Search Documents

By J. A. Younkins. J. P. Proctor, E. D. Hummer

Comparatively little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission Of any effluent Of high ''lid 'content to be rep1aced by 'lean water in Order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the Purpose of this Paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settlillg and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." General Arrangement of Water System So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers,1,2 The washer, which handles o to 4-in, raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. I) consists of twin 48.in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By R. G. Clay, C. F. Seaman

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 05 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to he used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would he available at each shaft for places where there were no regular blasting stations and could he used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

By Arthur A. Center

World production of electrolytic zinc has shown an increase for each year since 1932. Production up to 1936 was summarized in my earlier paper [Trans. A.I.M.E. (1936) 121, 453-4641, and this present paper carries the subject through 1943. During this time of increase, it is safe to say that the average purity has been raised more or less continuously, and the amount of four-nines metal has been in- creased. While the period reflects preparations for and the carrying on of the present war, electrolytic zinc proved its value in many industries as a peacetime metal in the years from 1919 to 1940. World production (Table I) increased from about 594,000 tons in 1936 to around 858,000 tons in 1943; United States production increased from 127,171 tons to 329,903 tons for the same years. Total production of primary zinc in the United States is given in the first column of Table I; retort production of primary zinc, obtained by difference, in the last column. The curves drawn from these figures are shown in Fig. I. They represent continuations of the curves in the earlier paper that cover commercial production of electrolytic zinc from its inception in 1915 to 1935. The earlier paper gave data for total world production and foreign retort production (calculated therefrom) and showed curves of electrolytic vs. retort production

Jan 1, 1944

By M. J. Salkind

In discussing the possible contribution of plastic deformation to neck growth during sintering, Wilson and Shewmon State that Lenel, Ansell, Salkind, and Early34, 35 concluded that dislocation flow is the rate-controlling process in sintering under zero external load. The experiments cited34, 35 were done with applied external loads, and the conclusions were that the same kinetics could be controlling sintering due to the force of gravity with no additional applied load. The effect of gravity on sintering behavior was previously cited.34, 31 In addition, Wilson and Shewmon argue that the conclusions of Refs. 34 and 35 are doubtful because the strain rate is proportional to stress for plastic flow. This assumption is true only for certain kinds of plastic flow such as Nabarro-Herring Microcree38 As Early, Lenel, and Ansell point out3' plastic flow, based upon dislocation movement, can exhibit strain rates which exhibit a power law relationship to the applied stress.39, 40 Wilson and Shewmon also doubt the results of Refs. 34 and 35 because the stresses in the necks are too small for x/a > 0.1. This is true, and the experiments described in Refs. 34 and 35 were done for small values of %/a. The conclusion was that plastic flow by dislocation movement was important during the early stages of sintering when x/a is small.

Jan 1, 1968

By P. K. Guerrero, Nathaniel Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere. This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors, and more recently by Rose. This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically.

Jan 5, 1960

By G. E. Agar

The energy required for dry grinding of phosphate rock in ball and roller mills has been analyzed by the method suggested by Charles and others. The findings are not wholly in agreement with Charles' predictions; but, nevertheless, the method of analysis is shown to be sound. Some of the deviation is probably attributable to the characteristics of a dry grinding system. Many laboratory and pilot plant scale experiments have been made to determine the energy requirements for size reduction. This topic was recently reviewed by Agar and Brown' and it was apparent that very little if any data exists in the literature which permits one to apply the Charles 2-Holmes3 analysis to industrial size systems. More recently, the idea has been put forward that the postulate of comminution by impact used by Charles and others was not sufficient to explain size-reduction throughout the grinding operation. The opportunity exists in the grinding operations of International Minerals and Chemical Corp. (IMC) to analyze the energy-size relationship for dry grinding phosphate rock in both ball and roller mills. This situation arises because the mills are used for custom grinding and make products from 50% to 85% minus 200 mesh. BACKGROUND A correlation of particle size in a comminuted material with the energy expended in size reduction was proposed by charles2 to be of the form

