Search Documents

By D. C. Hilty, W. Crafts

J. Chipman—It has been my privilege to discuss this work with the authors on several occasions and to observe at first hand the experimental methods employed. I wish, therefore, to emphasize certain points which they have mentioned only briefly with regard to the experimental techniques. The rotating induction furnace as here employed interposes liquid metal between slag and refractory thus preventing the two nonmetallic parts of the system from reaching equilibrium with one another. It is therefore impossible for the metallic phase to be completely in equilibrium with both the slag and the crucible. The metal also acts as a partially permeable membrane allowing certain components, including oxygen, to diffuse from slag to crucible. This transfer results in building up on the face of the crucible a layer of material whose composition is in part dependent on that of the bath. Reactions between the layer and the solid refractory are slow, as evidenced by the rather good life of the crucible. Hence it seems probable that the layer is more nearly in equilibrium with the metal than with the underlying crucible material and that, once it is established under a bath of a given composition, its further reactions with that bath are slow. Additions to slag or bath may be followed by changes in the layer; and time must be allowed for virtual completion of such changes, before it can be assumed that slag and metal are in equilibrium. We may judge from the results reported that, in general, this was the case and that the data represent at least quite close approximations to slag-metal equilibrium. Data on deoxidation and on oxygen solubility are no better than the analytical methods employed. The vacuum fusion method as used by the authors seems entirely adequate for the samples analyzed. I have had frequent occasion to compare results with their laboratory, always with very satisfactory agreement. The determination of aluminum at very low concentrations is perhaps an even more difficult procedure. Here also the colorimetric method used has been worked out with great care and is undoubtedly the most dependable method available. The discrepancy between observed and calculated deoxidation or solubility lines is not to be explained as the result of experimental errors, either in the sampling or analysis of the metal. Nor is it to be blamed upon inaccuracies in the several kinds of indirect data upon which the calculated results were based. It is true that both the observed and the calculated lines admit of some uncertainty as to their exact locations, but the uncertainties are small compared to the wide gap which separates the two lines. The authors have pointed out the real cause of the discrepancy. In all of their experiments the solid phase was not Al2O3 but a mixed oxide containing iron and aluminum. This suggests an extension of the calculated values to include equilibrium with the spinel FeO . A12O3. The free energies of FeO and A12O3 are known, that of the spinel is not. However, it cannot differ greatly from that of its component oxides for even in the more stable spinel, chromite, the free energy of formation from the oxides is less than 10,000 cal. For purposes of calculation we shall call this free energy X and solve for values of X lying between zero and 10,000 cal. The other data required are taken from the forthcoming revision of "Basic Open Hearth Steelmaking" and are given in the following equations in which underlined symbols indicate elements dissolved in liquid steel and the standard concentrations are 1 pct. ?F° at 1600°C, cal ?LA = 2 Al + 3 O; + 107,200 FeO = Fe + 0; + 5,460 FeO + A12O3 = Fe + 2A1 + 4 0; + 112,660 — X The corresponding equilibrium concentrations are shown in fig. 21. The line marked A12O3 corresponds to the first equation, those marked FeO . AL2O3 correspond to the last, with X = 0, 5000 and 10,000 cal, respectively. The two upper lines represent the data of Hilty and Crafts and of Wentrup and Hieber. The points are the observations of Hilty and Crafts in the presence of 0.50 pct Mn.

