Search Documents

By W. Crafts, J. L. Lamont

Secondary hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to thc secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at II00 F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader. Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to IIOOOF, but the mechanism of the process has received little consideration.

Jan 1, 1949

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969

Temperatures in the Open-hearth Furnace. By Robert B. Sosman. (Metals Tech. Aug. 1948, T.P. 2435) Steelmaking Direct Oxidation in the Basic Open Hearth Process. By E. R. Hughes and F. G. Norris. (Metals Tech., June 1948, T.P. 2380) With discussion Operation of Oxygen-enriched Open-hearth Furnaces. By J. S. Marsh. (Metals Tech., Aug. 1948, T. P. 2416) With discussion Role of Thermochemical Factors in Basic Open Hearth Production Rate. By T. E. Brower and B. M. Larsen. (Metals Tech., Oct. 1948, T.P. 2451) Structure, Segregation and Solidihcation of Semikilled Steel Ingots. By M. Tenenbaum. (Metals Tech., Sept. 1947, T.P. 2273) With discussion The Origin of Silicate Inclusions in Basic Electric-arc-furnace Steel of Higher Carbon Contents. By Axel Hultgren. (Metals Tech., Aug. 1948, T.P. 2418) A Method for Determining the Origin of Surface Defects in Rolled Steel Products. By C. L. Meyette and V. L. Elliott. (Metals Terh., June 1948, T.P. 2368) With discussion Gases in Steel The Sampling and Analysis of Steel for Hydrogen. By G. Derge, W. Peifer and J. H. Richards. (Metals Tech., June 1948, T.P. 2362) With discussion Apparatus for the Hot-extraction Analysis for Hydrogen in Steel. By C E. Sims and G. .I. Moore. (Metals Tech., June 1948, T.P. 2369) With discussion A Quantitative Experimental Investigation of the Hydrogen and Nitrogen Contents of Steel during Commercial Melting. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Feb. 1948, T.P. 2347) With discussion The Effect of Hydrogen on the Ductility of Cast Steels. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Sept. 1948, T.P. 2454) Sulphur in Ironmaking Kinetics of the Transfer of Sulphur across a Slag-metal Interface. By Lo-ching Chang and K. Goldman. (Metals Tech., June 1948, T.P. 2367) With discussion Some Correlations between Variables Affecting Sulphur in Blast Furnace Iron. By T. E. Brower and B. M. Larsen. (Metals Tech., Sept. 1948, T.P. 2465) Tracer Study of Sulphur in the Coke Oven. By S. E. Eaton, R. W. Hyde and 11. S. Old. (Metals Tech., Sept. 1948, T.P. 2453) Transformation of Austenite Anisothermal Formation of Bainite and Proeutectoid Constituents in Steels. By Leonard D. Jaffe. (Metals Tech., Dec. 1947, T.P. 2290) With discussion Austenite Transformation Above and Within the Martensite Range. By R. T. Howard, Jr. and M. Cohen. (Metals Tech., Oct. 1947, T.P. 2283) With discussion

Jan 1, 1949

HAVING previously described the metals to you, before I proceed any farther I do not wish to fail to tell you, as I promised to do in the first chapter on metals, what I have learned through experience concerning the semiminerals, although this may seem to you outside our proposed subject. Since these are not produced by Nature as all rock or all metal they are called semiminerals by speculative physicians. Many kinds of these are found; those that resemble rocks are earthy, very difficult to liquefy, and much more adapted for adorning paintings than for anything else. Those that liquefy with fire, like sulphur, antimony, marcasite, [22] calamine, zaffre, manganese, and others, resemble the metals almost like brothers. Some others are more watery so that they dissolve in water, although they are fairly dense, and are obtained and reduced to their, perfection by means of water. These are the salts, vitriol, rock alum, and saltpeter. To these, as a watery thing, belongs also quicksilver, as it is commonly called because of its motion. Although it appears. not only liquid, but very liquid, this is not at all similar in its effects to any of the above. Indeed, it retains its same being until its very form is consumed. Since the reasons for its effects are almost impossible to investigate, I do not intend to speak of them here or to enter now this maze of speculation, because I wish to make definitely clear to you what this quicksilver really is. Therefore, leaving aside opinions and disputes, I shall take only those of the said semiminerals that I know are useful. First we shall see the method by which the semiminerals can be found and then how they are to be extracted from their matrices. These, perhaps, have no less need of effort and industry than the metals since they are substances completely hidden in the rocks or in the earth. For this reason some of these that are sought are made use of by means of fusion after they have been mined from their mother mountains, and some others need to be disposed by a certain maturative corruption, now with moisture and coldness, now with dryness and heat, as with waters, rains, frosts, or long baking in the sun, with fire, or even with a strong reheating within themselves. Most of them can finally be brought to the desired end by means of solution with water and fire.