Jan 1, 1965

By Irwin Remson

Some unique hydrogeologic issues are inherent in the problems of siting, designing and licensing a mined geologic high-level nuclear waste repository. The problems involve hydrogeologically unfamiliar rocks for which little proven technology has been developed, long containment periods, elevated temperatures, and externally-imposed management constraints. In evaluating the existing national program, it should be recognized that hydrogeology is only one aspect of the total nuclear waste disposal problem, that the use of multiple barriers requires that the hydrogeologic system be considered in its entirety as a total system, and that engineering modifications can improve the isolation capabilities of certain barriers. Important research questions involve the mechanics of transport through dense fractured and unfractured rocks, methods for measuring vertical hydraulic conductivity, and a variety of geochemical questions. Current expectations for "high quality data" from either in situ or laboratory testing are unrealistic, and a modified approach to repository hydrogeology is needed. The dilemma is that the hydrogeological characteristics that make a potential host rock more satisfactory for respository siting are the same characteristics that are difficult to characterize and make the particular site more difficult to license. Finally, evaluation of the containment potential of any candidate site will become meaningful only with detailed underground exploration, mapping and testing in the host rock formations at the repository levels.

Jan 1, 1984

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel-making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions.

Jan 12, 1950

By Blamey Stevens

The object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all possible cases. The generalizations of observed data, taken from Geikie's Text-Book of Geology, confornl to the laws of intrusion herein stated, and the deductions based upon these lams. No authority, however, is quoted for the type which I hare named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the nrorking of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,' there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By John Henderson

FOR some time now the most commonly accepted description of liquid silicate structure has been the "discrete ion" theory, proposed originally by Bockris and owe.' This theory is that when certain metal oxides and silica are melted together, the continuous three dimensional silica lattice is broken down into large anionic groups, such as sheets, chains, and rings, to form a liquid containing these complex anions and simple cations. Each composition is characterized by "an equilibrium mixture of two or more of the discrete ions",' and increasing metal oxide content causes a decrease in ion size. The implication is, and this implication has received tacit approval from subsequent workers, that these anions are rigid structures and that once formed they are quite stable. The discrete ion theory has been found to fit the results of the great majority of structural studies, but in a few areas it is not entirely satisfactory. For example it does not explain clearly the effect of temperature on melt structure,3 nor does it allow for free oxygen ions over wide composition ranges, the occurrence of which has been postulated to explain sulfur4 and water5 solubility in liquid silicates. In lime-silica-alumina melts the discrete ion theory is even less satisfactory, and in particular the apparent difference in the mechanism of transport of calcium in electrical conduction8 and self-diffusion,' and the mechanism of the self-diffusion of oxygen8 are very difficult to explain on this basis. By looking at melt structure in a slightly different way, however, a model emerges that does not pose these problems. It has been suggested5" that at each composition in a liquid silicate, there is a distribution of anion sizes; thus the dominant anionic species might be Si3,O9 but as well as these anions the melt may contain say sis0:i anions. Decreasing silica content and increasing temperature are said9 to reduce the size of the dominant species. Taking this concept further, it is now suggested that these complexes are not the rigid, stable entities originally envisaged, but rather that they exist on a time-average basis. In this way large groups are continually decaying to smaller groups and small groups reforming to larger groups. The most complete transport data 8-10 available are for a melt containing 40 wt pct CaO, 40 wt pct SiO2, and 20 wt pct Al2O3. Recalculating this composition in terms of ion fractions and bearing in mind the relative sizes of the constituent ions, Table I, it seems reasonable to regard this liquid as almost close packed oxygens, containing the other ions interstitially, in which regions of local order exist. On this basis, all oxygen positions are equivalent and, since an oxygen is always adjacent to other oxygens, its diffusion occurs by successive small movements, in a cooperative manner, in accord with modern liquid theories." Silicon diffusion is much less favorable, firstly because there are fewer positions into which it can move and secondly, because it has the rather rigid restriction that it always tends to be co-ordinated with four oxygens. Silicon self-diffusion is therefore probably best regarded as being effected by the decay and reformation of anionic groups or, in other words, by the redistribution of regions of local order. Calcium self-diffusion should occur more readily than silicon, because its co-ordination requirements are not as stringent, but not as readily as oxygen, because there are fewer positions into which it can move. There is the further restriction that electrical neutrality must be maintained, hence calcium diffusion should be regarded as the process providing for electrical neutrality in the redistribution of regions of local order. That is, silicon and calcium self-diffusion occur, basically, by the same process. Aluminum self-diffusivity should be somewhere between calcium and silicon because, for reasons discussed elsewhere,' part of the aluminum is equivalent to calcium and part equivalent to silicon. Consider now self-diffusion as a rate process. The simplest equation is: D = Do exp (-E/RT) [I] This equation can be restated in much more explicit forms but neither the accuracy of the available data, nor the present state of knowledge of rate theory as applied to liquids justifies any degree of sophistication. Nevertheless the terms of Eq. [I] do have significance;12 Do is related, however loose this relationship may be, to the frequency with which reacting species are in favorable positions to diffuse, and E is an indication of the energy barrier that must be overcome to allow diffusion to proceed. For the 40 wt pct CaO, 40 wt pct SiO2, 20 wt pct Al2O3, melt, the apparent activation energies for self-diffusion of calcium, silicon, and aluminum are not significantly different from 70 kcal per mole of diffusate,' in agreement with the postulate that these elements diffuse by the same process. For oxygen self-diffusion E is about 85 kcal per mole,' again in agreement with the idea that oxygen is transported,

