Search Documents

By J. D. Miller, J. E. Sepulveda

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence' gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource. The projected increase in the ever-widening gap between the domestic energy demand and the domestic energy supply for the next few years has motivated renewed interest in energy sources other than petroleum, such as tar sands, oil shale and coal. Although a number of research programs on the exploitation of national coal and oil shale resources have already been completed, very few programs have been initiated on the processing of tar sand resources in the United States. In recognition of their significance as a domestic energy resource, investigators at the University of Utah have designed an extensive research program on Utah tar sands. An important phase of this program, and the main subject of this publication, is the development of a hot-water process for the recovery of bitumen from Utah tar sands, as a preliminary step toward the production of synthetic fuels and petrochemicals. The term "tar sand" refers to a consolidated mixture of bitumen (tar) and sand. The sand in tar sand is mostly a-quartz as determined from X-ray diffraction patterns. Alternate names for "tar sands" are "oil sands" and "bituminous sands." The latter is technically correct and in that sense provides an adequate description. Tar sand deposits occur throughout the world, often in the same geographical areas as petroleum deposits. Significantly large tar sand deposits have been identified and mapped in Canada, Venezuela and, the United States. By far, the largest deposit is the Athabasca tar sands in the Province of Alberta, Canada. According to the Alberta Energy Resources Conservation Board (AERCB),2,3 proved reserves of crude in-place bitumen in the Athabasca region amount to almost 900 billion bbl. To date, this is the only tar sand deposit in the world being mined and processed for the recovery of petroleum products. Great Canadian Oil Sands, Ltd. (GCOS) produces 20 million bbl of synthetic crude oil per year. Another plant being constructed by Syncrude Canada, Ltd. is expected to produce in excess of 40 million bbl of synthetic crude oil per year. According to the Utah Geological and Mineral Survey (UGMS), tar sand deposits in the state of Utah contain more than 25 billion bbl of bitumen in place, which represent almost 95% of the total mapped resources in the United States.4 The extent of Utah tar sand reserves seems small compared to the enormous potential of Canadian tar sands. Nevertheless, Utah tar sand reserves do represent a significant energy resource comparable to the United States crude oil proved reserves of 31.3 billion bbl in 1976.5 Tar sands in Utah occur in 51 deposits along the eastern side of the state.4 However, only six out of these 51 deposits are worthy of any practical consideration (Fig. 1). As indicated in Table 1, Tar Sand Triangle is the largest deposit in the state and contains about half of the total mapped resources. Information regarding the grade or bitumen content of Utah deposits is still very limited. The bitumen content varies significantly from deposit to deposit, as well as within a given deposit. In any event, the information available6-8 seems to indicate that Utah deposits are not as rich in bitumen as the vast Canadian deposits which average 12 to 13% by weight.9 Although many occurrences of bitumen saturation up to 17% by weight have been detected in the northeastern part of the state (Asphalt Ridge and P. R. Spring), the average for reserves in Utah may well be less than 10% by weight. Separation Technology As in any other mining problem, there are two basic approaches to the recovery of bitumen from tar sands. In one

