Search Documents

By Robert Maddin

crystal prior to, polishing in order to eliminate coring. This treatment may be accomplished by wrapping the single crystal tightly in very thin, dead soft, brass foil and annealing in the presence of air for 20 hr at 800°C. Since the wrapping encircles the sptcimen three to four times, only a very slight amount of oxidation occurs on the specimen surface. On unwrapping one of these cylindrical single crystals. in. in diam by ro in. long (72.75 pct cu, 27.23 pct Zn, 0.01 pct P11, 0.01 pct re), mall light-gray depnrrits in the form of circular arcs werenoted on the part nf the foil which had been in contact with the single crystal, Fig r. (By superim- approximatetl). These deposits, which, from their color, suggest the appearance of sublimated zinc, were found to coincide roughly with a set of octahedral planes nearly perpendicular to the rod axis. The pattern shorn in the figure held no relation to the profle of the sample since the markin~s on the crystal More annealing werc attributed to traces of cube planes. It seems very likely that the deposits were formed by sutllimation of zinc diffusing from octahrdral planes since diffusian would Eogically take place along planes of maximum atomic spacing. However, it is difficult to understand why a continuous sublimation of zinc should occur from a single crystat in contact with a wrapping roil OF the same composition, and why diffusion would take place along specific octahedral planes and in a regular pattern.

Jan 1, 1949

By Charles W. Schwartz, Subash Kolluru

INTRODUCTION Creep of rock in situ, like most rock mass behavior, will be largely governed by the behavior of the natural discontinuities -- bedding planes, faults, and joints, in particular, Several past studies have investigated various aspects of the time-dependent deformation of rock discontinuities; examples include Amadei and Curran (1980), Engelder and Scholz (1976), Johnson (1975), Kaiser and Morgenstern (1979), Solberg et al. (1978), and Wawersik (1974). These studies have provided much insight into the general phenomenon, but they have also produced some inconsistent conclusions and left many unanswered questions. This paper will attempt to shed some light on one of these questions: What is the influence of stress level on the creep of unfilled rock joints? The discussion will follow a two-part approach to the problem: (1) laboratory creep experiments on small scale jointed specimens, (2) a simple theoretical mechanism to explain, at least in qualitative terms, some of the results from the experimental program. EXPERIMENTAL PROGRAM Uniaxial creep tests were conducted on intact and jointed samples of a specially formulated gypsum plaster "synthetic rock." Synthetic rock materials have several advantages over natural rock for long-term creep testing: (a) higher creep rates, (b) lower strength and therefore lower loading requirements, (c) simpler specimen preparation, and (d) more controlled and consistent properties. Gypsum based plasters have been used previously in studies of short-term strength and deformability of jointed samples (Patton, 1966; Einstein and Hirschfeld, 1973). Furthermore, Williams and Elizzi (1977) demonstrated that natural gypsum, at least, creeps in a manner similar to that of most other creep-susceptible natural rocks.

Jan 1, 1982

By H. l. Burghoff

THE presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Egleston1 reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the. mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn).

Jan 1, 1937

By P. de Vitry, Willis P. Mould

The wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually pis or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired anale. The usual drive is by a 10-hp. motor through a gear reducer, on which are Insti- two grooved sheaves, One of which is keyed and the other free running On the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1948

By P. de Vitry, Willis P. Mould

The wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually pis or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired anale. The usual drive is by a 10-hp. motor through a gear reducer, on which are Insti- two grooved sheaves, One of which is keyed and the other free running On the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1948

By P. de Vitry, Willis P. Mould

THE wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. [ ] Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually 3/16 or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired angle. The usual drive is by a 10-hp. motor through a gear reducer, on which are mounted two grooved sheaves, one of which is keyed and the other free running on the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1946