Jan 1, 1963

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.' Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.'' As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By Gerhard Bockstiegel

Kuczynski's formula has been derived for the case of nonspherical particles. TWO formulae of Kuczynski's type have been derived, one describing the increase in tensile strength, the other describing the progress of shrinkage of a powder compact. It has been strength,shown that the exponents of all three formulae each contain two magnitudes of different physical characters, viz, the geometrical factor a and the kinetic factor ß. The interrelationships between the three exponents are stated. SOME years ago Kuczynski1 experimentally showed that the radius, x, of the area of contact between very small spherical metal particles and a metallic block is related to the time of sintering, t, by the following equation x = constant tk [11 where k has the value 1/5 or 1/7. Assuming that the metal particles were perfect spheres and the metallic block was perfectly flat, he derived the foregoing equation from theoretical considerations of the process of material transport in metals, and he showed that exponent k is different for different mechanisms of transport, e.g., k = 1/2 for viscous flow (according to Frenkel2), k = 1/3 for evaporation and condensation, k = 1/5 for volume diffusion, and k = 1/7 for surface diffusion. From this Kuczynski concluded that the mechanism of transport was either volume diffusion or surface diffusion, depending on whether the value of k, as found in his experiments, was 1/5 or 1/7. Subsequently. Cabrera8 corrected Kuczynski's calculations with regard to surface diffusion, showing that the theoretical value of exponent k is 1/5 for both volume and surface diffusion. He supposed that the different experimental values of k were due to slight differences in the shape of the metal particles. An exponential relationship similar to the aforementioned was found by Okamura, Masuda, and Kikuta,4 Masuda and Kikuta, and Takasaki8 when studying the rate of shrinkage on powder compacts during sintering. The authors measured the shrinkage by means of the fraction w = Vp — V./Vp — V,,,, where V,, is the volume of the green compact, V, is the volume of the sintered compact, and V,,, is the volume of the compact in its densest state. This fraction, w, they found, is related to the time of sintering, t, by the equation w == constant tm. [21 Further, Bockstiegel, Masing, and Zapf7 observed that the tensile strength, s, of sintering iron powder compacts can also be related to the time of sintering, t, by an equation of the foregoing type, i.e., s = constant tn. [3] For exponent n the values 0.28 (S=2/7) and 0.35 ( 2/5) were obtained, and the authors pointed out that there might exist a simple interrelation between exponent n as found in their experiments and exponent k in Kuczynski's equation. The authors supposed that 2k = n, since the strength of adhesion between a metal sphere and a block (as in Kuczyn-ski's experiments) must approximately be proportional to their contact area, p. x2. Theoretical Considerations This paper is an attempt to correlate the fundamental experiments of Kuczynski's type with the results obtained with powder compacts as represented by Egs. 2 and 3. In particular, the paper is to show how the rate of sintering is influenced by the geometry of the sintering particles and by the type of material transport. As the geometry of particles conglomerating in a powder compact is very complex, some simplifying assumption has to be made, of course, in order to adapt the problem to mathematical treatment. In the following paragraph a suitable simplification is introduced, and Kuczynski's formula is derived for the case of nonsphcrical particles. Relation Between Area of Contact and Sintering Time—As the face of contact between two particles in a sintering powder compact is not necessarily a circle (as in the case of spheres sintering to a block), Kuczynski's formula is modified as follows: Let the perimeter of the face of contact be described by means of polar coordinates R, 4, as shown in Fig. la, so the area of contact, f, is determined by f= 1/2 . S112p[R(Æ) ]2 dÆ [4] Then, let the two particles be intersected by a plane perpendicular to area f. The intersection is shown in Fig. lb. According to the nomenclature in this figure, the distance, h, between the surfaces of the two particles is a function of T and Æ: h = h(r,Æ). For the particular case of spherical particles, as in Kuczynski's theory, this function becomes: h = constant r2. It shall be assumed here that in the close neighborhood of their