Jan 1, 1979

By Benjamin C. Craft, Frank Perkins

The wall-building properties of salt-water muds can be maintained at high temperatures by additions of gum karaya, gum ghatti, gelatinized starch, or commercially prepared starch. A germicide should be used to prevent fermentation. Introduction The behavior of drilling mud has received special attention from the petroleum industry within the past few years in numerous research projects dealing with such subjects as chemical treatment, gelation, and filtration characteristics. The importance and control of filtration, or water loss, is readily apparent* It affects the analysis of side-wall cores and interpretation of electric logs; it controls to a large extent the work of primary cementing, reduces the amount of expensive fishing, and permits the running of long strings of casing. It has been found that among the many factors that have an adverse effect on filtration, the presence of electrolytes, in general, and of salt, in particular, is outstanding. The effect is one of flocculation of the colloids due to neutralization of the negative charges on the clay particles. This reaction is further increased on the Gulf Coast because high temperatures reduce dispersion, to a minimum, causing increased flocculation in both fresh-water and saltwater muds. The problem of reducing water loss in salt-water muds by the addition of gums and starch at atmospheric temperature has been investigated,' and many successful field tests in West Texas indicate its solution. From the work of Byck2 it is concluded that no existing method will permit an approximate determination of the filtration rate at high temperatures from data taken at room temperatures. Filtration should be measured at the ternperature actually anticipated in the well, or at least at a number of lower temperatures and extrapolated over a small range. A laboratory study has been made of the chemicals available for the filtration characteristics of salt-water muds at high temperatures, and the use of germicides to prevent fermentation. Laboratory Investigations Procedure Since the purpose of this investigation was to compare several different gums and starches at elevated temperatures, mud from the same source was used for all the tests. Viscosity was measured in a Stormer viscosimeter at 600 r.p.m. and water loss was determined with a Baroid High-pressure and High-temperature Wall-building Tester3 at temperatures from 80' to 250°F. and at a pressure of 500 lb. per sq. in. for 30 minutes. The samples tested consisted of 150 grams of commercial Louisiana mud, 50

Jan 1, 1943

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

By Benjamin C. Craft, Frank Perkins

The wall-building properties of salt-water muds can be maintained at high temperatures by additions of gum karaya, gum ghatti, gelatinized starch, or commercially prepared starch. A germicide should be used to prevent fermentation. Introduction The behavior of drilling mud has received special attention from the petroleum industry within the past few years in numerous research projects dealing with such subjects as chemical treatment, gelation, and filtration characteristics. The importance and control of filtration, or water loss, is readily apparent* It affects the analysis of side-wall cores and interpretation of electric logs; it controls to a large extent the work of primary cementing, reduces the amount of expensive fishing, and permits the running of long strings of casing. It has been found that among the many factors that have an adverse effect on filtration, the presence of electrolytes, in general, and of salt, in particular, is outstanding. The effect is one of flocculation of the colloids due to neutralization of the negative charges on the clay particles. This reaction is further increased on the Gulf Coast because high temperatures reduce dispersion, to a minimum, causing increased flocculation in both fresh-water and saltwater muds. The problem of reducing water loss in salt-water muds by the addition of gums and starch at atmospheric temperature has been investigated,&apos; and many successful field tests in West Texas indicate its solution. From the work of Byck2 it is concluded that no existing method will permit an approximate determination of the filtration rate at high temperatures from data taken at room temperatures. Filtration should be measured at the ternperature actually anticipated in the well, or at least at a number of lower temperatures and extrapolated over a small range. A laboratory study has been made of the chemicals available for the filtration characteristics of salt-water muds at high temperatures, and the use of germicides to prevent fermentation. Laboratory Investigations Procedure Since the purpose of this investigation was to compare several different gums and starches at elevated temperatures, mud from the same source was used for all the tests. Viscosity was measured in a Stormer viscosimeter at 600 r.p.m. and water loss was determined with a Baroid High-pressure and High-temperature Wall-building Tester3 at temperatures from 80&apos; to 250°F. and at a pressure of 500 lb. per sq. in. for 30 minutes. The samples tested consisted of 150 grams of commercial Louisiana mud, 50

