drilling work in progress. Promising results have been obtained in the first well deepened in the Masjid-i-Sulaiman field with this objective, and the exploration of these lower formations is being continued. In this connection an allied program of geochemical research work on the nature of the oils and oil-bearing rocks of different horizons is at, present being undertaken. Masjid-i-Sulaiman Field Since the Haft Kel field was brought into production in 1929, production from Masjid-i-Sulaiman has been reduced in order to equalize to some extent the producing lives of the two fields. The production for the last four years has been as follows: m Approximate Equivalent in TonB Barrels 1929 5,434,071 38,038,497 1930 4,925,869 34,481,083 1931 4,248,086 29,736,602 1932 Approximately 4,500,000 31,500,000

Jan 1, 1933

By J. D. Sudbury, J. E. Landers, D. A. Shock

The external corrosion of casing is one of the most important problems facing the present day production man. A 1953 NACE report' estimated the annual cost of casing corrosion at $2,200,000 in 22 fields studied. The fields represented only 10 per cent of the wells in the United States. It was significant that 77 per cent of the failures reported were due to external corrosion. A variety of means for combatting the casing corrosion problem have been discussed in papers such as the NACE survey' mentioned previously. No attempt to revicw these will be made in this paper. Thc scope of this paper has been limited to a discussion of the following major items: (I) an instrument for studying external electrolytic corrosion; (2) use of this instrument to determine the quantity of protective current required to prevent corrosion of casing; and (3) problem of accelerated external corrosion of the oil string at the base of the surface string. ELECTROCHEMICAL MECHANISM OF CORROSION It IS gcncrally belleved that one major cause of external corrosion is the existence of electrolytic cells operating between various formation waters. A theoretical discussion of the role of earth potentials in casing corrosion has been presented by L. de Witte and F. J. Radd.2 A brief picture of the electrolytic corrosion action between two differcnt formations (A and B) is presented in Fig. I. This picture is a review to many but is given to insure clarity. In the anode area, oxidation takes place as iron ions go into solution in formation A as a product of corrosion. In the cathode area. reduction takes place and hydrogen atoms are formed at the boundary between the pipe and formation B. The flow of electrons. as indicated. is into the pipe at the anode or corroding area and out of the pipe into the formation at the cathode. In order to conform with regulations of this journal, the flow of a conventional current (I! is also indicated in this sketch. All subsequent references will be to this so-called conventional current flow and will be indicated by the symbol (I). As this action takes place the layer of hydrogen developed on the cathode offers a resistance to the flow of current in the cell. It is said (hat the cathode has been polarized. This polarizing film can be rcmoved by addition of a so-called dcpolarizing agent which reacts with and removes this hydrogen film. Such an agent must be present in ordcr for this corrosion reaction to go at a rate sufficient to cause a severe corrosion problem. The two common depolarizing agents are: (I) oxy-sen. which readily reacts with hydro gen to form water, and (2) certain bacteria which use atomic hydrogen as part of their life process. It is not difficult to explain the presence of these agents. Oxygen may be present in some very shallow formations. Sulfate reducing bacteria are found to exist in nearly any ground where mud pits might be dug. THE CASING POTENTIAl-PROFILE Instrumentation A sketch of the equipment* uscd in determining casing potential profiles is shown in Fig. 2. The tool is run in the hole using a hoist truck with a three-conductor cable. This tool must be run with tubing and rods out of the hole and should be run with the flow line disconnected. By proper choice of electrode size it can be run in any size casing. The electrodes must be run in an open hole or a hole filled with oil. Measurements cannot be made while immersed in water. The tungsten carbide-tipped knives serve as the electrical robes and arc spaced 25 ft apart. The potential difference along a 25-ft section of casing is measured with a potentinmeter to an accuracy of about 5 mv. Current flowing in the pipe can then