Jan 1, 1957

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don't use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By J. J. Frawley, W. J. Childs, W. R. Maurer

The object of this investigation was to determine the growth habit of bismuth and bisrrtuth alloy dendrites as a function of supercooling. To do this, techniques were developed to increase the amount of supercooling in bismuth and bismuth alloys. For pure bismuth, the growth habit was dependent on the amount of supercooling. At low amounts of supercooling, about 10" C, prismatic dendrites were obtained. With increased supercooling, about 20 C, a hopper growth habit was observed. In many cases where hopper growth had occurred, the hopper dendrites were twinned during the growth process. This twinned surface enable prismatic dendrites to nucleate and grow by a twin plane mechanism. When the amount of supercooling was increased to about 25 °C, the growth habit was a triplanar growth. With still greater supercooling, about 3s°C, a branched growth habit occurred. The exposed planes on the prismatic, hopper,, triplane, and branched dendrites have been determined. The growth habit of the dendrites which grew along the crucible wall was found to have the (111) as the exposed plane, with <211> growth direction. It is apparent that dendritic growth of a metal is dependent on its purity and the solidification variables present. One of the solidification variables is the degree of supercooling. Supercooling, although often observed, has not been studied extensively until recent years. For dendritic growth to occur in a pure metal, the metal must be thermally supercooled. After the dendrites grow into the supercooled melt, the heat of solidification raises the temperature of the specimen to the melting point of the material and the remaining liquid will solidify at this temperature. Decanting is the removal of this remaining liquid before complete solidification. This removal of the remaining liquid after recalescence had occurred is a great aid in the study of dendritic growth. In this investigation, decanting was accomplished by a vacuum-decanting technique . Other investigators1-5 have studied the growth characteristics of various low-melting-temperature pure metals and alloys as a function of supercooling. However, large degrees of supercooling were not included. For their study of dendritic growth of lead, Weinberg and chalmersl employed a decanting technique which was achieved by pouring off the remaining liquid, exposing the solid/liquid interface. This method was employed later by Weinberg and Chalmers2 for the investigation of tin and zinc dendrites. The method for obtaining a solid/liquid interface was improved by Chalmers and Elbaum. They employed a triggered spring which was attached to the solidifying section of the specimen. Upon activation, the spring jerked the solid interface away from the liquid melt. In the study of growth from the supercooled state, a metal of low melting point which exhibited a high degree of supercooling was desired. Bismuth gave very consistent supercooling when a stannous chloride flux was employed. The maximum supercooling obtained was 91°C, with an average supercooling of between 65" and 75°C. The consistency of supercooling greater than 50°C was very high. The use of vacuum to aid in the rapid decanting of molten metal has proven to be very successful in this investigation. The vacuum gives a rapid decantation, usually leaving the solidified metal structure sharply defined. The purpose of this investigation was to study the effects of supercooling and the effects of alloy additions on the growth habit of bismuth dendrites. The structure of bismuth has been variously defined as face-centered rhombohedral, primitive rhombohedral, and hexagonal. However, bismuth has only one plane with threefold symmetry, the (111) plane, and the crystal-lographic structure is considered a 3kn structure. MATERIALS The bismuth which was employed in this investigation was obtained from the American Smelting and Refining Co. of South Plainfield, N. J. The accompanying spectrographic analysis data indicated the bismuth to be 99.999+ pct pure. The tin was obtained from the Vulcan Materials Co., Vulcan Detinning Division, Sewaren, N. J. It was classified as "extra pure". Nominal analysis was 99.999+pct. In order to prevent contamination of the bismuth melt from the atmosphere, an anhydrous stannous chloride (Fisher certified reagent grade) was added to each melt. The fluxing action obtained from the use of the chloride provided a large amount of supercooling in the specimen. APPARATUS A 30-kw, 10,000-cps motor-generator set, connected to a 6+-in.-diam air induction coil, was employed to melt and superheat the specimens. The temperatures were recorded by means of a chromel-alumel thermocouple and a potentiometric recorder. The thermocouples were 0.003 in. in diam, and were encapsulated with Pyrex glass to prevent the thermocouple from acting as a nucleating agent and also from contaminating the melt. Fig. 1 illustrates the vacuum-decanting apparatus when a liquid flux was employed. A standard 30-ml Pyrex beaker was placed on top of an asbestos insulating block. A 5-mm-ID Pyrex tube with aA-in. spacer tip attached to its end was used for the decanting tube. The spacer tip contributed significantly to a successful decanting operation. The tip located the opening of the decanting tube about -^ in. from the bottom of the