Jan 1, 1943

AT a luncheon attended by engineering leaders representing every section of the country, Col. Arthur S. Dwight, president of the American Institute of Mining and Metallurgical Engineers, and Charles F. Rand, chairman of the Engineering Foundation, past president of the Insti-tute and its present treasurer, on Thursday, July 20, were decorated with the Croix de Chevalier de la Legion d&apos;Honneur by the French Government for distinguished service in engineering tending to closer and more felici-tous relations between the two countries. The decorations were conferred by Consul General Gaston Liebert. In a speech extolling the war work of the American engineer, M. Liebert declared that Germany had been definitely foiled in her attempt to cripple France industrially for a generation by wrecking the coal mines of northern France. Three-fourths of these mines, M. Liebert said, were in full working order and the remainder will be in complete operation within two years. The Germans thought that it would take from 15 to 20 years to accomplish this. M. Liebert said that reconstruction is going on rapidly in northern France, two-thirds of whose indus-tries are now working. The French Government, he said, is planning water-power improvement on a vast scale, which will soon make unnecessary for France to import a single ton of coal. He urged that French students be sent to America to study engineering. In presenting the decorations, Consul General Liebert eulogized Colonel Dwight and Mr. Rand as personify-ing the spirit and service of the American engineer, which, he said, was a powerful factor in the victory over Germany. He spoke of the growing friendliness between the United States and France and described this ceremony as an epoch in international relations. Calvin W. Rice, secretary of the American Society of Mechanical Engineers, who presided, repeated that international unity among engineers was the dream of Andrew Carnegie, who saw in the efforts of the engineer and the scientist the hope of civilization. Mr. Rice said in part: In the Declaration of Independence occurs the statement that all men are created free and equal. Jefferson was familiar with the writings of Rousseau. In fact, he was a remarkable linguist notwithstanding that he wrote the Declaration of Independence when only 32 years of age. He was one of the very few ambassa-dors in the history of the United States who could speak the language of the country to which they were sent. The interpretation of the passage in the Declaration of Independence is that all men have equal opportunity, not that they are born with equal ability.

Jan 8, 1922

By C. W. Green-Halgh

The accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (1) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries arc poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money. or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. Object of Examination The Purpose of prospecting any mineral deposit is to secure sufficient samples from which Ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, &apos;pan the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By Franz R. Dykstra

DEFINITIONS The ores of iron are classified in three general categories: direct shipping, concentrates, and agglomerated-i.e., pelletized or sintered. Direct Shipping As the name implies, direct-shipping ores are shipped as mined or, perhaps, after screening. Generally, direct-shipping ores are hematitic (R203), magnetitic (R304), or limonitic (2Fe2O3.3H20) in nature. Grades of direct-shipping ores vary widely. Prices are frequently related to the historical Mesabi standard of 51.5% iron, although certain premium lump ores may contain up to 68% iron. The use of direct-shipping ores is diminishing as the advantages of beneficiated ores become evident and reserves are depleted. Concentrates Where the nature of the deposit and economics allows, certain ores are upgraded. This may include no more than washing and screening, or may be as elaborate as fine grinding followed by magnetic, gravity, or even flotation procedures for separation. Coarser concentrates may be smelted "as is.&apos;; Fine concentrates usually are sold as sinter feed. (Sinter, as used here and in the following, refers to a process by which a fine ore-carbon mixture is agglomerated at elevated temperatures on a direct-fired moving grate to eliminate fines and improve chemical and physical homogeneity.) Agglomerates-Pellets or Sinter The development of economic techniques of mining and concentrating taconite (fine-grained, ferruginous jasperoids) led to the introduction of the iron-ore pellet, which is now becoming the major form in which iron is introduced into the furnace. The tremendous reserves of magnetic taconites of the northern United States and Canadian Precambrian shield had been recognized for many years. A century of mining has seen the reserves of the direct-shipping or "red ores" of the Minnesota, Michigan, and Wisconsin ranges approach depletion. Research started in the 1930s has seen the evolution of motives and techniques to concentrate these stubborn refractory ores. The efficacy of concentrate pellets in iron-making has been such as to induce mines throughout the world to grind, concentrate, and pelletize otherwise shipping-grade ores. Table 14.1A.1 shows typical analyses of iron ore. Marketing-Prices of iron may be quoted on a value per long-ton (2240 lbs) or metric-ton (1000 kg or 2204 lb) basis, or on a value per long-ton-unit or metric-ton-unit basis. One iron unit represents 1 % of contained iron per ton. (Thus, a price of $0.45 per iron unit for ore containing

