Search Documents

By Chester Wells Purington

Situation.—The Camp Bird mine is in Imogene basin† (Fig. 1) at the head-waters of Canon creek, a branch of the Gunnison, in the southern part of Ouray county, Colorado, towards the northern edge of the region known as the San Juan mountains, and about 10 miles W. of the continental divide. It is 8 miles by wagon-road from Ouray, the terminus of a branch of the Rio Grande' Southern railway. The distance from Denver to Ouray is 387 miles by rail. In an air-line, the mine is 190 miles SW. of Denver. The altitude of the town, tunnel and buildings is 11,200 ft., and level No. 2 is 11,500 ft., and No. 1 is 11,670 ft., above sea-level. The lowest point of the lode-ontcrop, which crosses the basin E. and W., has an elevation of 11,850 ft., and that of the highest point, on the divide between Imogene and Tomboy basins, is 13,250 ft. On the eastern slope of the Imogene basin (towards Ironton) the vein is less clearly defined on the surface. Ownership and Extent.—At the time of the writing of this paper, the property is owned by Mr. Thomas I?. Walsh, and operated under the management of Mr. J. W. Benson. It

Jan 1, 1903

By Edward Keller

In a paper, " A Study of the Elimination of Impurities from Copper-Mattes, etc.," presented to the Institute at the Atlantic City meeting, February, 1898, I gave certain figures which I called the relative slaggability in refining copper. In that paper* will be found the following pertaining to this subject: Relative Slaggability in Refining Converter-Copper. Cu. Pb. Bi. Sb. As. Se, Te. 1 129.5 1.13 7.30 5.22 0.81 and Relative Slaggability in Refining Electrolytic Copper. Cu. Pb. Sb. As. 1 41 9.97 7.13 Since there is a, possibility of misinterpretation of the above values, the following supplementary information may seem justified in explanation. As the contents of impurities in the unrefined or crude copper were unknown, the contents of the refined copper were substituted therefor, merely in order to obtain the two series of figures for comparison. These figures are higher than they would be had I been able to take the correct ones for the unrefined copper. The high figure, 129.5, for lead, in the case of converter-copper, means simply that more lead was slagged from the crude copper than remained in the refined copper; or, in definite values, that to 1 per cent. of copper slagged, the ratio of the lead gone into the slag and the lead remaining in the refined copper is 129.5 : 100. It is possible to approximate the true slaggability much more closely by adding the quantities of impurities in the refined copper to those in the slag, thus obtaining values for the crude copper in which the amounts volatilized are ignored (the latter

Jan 1, 1901

By Albert F. J. Bordeaux

Alluvial gold was first discovered in Guiana in 1852, in the sands of the Arataye river, by Paulino, a Braziliaii convict. During the following years, gold was found also in the rivers Orapu, CirubQ, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Vat, and Couriege. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysee, Pas-Trop-Tot, date from 1878, and their production has been about %g5,000,000. In 1888, the Awa placers, along the boundary bet.ween the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company, the Dutch Guiana Freiich Minillg Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have produced about $18,000,000 in six years (1894-1900), but not even one-fourth of tho production went through French Quiana and