By M. H. Rana, W. D. Bullock

A basic requirement in any geomechanical investigation is the establishment of the state of stress in the rock mass. So far, qualitative determinations have been more readily obtained than quantitative ones. This is due to the fact that in order to define stress magnitudes in a rock mass it is necessary to make various basic assumptions about the physical properties and characteristics of the rock itself. The assumptions are generally that the rock is an isotropic, homogeneous solid which will behave elastically under various conditions of applied load. These assumptions are not valid. Due to the foregoing factors, the present investigation was confined to a consideration of stress directions only. Within recent years, two methods of determining stress orientations in geologic materials have been used and have received some publicity in the technical press. These are the techniques of photoelasticity and petrofabrics. The technique of using reflected polarized light for observing strains on the faces of rock samples has been described by Emery.1,2 With this technique it is possible to measure relative strains in relaxation. Absolute strain magnitudes are not attainable without the use of questionable assumptions. However, directions of strains (and thus, stresses) can be determined accurately on a point basis or on a statistical basis over the complete area of the strain gage being used. Petrofabrics, according to Friedman,3 an important geological discipline which can provide knowledge on the state of stress associated with naturally deformed rocks. Even though textural and structural features span at least 15 orders of magnitude, from crystal lattices

Jan 1, 1972

By R. W. Kraft

The normal Mg-Mg,Sn eutectic is a classic example of a Chinese script eutectic. When the alloy is unidirectionally solidified, a much simpler topo-logical arrangement of the phase particles can be produced although individual grains still usually consist of two or more interpenetrating lamellar systerns. Specimens from unidirectionally solidified ingots were analyzed metallographicall~ and crys-tallographically, and it was found that the interfaces between the lamellae had a common crystallograPhic character describable by: Lamellar interfaces II {220}Mg2Sn 1) {1011}Mg Arguments are presented to explain why this particular orientation relationship tends to occur and it is shown that this criterion can be nearly satisfied simultaneously on up to four different lamellar systerns between two interpenetrating single crystals. Finally, on the basis of this work ad other similar work which has previously been done on Al-CuAl2 eutectics, a general principle pertaining to low-energy interfaces between two crystalline Phases is proposed. WITHIN the past few years several investigators1-4 have demonstrated that the microstructures of many eutectic alloys can be significantly altered by uni- directional solidification. If appropriate control is exercised over the purity of the alloy, the growth rate, and the thermal gradient during unidirectional solidification, ingots can be made in which the phase particles are aligned predominantly parallel to one another throughout substantial portions of the ingot. The present author has also shown for at least one of the alloys that the parallel lamellae tend to assume a unique crystallographic relationship during

Jan 1, 1963

By J. W. Downey, S. T. Zegler

A study has been made of the occurrence of Phases having the Cr30-type structure in ternary alloys having the general composition where B cept for iron and copper all the B components are known to form binary compounds having the type structure. The occurrence of the struc-ture type in the ternary alloys was investigated using optical and X-ray metallography. The results indicate that iron can replace virtually none of the cobalt in at 900°C, but substitutes for nickel in up to the approximate composition tually insoluble in V3Ni and 2) and exhibit complete solubility. At 100 nickel can be substituted for cobalt in VSCo up to the composition solubility; and 3) in the system , two solid solutions having the type structure occur. At the same temperature, 1000°C, V3Si exhibits limited solubility for V3Co but is completely mis-cible with V3Ga. Lattice parameters have been determined for all the binary and ternary phases. The solid solutions are discussed in terms of the atomic size and electronic factors which are thought to influence the occurrence of Cr30-type phases. The binary compounds V3Co and V3Ni were found to form peritectoidally from o phases and a vanadium, the former compound at a temperature between 1000" and 1050°C, the latter between 800°and 900°C. The substitutions of nickel and rhodium for cobalt in V3Co were determined not to raise the superconducting transition of VSCo to a temperature as high as 2°K. The occurrence and stability of binary intermediate phases having the Cr30- or A15-type structure (space group o;, Pm3n) have been discussed in several recent papers . Vanadium forms the struc -ture at or near V3B stoichiometry with all the mem -bers of the cobalt and nickel groups in the periodic table and also with Au, Ga, Si, Ge, Sn, P, As, and Sb. This paper describes a survey of the occurrence of the CrsO-type structure in ternary alloys having the general composition V3(B, B') where B and B' are Fe, Co, Ni, Cu, Rh, Ir, Si, and Ga. The purpose of the survey was to clarify the connection between the position of the B partner in the periodic table and its CrsO-type phase-forming tenden~y.~,~ The survey is part of a broader program concerned with the influence of B-partner substitutions on the superconducting transition temperatures of CrsO-type compounds. The transition temperatures, Tc, of some of the ternary Cr,O-type phases found in the survey are also discussed in this paper. EXPERIMENTAL PROCEDURE The alloys were prepared by arc-melting in an A-He atmosphere and were in the form of buttons, weighing approximately 3 g. The metals used in their preparation were received from commercial sources and were in all cases 99.9+ pct pure. The vanadium was spectrochemically pure except for 800 ppm of Si, 200 ppm of Fe, and 200 ppm of Al. For study of each pseudobinary system at least seven alloys were prepared having the general compositions case of alloys containing gallium, melting losses were small, usually less than 0.3 pct of the total weight of the metals charged for melting. Melting losses were somewhat greater for gallium alloys, ranging in general from 0.9 to 5.0 pct. Ternary V-Si-Ga alloys were chemically analyzed and the results are given in Table I. The analyses show most alloys to be within 2 at. pct of the intended composition. Throughout the balance of the paper the intended compositions are used in discussing the alloys. The cast buttons were annealed within evacuated quartz capsules for times ranging from 3 to 6 weeks at temperatures between 800" and 1000°C and water-quenched. The phases present in the annealed and quenched alloys were identified by optical and X-ray metallography. X-ray diffraction photograms were made with powders prepared from the bulk specimens, by the use of a 114.6-mm-diam powder camera with copper irradiation. The lattice parameter of CrsO-type phases and their standard errors