Jan 1, 1976

By E. A. Smith, E. R. Parker

METALLURGISTS and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applications and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. Single-crystal copper specimens were broken in tension at impact velocities up to 100 ft. per sec. The distribution of slip bands in the fractured crystals was found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. EXPERIMENTAL PROCEDURE Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were made into test bars by sliding threaded steel bushings over each end of a crystal and then flowing silver solder between the crystal and the bushing. The inside diameter of the bushings was slightly greater than the diameter of the crystals, to allow space for the silver solder. The bushings were placed so that the gauge length of the crystals was one inch. The assembly is shown in Fig. I, with two views of a fractured crystal. Annealed polycrystalline copper bars of similar shape were machined from solid stock. X-ray measurements were made on all single crystals to determine their orienta¬tions. The results are shown in Fig. 2, where the location of the axis of each specimen is indicated on a standard projection. The bars were broken in a commercial variable-velocity tension im¬pact machine, which has been described in detail elsewhere.7,8 The stress and strain were recorded by means of wire strain gauges and a special commercial oscillo-raph, also described in detail elsewhere.9,10 The equipment and method can be briefly described as follows. The impact machine consists of a motor-driven flywheel containing a two-pronged hammer. This hammer is held retracted in the flywheel

Jan 1, 1944

By H. A. Wilhelm, P. Chiotti, G. A. Tracy

A summary of analytical, X-ray, thermal, and metallographic data obtained in the study of the Mg-U system is presented. No intermetallic compounds are formed by these two elements, and their mutual solubility is limited at temperatures up to 1255°C. The compositions of the liquids which coexist at 1135°C under a pressure of 3 atm are 0.14*0.05 wt pet U in magnesium, and 0.004 wt pet Mg in uranium. The solubility of uranium in magnesium decreases to 0.0510.03 wt pet at 675OC, and to about 0.0005 wt pet at 650°C. Due to the reactivity of both uranium and magnesium toward crucible materials, the choice of a suitable crucible presented a problem. Crucibles made from high purity magnesia to which 10 wt pet MgF2 was added to reduce porosity proved to be satisfactory. Some observations made with the use of other crucibles are given. THIS investigation was made to establish the phase diagram for the Mg-U system. Ahmann,&apos; formerly of the Ames Laboratory, did some work on the system. He used several methods in an attempt to prepare Mg-U alloys. One of the methods involved the reduction of UF, with a large excess of magnesium. In these experiments, the magnesium wet the surface of the uranium, but there was no evidence for compound formation. The maximum solubility of magnesium in uranium was indicated to be 0.01 wt pet. In another set of experiments, uranium chips as well as uranium powder were heated in contact with molten magnesium in a graphite crucible for periods of time up to 48 hr. A reaction layer was found at the Mg-U interface in several instances. X-ray analysis of the layer material showed the presence of UC and some additional unidentified lines which were interpreted as indicating the possibility of an intermetallic compound of uranium and magnesium. These studies indicated the maximum content of magnesium in uranium to be 0.043 wt pet. One sample of magnesium which had been heated at 1025°C in contact with excess uranium was found by chemical analysis to contain 0.275 wt pet U. Rules, based on empirical or semi theoretical considerations, which attempt to predict the alloying behavior of metals have been presented in the literature. Although these rules are not infallible, they nevertheless serve as useful guides. Using them, several generalizations can be made concerning the Mg-U system. According to Hume-Rothery&apos;s&apos; atomic