Jan 1, 1956

By J. B. Cheatham

Applications of the mathematical theory of plasticity promises to lead to the solution of many drilling and rock mechanics problems. ,Because of mathematical considerations, the inelastic behavior of rock has frequently been represented by a perfectly plastic model in conjunction with a yield criteria of the Coulomb or Mohr type. The totality of all stress states for which a solid ceases to behave elastically can be represented as a limit surface in stress space. ,Probing of such limit surfaces indicates details of strain hardening which are not provided by the standard triaxial testing procedure. Probing tests of the limit surfaces have been performed on Cardova Cream limestone to provide data for extending plasticity theory to cover situations in which consolidation and strain hardening are present. Test results indicate that this highly porous limestone undergoes a permanent volume decrease when it is subjected to hydrostatic pressures in excess of 3,500 psi. A virgin sample tested under a confining pressure of 1,500 psi has a yield strength of 1,700 psi; however, if the sample is subjected to a consolidation pressure of 5,000 psi, before testing at 1,500 psi, the yield strength is raised to 2,300 psi. Thus, both consolidation and strain hardening are important considerations in describing the mechanical behavior of this limestone. Tests conducted with the axis of the core having different orientations indicate that this rock is also anisotropic. Portions of the initial and subsequent limit surfaces are determined for samples loaded either perpendicular or parallel to the bedding planes. INTRODUCTION Previous experimental work in rock mechanics indicates that no mathematically tractable constitutive theory is inclusive enough to describe the mechanical behavior exhibited by all types of rocks under all conditions of stress and temperature. Indeed, the type of deformation encountered in a single type of rock is known to depend upon the stress and temperature conditions in the rock during deformation.l-5 Certain rocks and minerals, notably those minerals composed of ionic salts, have been shown to exhibit plastic deformation when tested under conditions of high confining pressure.2 Since the mathematical theory of plasticity provides simplifications over the theory of elasticity in certain types of problems, such as those in which limit analysis can be applied, it is of interest to know under what conditions plasticity theory may be applied to rock mechanics problems. The following factors determine the nature of the deformation a particular specimen will undergo: (1) the microscopic structure of the rock, i.e., the structure visible under an optical microscope, including number of phases, porosity, distribution of phases, (2) the mineralogical structure of the solid phases, (3) the conditions of stress and the rate of change of stress and (4) the temperature. Extensive experiments on Yule marble, Carthage marble, Solenhofen limestone and other calcerous rocks indicate that these relatively nonporous rocks deform plastically under certain conditions of loading, and creep under other conditions of loading.l-3 This study is concerned with the behavior of Cordova Cream limestone (Austin chalk) which is also composed almost entirely of calcite and thus has the same mineralogical composition but, because of a rather large porosity, it possesses a different microscopic structure. This investigation was undertaken to learn if Cordova Cream limestone deforms plastically despite the embrittling effect of the pore spaces, and to provide data which can be used to determine whether the mathematical theory of plasticity can describe the mechanical behavior of Cordova Cream limestone. A brief discussion is given of some of the underlying principles of plasticity theory concerning stress space and limit surfaces. Strain hardening is defined and a discussion is given of how the mechanical behavior of a material can depend on the previous history of the loading. This is followed by a description of the experimental procedures

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By J. B. Agan, R. J. Fernandes