Jan 1, 1969

By W. L. Phillips

Stress-strain curves were obtained for single crystals of 70 pct Ag-30 pct Zn tested in tension and shear. Samples tested in tension and shear had comparable resolved shear stresses and stress-strain curves. The {111} <110> slip system was observed. It zoas found that the9.e is a barrier to slip in both latent close -packed directions and that the magnitude of these barriers is proportional to prior strain during easy glide. It was observed that cross-slip in tension and shear was most frequent in crystals with an initial orientation near <100> "Oershoot" zoas observed in tension. The amount of this "overshoot" was independent of initial orientation. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of easy glide which is characterized by a linear stress-strain curve and a low coefficient, d/dy, of work hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In fcc metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close packed planes, is the existence of latent slip planes in the fcc crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.ls Several theories have been proposed to explain the linear hardening and parabolic stages of the stress -strain curve.6"10 The easy-glide region is the least understood of the three stages. The stress-strain characteristics of Cu-Zn, which shows a long easy-glide region, have been extensively investigated."-" In light of recent ideas on dislocations, cross-slip, effect of solute atoms, and stacking fault energy, it was felt that the certain features of this earlier work might be compared with another alloy, Ag-30 pct Zn, which also exhibits a long easy-glide region. Tension and shear stress at room temperatures were employed. The results obtained, together with some interpretation of the observations, are described below. EXPERIMENTAL PROCEDURE The silver and zinc used for mixing the alloys were 99.99 pct pure. The two components were weighed to within 0.1 pct of the weights required fo the alloy composition. They were then placed in a closed graphite mold and the mold and contents were heated in 100°C stages from 500&apos; to 900°C with sufficient time and vigorous agitation at each stage provided to dissolve the silver. The crucible was then heated to 1150°C and agitated violently before being quenched in oil. The resulting alloy rod was machined free of sur face defects and then placed in a graphite mold designed for growing single crystals. The graphite mold was closed with a graphite plug and was encased in a pyrex glass tube which was connected to a vacuum system. The tube and mold assembly were placed in a furnace; the tube was evacuated and the furnace was rapidly heated to a temperature sufficient for fusing and sealing the glass. The glass-encased evacuated mold and contents were then lowered through a vertical furnace. The top section of the furnace was held at 100 °C above the melting point of the alloy. The lowering rate was 1.5 in. per hr. The tension specimens were 1/4 in. diam; the shear specimens were 1/2 in. diam. These specimens were then removed from the mold, etched, and chemically polished with hot (60°C) Chase etch reagent (Crz03-4.0 g, NH4C1-7.5 g, NHOs-150 cc, HzS04-52 cc, and Hz0 to make 1 liter). In preparation for tensile testing, the specimens were carefully machined to a diameter of about 0.200 in. to permit a gage length of 6 in., annealed for 16 hr at 800&apos; to reduce coring, and then cleaned and polished. A modified Bausch-type shear apparatus which has been described previously18 were employed. The gage length was 1/8 in. This shear apparatus was placed in an Instron tensile testing machine. EXPERIMENTAL RESULTS A) Tension. Several specimens were extended at room temperature to determine the effect of initial orientation on the stress-strain curves of Ag-30 pct Zn. The initial orientation and the resolved shear stress supported by the active slip system at various total strains are plotted in Fig. 1. The critical resolved shear stress, t,, initial rate of work hardening, d/dy, and length of the easy-glide region are independent of orientation. The arrival at the symmetry line is shown by an arrow in Fig. 1. During the easy-glide region of the stress-strain

Jan 1, 1963