Jan 1, 1957

Discussion of the paper of L. A. DELANO, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1267 to 1286. L. A. DELANO.-Since this paper was written, our daily mill tonnage has increased, from 2100 tons to 2700 tons a clay. We now use 11,000 lb. of chrome-steel balls of 2 ½ -in. maximum diameter, for an average crushing capacity of 275 tons per 24 hr., this giving a much higher crushing efficiency. I wish to call attention to two typographical errors in my paper as published. On page 1271, Table 1, the screen analysis of ore at the Bonne Terre mill should be stated in inches instead of mesh. - On page 1272, "the rolls average 185 tons per 24 hr., and have shown by test that 250 tons per hour can be maintained" should, of course, read "250 tons per 24 hours." THE CHAIRMAN (0. M. BILHARZ, Miami, Okla.).-Is the increased mill capacity due to improvement in the re-crushing of middlings or to keeping middlings out of circulation and treating them separately? L. A. DELANO.-AS was shown in Mr. Rabling&apos;s paper (Bulletin No. 128, p. 1161) the tonnage was raised by about 400 tons by simply changing the arrangement of screen openings in the jig bed and using punched plate instead of woven-wire screen. Then, by adding a ball-mill, we are taking from the jigs a much larger tonnage of middlings than before or as much as the ball-mill will crush. By sending the ball-mill product to tables and flotation, the jig capacity for original ore is increased. CHAIRMAN BILHARZ.-In your opinion, the satisfactory operation of a Hancock jig on a given ore requires adjustment of the length of the different screens and careful selection of screen openings? L. A. DELANO.-I think it does. In order to decide what screen openings to use on the jigs, we did a great deal of experimental work, making screen analyses of the various hutch products, and then hand-sorting the galena, middlings and chat from each size screen to determine the percentage of galena in each. Then adjusting our jig screens, we gradually worked the process up to a very efficient basis. ERNEST GAYFORD, Salt Lake City, Utah.-I would like too ask Mr. Delano whether the work of the Allen cone has been quite as satisfactory as the manufacturers claim for it.

Jan 1, 1918

The annual world production of minerals approximates 1,700,000,000 tons, over 90 per cent. of which consists of coal and iron. Of this amount about two-thirds is used within the countries where the minerals are produced and one-third is shipped to other countries. The movement of most of these minerals, though, shows a rather remarkable concentration. For instance, manganese moves from three principal sources and converges at four or five consuming centers; chromite and tungsten move from two principal sources. The United States is more nearly self-sustaining in regard to mineral commodities as a whole than any &apos;other country on the globe; but the interests of conservation - call for an international viewpoint in the handling of our mineral resources., There is perhaps as much need of specializing in mineral output as there is of specializing in manufacturing. The thought that every country on the globe should be self-sustaining in regard to mineral supplies is of somewhat the same order as the thought that every family should produce all its own raw materials rather than take advantage of the more favorable conditions existing elsewhere and so specialize in human effort. Extension of international control of minerals seems to offer possibilities of loss and gain-loss through a considerable sacrifice of national trade .and a narrowing of the field for private initiative in trade; gain through the possibility of attaining certain ends which are attainable only by international agreement, such as an allocation of supplies which will be to the advantage of the greater number of nations rather than to the advantage of the few that are strong enough to dominate the situation. The interests of conservation clearly require international control. Moreover, the lesson of the war points to the necessity of overhauling old international understandings and machinery, even though such a task would encounter great difficulties, not the least of which lie in the persistence of human habits and inertia. Whether the time has come to establish a league of nations with economic control can be determined only by our individual and collective answers to the question whether we are willing to make the necessary economic sacrifices, individually and nationally, in the interest of world harmony. The mineral industry should fully understand that, with international control, efforts to promote export will need to be modified and curtailed; that expansion of our trade in many lines will mean equivalent loss of trade to other nations; that the almost universal conception that expansion of foreign trade is a meritorious aim and end in itself, without regard to its effect on other countries, will need revision.

Jan 3, 1919

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry&apos;s use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel &apos;economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