This paper utilizes the layered-system approach, modified to include areal sweep efficiency, to determine the miscible-slug size required and to predict the perfort7zance of a miscible-slug process in a highly stratified reservoir having a permeability variation of 0.76. The slug size in each layer was determined from theoretical calculations and laboratory data which showed that, to maintain miscibility in the reservoir, the slug size had to be 8.2 per cent of the floodable hydrocarbon pore volume. Economic considerations, however, such as the value of the miscible product injected, the cost of injection and the cost of reprocessing the miscible product, limited the amount of miscible product which could be injected into the lower-permeability layers. This resulted in subjecting only 60 per cent of the reservoir to a slug size sufficient to maintain miscibility. Utilizing the relationship of producing gas-oil ratio and areal sweep efficiency as a function of pore volume injected (as obtained from data published by Dyes, Caudle and Erickson2), the theoretical performance was determined. This prediction is compared with actual performance to date. Actual performance reflects an increasing percentage of tniscible product in the produced fluid to a particular level, which remains static for a short period and then increases again to a higher level. This performance suggests that the reservoir has performed as a layered system. It is concluded that the layered-system approach can be used to predict performance in a highly stratified reservoir and that economic consideration is a limiting factor in determining the amount of the reservoir which can be miscibly swept. INTRODUCTION The Paloma zone in the Paloma oil field, Kern County, Calif., is comprised of several sand members separated by siltstone, shale and/or cherty sections. Rapid facies changes within the zone indicate that the sediments were deposited in a "near shore" environment. As a result, the Paloma sands have a high permeability variation, and the Paloma zone is comprised of several sand reservoirs. Since one of the sand reservoirs containing crude oil was not receiving the benefits of gas injection, consideration was given to recompleting certain wells to isolate the sand in order to perform a miscible-phase injection project and, thereby, to increase its ultimate oil recovery. Before proceeding with the project, a review of the literature was made to determine the miscible-slug size that would be required to maintain miscibility throughout the displacement process. Although the review showed that considerable information was available for homogeneous systems, insufficient information was available to determine slug-size requirements and to predict performances for a highly stratified reservoir. This paper has been prepared to describe the method used to determine the miscible-slug-size requirement and to predict the performance of the miscible-phase injection project initiated in the Paloma oil field. Although the Paloma project has only been in operation since Aug., 1958, sufficient production history has been obtained so that a comparison can be made with the predicted performance. DESCRIPTION OF RESERVOIR The reservoir in which the miscible-phase project was initiated in the Paloma field is shown on Figs. 1 and 2. Reservoir properties are as follows: average sand thickness, 43 ft; porosity, 19.1 per cent; water saturation, 47.2 per cent: oil viscosity, 0.328 cp; reservoir temperature, 250°F; reservoir pressure, 3,500 psi: gas saturation, 21.2 per cent at time of miscible product injection; and total net hydrocarbon pore volume, 19,993,000 reservoir bbl. LIMITATIONS The method described herein utilizes a layer-system approach, where injection into and production from each layer is assumed to be proportional to the layer's fractional capacity. The effects of increased fluid mobility on injection and production rates, in layers which have had breakthrough, are not reflected in this method. There has been considerable controversy over the slug size necessary to maintain miscibility throughout the displacement process. In this method, the slug-size

By J. V. Emmons

THE processes of hardening and tempering steel tools within the past 15 or 20 years have been so developed that the forward strides of the industry can scarcely be followed by the average observer. No small part of the credit for this phenomenal advancement is due to the improved methods of measuring the high temperatures necessary. Pyrometry has made possible the discovery and use of the many special alloy steels the wonderful properties of which are revolutionizing the industrial world. So sensitive are these steels to changes of temperature that often a variation of only 10° F. at a critical point of the heat treatment will cause the failure of the tool. In the tool-manufacturing industry today, accurate control of the many heating operations is imperative. The principal processes in the manufacture of tools that require accurate high-temperature measurements are annealing, carburizing, hardening, tempering, and laboratory research. Several other operations, such as forging and straightening, use rougher and correspondingly less accurate methods. These operations are usually performed in the following approximate ranges of temperature: DEGREES F. DEGREES F. Annealing 1000 to 1700 Tempering 200 to 1200 Carburizing 1400 to 1000 Forging 1400 to 1800 Hardening 1400 to 2500 Straightening 300 to 1300 Laboratory research covers the entire range. Annealing and carburizing are usually done in muffle or semi-muffle furnaces, heated with coal, coke, oil, gas, or electricity. Many of them are of large size, holding several tons of steel at one charge. Both indicating and recording pyrometers are used. The recording instruments are generally of the thermoelectric type, while for the indicating, both optical and thermoelectric are used.

Jan 9, 1919

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 4, 1915

By C. R. Hocott

THE distribution and movement of fluids in oil reservoirs are influ-enced to a great extent by capillary forces, which depend upon the size and shape of the pores in the reservoir rock, the surface characteristics of the rock, and the interfacial tension between the fluid phases. This paper presents the results of an investigation of the interfacial tension between salt water and crude oil containing dissolved gas under reser-voir conditions. APPARATUS AND PROCEDURE In the preliminary phases of this investigation, it was found that a scum formed at the oil-water interface, which made measurement of interfacial tension by either the ring or capillary rise methods unreliable. Accordingly, the drop-weight method, in which a fresh interface is con-tinuously formed, was selected. In this method, a tip through which drops of one fluid can be expelled is immersed in a second fluid. At the instant that the drop becomes large enough to fall, the gravitational force tending to pull away the drop exactly balances the interfacial force tending to hold it. From the size of the drop, the dimensions of the tip, and the density of the two fluid phases, the interfacial tension may be calculated. The apparatus consists of a circulating pump for bringing the oil to equilibrium with gas at the desired pressure, a displacement pump for forming the drops, an interfacial tension cell in which the drops are formed, and a density cell to determine the density of the oil. The density of the water is determined separately in another apparatus. A flow diagram of the assembled equipment is shown in Fig. 1.