Jan 1, 1951

By E. S. Anolick, Joseph Singer

The magnetic after-effect, in the form of time decay of permeability (l/µ), has been used to obtain independent data on the solubility of' carbon in pure iron. The results differ slightly from the solubilities obtained through internal -friction experiments. The mechanism of the time decay being the magnetic analogue of internal friction, it appears necessary to explain the observed discrepancies, and some suggestions are made. THE purpose of this work was to establish the reliability of the time decay of permeability as a measure of dissolved interstitial in the body-centered-cubic lattice, and further, to establish techniques suitable for such measurements with samples of a form convenient for various other measurements. This particular sample form was the "epstein" strip, i.e., 25 cm by 3 cm by 0.035 cms. While the general conclusions are not limited by this geometry, there are two aspects of the samples that may be relevant: a) texture, and b) grain size, which ranged generally from 1 to 10 mm. Effects due to these two possible parameters were thought to be small and were not investigated. Calibrating the time decay technique and the other experimental procedures by measuring the solubility of carbon in pure iron suggested itself because of the accumulation of data on this subject through the related technique of the internal friction'; The essentials of this report have been published in a somewhat condensed form.5 Since then some additional data have been taken. It is the purpose of this paper to add these data and to provide more complete description of the experimental techniques than was possible then. The time decay of permeability is a form of the magnetic after-effect.6,7 Permeability is measured immediately after demagnetization (µº) and also long after (µ8). The time decay, ?(l/µ), is the difference 1/µ8 - 1/µ0 and has been considered to be proportional to the concentration of a dissolved interstitial6,8,9,12 The relaxation time! 7, is characteristic of a particular diffusion, and affects the permeability as follows: where he being the activation energy for diffusion of the interstitial. Reference is made to the works of snoek6 and Neel7 for a complete discussion. A brief exposition of the principal ideas may be in order here, as follows. On the basis of the simplest model, resistance against domain wall motion increases with time after demagnetization due to the diffusion of interstitials to preferred sites created by the magnetostrictive tetragonolization under the strong magnetic field. Thus permeability, measured with a small field after the abrupt removal of the large field, will continuously fall with the process of diffusion of the interstitials, and the total "time decay" (or "time decrease") should be proportional to the amount of interstitial in solid solution. In the present report, use is made only of the total time decay rather than of the nature of the progress of the decay; the only problem involved in this approach is the need for assurance that only one interstitial is contributing to the effect as used. It is felt that the special use made here of the total time decay warrants the conclusions. Other work has been going on elsewhere on the detailed study of the nature of the time decay.8'9 EXPERIMENTAL A) Materials—12-lb ingots were made in a vacuum furnace from high-purity iron and by a series of hot and warm reductions were brought down to 14-mil strip. This was cut into 25-cm epsteins. The pure iron was decarburized at 750 °C by hydrogen. The time decay measurement for the decarburized iron (see below) indicated a satisfactorily low starting level of interstitials. Grain growth to grain sizes of 1 to 10 mm was produced in the pure iron by a 700" anneal in hydrogen after a critical reduction of about 7 pct as suggested by previous trials. No measurement of texture in the pure iron was made. The grain size was taken to be large enough to be beyond any sharply critical size regarding solubility. B) Infusion of Carbon—Since the permeability measurement required about two dozen epsteins, a special method of carbon infusion had to be developed to ensure homogeneity of infused carbon. This was accomplished by setting the samples edgewise in a

Jan 1, 1961

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By W. A. Jr. Slippy, E. P. Dahlberg, R. B. Reed-Hill