Jan 1, 1942

The German Kaiser is employing the keenest engineering talent of his own and allied empires in his attempt to defeat the world. American employers are paying engineers such attractive salaries that voluntary enlistments of high class technical men in the United-States Army, are below requirements. This deficiency is also probably due in part to the lack of proper information concerning the engineering branch of the service. Few civilians know that it is possible for them to perform in the Engineering Corps almost exactly the same kind of work as that in which they are now engaged. The best results in any organization are obtained only when the energy of every man in it is concentrated along the line for which he is best suited by natural ability, education, and training. It. is more important to have the right man in the right place in our Army, where lives of men are at stake, than it is in any business enterprise. The First Replace meat Regiment of Engineers was organized at Washington Barracks, D. C., on Dec. 14, 1917, with the express idea of accomplishing this. end. Its specific, purpose is to keep all engineering units of the Army at full enlistment strength during the period of this war. This regiment has not only the responsibility of finding men to fill depleted ranks, but it must also fit them to step into the work of trained, efficient and disciplined soldiers. The preliminary work of the recruit is first a thorough training in military drill, for the engineer soldier must be prepared to lay down his shovel and take up his rifle at any time. Infantry drills gradually give way to engineer work and more specific technical training. The. engineer soldiers must know how to tie knots and lashings, to build spar and truss bridges, to construct revetments, dig trenches, place wire entanglements, construct machine-gun emplacements, build pontoon bridges, and to construct roads: They must, also know the methods of demolition, sapping, and mining. Specialized training in lithography, zincography, surveying, mapping, photography, carpentry, blacksmithing, electricity, and machinery, are also given to those qualified for further training in any of these branches. Engineers are called upon to perform such a wide range of work that practically every man with any technical training or mechanical ability can find a place in this organization. Every male citizen in the United States who is physically fit, and between the ages of 18 and 21, and 31 and 40, is eligible to join the regiment by voluntary enlistment.

Jan 5, 1918

By E. J. Rapperport, J. P. Pemsler

We have made calculations to evaluate the sensitivity of atomic absorption as a technique to measure vapor pressure changes with temperature. Our conclusion, supported by the experimental findings presented in this work, is that the ultimate sensitivity of the technique is well below lo-&apos; Torr. This magnitude of vapor pressure sensitivity makes the method extremely attractive for thermodynamic studies. Atomic absorption techniques have been used previously in this connection by Scatchard and Boyd&apos; and by vidale2 with a much lower sensitivity reported. Scatchard and Boyd&apos;s work measured cadmium pressure over Ag-Cd alloys in the range 0.02 to 0.3 Torr, and Vidale estimated that sensitivities of only 10"5 to 10"6 Torr are to be expected. Atomic absorption appears to be particularly well-suited to thermodynamic studies for several reasons: A) It is extremely sensitive; our experiments indicate an ability to measure vapor pressure changes of 10"9 Torr. B) It is highly selective; there is seldom interference among the resonant wavelengths of the various species. C) It may be performed in an absorption cell under static conditions. This alleviates such problems as surface impoverishment of alloys, attainment of equilibrium, and temperature measurement and control. D) Simultaneous, or near-simultaneous, vapor pressure measurements may be made for several elements in a given system. Experimental. The physical basis of the technique is the highly selective absorption of particular wavelengths by specific atomic species. In most atomic absorption work the element of interest is incorporated into a hollow cathode lamp to provide a characteristic spectral source of high intensity. The spectra lines characteristic of the element in the cathode are attenuated by atoms of that element in the radiation path. Radiation from silver or cadmium hollow cathode lamps was directed along a path containing a 10-cm evacuated silica cell. The cell was positioned within a silica windowed furnace and contained silver, cadmium, or an Ag-Cd alloy. As the furnace temperature was elevated, the number of atoms of the absorbing element in the vapor phase within the cell rose, and the resonant radiation was increasingly absorbed. Intensities were measured by passing the radiation through a Techtron Model AA-4 one-half meter grating atomic absorption spectrometer equipped with a photo-multiplier detector. In order to minimize instabilities in the source, the hollow cathodes were allowed to warm up for several hours and were run at only 2 5 to 30 pct of their maximum rated amperage. In addition the attenuated beam was monitored before and after each reading. The attenuation of resonant wavelengths may be related to vapor pressure by the following relationships.