Jan 1, 1938

By G. W. Thomas

A simplified mathematical model of underground conduction heating in a system of limited permeability is presented. The model applies to underground retorting of oil shale, or to reservoirs containing extremely heavy oils. We assume that heat is introduced at a constant rate into a horizontal fracture which communicates between wells. The radial temperature distribution along the fractured surface is approximated by a step-function. Heat transfer away from the fracture is assumed to be by vertical conduction, and all convection effects are neglected. The model also takes into account the possible temperature dependence of thermal conductivity. A general expression for calculating the growth of the step-function temperature distribution with time is derived. The use of this expression and solutions to the one-dimensional heat equation make it possible to construct isotherms. Expressions for calculating .oil recovery, well spacing and heat efficiency are also given. An example calculation is presented for the conduction heating process in oil shale. Finally, the effect of the heat transfer coefficient between the gas and the fracture boundaries is investigated. INTRODUCTION Thermal recovery processes of oil recovery fall into the four general areas of hot fluid injection, forward combustion, reverse combustion and conduction heating. The first three of* these processes have been rather extensively studied in the past decade from both the experimental and theoretical points of view. As a result, it is possible to make reasonable engineering predictions and analyses of these processes. Little attention has been devoted, however, to the conduction heating process other than to note its possible utility.I To a certain extent, conduction heating cannot be divorced from the other regimes cited above, insofar as these provide the source of heat energy. In the conduction heating process, heat is introduced (either by combustion in the forward or reverse mode or by hot fluid injection) into a small fraction of the total reservoir thickness. This fraction may be either a streak of high permeability or an interwell fracture. Heat penetrates by conduction into the adjacent, less permeable regions of the oil-bearing rock, where the direction of conduction is essentially perpendicular to the streak or fracture. The heated product then drains by gravity or is gas driven to production wells. Conduction heating is probably most applicable to systems containing immobile bitumens such as tar sands and oil shale deposits and perhaps to low-permeability reservoirs containing highly viscous crudes. The mechanism also acts in combination with other thermal processes where fingering or overriding of a bed occurs. It seems probable that in at least one field test, conduction heating of this type was very influential.2 In this presentation we give a first approximation to some of the quantitative aspects of conduction heating. Marx and Langenheim3 treated a similar problem where they focused attention upon the injection interval, which spanned the total reservoir thickness. In their model, conduction heat losses to the bounding media imposed a practical limit on the calculated heated area. In the present study, however, we shall confine the injection interval to a small fraction of the reservoir thickness and assume it has no heat capacity. We therefore direct our attention to regions outside the injection interval into which the conduction of heat is beneficial. In particular, we will endeavor to locate specific isotherms in the media bounding the injection interval. Furthermore, we will construct our model to allow the thermal conductivity to vary arbitrarily with temperature. Thus the model will be applicable to underground retorting of shale where variations in thermal conductivity may be important. THEORY We consider the rock matrix to have no or, at best, a very limited permeability; consequently a