Jan 1, 1911

By C. E. Richards, C. N. Reid

The influence of preferred orientation on the incidence of defbrtnation tuinning has been studied. High-purity iron with almost vandonz grain orientation was cotnpared uitll iron of the sa)ne grain size and composilion lza,ing a strong (110) fiber texture. As expected from published work on single crgslfls, /he ))lean stress for the onset of luitzning-, and the l,olu)nt. fraclion of twinned nzaterial obserlled in lension differed fron the 1-a1ue.s it2 co?nPression for tnolerial with a slrong texlure. The llinning stress of "rctndorrl " )zalerial did not 17ary with the sense of the aPPlied unin.via1 stress, but sirprisinglg the incidence of 1c)i)zning- was about three 1i))zes greater ill conzp?&apos;ession Illon in lension. These results (Ire attributed entirely to ovienbation and may be nderslood in ler?ns of the shear slresses acting on the allowed twinning syster)is. J. HE twins most commonly formed in bcc metals may be described as regions of the crystal in which a particular set of (112) planes is homogeneously sheared by 0.707 in the appropriate ( 111) direction. A similar twin-related crystal could be produced by a shear of 1.414 in the reverse (111) direction but twinning by this large displacement has never been reported. Thus, twinning is unidirectional and a shear stress which produces twinning does not do so when its sense is reversed. The sense of a shear Stress is reversed when the loading is changed from tension to compression, or vice versa. Consequently, for a given orientation of a crystal relative to a uniaxial stress, only a fraction of the twelve (112) twinning systems are geometrically capable of operating in tension, and the remaining systems may operate only in compression. Therefore, when twinning is involved, there are expected to be differences in behavior between crystals tested in uniaxial tension and those tested in compression. This has been verified experimentally by Reid et 01.&apos; and Sherwood el al.,&apos; although a critical stress criterion was not encountered. Furthermore, twinning stresses in colmbium," tungten, tantalum,&apos; irn,&apos; i-Fe,\ nd molybdenum7 single crystals have been shown to depend critically on orientation, although again twinning did not occur at a critical value of the macroscopic shear stress. However, when twinning occurs, it generally does so on the most highly stressed systems, 1--4&apos;6&apos;8&apos;9 implying that the stress level does have some relevance to twin formation. In view of the large orientation dependence of twinning in bee single crystals, it might be expected that such an effect would be present in poly crystalline material which possesses a recrystallisation texture. Indeed, riestner" showed that the twinning stress in tension is very orientation-sensitive it1 <&apos;grain-oriented, silicon-iron;" this material possessed a very strong t c m^ii a nnr x_____k . i-_ii__ ri_______j. _x r»i_._:__i preferred orientation obtained by secondary recrystallisation. Reid et a/.&apos; observed a marked difference in the tensile and compressive yield stresses of polycrys-talline columbium which was rationalised in terms of the effect of a preferred orientation on twinning. No other such illformation is known to the authors. Several investigations of twinning in polycrystalline bcc metals have been reported in which the possible existence of a preferred orientation was not even mentioned. It is the purpose of this paper to show that there is a strong effect of texture on twinning in polycrystalline iron, and to poilt out the difficulty in eliminating preferred orientation in recrystallised metals. 1. EXPERIMENTAL METHOD Material and Specimen Preparation. Low-carbon, high-purity iron was obtained from the National Physical Laboratory in the form of $-in. diam rod which had been cold-swaged from a diam of 1 in. The composition of the material is given in Table I. The as-received bar was cold-swaged directly to 0.185 in. diam from which cylindrical tensile and compression specimens were machined. Specimen geometry is illustrated in Fig. 1. The gage length was 0.30 in. long and 0.10 in. diam; it should be noted that, apart from the extra heads which are necessary for tensile loading, the geometry and dimensions of the two types of specimen are identical. The specimens were heat treated either by sequence A or B outlined in Table 11. The essential difference between these two treatments is that in one case the material was repeatedly cycled through the y- to a-phase change in order to produce grains of almost random orientation ("random" iron)

Jan 1, 1969

By AIME

In Emporia or Claremore, time was when a path was beaten to the door of the local sage. Nowadays, the beginnings of such a path are discernible in Tennessee, as folks of the metallurgical persuasion find it to their pleasure and profit to call upon the Sage of Copperhill. They come, more and more respectfully as the years go by, yet to ever fewer persons is he known as Mr. Myers, but to more, eloquently, as Jack. Find better ways to run your mill, find happier means of co-ordinating your humanities or serving your professional society, and it&apos;s just like the man said about the mousetrap. A druggist&apos;s son, born in Wisconsin, May 24, 1889, reared on the Bible in Ohio and Indiana, and completing his education in Colorado, this now indisputably 24-carat Tennesseean has had a checkered career. Going West as a laborer at the tail end of the 1907 panic, he did not make his fortune but he did gain an understanding of labor that in later years endeared him to his men. Graduating in 1913 from Colorado School of Mines with the degree of E. Met. and a string of football letters (also earned the hard way, at tackle) he went to work in Butte & Superior, just at the beginning of the Golden Age of flotation.