I AM sure, that you understand that of all the things created by the most high God Himself or by Nature at His command, not one-even though it be an atom or the smallest worm-has been produced without some particular gift. And if we do not always discern this in every thing, the cause lies in our defective vision, in our little knowledge, and in our lack of careful thought concerning the necessity of seeking hidden things. Certainly those things that have such inner powers, like herbs, fruits, roots, animals, precious stones, metals, or other stones, can be understood only through oft-repeated experience. [37] Others do not need so much knowledge and belief for their, powers are obvious and shown to us at all times by their effects. They reveal themselves to us through the sense of sight by their splendor and variety of colors, through the sense of smell by their odors, through the sense of hearing by the melody of the harmonious or unpleasantly discordant repercussions. of the air. They likewise manifest themselves by. their softness or harshness. As you see, all those things, according to. their limits, are conveyed .by the ordinary senses to the mind, by whose distinctions all their species, both harmful and beneficial, are discerned. Then they are reviewed by the judgment in all their degrees of perfection and imperfection, so that whoever seeks them with careful study or with experience often finds them. Now, in order to shorten this discourse, since I wished to speak to you of lodestone and its properties, I tell you that it is one of those things that show their apparent effects to our sight by a particular virtue hidden in such a way that its cause, as far as I know, has never been known to the very wise natural speculators who have spoken on every other subject. Thus one who considers its actions carefully must surely marvel, for it appears that Nature has put into this stone a certain spirit of vivacity, so that it seems to have-I would like to say-hands, although they are not seen. For I see that it not only attracts iron but also takes hold of it and keeps it attached to itself. This action is certainly great enough to bear certain witness to the virtues possessed by other created things that do not manifest their powers to the external senses. In order not to prolong this discussion, I tell you the following. This stone is found in various places and of different colors and properties. The

Jan 1, 1942

By Woolsey Johnson

THE object of this paper is to, describe the several necessary characteristics of the zinc-retorting charge and to show how by certain improved methods; the large excess of coal, over that theoretically required, can be reduced, thereby effecting an increase in the smelting capacity of a retort plant as well as other economies. In the Southwestern zinc works a charge of roasted zinc ore with a side mixture of carbonates and silicates, analyzing on the average 50 per cent. Zn, is mixed with 55 or more per cent. of its weight of a mixture of coal and coke analyzing 60 to 70 per cent. fixed carbon. . The ore is of varying fineness and the coal and coke are usually crushed in a semi-moist condition through a 3/8 -in. screen. With ores of a slaggy nature, this coal proportion is increased, sometimes to as much as 100 per cent. of, the weight of the ore. With carbonate ores, or where anthracite screenings with higher carbon content are cheap enough, the percentage of reducing agent is cut to 45 per cent. or even somewhat lower. The average charge per retort for a monthly run of a plant on ore, as distinguished from retorts on blue-powder, ladle-skimmings and other between-products, runs from 60 to 66 lb., with a mean of 63 lb. for the Southwest with standard retorts of 8 ½ -in. inside diameter and 50 in. long inside, using roasted sulphide ores. Conditions will change these figures, but 40 lb. of ore per cubic foot of retort space is, I believe, an average in the better-operated plants. Since the rise in. the price of spelter, the tendency has been to overcharge. To remove the slag that is formed when retorts are overcharged, extra men are put on to "gum-chisel" the retorts to prevent "set" furnaces and "butchered, retorts." Taking the above conditions as premises, we find that from four to six times the amount of coal necessary for the reduction is used, as is evidenced by the fact that the residues analyze as high as 35 per cent, fixed carbon. There are good reasons why this excess of fixed carbon must be used and perhaps these can be best explained by a description of the metallurgical requisites of a zinc charge. We may enumerate these as follows: 1. High reducing power, especially at the end f the shift, to reduce any carbon dioxide to monoxide and bring about a good condensation

Jan 2, 1918

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry&apos;s use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel &apos;economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By C. W. Greenhalgh

THE accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (I) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries are poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money, or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend. A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. OBJECT OF EXAMINATION The purpose of prospecting any mineral deposit is to secure sufficient samples from which ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, upon the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By R. D. Nelson, F. E. Bowman