Jan 1, 1965

By Gordon H. Geiger, John M. Svoboda

One mechanism of metal penetration into mold aggregates by cast steels is vapor state mass transport. In order to further understand and quantify this mechanism, the steady-state diffusion of metallic vapors was studied at 1250" to 1600°C in controlled oxygen pressure atmospheres by measuring the weight loss from a metal bath whose vapors were allowed to diffuse through a porous aggregate compact held at constant temperature. Mass transport rates substantially greater than those predicted from the assumption that the vaporizing species was the elemental metal vapor were observed. Vaporization rates were found to increase with an increase in the oxygen partial pressure in the gas atmosphere with maximum vaporization occurring at oxygen partial pressures just below those in equilibrium with a liquid oxide layer at the given temperature. When the liquid oxide layer was present, no vaporization was observed. Metal carbonyls were ruled out as the vapor species involved because of their thermodynamic properties. The species with the enhanced volatility were deduced to be gaseous metal-oxygen molecules, probably the polynuclear oxides (FeO)2 and (Mn0)2. Diffusion followed the ordinary diffusion mode, and Knudsen diffusion is not important in normal foundry molds. The interdiffusivities of the metallic vapors and the mold atmosphere, through the porous aggregates, were measured. The effective interdif-fusivity of the vapor species and mold atmosphere through the aggregate may be expressed as follows: Deff,12 - — where E is the void fraction of the aggregate and 7 is the "tortuosity factor". Aggregate material had no effect on diffusion rates, and the only relevant parameter was the void fraction. Values for 7 ranged from 3 to 6 for normal foundry aggregates with 4 being considered a good representative value. An area of interest in high-temperature metallurgical processes which has received little attention in the past is the diffusion of metal vapor species in porous aggregates. Research into the metal penetration phenomenon' in foundry molds has shown that a major penetration mechanism is the vapor transport of metallic species into the porous foundry sand molds, followed by condensation of metallic films on the sand grains. Considerable study of the vaporization of metallic species has been reported in the literature, and the vapor transport properties of many metallic species have been determined.2'3 Many instances have been observed where the vaporization behavior could only be explained by the existence of a metallic species with a vapor pressure greater than the elemental metallic species. These species were identified or, in some cases, presumed to be carbonyls,4,5 hydroxides,6-9 or vaporous oxides.10-16 The diffusion of gases through porous aggregates has received considerable attention in the literature pertaining to catalysis, although primarily at low temperature, and more recently in the literature concerned with ore reduction.17-22 The following experiments were devised and carried out in order to determine the nature of the metallic species involved in the metal penetration phenomenon, and the effective diffusivities involved. EXPERIMENTAL APPROACH Steady-state diffusion was selected for experimental convenience. The experimental systems used, shown in Figs. 1 and 2, consisted of a porous aggregate specimen contained in an impermeable alumina tube held above, and just separate from a metal bath. The entire system was held at constant temperature and pressure in a furnace with a controlled oxygen partial pressure atmosphere. After a brief period of nonsteady state behavior, a steady flux of metal vapor through the porous aggregate will develop due to the concentration gradient of metallic vapor in the gas phase. The flux of metallic vapor from pressure may be neglected because there is no pressure gradient. There is no flux from convection because there is no net flow of gas within the metal-aggregate system, and thermal diffusion is negligible compared to the flux from ordinary diffusion. If the material being studied is allowed to vaporize until steady-state behavior is attained, the experimental results may be analyzed using Fick's First Law.

Jan 1, 1970

By J. Chipman, H. Towers, M. Paris

A simple radioactive tracer technique is used to measure the diffusion coefficient of calcium ion in molten slags. In a slag of 40 pct Ca0-40 pct Si0,-20 pct Al203, Dc " at 1450°C is 1.3x10-6 cm' sec-'. THE application of the principles of thermodynamics to steel and iron making problems has proved so fruitful that the kinetic approach has tended to be neglected. It seems probable that in some reactions the rate-determining step is the dif-fusivity of the reactants or of the products. But knowledge of the diffusion coefficients of the constituents of liquid slag and metal is singularly lacking. The present work was undertaken as a first step toward supplying such data for slags. Furthermore, any additional information on the physical properties of liquid slags might be expected to help in elucidating their structure. It is essentially a preliminary investigation, the course of which was determined more by the necessity of establishing a method than by the immediate intrinsic interest of the results. For example, the selection of calcium ion to be studied was dictated by the suitability of the isotope Ca45 in that it is a simple emitter with a long half-life. Of the other ions commonly encountered in slags, the isotopes of iron and manganese have relatively complex radiations as well as the normal disadvantage of requiring control of the oxygen potential of the atmosphere; Mg27 and Al29 have half-lives measured only in minutes; Si3' has a simple decay process but its half-life of 2.8 hr is too short for preliminary studies; the only useful oxygen isotope is the stable O18; and there remain only sulphur and phosphorus both of which have suitable isotopes but were rejected as being of less fundamental interest than calcium. Similarly a lime-alumina- silica slag was used in preference to calcium silicate primarily because of its low melting point and its capacity to form a glass on fairly rapid cooling. Literature Review Very few studies of diffusion in liquid silicate systems have been reported. In order to determine the origin of diopside inclusions in felspathic rocks, Bowen1 investigated the diffusion between diopside and various mixtures of albite and anorthite. Platinum crucibles were used with diopside, the heavier of the two liquids, forming the lower half of the cell and diffusion taking place against gravity. Change in concentration along the diffusion path was found by measuring the refractive index of the quenched glass. Nearly thirty years later McCallum and Barrett2 used essentially the same method to determine the diffusion coefficient of lime in lime-alumina-silica slags. In this case the interest was to find the rate-determining step in the process of slag attack on refractory materials. In an investigation of the kinetics of the sulphur reaction, Derge, Philbrook, and Goldman8 determined the diffusion coefficient of sulphur in a typical blast furnace slag by the simple procedure of melting a slag containing 2 pct S over an identical slag sulphur-free. They make no claim to a high degree of accuracy but suggest that D, is of the order of 10-6 cm2 sec-l. Other high temperature liquid diffusion studies have been concerned with metals. Holbrook, Furnas, and Joseph4 determined the diffusion coefficients of silicon, phosphorus, sulphur, manganese, and carbon in liquid iron by immersing a small carbon crucible containing pure iron-carbon alloy in a large vessel containing iron with a high concentration of the particular element. Their results were confirmed by Paschke and Hauttmann5 using a similar method. Diffusion coefficients in silicates in the glassy state have been studied by Johnson, Bristow, and Blau6 Both Na24 and Ca45 were used as tracers but only the