Jan 1, 1949

By W. C. Hagel, H. J. Beattie

Seven austenitic alloys of varions base compositions and minor-alloy additions were solution-treated, aged systematically between 1200oand 1800oF, and examined by X-ray and electron metallography. Intragranular preczpitations of µ, Laves, s, ?&apos;, Ni3Ti, and x phases were observed as a function of composition and aging time and temperatwre. Phase solubility limits were detevtnitzed within 100Fo intervals. These inter metallic compounds fall into two distinct general classes, and whichever class predomznates depends on base composition. It has become increasingly evident that multicom-ponent austenitic alloys are well characterized by their precipitation processes. Since certain groups of elements act as one, the relationships among these processes are reasonably simple; complete identification of such processes is usually attainable by a systematic aging study with a combination of techniques centered on microscopy and diffraction. Several nickel- and cobalt-base alloys illustrating cellular precipitation and its interaction with general precipitation were reported previously.1 The group of alloys covered in the present paper demonstrates precipitation-hardening reactions involving two distinct classes of intermetallic compounds where the predominating class appears to depend on base composition. This dependency ties in with a crystal-chemistry regularity first observed some twenty years ago by Laves and Wallbaum but never amplified to our knowledge. Results of electron-microscope and X-ray diffraction studies on systematically aged hot-rolled alloys known commercially as S-816, S-590, Rene-41, Incoloy-901, M-308, and M-647 are reported here. Some of these alloys have previously undergone minor-phase analyses by other investiators. Alloy S-816 was investigated by Rosenbaum, Lane and Grant,3 and Weeton and Signorelli.4 Rosenbaum found only CbC in hot-rolled bars. Lane and Grant found CbC and a small amount of M6C in the cast structure and stated that both carbides form during aging, most of the precipitation being CbC. Weeton and Signorelli found CbC, M23C6 and a weak indication of a phase after a slow step-down cooling cycle from 2250°F. Rosenbaum also investigated hot-rolled samples of S-590 and identified CbC and M6C. Preliminary information on Rene-41, gained partly from the present work, was reported by Morris.5 Long-time precipitation phenomena in Incoloy-901 at 1350°Fwere investigated by Clark and Iwanski.B heir raw data re- semble those of our present heat with 0.1 pct B, while their interpretation of these data resembles our interpretation of data from another heat with only 0.001 pct B; they made no statement as to boron content. No previous minor-phase studies of alloys M-308 or M-647 have been reported. EXPERIMENTAL METHODS Table I gives alloy compositions in both weight and atomic percent. Specimens were solution-treated from 1700º to 2200ºF, aged at logarithmic-time intervals up to 1000 hours between 1200 and 1800 F, and examined in accordance with procedures previously described in detail. &apos; &apos; Phase extractions were carried out in electrolytic cells containing 800 ml of either 7 pct HC1 in denatured ethanol or 20 pct H3PO4 in water. After electrolysis for 48 hr at 0.1 to 0.2 amp per sq inch, residues were separated by filtration or centrifuging. X-ray powder patterns of residues were recorded on a diffractometer for accuracy and on film for sensitivity. Lattice parameters were calculated by least-squares analyses of indexed sin 8 values, and relative abundances were estimated from intensities of strongest lines of each phase. These phase abundances denote relative amounts with respect to each other rather than to the alloy. Mechanically polished specimens were etched in a freshly mixed solution of 92 pct HC1, 5 pct H2SO4, and 3 pct HNO3. Parlodion replicas for the electron microscope were chromium-shadowed in high vacuum at a glancing angle of 20deg. All electron micrographs are reproduced here with the shadowing source above. The correspondence betweenelectronmicrostructures and phases identified by X-rays was established by a high redundancy of correlation between relative amounts at different stages of aging and examination above and below critical transformation or solubility temperatures. EXPERIMENTAL RESULTS S-816 and S-590—The phases found in S-816 and S-590 after various aging and solutioning treatments are listed in Table 11. These data and the observed