A large room-temperature mechanical-hysteresis effect under cyclic tensile loading was observed in zivconium specimens prestrained at 77°K so as to form large numbers of (1121) twins. The observed hysteresis loss was a maximum when the prestrain was just under 1 pct It also depended strongly on the maximum applied cyclic stress, but only moderately on loading rate and temperature (-72°to 100°C). The phenotnena have also been studied in terms of the elastic aftereffect where the data has been found to cotlforln closely to the functional relationship between strain and time, c = -RT/a In tank ft. t to)/Zr, for strains cts large as about 10-4 This eyication can be derived directly from the strain-rate equation There may be important commercial implications to the present discovery since it appears that within rather wide limits it may be possible to obtain any desired magnitude of damping capacity in zirconium melal. The damping propevties may also be given directional characteristics. It is shown that the observed anelaslic phenomena can he explained on the assumiplion that they are the resuilt of stress-induced twin-boundary movements in which the average twin increases its thickness by only a few percent. In polycrystalline zirconium, a grain is least favorably oriented for slip when its basal plane, containing the (1130) slip directions, lies nearly perpendicular to the principle normal stress. Mechanical twinning is favored by this orientation and under simple tensile deformation at room temperature the primary twinning mode is {1012).' The (1012) twinning shear is small (0.17) so that, during deformation, twin growth does not greatly enhance ductility. At 77°K, on the other hand, the predominant twinning mode shifts to {1121), and many thin (1121) twins can form at small strains.' Twins thus nucleated can grow readily during subsequent room-temperature deformation and permit easy deformation in unfavorably oriented grains. In addition, the (1131) twinning shear is large: 0.63. These facts have lead to a process' for greatly improving the room-temperature ductility of zirconium when it contains a sizable fraction of grains with basal planes nearly normal to the stress axis. Optimum results are obtained by slightly less than 1 pct prestrain. The effect is large so that a 50 pct elongation increase is readily attained. A large room-temperature mechanical-hysteresis effect has also been observed in zirconium specimens prestrained at 77°K. The present paper is concerned with some aspects of this effect which the experimental observations strongly indicate is primarily the result of strain-induced {1121) twin-boundary movements. This clearly suggests that mechanical twins formed by plastic deformation can cause anelastic effects similar to those previously observed2 for annealing twins and twins associated with phase transformations. EXPERIMENTAL PROCEDURES All specimens were prepared from arc-melted sponge zirconium plate stock as previously described,3 which has a preferred orientation with basal planes aligned parallel to and uniformly distributed around the rolling direction. Both lonti-tudinal and transverse tensile specimens, with axes parallel and transverse, respectively, to the plate rolling direction, were cut from this plate. In a longitudinal specimen most grains are favorably oriented for slip, while in a transverse specimen a large fraction are unfavorably oriented. Prestraining at 77°K was performed in two ways. In one, annealed zirconium plate stock was cooled in liquid nitrogen and then rolled in the transverse plate direction to strains varying from 0.5 to 12 pct. Cylindrical 1/8-in.-diameter by 1-1/4-in.-gage-length tensile specimens were machined from this material. In the other, previously machined tensile specimens were prestrained in tension at 77°K between 0.2 and 3.8 pct. Type FA 25-12 SR4 strain gages were cemented to all specimen gage sections. All tests were performed on an Instron testing machine of 10,000-lb capacity. EXPERIMENTAL RESULTS Fig. 1 shows a typical two-cycle room-temperature stress-strain diagram for a specimen prestrained 0.65 pct by rolling at 77°K. The maximum stress in both cycles was 14,500 psi. Note that in the first cycle the loading and unloading curves are unsymmetrical so that a residual strain, er, remains after unloading. In the second cycle the stress-strain curves form a nearly symmetrical hystere-

Jan 1, 1965

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By Y. C. Liu, G. A. Alers

Using X-ray pole-figure information and the single-crystal elastic constants, the angular variation of an elastic modulus in a polycrystal can be calculated and compared to measured clalues. This procedure has been used in the past to provide supporting ecidence for a particular choice of ideal orientations in the description o the X-ray pole figure. Since it is well-known that the absolute value oj an elastic modlus oj a poly crystal cannot be acczrralely calculated from the single-crystal elastic constants, there exists a serious question about the reliability oj this modulus method in the study of textures. This paper deriz-es sez3eral simple fornzulae for the ntzgular lariatiion of Young's modulus in the plane o a rolled sheet sing the same ssuinptions which lead to the lack oj detinztion of the absolute c'alre OJ the elastic ,nodulus. The vesults show that, although the absolute isallre oj Young's modulus depends strongly on the assumptions made, the shape of the modulus vs angle curve is not very sensitive to the assumptions and thus can be used reliably in texture studies. Exatzples oj' using this criteriotz are illustrated in the text. NeARLY all poly crystalline materials have some preferred orientation in the arrangement of their grains and hence exhibit anisotropy in their properties. This preferred orientation is usually measured and studied by X-rays which yield detailed information on the statistical distribution of grain orientations in the form of pole figures. The usefulness of these pole figures in theories of texture formation and in predictions of properties has come to depend almost entirely on the characterization of the pole figure by one or more ideal orientations. Unfortunately, this characterization is not unique and different authors often present different ideal orientations to characterize a given pole figure. In order to distinguish between these different choices of ideal orientations, it is necessary to go beyond X-rays and consider other physical properties which reflect the texture' simply because any choice of ideal orientations must predict correctly the observed anisotropy in all physical properties. The most common example of this procedure has made use of the angular variation of Young's modulus with respect to the rolling direction in the plane of a rolled sheet.3 4 Here the anisotropy can be measured easily and it can also be calculated from the single-crystal elastic constants and the chosen ideal orientation. Unfortunately the methods used to calculate this anisotropy were chosen for their simplicity rather than for their mathematical rigor so that there exists a serious question as to the validity of conclusions reached by this modulus method. It is well-known5 that the absolute value of the Young's modulus of a polycrystalline aggregate cannot be calculated very accurately because different mathematical averages over the grains yield different results. It is one purpose of this paper to examine the effect of different averaging procedures on the calculated anisotropy of Young's modulus in the rolling plane of rolled sheets in order to see if this property can be used reliably in texture studies. This particular modulus and type of material were chosen because the modulus is easily measured and rolled sheet is technologically important. The results show that, although different averages yield different absolute values for Young's modulus, the shape of the modulus vs angle curve is not very sensitive to the averaging procedure and thus can be used as a criterion to check the various ideal orientations used to characterize the X-ray pole figure. Examples of this checking procedure are given in the final section. Another purpose of this paper is to examine the possibility of using the anisotropy of Young's modulus as an indicator of texture without reference to pole figures or ideal orientations. Such a use would require that different textures yield quite different shapes for the modulus vs angle curve so that the distinction between textures would be quite clear. The experimental results presented in the final section indicate that there is easily enough variation in shapes to allow modulus measurements to be useful texture indicators, par-