Jan 1, 1954

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By Heinrich Ries

In another place,* the writer has called attention to the modern methods of the laboratory investigation of clay, and it is desired here simply to discuss one branch of the subject, which, though of considerable importance, has heretofore received little attention in this country, viz., the rational analysis of clay. In order, however, the better to point out the bearings and advantages of this procedure, it is necessary to refer briefly to the ultimate analysis as well. The remarks in this paper refer only to the use of clay for the manufacture of clay-products. Pure clay or kaolin-f is extremely refractory, possesses little plasticity, and usually shrinks aud warps considerably in burning. Even the smallest proportion of impurities changes these properties, so that the kaolin exhibits variations in shrinkage, plasticity, tensile strength, fusibility, and often color when burned. The majority of nearly pure kaolins consist of kaolinite (A1,O2 2SiO,, 2H20), undecomposed feldspar, and quartz. The kaolinite generally forms the finest particles of the clay and is known as the clay-substance, while the rest of the clay-particles are collectively spoken of as sand. In the ordinary or ultimate analysis, the substances generally determined are silica, alumina, ferric oxide, lime, magnesia, alkalies and water. An analysis of this type simply regards the clay as a mixture of elements or oxides, but gives no clue as to the actual condition in which these substances exist, i.e., whether as silicates, oxides or carbonates, etc., a point which it is of the highest importance to know; for the individual components of the clay influence its properties not only according

Jan 1, 1899

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metaliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land the surface of which is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar" method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago, has become valuable agricultural land dotted here and there with growing towns. Frequent references. will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are equally applicable to all coal-mining states. Briefly stated, the question: is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1927

By Fred C. Bond

IN crushing and grinding the larger particles are more exposed to the work input. They absorb most of the work and protect the smaller neighboring particles from destructive contact with the crushing surfaces or grinding media. The importance of this exposure differential upon the reduction efficiency and product size distribution has long been recognized. Unfortunately, there has heretofore been no direct method of evaluating it, and such indirect methods as observing the slope of the plotted product size distribution line have been used as an indication. In this presentation the Third Theory of Comminution' has been used, together with the exponential formula for size distribution, to evaluate the ex- posure ratio and exposure constant and to illustrate examples of their utility in crushing and grinding applications. The exposure ratio Er varies from zero to unity. It is zero when the product particles are all of one size, and it is unity when the work input has been equally distributed among all particle sizes. It can readily be found from screen analyses plotted according to the Third Theory. The exposure constant K is derived from the reciprocal of the exposure ratio Er. It permits more consistent predictions of size distributions and evaluation of many factors concerned in size reduction operations. The Third Theory1 states that the specific work input required for size reduction is inversely proportional to the square root of the product size less the work required to form the feed. When P represents the diameter in microns which 80 pct of the product passes, F is the size 80 pct of the feed passes, Wi