Jan 1, 1962

By W. B. Dancy, A. Adams

Laboratory test work on heavy liquid separation of sylvite from halite is reported. Numerous tests were run on sylvite ore sized in the ranges of 4x20 mesh, 10x65 mesh, 8x100 mesh, -8 mesh and -10 mesh with heavy liquids in the range of 2.05 to 2.15 sp gr. From the test results, it was concluded that, with the type of ore under study and a size in the range of -8 mesh, a recovery as high as 90% could be achieved with a product grade of 70% KCl. However, a final product at an acceptable recovery cannot be made with one pass, and the float must either be further processed with heavy liquids or dried and sent to a conventional froth flotation circuit. Potash ores occurring in this country consist essentially of sylvite and halite plus minor amounts of magnesium sulfate salts and montmoril-lonite-type clays. Recovery of potash minerals from evaporite ores in the North American potash fields is accomplished almost exclusively by use of amine flotation. European practice involves froth flotation as well as solution-crystallization processes. Laboratory and pilot plant test work has been reported in Europe and the U. S. on the application of heavy media separation to potash ore beneficiation. Work was probably discontinued because of lack of ore with the required very coarse liberation characteristics (1/8 to 1/2 in. liberation size). Sylvite, with a gravity of 1.99, and halite, with a gravity of 2.17, appear to be ideal for separation by heavy liquids, which are now available in gravities from 1.59 to 2.95. This paper reviews preliminary results obtained from laboratory test work on heavy liquid separation of sylvite from halite. TEST WORK The heavy liquids used in the tests under discussion were chlorobromethane, with a specific gravity of 1.923, and dibromethane, with a gravity of 2.490. These liquids, completely miscible, were combined in the proportions needed to give a mixture having the desired specific gravity. Feed for the laboratory tests was mine-run ore screened to the desired mesh sizes. In conducting the tests, the sample was fed at a constant rate into a stream of heavy liquid and the mixture directed into a small separatory vessel. The float overflowed into a collecting pan while the sink collected in the bottom of the separatory vessel and was removed at the end of the test. Approximately 500 g of feed constituted a charge. Pulp density of the feed was kept low to prevent particle to particle interference in separation. With feed in the range of 8x100 mesh, a pulp density of under 10% solids by weight was found advisable. With coarser feed the pulp density could be carried as high as 15% solids. Time of separation was very rapid. In the case of 4x20-mesh material, separation was effected in 15 to 30 sec; with -10-mesh feed, separation required about 1 to 2 min. SPECIAL EQUIPMENT Since heavy liquids are toxic to varying degrees, all separatory work was carried out in a standard laboratory fume hood. It was noted that complete removal of fumes was not being effected; therefore the hood construction was modified, resulting in a completely satisfactory arrangement for heavy liquid test work. In the interest of safety, details of this fume hood are reported here. Unlike most fumes, heavy liquid fumes tend to settle and flow like water, rather than to rise like a gas. Working on this assumption, a standard water drain was installed in the hood. Across the front of the hood a 1-in. barrier was constructed. In the rear of the hood a false back was installed, with an adjustable sliding door on both the bottom and top of this panel. As shown in Fig. 1, the exhaust fan pulled a vacuum behind the barrier, sucking the heavy fumes from the bottom of the hood. Another addition was the drying box, shown to the right of the hood. This is simply a box covered on top with hardware cloth and connected by a 6-in. inlet to the hood. Sample trays made of fine mesh wire filter screens were found ideal for drying samples. With this arrangement, air flowed completely through the sample and all fumes were drawn into the hood. In use, it was found effective to cover with a