Jan 1, 1967

By F. C. Holman

It is desired in these notes to record a vein-phenomenon certainly unique in the writer's limited experience, and, as it seems to him, sufficiently rare to be worthy of mention. In the little mining camp of Forbestown, situated in the Sierra Nevada of California, it was announced one day, when the miners of the Cold Banks mine came off shift, that "washed gravel" had been struck on the 265-foot level. To those acquainted with that section and the character of the mine (a gold-bearing quartz-vein) this was a somewhat startling announcement; for, prolific as the State is, we are not in the habit of mixing up promiscuously our vein- and placer-deposits. However, the statement proved to have some foundation. The mine is located at an altitude of about 2700 feet, on the brink of one of the great canyons of erosion characteristic of the drainage of this range. A lateral ravine cuts the vein at right angles, thus making its general strike approximately parallel to the canyon at this point, and with a variable dip of from 20 to 40 degrees towards the canyon. The strong, well-defined vein, often 20 feet wide and more, presents nothing to distinguish it particularly from scores of others in the State, unless if be considered peculiar in the highly crystalline character of its quartz and the nature of the enclosing country-rock, which is metamorphic in the extreme, very hard, devoid of lamination, and in bedding so obscure that it might easily pass—at least on superficial examination—for one of the basic eruptives. Near by in the district can be found a series of slates common to the gold-belt of this range, and within the limit of the company's property is an intrusion of an acid eruptive. On an adjoining claim a granite shows itself. The mine is opened through an inclined shaft sunk on the vein. The ore carries both free gold and sulphurets, the greater part of its value

Jan 1, 1896

By Carl Henrich

Aspen, the flourishing mountain- and mining-town of Pitkin county, Colorado, is located in the valley of the Roaring Fork, 11 miles above Glenwood springs, where that stream empties its waters into Grand river, a tributary of the Colorado. The Roaring Fork heads on the western slope of the Sawatch range near Grizzly peak, and runs in a general northwesterly direction to its junction with the Grand river. Of its numerous tributaries, Castle creek joins it just below the town of Aspen, the town being built on an extensive flat hounded on the northeast by the Roaring Fork and on the west by Castle creek. The latter heads at the junction of the Sawatch and the Elk mountains and flows northward between the two chains, until it empties into Roaring Fork. Opposite the town of Aspen, Hunter creek, coming westward from the western slope of Mount Massive, joins the Roaring Fork. About a mile north of Aspen, the bed of Hunter creek is at least 300 feet higher than that of the Roaring Fork at Aspen. Hunter creek forms thus, at its mouth, one of the best water-powers in Colorado. A portion of it is now utilized for electric lighting in Aspen, while in the near future, the whole of this magnificent natural power will be applied, through electric transmission, for hoisting, pumping and ventilating at different mines of the district. The mountain opposite the town of Aspen, on the east side of Hunter creek (which near its mouth flows southerly), is called Smuggler mountain, from the famous mine at the foot of it. On the other, or western, side of Hunter's creek (see map, Fig. I), a higher mountain rises, on the slope of which the regular dip of the Triassie or Upper Carboniferous red sandstone strata, alternating with white layers of the same rock, can be clearly seen from town. This mountain is called Red mountain, from the prevailing color of its rocky