Jan 1, 1969

By David V. Ragone, Richard E. Balzhiser

The liquidus uranium concentration in the U-Bi system is given by the following expression for the temperature range 400° to 800°C: No break was observed in the curve over this temperature range. The partial molar enthalpy change for uranium in the liquidus reaction, UBi2— U + 2Bi, was found to equal 12,300 cal per g mole. Copper produced a continuous decrease in the liguihs uranium concentration at 600°C. The presence of copper in the solvent was observed to affect the uranium activity coefficient according to the following expression: duced no change in the liquidus combosition below 0.6 at. pct Pd. Higher palladium concentrations sharply depressed the uranium concentration. SOLUTE behavior in molten alloys has been shown to be strongly influenced by the presence of additional species. Much attention has been given to such phenomena in iron-base systems where a number of alloying elements and/or impurities are likely to be present in small but significant quantities. Frequently, the interaction of these solutes has altered their thermodynamic behavior to the extent that reaction equilibra are appreciably influenced. Consequently, much of the information available for binary behavior must be reevaluated when additional components are likely to be present. Similar interactions can be expected to occur in bismuth-base solvents. Interest in the use of bismuth solutions of uranium as reactor fuels has stimulated investigators to explore the effect of various elements on the liquidus uranium concentration. Criticality requirements necessitate close control of the uranium concentration which, at the anticipated operating temperature of 500°C, approaches saturation. Consequently, elements which suppress the liquidus concentration could produce serious reactivity problems. Since the fuel solution is cer- tain to contain additives, such as magnesium and zirconium, for corrosion inhibition as well as small concentrations of fission products and corrosion products, a better understanding of the possible interaction phenomena is mandatory. This need stimulated experimental programs at the Brookhaven National Laboratory and elsewhere to determine precisely the liquidus uranium concentration in the bismuth-rich portion of several ternary systems. Early experimental efforts were directed toward an accurate dcmtermination of the U-Bi liquidus over the temperature range from 300&apos; to 800°c. As shown in Fig. 1, the results to date exhibit considerable scatter. The investigations of Bareis,&apos; Teitel,2 Greenwood,3 and Cotterill and hon4 agreed well below 700°c. Greenwood and Teitel extended their studies to higher temperatures but failed to concur in their results. A more recent study by Schweitzer and weekss at Brookhaven National Laboratory between 300&apos; and 725°c, produced values 15 pct lower

Jan 1, 1962

By J. F. Wilson

Steady-state flow theory, previously applied to displacements with two mobile phases, is extended to cover down-structure flow involving three mobile phases: oil, gas and water. When used with normal reservoir fluid properties, the theory predicts the existence of four distinct flow regimes and the conditions under which each regime exists. The predicted behavior is verified by a parallel-plate model study. INTRODUCTION Special problems exist when a water flood is contemplated in a dipping reservoir having a substantial gas cap. Normally, the gas-cap region is one of very low oil saturation. If oil is moved into the gas cap during the flood, a loss in recovery results. Efficient recovery of the oil underlying the gas is therefore difficult. In two reported field water floods, injection into the gas cap has been used to solve these problems. At the West Norfolk Garr Sand Unit, injection into the upstructure region of the reservoir was made for the stated purpose of filling up the gas cap with water.&apos; The purpose in the Sholem Alechem Fault Block "A" Sims Sand Unit was to form a continuous water barrier between the gas cap and oil band.&apos; A laboratory model study preceded this flood and was described in the same publication. Both of these gas-cap water injections gave satisfactory results, but the published data are insufficient to allow generalizing to other field conditions. The present investigation was also undertaken to obtain results for a specific field problem. However, these results will be shown to be in agreement with an extension of the Dietz3-5 mathematical model to three-phase flowing systems. The agreement between the theory and the model studies indicates that the mathematical model can be used to describe completely the flowing system under some conditions, and to indicate the general type of flow to be expected under all conditions. FLOW THEORY The Dietz equations for two-phase flow are derived "&apos; for the case of constant-velocity linear flow in a homog- eneous porous medium. The transition zone between the fluids is assumed to be of negligible extent so that the displaced and displacing fluids are separated by a sharply defined interface, as illustrated in Fig. 1. The density and mobility of the displacing fluid are constant over the region behind the interface, and the same properties of the displaced fluid are constant over the region ahead of the interface. To extend the Dietz equations to three-phase systems, we postulate the flowing system shown in Fig. 2 and determine the conditions under which it can exist. The