Jan 1, 1963

By Andrew S. McCreath

THE manufacture of pig iron for conversion into steel by the Bessemer and open-hearth processes, is now one of the most important industries of the United States. It is necessary that iron intended for this purpose should be very pure, and especially must it be comparatively free from phosphorus. Great care must therefore he exercised in the selection of proper ores, flux, and fuel. Only such ores as are practically free from phosphorus can be used, and pure fuel is as much a necessity as pure ores; though hitherto iron men have paid comparatively little attention to this point. During the course of my work as chemist for the Second Geological Survey of Pennsylvania, I had occasion to examine some of the bituminous coals of the State for phosphorus, and the results obtained are so interesting that I venture to present them to the notice of the members of the Institute. The coals are arranged in geological order according to the different beds, and the table shows the percentage of phosphorus in the coal and also in the coke. The greatest number of specimens have been selected from the Pittsburgh bed, because it is the principal coal-bed of Southwestern Pennsylvania, and most of the mineral fuel which is mined along the Youghiogheny and Monongahela rivers, to be used in the coke ovens of the Connellsville region and in the blast furnaces and mills of Pittsburgh and its vicinity, and to be shipped to Western and Southern markets, comes from this bed. It will be noticed that many of the specimens examined contain

Jan 1, 1880

In his paper, Sastry proposes the use of flotation methods other than the "conventional flotation!&apos; process as possible economical methods of removing mineral fines, The practice of Liquid/Solid separation employing microbubbles to assist or induce the flotation of suspended solids is common to both municipal and industrial waste- water treatment; and is also used as a separation step in some processing industries. The pretreatment (if any) of the stream prior to flotation, the source of the microbubbles, and the design of the separation vessel depend on the application. For example: a metal finishing plant would use an elaborate chemical conditioning scheme to precipitate metal hydroxides for removal by a dissolved air flotation unit operating in the effluent recycle mode, while some oily waste can be separated using a dispersed air flotation cell with no chemical conditioning. At the present time, the "conventional flotation" process employed by the mineral processing industry makes use of mechanical agitation and aeration to generate certain sizes and quantities of bubbles and to mix these bubbles with the pulp. Specific types of chemical conditioning are used to obtain the desired results. For the separation of mineral fines, the type of chemical conditioning, bubble generation and separation device needed to obtain optimum results will have to be determined through research. The point to be made is that while the principles of flotation separation can be applied to a wide variety of applications, the specifics of the flotation process may vary with each application. Sastry&apos;s paper has dealt with the many areas of research required to fully understand and utilize the flotation process for the beneficiation of mineral fines.

Jan 1, 1979

By Claude H. P. Lupis, John F. Elliott

QUITE generally an increase in the temperature tends to bring a system closer to ideality. It is reasonable as a first approximation to consider that the excess free energy will vary linearly with the temperature, or: where t may be defined as the "characteristic temperature" of the solution, or the temperature at which the system would become ideal if the results at T were linearly extrapolated. It must be emphasized that consideration of this hypothetical property is an appeal to intuition rather than an established physical concept. The order of magnitude of 7 for dilute solutions will depend on the nature of the solvent; a value of 3000° + 1000°K may be suggested for ordinary metallic solutions. In terms of free energy, entropy, and enthalpy first-order interaction coefficients, differentiation of the above equations with respect to composition leads to The concept of t offers a simple and plausible interpretation of Chipman and corrigan&apos;s3 recent empirical correlation between and a for a number of groups of ternary systems 1-24. The authors found that in each group the ratio was approximately constant. The corresponding calculated from their data by Eq. [4] are listed in Table I. The expected order of magnitude is obtained for 7. As noted by Darken,4 if a regular solution is not assumed, thus if utj) # 0, Chipman and Crrigan&apos;s results imply that, as T is increased, ultimately changes in sign, Fig. 1. Clearly Eq. [4] is valid only in a limited range of temperatures since at the temperature 7 at which the system becomes ideal not only should become null but also and . Thus, both and are functions of