Jan 1, 1963

By C. F. Smart

THE heat treatment of the bronze composed of 88 per cent. copper, 10 per cent. tin, and 2 per cent. zinc, has been investigated by H. S. and J. G. S. Primrose,1 and also by the U. S. Bureau of Standards.2 The results obtained by H. S. and J. G. S. Primrose on dry-sand castings subjected to reheating followed by air cooling, or by quenching in water, are shown in Figs. 1 and 2. The values for tensile strength have been FIG. 1.-EFFECT OF QUENCHING ON DRY SAND CASTINGS (H. S. AND J. G. S. PRIMROSE.) converted from tons per square inch to pounds per square inch. Figs. 3and 4, have been plotted from values obtained by the Bureau of Standards on material of the same composition and treatment. Both investigations show that the ductility of the cast bronze is improved by heating to 700° C. and cooling in air, the strength not being impaired by this treatment. They are not in agreement, however, as to the effect of quenching, Messrs. Primrose reporting a decrease, and the Bureau of Standards an increase, in both strength and ductility when the cast bronze is heated to 600° or 700° C. and quenched.

Jan 9, 1919

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By Strathmore R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." 1 Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an al- most identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds."' In the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter.

Jan 9, 1959

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler's saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By James F. Kemp

(San Francisco Meeting, September, 1915) THE iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by. these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. PREVIOUS WORK In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the tine Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 9, 1915

By R. C. Hall

DEVELOPED to grow single crystals of alloys of high hardness and high melting points is a simple but effective apparatus described in this note. Growth from the melt, that is, by the Bridgman technique, hay be applied to metals or alloys which are physically hard as long as no phase transformation occurs on cooling to room temperature. The present apparatus was employed to grow single crystals of the ferromagnetic AI-Fe alloys above 1 wt pct Al and the Si-Fe alloys above 3 wt pct Si. Single Crystal Growth In a simple form, the method for growth of single crystals from the melt requires a molten metal charge in a pointed crucible which is slowly low-ered through a heated zone into a colder zone. Solidification starts at the bottom point and continues up the charge as the crucible is lowered through the heated zone. If a single crystal nucleates at the bottom, one crystal may grow throughout the charge under ideal conditions of slow growth.4,5 The presently developed method of growth was designed so that the chances that more than one crystal would grow were small. The single crystals were growth by the apparatus illustrated in Fig. 1. The charge was in the form