Jan 1, 1889

By Willard S. Morse

Referring to Mr. Rickard's paper on " The Limitations of the Gold Stamp-Mill" (Trans., xxiii., 137), and the discussions that have followed, and without entering into any controversy as to the relative merits of the " California " and " Colorado " types of stamp-mills, I wish to give the results obtained on ores from Lynx Creek district, near Prescott, Arizona, with a stampmill of the Colorado, or, more precisely, the Gilpin county, Colo., type. The mines of the district have been worked for nearly thirty

Jan 1, 1896

By A. S. C. Owili-eger

Coal mining is one of the major activities that may affect the natural or existing hydrologic equilibrium of a basin. Consequently, the mining industry is committed to the conservation and protection of the hydrologic balance within and around mining environments. This commitment embodies thorough and careful consideration of the quantitative and qualitative variations and, in general terms, the environmental impacts of mining activity on the natural water systems. A research program was undertaken to study the impacts of full extraction coal mining on the ground water systems at one of the coal basins in the Appalachian region. The primary objective was to provide reliable information for determining the local and possibly the regional effects of longwall mining on well yields, and the hydraulic and hydrogeochemical parameters of the immediate surface and subsurface water resources.

Jan 1, 1985

By Carle Hayward

AT THE February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500° it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. cooperated by furnishing the steel and turning the tensile specimens.

Jan 1, 1922

By G. Purcell, S. C. Sun

The objective of the present study was to detennine the role played by double bonds in the flotation of a very pure mineral using 18-carbon unsaturated fatty acids as collectors. Streaming potential measurements were made on a plug of pure synthetic rutile in solutions of inorganic electrolytes and unsaturated 18-carbon fatty acid soaps. Experimental results from these tests are detailed in the paper. The collector effectiveness of oleic acid with one double bond, linoleic acid with two double bonds, and linolenic acid with three double bonds has been a matter of speculation for many years, and conflic- ting experimental evidence1-8 has not clarified the issue. The overall objective of the present study was to determine the role played by double bonds in the flotation of a very pure mineral using 18-carbon un-saturated fatty acids as collectors. Since zeta potential is dependent on adsorption and orientation of ions at the solid-liquid interface, its variation under different conditions of pH and collector concentration should throw some light on the behavior of unsatu-rated fatty acids in flotation pulps. Titanium dioxide, in the form of rutile, was chosen for the investigation because it is now available in a very pure, synthetic, crystalline state, and despite the fact that it is one of the most important synthetic inorganic chemicals in commercial use, its electro-kinetic properties have not been closely studied. Electrokinetic properties of rutile in various aqueous solutions are discussed in this paper. Adsorption information gained from the streaming potential measurements enabled the flotation resultsg to be explained in a qualitative way, thus providing a clearer

Jan 1, 1963

By John F. Abel

A good mining engineer is supposed to make a good mine. What then makes a good mining engineer? There certainly are a lot of answers to that question. The answers depend on whether you are one, work for one, or employ one. There are several cliches about mining engineers, and there is some truth in them-as there usually is in any stereotype. Hollywood chose Jeff Chandler to portray a mining engineer in Foxfire. The image here was of an almost one-man mining operation. When Chandler picked up a jackhammer, cradled it in his gut and started drilling out a tunnel round, it gave one the hives. I would have liked to see him finish just one round that way. There are limits to what even the most hairy-chested of us will try. We can assume that Hollywood feels it needs to over- draw any profession to add impact.