Jan 1, 1967

By D. S. Cahn, D. W. Fuerstenau

Specimens of glass, plexiglass, and naturally occurring minerals were irradiated by a 15-joule ruby laser pulse to determine criteria for the fracture of nonmetallic solids by internal thermal stresses. Fracture did not occur in those specimens with either a very high or very low internal absorptance or with a high spectral reflectance. If significant amounts of melting and vaporization do not occur at the surface of irradiation, the specimen will fracture if a derived 11fracture stress" exceeds the ultimate tensile strength of the specimen. The purpose of this investigation was to determine criteria for the fracture of nonmetallic solids by internal thermal stresses which are caused by absorption of laser irradiation. A laser produces a very short pulse of light which has a high energy density distributed over a very narrow part of the visible spectrum. The laser system used in this investigation had an energy output of 15 0 joules at a wavelength of 6940 A. Fracture in a non-metallic solid, then, would be caused by the absorption of light energy by that solid, and subsequent conversion of this energy to heat or mechanical energy. Fracture is caused by internal stresses that result from rapidly imposed nonequilibrium thermal gradients. ANALYSIS OF CONDITIONS FOR FRACTURE BY LASER IRRADIATION For this analysis, the laser beam is assumed to be circular and centered on the junction of the major and minor axes of a rectangular specimen. The laser beam forms a cylinder of radius rb extending through the specimen width. The beam cylinder may be then thought of as a heated mass constrained by a surrounding unheated mass. The instantaneously heated cylinder will at-

Jan 1, 1968

By R. G. Stickney

INTRODUCTION The Basalt Waste Isolation Project, conducted by Rockwell Hanford Operations under contract to the U.S. Department of Energy, is assessing the feasibility of the disposal of commercial radioactive spent fuel/high-level waste in deep geologic formations in basalts beneath and within the Hanford Site in southeastern Washington State. The Basalt Waste Isolation Project mission is to identify and characterize a potential geologic repository site in basalt and to develop associated facilities and technology required for the potential permanent isolation of radioactive wastes in basalt formations. In support of the Basalt Waste Isolation Project, a laboratory testing program was conducted to evaluate the performance of the Council for Scientific and Industrial Research&apos;s "Doorstopper" biaxial strain cell. To support site characterization studies and the design of repository openings, in situ stress measurements will be conducted within the reference repository horizon (~970 m). The Doorstopper is one of the instruments being considered for use in these measurements. It was selected because it requires only a small volume of work to achieve stress relief, which is important in a closely jointed basalt. Also, test durations are short, permitting a large number of measurements to be made within a given time to increase confidence in the results. Within the reference repository horizon, temperatures are expected in the range of 40º to 60°C with a humidity of up to 100%. For this testing program, test conditions were selected to closely resemble those expected within the repository horizon. The Doorstopper test, mainly developed by Leeman (1964), is a strain rosette relief method of measuring rock stress in situ. The Doorstopper consists of a four element, 45º strain gage rosette

Jan 1, 1984

By M. Gensamer

THE stresses which initiate deformation processes in metals are funda-mentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals1 has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.2 It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. ? Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals.

Jan 1, 1938

By L. C. McCabe

THE object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrain1 was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.-Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may he used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indic-ative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.-Early in the present investiga-tion several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maxi-mum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the follow-ing paragraphs.

Jan 1, 1937

By Joseph Hodgson

IN 1880, mining operations were commenced at the Copper Queen mine. The famous Queen orebody, which extended to the surface, was first quarried from a large open cut in the outcrop. The orebody was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and. Escabrosa limestones. While the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, While remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown y large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and deadwork in this property.