By H. M. Chance, T. M. Chance

The term &apos;Llow-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as.1 1/2 per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. , In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low-sul. fur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, with few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 1/2 per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous districts, it has been necessary to turn to the areas of higher sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.—Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout the coal but is usually confined to high-sulfur benches in the bed or to concentrations on the cleavage planes of the coal. Hence, by graded crushing and sizing it is frequently possible to at once reclaim those portions of the coal bed containing coal that is relatively free from pyrite.

Jan 1, 1920

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By R. S. Shoemaker, F. W. McQuiston

RECOVERY METHODS AS RELATED TO PROPERTIES OF SILVER ORES The earliest metallurgical process for treating silver ores was amalgamation with mercury which was in use in the early 1500&apos;s. Closely following was the development of the Patio process for treating ores at Pachuca, Mexico. Silver often occurs as the native metal and in deposits associated with other metals such as gold, copper, lead and zinc. Principal silver minerals include compounds of sulfur, antimony, arsenic, and copper. Silver chloride, and argentiferous galena are also prime sources. Native silver and the chloride characterize the oxide zone of most deposits. Native silver can be concentrated, amalgamated, or cyanided. Silver chloride rapidly dissolves in cyanide without oxygen. Oxidized silver ores containing the higher oxides of manganese are generally refractory to metallurgical treatment. A refractory compound of manganese and silver is formed, probably a manganite , which is insoluble in cyanide solutions. Argentite is the predominant silver mineral. Other important economic minerals are native silver, argentiferous galena, cerargyrite, pyrargyrite and tetrahedrite. Argentite dissolves slowly, the reaction being reversible requires an excess of cyanide. Argentite with disseminated fine grained gold occurring in quartz veins with minor amounts of chalcopyrite and galena may be cyanided directly after grinding, with high silver and gold recoveries. The flowsheet adapted to this type of ore is the Minas de San Luis, Tayoltita cyanide plant, which treats a high grade argentite silver ore containing gold. It is a standard cyanidation circuit but employs long periods of agitation contact for the high silver sulfide content ore. Lead-zinc base metal semi-oxidized- complex ores in pipes and chimneys are replacement deposits in limestone at El Mochito Mine, Honduras. Mineralization comprises galena, cerussite, anglesite, sphalerite, calamine, and smithsonite. The silver content of about 16 ounces occurs as native silver globs, wire and the mineral argentite. After flotation of lead and zinc concentrates, the tailings are cyanided for gold and silver recovery. The great Huelva pyritic copper deposits of Spain carry a little gold and silver. At Cerro Colorado, these metals were concentrated above the chalcocite zone into the so-labeled Mgossanu. This material with a content of 0.08-0.09 oz Au and 1.50 oz Ag per ton is amenable to cyanidation. See Cerro Colorado flowsheet. In southern Hidalgo, about 60 miles north of Mexico City, are the great silver--gold veins of one of the foremost silver mining districts of the world. Real del Monte, Pachuca. The mineralized area consists of flow rocks and intrusives. The oxidized ores carry pyrites with oxides of iron and manganese and other minerals, silver and gold. The first zone contains