Jan 1, 1970

By E. Klar, A. B. Michael

Differences in the electrical conductivities of copper powder sintered under reducing, selectively oxidizing, and neutral atmospheres are related to impurities in solution or as precipitated oxides. The precipitation of impurities as oxides during sintering in nitrogen is proposed for maximizing the conductivity of sintered copper. Conductivity equations for two-phase systems are summarized. Selected equations are applied to porous sintered copper and composite structures. A recent review of the influence of impurities on the electrical conductivity of copper by Gregory et al.1 emphasized that an impurity in solid solution has a much more pronounced effect on reducing the electrical conductivity than when present partly or wholly as a second phase. When impurities in solid solution can be precipitated as oxides, the copper is purified with respect to these elements and the conductivity is increased. Cast and wrought copper, therefore, frequently contain an intentional residual oxygen concentration to oxidize and precipitate impurities less noble than copper. Copper powders generally also contain impurities which can contribute to a reduction in the electrical conductivity of the sintered material. The most deleterious impurities commonly found in commercial copper powders which markedly decrease the electrical conductivity when in solid solution but which can be precipitated as oxides include iron, tin, antimony, arsenic, cobalt, and nickel. In addition to impurities, porosity in sintered copper also contributes to a reduction in the electrical conductivity. The work reported herein discusses the influence of impurities, sintering atmospheres, and porosity on the electrical conductivity of sintered copper. These are important factors for controlling the electrical conductivity of materials such as sintered copper electrical contacts. Several publications on the electrical conductivity of sintered copper and composite materials with random pores or obstacles have incorrectly considered the conductivity to be proportional to the volume fraction of conducting material. However, analyses and equations have been proposed, the earliest of which is perhaps Lord Raleigh's of 1892,' which more accurately describe the conductivity of two-phase systems. These equations which in many cases allow one to closely estimate the electrical conductivity of porous sintered materials and two-phase composites will be reviewed and related to the measured electrical conductivity of sintered copper, copper-graphite. and Ag-W composites. INFLUENCE OF IMPURITIES AND OXIDIZING, REDUCING, AND NEUTRAL ATMOSPHERES Zone-Melted and Leveled Copper. The electrical conductivities of an electrolytic copper and a lower-purity compacting grade of copper powder after consecutive treatments in reducing or selectively oxidizing atmospheres are compared in Fig. 1. The powder and drillings from the electrolytic copper ingot were melted and solidified in a graphite crucible under hydrogen. The vertical zone leveling technique of multiple passes in opposite directions was used to obtain a uniform distribution of impurities. The electrical conductivity was measured on machined specimens 3 by 0.10 in. diam of the zone-leveled material and after the same specimens were consecutively treated as follows: 1) heating in hydrogen at 1600°F for 3 hr; 2) heating in air in a sealed tube so that 0.04 pct 0 was introduced; heating was started at 1000°F for 1 hr and continued at 1800°F for 8 hr; the stepwise diffusion treatment was used to avoid loss of copper due to evaporation of copper oxide at higher temperatures; and 3) final heating in hydrogen at 1600°F for 3 hr. A L&N Kelvin Bridge, type 4306, and a test fixture with knife edges 2 in. apart were used to measure the room-temperature conductivity with an estimated accuracy of ±0.5 pct. In all cases the conductivity of the electrolytic copper was approximately 100 pct of IACS. The conductivity of the impure copper was 80 pct of IACS both in the cast state and after heating in hydrogen. However, after the heating in air, the conductivity of the impure material was 100 pct IACS. After again heating in hydrogen, the electrical conductivity decreased to 60 pct of IACS. This decrease is attributed both to the dissolution of impurities and observed intergranular cracks due to the phenomenon of hydrogen embrittle-ment in copper. These data show that the electrical conductivity of commercial copper as represented by a compacting type powder can be increased significantly by the precipitation of impurities as oxides through heat treatment in an oxidizing atmosphere. Sintered Copper Powder. A commercial compacting type of copper powder pressed to various densities was sintered either in nitrogen, dissociated ammonia, or dissociated ammonia followed by a selectively oxidizing atmosphere of air in sealed Vycor tubes so that 0.06 pct O was added to the material. The electrical conductivity was measured perpendicular to the pressing direction on as-sintered specimens of approximately 3 by 0.25 by 0.15 in. The fully dense material was obtained by zone melting and leveling