Jan 8, 1914

By C. R. McClure

The objective of this papef is to summarize briefly the practical use of rock mechanics in design and construction of various types of structures. These range from foundation for industrial facilities, nuclear power plants, bridges and dams to tunnels and underground caverns. The use of rock mechanics has varied from performing a few laboratory unconfined compressive tests on core samples to complete field and laboratory tests for underground power caverns. The primary difference between the rock mechanics studies we hare for construction projects and those most commonly found in the literature is that our tests must provide immediate answers to specific questions facing a design or construction engineer. For example, when we make a plate-bearing test we arrive at a load-deformation relationship. We realize that this is not a true modulus of elasticity. Yet, when considering the resistance the rock will provide against forces occurring in a pressure tunnel it is a far more useful value than the true modulus of elasticity of the rock. Another example of this difference in interest is in the use of flat jacks. Many people criticize the use of flat jacks because they measure the stresses in the disturbed zone very near the surface and do not represent the undisturbed stress condition in the rock. However, in actual construction it is frequently those near-surface stresses with which we must cope. We are interested in both the stress conditions present prior to excavation and those as modified by construction of an exploratory adit or drift. Fundamentally, we are interested in the practical application of rock mechanics in the solution of problems of design and construction of civil engineering works.

Jan 1, 1968

By H. A. Doerner

PROPOSALS to use hydrocarbon or natural gases for the reduction of zinc from oxide materials may be traced back through Patent Office files to the early years of the present century. Natural gas at rates cheap enough to compete with solid fuels has been available at or near one major zinc district for more than a decade. That the seemingly meritorious and economically interesting applications of these proposals have not devel-oped into workable processes for direct production of zinc by natural gas cannot be completely ascribed to the proverbial conservatism of the zinc industry. It is possible to produce spelter commercially in normal times from zinc oxide and carbonaceous reducing agents without having a very precise understanding of the chemistry of the process. The reduc-tion by hydrocarbons is not, however, in this class, and the technical complexity of this reduction metallurgy and chemistry prohibits solution of the inherent difficulties by the "hit and miss" methods that are some-times thought to be practical. In a thermodynamic study of the chemistry of zinc smelting, Maier1 made a preliminary study of the chemistry of the use of methane for reducing zinc oxide by thermodynamic means, pointing out that the following reactions, the limits of which could be theoretically predicted, were important: ZnO + CH4 = Zn(gas) + CO + 2H2 [1] CH4 = C -I- 2H2 [2] ZnO + CO = Zn(gas) + CO2 [3] ZnO + H2 = Zn(gas) + H2O [4] Other possible reactions, not discussed in the reference quoted, are: CO2 + CH4 = 2CO + 2H2 [5] H2O + CH4 = CO + 3H2 [6]

Jan 1, 1933

By Alfred Wandke

The problem of vein formation has been of particular interest to the writer for years. As his work for a long time was confined largely to districts showing large deposits of copper ore, it was natural that the efficiency of replacement, as one if not the chief control of the emplacement of the ore, seemed a particularly attractive hypothesis. Of late years, in almost daily underground work in the Guanajuato district, he has collected evidence which makes it certain that in a number of cases the ore solutions were under sufficient pressure to force the rock walls apart and to hold them apart, thus offering an open space for the deposition of vein and ore-bearing material. This paper will concern itself with conditions frequently met with in hypogene ore deposits of the vein type, and will deal in particular with ore occurrence in precious-metal veins of the type classified by Lindgrenl as epithermal deposits, or metalliferous deposits formed near the surface by ascending thermal waters2 and in genetic connection with igneous rocks. To account for the emplacement of this type of ore deposit various writers have suggested the following agencies: 1. Shattering of the wall rocks. 2. Pressure of growing crystals. 3. Magmation, as treated at length by Spurr3. 4. Replacement. 5. Openings produced by folding. 6. Shearing due to gravity. 7. Shrinkage produced by the passage of pre-ore solutions. 8. Contraction joints produced by lateral secretion. To this list there may be added another agency, a discussion of which forms the basis of this paper: 9. Pressure of the ore-bearing solutions.

Jan 1, 1931

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By Carle Hayward

THIS work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author&apos;s direction. They attempted to determine the diagram for the system Cu2S-NiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried, on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.1 At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages.

Jan 1, 1914