Jan 1, 1975

By H. E. Dunn, C. M. Cosman, J. H. Brennan

Up to the beginning of World War I, the American ferro-alloy industry was in its infancy and largely dependent on Europe. During that War, capacity was over expanded. Later recovery and commercial and scientific development have resulted in an industry which in 1957 produced 1.8 million tons of ferro-alloys. THE ferro-alloy industry is today an important element of the industrial structure of the United States. Its output is valued at almost half a billion dollars annually and its products are basic not only to National defense but also to the peacetime standard of living. This has not always been so. The ferro-alloy industry from late in the last century has grown from small beginnings, nurtured by the demand for stronger, tougher materials; by the search for steels capable of absorbing severe impact loads and resisting corrosive media and high temperatures; and also by the need for electrical and electronic specialties. Conversely, the ferro-alloy industry has grown because it developed improved steels and alloys by extensive research, and because it was able to show to steel makers the advantages accruing from the more extensive and the more economical use of alloying elements. The industry has grown in scope from producing a few grades of ferro-alloys of the more common metals-manganese, chromium, vanadium, silicon, titanium, tungsten, and molybdenum-until there are today some 150 compositions of ferro-alloys available to the steel maker, including such elements as columbium, zirconium, and boron. In 1912 the industry produced 360,000 tons of alloys valued at about $12,000,000, while 1957 production figures show an output of 1.8 million tons worth $440,000,000. In the United States, the history of an industry is largely the history of the companies making up this industry; hence, this paper will briefly trace the development of the most important ferro-alloy-producing companies. Quite varied have been the reasons that caused the different companies to move into the ferro-alloy field; the Willson Aluminum Co., seeking methods of producing aluminum, succeeded with the production of calcium carbide, and their developing electric furnace skills led them to the production of ferro-silicon and ferrochromium alloys. Willson was the predecessor of the Electro Metallurgical Co. of Union Carbide. Two Pittsburgh undertakers, interested in vanadium as an alloying agent for steel, set about to find a mine and, ranging as far as Peru, fathered American Vanadium Co., the predecessor of Vanadium Corp. of America Experiments of the

Jan 1, 1961

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952

By W. H. Ashby, R. W. Cassingham, C. R. Blomberg, J. B. Justins

The Brookhaven field is one of several Basal Tuscaloosa reservoirs located in south-central Mississippi. It is a standstone reservoir, of erratic deposition and with several faults, having an approximate subsea depth of 9,800 ft. A large variation in permeability exists with a weighted average being 256 md. Estimated average interstitial water saturation is 45 per cent. The undersaturated reservoir fluid exhibits marked differences in physical properties with measured saturation pressures ranging from 733 to 2,255 psi. Early rapid decline in reservoir pressure caused the operating interests to unitize the field and initiate a program of pressure maintenance by gas injection. At the time gas injection was commenced, the reservoir pressure had fallen to nearly half of the original pressure with only 4.5 Per cent of the original oil in place produced. The reservoir pressure has since been maintained at approximately 2,750 psig, and cumulative production to date is 17 per cent of original oil in place. An analysis of field performance during gas injection is presented in detail. The program of pressure maintenance by gas injection is considered to be a success, since the expected ultimate recovery has been increased and the current production rate is in excess of 2 per cent of original oil in place per year. Performance has been better, anticipated ultimate recovery is larger, and total production costs are lower than for a similar Basal Tuscaloosa reservoir nearby, even though that field appears to have a more effective natural water drive. INTRODUCTION The history of the Brookhaven Unit is a testimonial for unitization and for the application of engineering techniques in the operation of an oil field. The operating and royalty interests in this field have mutually benefited from their early recognition of the need for unitization and pressure maintenance and from the forthright manner in which these were accomplished. The tangible benefits accruing to the participants in the Unit are: (1) income from gasoline plant products, (2) reduced lifting and operating costs from those of competitive operation, (3) maintenance of high levels of current income by mitigation of the inevitable decline in production rates inherent to natural depletion, (4) an increase in ultimate recovery of about 40 per cent over natural depletion operations. This paper should properly be considered a progress report; however, the performance of the field after five years of pressure maintenance clearly indicates that the ultimate success of the project is assured. LOCATION AND GEOLOGY The Brookhaven field is located in south-central Mississippi, about six miles from the town of Brookhaven. Production at Brookhaven