Jan 1, 1958

By H. E. Powell, A. A. Cochran, R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide, each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are adsorbed on the mineral surfaces. As the pH of the xanthate solution increased from 5.6 to 11.0, the amount of cuprous ethyl xanthate on powdered sphalerite surfaces decreased and the amount of ethyl dixanthogen first increased and then decreased. It is generally accepted that the collector potassium ethyl xanthate will not float the mineral sphalerite (ZnS). However, Gaudin1 showed that sphalerite readily floats if activated with certain metal cations before exposure to the xanthate. Copper sulfate (CuSO4) was found to be the best activator for sphalerite. The over-all flotation reagent reaction, as given by Gaudin,3 is as follows: While this is the over-all reaction, the exact mechanism of the reaction and the intermediate compounds that may be formed are not yet known with certainty. Important work has been done in Russia by Plaksin

Jan 1, 1968

By C. Jackson, J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a 2-min repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaing a limited maximum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1978

The Honor Roll includes the names of all members of the Institute whom we know to be on active military duty at the date of its compilation, February 7, 1918. We are aware that there are many others of whose activities we have not been informed, and we shall be grateful for information as to any such omissions from the Roll. 1. MEMBERS ON ACTIVE MILITARY SERVICE Mail addressed to members on the first division of the Roll and sent to the office of the Institute Will be forwarded according to the best of our knowledge at the time. AARONS, J. BOYD, Capt., 4th Reinforcements, 11th Infantry, Australian Imperial Force. '05 ADAMS, HENRY, Capt Asst. to Dept. Engr., Northeastern Department. '02 AGNEW, FRANK VANS '04 ARBE, FREDERICK R., Capt 33d Engineers. '97 ALDER, ALFRED Engineers' Reserve Corps. '17 ALFORD, NEWELL G., Sgt., Bureau of War Risk Insurance, Headquarters 84th Division. '14 ALLEN, HEMAN H., Private Co. D., 8th Reserve Engineers. '17 AMBLER, HARRY A., Lieut 30th Infantry. '16 ANDERSON, ALEXANDER, Lieut Royal Garrison Artillery. '07 ANDERSON, GEORGE K., JR., See. C, 1st Co., 3d Officers' Training Camp. '17 ANDREWS, CLARENCE W., 1st Infantry Co., Officers' Training Camp, 83d Division. '13

Jan 1, 1923

By R. F. Bell, L. W. Eastwood, R. W. James

Among those concerned with the annealing and heat-treating of aluminum and aluminum alloys, it is well known that after co1d-working a coarser grain is usually produced by slow heating than hy more rapid heating. Consequently, for the control of the grain size produced by annealing or heat-treating cold-worked aluminum and aluminum alloys, the heating rate is of considerable practical importance. References in the current literature on the effect of heating rate are numerous, but it appears neither necessary nor desirable to give here a review of the former nark done on this subject. It became evident during some preliminary work on the recrystallizn-tion of aluminium and aluminum alloys that the effect of heating rate depended upon the type of microstructure of the metal. This observation led to the following study of the relationship of the type of microstructure of the alloy to the effect of the heating rate. Materials Investigated Analyses of the aluminum and aluminium alloys investigatted are given in Table 1. Three classes of material are listed, as follows: Class I.— Belonging to the first class are pure aluminium and aluminium containing a second constituent that is soluble in the aluminium matrix at

Jan 1, 1939

By R. F. Bell, R. W. James, L. W. Eastwood

Among those concerned with the annealing and heat-treating of aluminum and aluminum alloys, it is well known that after co1d-working a coarser grain is usually produced by slow heating than hy more rapid heating. Consequently, for the control of the grain size produced by annealing or heat-treating cold-worked aluminum and aluminum alloys, the heating rate is of considerable practical importance. References in the current literature on the effect of heating rate are numerous, but it appears neither necessary nor desirable to give here a review of the former nark done on this subject. It became evident during some preliminary work on the recrystallizn-tion of aluminium and aluminum alloys that the effect of heating rate depended upon the type of microstructure of the metal. This observation led to the following study of the relationship of the type of microstructure of the alloy to the effect of the heating rate. Materials Investigated Analyses of the aluminum and aluminium alloys investigatted are given in Table 1. Three classes of material are listed, as follows: Class I.— Belonging to the first class are pure aluminium and aluminium containing a second constituent that is soluble in the aluminium matrix at

Jan 1, 1939