Jan 1, 1958

By Edward B. Dismukes, Walter R. Dickson

Measurements of current efficiency at an iron anode during the electrolysis of FeO-CaO-SiO2 melts contained in an iron crucible indicate that compositions of high SiO5 content conduct current almost entirely by ionic mechanisms. Hozueuer, compositions of high metal oxide content give euidence for considerable nonionic conduction that can be attributed to p-type semicon-duction. Measurements of transference numbers in a Hittorf-type cell show that both calcium and iron ions are important contributors to ionic conduction. ELECTROCHEMICAL properties such as conductance, transference numbers. and oxidation or reduction at an electrode have been studied as means of delineating the structure of simple silicate melts that are related to the more complex slags encountered ir steelmaking processes.' Measurement of these properties has strengthened the concept that molten silicates are constituted of metal ions and of silicate networks. Typically, the magnitude of electrical conductivity and the extent of agreement with Faraday's law have given evidence for ionic structures, and transference numbers have shown cations to be the exclusive carriers of electrical charge. However, melts containing oxides of iron, FeO in particular, have been found to exhibit nonionic conduction of curx,ent. The work by Inouye, Tomlinson, and chipman' demonstrated semiconduction, presumably of the p-type, in molten wüstite. Simnad, Derge, and George3 and Dukelow and Derge,4 in studying the electrolysis of FeO-SiO2 and FeO-MnO-SiO2 melts, concluded that p-type semi-conduction occurs in these systems, although ionic conduction is generally favored by increased percentages of MnO or SIO2. Previous research on the electrochemistry of

Jan 1, 1962

By A. S. Learoyd

THE Anthracite Division, Bureau of Distribution, of the United States Fuel Administration, came into existence about Oct. 20, 1917. There had been no definite policy determined upon and the distribution had been carried out by the producers and distributors of this fuel as under normal conditions. The domestic sizes had been shipped from the beginning of the coal year on Apr. 1 in about their usual proportions to the various sections of the anthracite consuming territory of this country, which, in a general way, extended as far west as Nebraska and Montana, and in the south along the Atlantic seaboard to Florida. With the advent of cold weather, about the middle of November, acute shortages commenced to develop all over the northeastern section of the country, due to largely increased demand by the public in general, to enormously increased population in centers where industrial war activity was concentrated, and by the needs of the war industries themselves. Commencing with the early part of December, this demand was aggravated by extreme low temperatures and heavy snow; and the production decreased for the same reasons. From that date until the change in the weather, about the latter part of February, it was simply a question of getting coal into communities as emergencies occurred, to take care of individual cases. No definite plan of distribution could be followed. The coal mined between Apr. 1 and Nov. 1 had been distributed as mined and, therefore, only current production was available for distribution. The Anthracite Division, during this period, consisted of a Director, two assistants, together with an office force of seven or eight clerks and stenographers.

Jan 8, 1919

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By D. M. Deason, R. M. Chhatre, G. Y. Onoda

INTRODUCTION The treatment of colloidal suspensions is a subject of increasing interest in mining and benefication (1). Colloidal suspensions are not readily operated upon by mechanical and physical methods useful with coarse suspensions, such as filtration, thickening, and flotation. This is because colloids are strongly affected by interfacial and interparticle forces that may be large compared with, and resistant to, external forces. The degree and type of interactions between colloids can be modified by small additions of reagents such as coagulants, flocculants, dispersants, and immiscible liquids. These alterations in turn change the properties of the suspension and provide possible opportunities for transforming suspensions to a more favorable condition for a given processing operation. Phosphate slimes are an example of a colloidal system of interest today. In the mining and beneficiation of phosphate rock in Florida, slimes are a waste product. The phosphate ore (called matrix in the industry) is slurrified hydraulically and pumped to a beneficiation plant, where the -150 mesh material is removed by cycloning from the coarser phosphate rock and silica. The resulting -150 mesh slurry, called phosphate slime, is pumped to large impoundments. The solid content of the slime entering the impoundment is around four weight percent, and over 80% of the solids is less than one micron in size. The immediate problems with phosphate slime relate to their disposal (2, 3). The disposal problem is associated with the very large volumes and the poor dewatering characteristics of the slimes. To have sufficient impoundment volume, large earthen dams are built around the mined areas. The volume above ground level approaches and

Jan 1, 1980