Jan 1, 1955

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm&apos;s law and d&apos;Arcy&apos;s law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm&apos;s law and d&apos;Arcy&apos;s law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By I. Fatt

This paper proposes the network of tubes as a model more closely representing real porous media than does the bundle of tubes. Capillary pressure curves are derived from network models and pore size distributions are calculated from these curves. In this way is shown the difference between the true and calculated pore size distributions when the capillary pressure curve is used to obtain pore size distribution for porous media. INTRODUCTION Despite the technological importance of the laws governing flow through porous media, many of these laws have not yet been clearly formulated. This is especially true of the laws governing multiphase flow. The static properties, such as the capillary pressure curve, are also not at present interpretable correctly in terms of the pore size distribution and other structural properties of porous media. In the absence of any well founded theoretical description of fluid flow through porous media, many empirical descriptions have been proposed. In addition to the strictly empirical flow equa- tions, some equations have been developed rigorously from simple geometrical models of the pore spaces. These equations are only as valid as is the model used in their development. The two models used in the past, the sphere pack and the bundle of tubes, have been too simple, and as a result, the equations derived from them have failed to predict the observed properties. Agreement between theory and observation has been achieved for these models by inserting parameters of doubtful physical significance. The work to be reported here was undertaken in the belief that the study of a model more closely resembling most real porous media than does the sphere pack or bundle of tubes would yield useful information concerning the structure of real porous media and the relation between structure and flow properties. There was no intention of developing any calculational procedures, as for example calculating relative permeability from capillary pressure data. The objective of the study was instead to develop a better qualitative understanding of the relation between the various measurable properties of porous media. The model chosen for study is the network of tubes in which each tube represents a pore space in the porous medium. Microscopic observations leave no doubt that sandstones and clastic carbonates are three-dimensional irregular networks of irregularly shaped pores. The irregularity of these structures makes any accurate theoretical study of their properties impossible. Results from an oversimplified model such as the bundle of tubes are worthless when applied to real systerns. The sphere pack model, on the other hand, not

Jan 1, 1957

By Carl Pierce

The writer of this article has not attempted to write a technical paper; on the contrary, he has tried to express in "steel-plant English," for steel men, a viewpoint drawn from his practice and experience. It is not his thought that it shall be taken as the "last word" in the making of this class of steel, or that good rimming steel cannot be made by any other practice. The paper was written to serve as the basis of a discussion from which it is hoped much benefit may be derived. The paper deals only with rimming steel made by the open-hearth process, and with the lower carbon steels, such as sheet and tin bar, rivet stock, skelp, etc., although good rimming steel as high as 40 to 50 carbon can be made by having good open slags and giving proper attention to working and tapping temperatures. Definition of Rimmed Steel Rimmed steel is sometimes called open or effervescing steel to differentiate it from killed or partly killed steel. It is steel made by a process which permits the free escape of gases from the metal in the molds. In passing up through the metal, the gases keep it in a rolling action from the walls of the mold inward. The top of the ingot rims in as the metal chills and the walls of the ingot get thicker, the center part remaining fluid until it reaches a pasty condition when it is covered with a cast-iron cap. The Charge In making up a charge for rimming steel, clean stock of a known composition must be selected, special attention being given to the analysis of the materials. The silicon in good rimming steel must be eliminated to a trace, therefore it is advisable to have a uniform amount going into the charge. Too much silicon gives a raw melting heat from which rimming steel is unlikely to result. For this reason a charge containing not to exceed 40 per cent. pig iron and 60 per cent. scrap, with no iron ore, is preferred to the Monell type of charge in which as high as 65 to 70 per cent. pig iron is used with a proportional amount of iron ore for the removal of the excess silicon and carbon. The silicon content of pig iron varies so much from day to day in the average blast-furnace practice that there is danger of getting too much of this element in the latter mixture when

Jan 1, 1926

By J. A. Herbst, G. A. Grandy, T. S. Mika, D. W. Fuerstenau, G. D. Gumtz

As a basis for interpretation of grinding behavior, the discretized batch grinding model is briefly presented and described, with solutions of the resultant equations for linear systems. Techniques for obtaining relevant experimental data are discussed for first order grinding systems, with methods for estimating other systems1 parameters from these data. Computer methods are described for conducting a sensitivity analysis which can be used to obtain an improved estimate of the system parameters. Examples of the use of the computer in conjunction with the grinding model for the simulation of batch grinding, locked-cycle grinding, and closed-circuit grinding are presented.