Assumptions are made of ideal mixing and that the density of silver can be obtained by extrapolating reported liquid density-temperature data through the freezing point back to the temperature range of interest. The results of this procedure using liquid silver density data of Kirshenbaum et al.5 are presented in Table I1 where it is observed that agreement is everywhere within <0.1 pct and generally is within 0.05 pct. Because the Sn-Ag alloys are dilute, the assumption of ideal behavior is, therefore, probably justified. In conclusion, the densities of dilute liquid solutions of silver in tin have been determined. Even for concentrations as low as 0.1 pct, the effect of silver on the density of liquid tin is clearly measurable. This work also suggests that for dilute alloys at temperatures far below the freezing point of the solute metal, densities may be accurately calculated by extrapolation of the pure metal data without having recourse to physical measurement on the alloy itself. plutonium having a grain size of about 100 µ. This paper presents data showing that large elongations of fine-grained a Pu can be obtained by using slow deformation rates. Large plasticity, however, of a Pu in compression has been observed.4 Reductions in thickness of 90 pct have been observed with no edge cracking. These large reductions are accompanied by concurrent re-crystallization. The deformation modes, which are quite complex, have been studied extensively by observing the deformation microstructures of polished surfaces that had been deformed in compression.5-7 Although slip apparently is a predominant mode of deformation at room temperature, grain boundary sliding and concurrent recrystallization become more predominant at high a temperatures.4&apos;7 Although recovery occurs,8,9 no grain growth has been reported in a Pu even at temperatures near the a =ß equilibrium temperature (-115oC), which is 0.7 of the calculated melting temperature of a Pu.10 From studies on other materials, it appears that high elongations can be obtained in alloys when the THE purpose of this technical note is to present briefly some data revealing high ductility of a Pu, which is normally considered brittle. The very low ductility of a Pu in tension has been reported by many investigators.&apos;-3 Gardner,1 for example, reported that the total elongation of a Pu at a testing speed of 0.015 ipm is less than 0.1 pct at room temperature and only about 1 pct at 100°C. The only tensile creep studies that have been reported&apos; indicate no large ductility, but they were performed on relatively low purity

Jan 1, 1970

By W. J. Reagan

IN a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the vari-ous sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In. the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable &apos;indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2 in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be involved.

Jan 1, 1936

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

By C. R. McEwen

The displacement equations of Buckley and Lever-ett&apos; have been successfully applied to the prediction of oil recovery in frontal drives for a number of years. Commonly, the capillary pressure term is omitted from Leverett&apos;s fractional flow formula. The resulting satura-tion-vs-distance curves become multi-valued, however. Buckley and Leverett, recognizing that the neglect of capillarity was most likely the cause, proposed that this part of the solution he ignored. An ingenious method of propagating a discontinuity in place of the multi-valued portlon of the curve was devised by Cardwell using "non-capillary displacement theory". However, it would seem that a completc description of the displacement pracess would require the inclusion of capillary forces. Three publications on displacement theory have appeared in which capillary pressure was included. Ter-williger. et al&apos;, calculated saturation profiles which matched those which they observed when gas displaced water vertically downward. Based on their study, Jones-Parra and Calhoun5 roposed a method of computing saturation distributions sufficiently removed in time from the initial conditions so that all saturations in the flood front region were assumed to move with the same velocity. This latter assumption corresponds to the tangent construction on the flowing fraction-vs-satura-tion curve proposed by Welge." A numerical solution to the problem of water displacing oil from a water-wet porous medium was recently presented by Blair, ef at&apos;. The initial conditions included a uniform saturation slightly above interstitial water saturation. that is, the permeability to water ahead of the front was not zero. This appeared to result in a region of slowly rising water saturation ahead of the front, at least for the particular set of relative permeability and capillary pressure data used to illustrate the computation. The authors also postulated an "end-effect" at the outflow face of the system, whereby no water could pass out of the system until the water saturation had built up to a high value. The saturation profiles computed under these assumptions show water accumulating at the downstream end of the system while the flood front proper is still traveling toward the outlet. The purpose of this paper is to present the results of a numerical solution to the one-dimensional water-flooding equation in which no outlet end-effect is considered and where there is no flow of water ahead of the flood front. It should be noted that the contemporary paper of Fayers and Sheldon8 deals with the problem under discussion. For a thorough treatment including both capillarity and gravity the reader is referred to their paper.