Jan 1, 1969

By D. H. Thompson, A. W. Tracy

Season-cracking is a type of failure of brass that results from the simultaneous effect of stress and certain corrodants. The object of this paper is to present data that will aid in a more complete understanding of the mechanism of season-cracking and related phenomena. Results presented show that certain high copper alloys are susceptible to season-cracking or stress-corrosion cracking, and possible explanations are discussed. Starting at least as far back as 1906, many papers have been devoted to this subject but the symposium1 held in Philadelphia in 1944 is the richest source of information. In order to study season-cracking, several of the many variables were held constant so as to learn the effects of others. Season-cracking is generally understood to refer to the corrosion cracking of brass having internal stresses;²,³ it is a special case of the general stress-corrosion cracking. Inasmuch as applied stresses are more readily produced and controlled, they were used exclusively in this research and the resulting phenomenon must he called stress-corrosion cracking.²,³ Only constant tensile stresses were used. The agents believed to be most frequently responsible for season-cracking are ammonia. amines and compounds containing then]. Both moisture and oxygen also appear to he necessary. Therefore, an atmosphere containing ammonia, water-vapor and air was selected for these tests. Briefly, the work consisted of exposing sheet metal specimens, having a reduced section ¼ by 0.050 in., of copper-base alloys to the effect of static tensile stresses between 5,000 and 20,000 psi and simultaneous contact with a. continuously renewed atmosphere containing 80 pct air, 16 pct ammonia and 4 pct water vapor at 35°C. The gas mixture and the speci- mens were maintained above the dew-point. The time-to-failure in minutes was the primary measure of results. In order to limit the experiment to finite time, it was considered that a specimen which had neither failed nor undergone microscopically detectable cracking in 40,000 min. (4 weeks) while under a stress of 10,000 psi or more could be considered immune to cracking. This is merely a convenient limit and is not to be considered proof of immunity. Supplementary tests in the absence of stress using weight loss or microscopical appearance as measures of attack were made. Apparatus The apparatus used in this research is shown in Fig 1. To facilitate the description it may conveniently be divided into six parts: stress-producing units, test chamber, gas train, electrical controls, timers and gas analysis device. A stress-producing unit is shown in an exploded view at the left in Fig 2. At the right is an assembled unit with a specimen in place in the lower portion; it is this part that remains in the ammonia atmosphere during a test. The upper part contains a spring, a central threaded rod, a large nut and necessary washers, pins, and so forth. Stress is produced in the specimen by screwing down the top nut against the spring, thus putting a tensile load on the central rod and so on the specimen. The wrench that turns the nut by extending through the upper cap, is seen at the upper right of the figure. The magnitude of the load is gauged by measuring from the pin that extends through the side of the tube, to a fixed point on the large flange. Measurement is made with a vernier beam caliper, shown at the right of the figure. The necessary spring compression to give a desired stress is calculated from the calibration curve of the spring and the dimensions of the specimen. The test chamber, center Fig 1, consists of a thermally insulated steel box 32 in. long by 10 in. high by 7 in. wide. A horizontal baffle reaching nearly to each end divides the chamber equally. Below this baffle are inlets for air and ammonia, a heating coil and a fan. Thus the gases are warmed and mixed in the lower level and flow past the specimens in the upper level. A thermo-regulator and thermometer project into the upper space. The top is pierced by 12 ports flanked by 3/8 in. threaded studs. A test starts when a port is opened and a unit containing a stressed specimen is thrust through it and bolted down against a neoprene gasket. The test chamber is held at 35°C. The gas train, right rear Fig 1, carries ammonia and air continuously to the test chamber. Tank ammonia passes through two reducing valves, a needle valve, a flow meter and into the test chamber. The air from either the plant compressor or a small laboratory compressor passes through wool towers and flow controls to the flow-meter. It then bubbles through water at 34°C and through a heated line to the test chamber. Electrical controls, left rear, Fig 1, provide rectifiers and mercury relays for the test-chamber and humidifier-heating-control circuits and outlets for

Jan 1, 1950