Jan 1, 1969

By W. K. Godfrey

The highest compressive strength cement has the highest bond strength in tests in which the cement is subjected to a confining pressure. After perforating, the bond strength is reduced to nearly zero when the pipe is supported by weak cement. Perforating does not affect the bond strength, however, when the pipe is supported by strong cement. Pipe supported by weak cement is damaged by perforating with expendable capsule jets, but is not damaged by perforating with the hollow carrier gun. High strength cements are recommended for oil wells that are to be perforated. Introduction The purpose of this work is to determine the effect of jet perforating on the bonding strength of oilwell cement at simulated down-hole conditions. Bond strength is a good criterion for determining the effectiveness of cement in performing its main function, i.e., that of isolating zones. According to the literature on the subject, the optimum cement strength for perforating is low and should not exceed 2,000 psi compressive strength. This conclusion was based on the appearance of bullet and jet perforations in neat and gel cements largely done in the absence of a confining pressure more than 15 years ago. Discussion Literature A relatively weak cement has been recommended in the literature as having optimum properties for perforating. In 1947, Oliphant and Farris tested bullet perforating of neat cements at various curing times.' Some of the tests were made at down-hole conditions. They reported that the optimum cement strength for perforating was about 2,000 psi compressive strength. Enlarged holes occurred when strength was too low, and the cement shattered and cracked when the strength was too high. In 1951, Morgan and Dumbauld tested bullet and jet perforating of neat and gel cements at surface conditions.' They reported that optimum cement has a compressive strength less than 2,000 psi. In their tests at atmospheric pressure, high strength cement shattered and cracked when perforated. Thus, the optimum cement strength was based on the appearance of neat and gel cement after perforating. In 1953, Clark showed a relation between cement strength and fluid shutoff.' He concluded that a 500 psi compressive strength is required for good fluid shutoff and that maximum bonding ability is developed at approximately 1,000 psi compressive strength. In 1964, Bell and Shore invalidated most of the conclu sions by the previous authors when they demonstrated that atmospheric pressure tests cannot be used to determine casing deformation and damage that will result from perforating under down-hole conditions.' They showed that the higher the hydrostatic pressure, the more restricted will be the expansion of gases generated by the charge. Less casing deformation and damage occurs under down-hole conditions than at atmospheric pressure. In recent work, Bearden et al. reported that jet perforating at surface pressure with the hollow carrier gun caused the cement sheath to shatter and crack.' The perforating, however, did not seriously affect the pressure required to leak past the casing cement bond. Only three cementing mixtures were tested, and presumably they had strengths in excess of 2.000 psi. Bearden et al. also reported that the hydraulic bonding strength increased as the compressive strength increased. Their hydraulic test showed that approximately 1,000 psi pressure is sufficient to break the casing cement bond for a well aged neat Portland cement sheath. Unfortunately, the tests were not run with a confining pressure, so Bearden et al. were merely measuring the strength of their outer 8%-in. casing. In our investigation, we measured the hydraulic bond strength of cement to pipe under a confining pressure and found that the bond strength was not limited to 1,000 psi. Cement Bond The bond strength is a good criterion for measuring the effectiveness of cement in performing its main function, that of preventing interzonal communication of fluids behind the casing. Measuring bond strength after perforating should be a good quantitative method of determining optimum cement properties, and should be a better method than that used by previous investigators,11 ' who simply observed the appearance of the cement after perforating.

Jan 1, 1969

By T. K. Perkins, L. R. Kern

A study of fluid mechanics, rupture of brittle materials and the theory of elastic deformation of rocks shows that, for a given formation, crack width is essentially controlled by fluid pressure drop in the fracture. Operating conditions which cause high pressure drop along the crack (such as high injection rate and viscous fluids) will result in relatively wide cracks. Conversely, operating conditions which cause low pressure drop (low injection rates and thin fluids) will result in relatively narrow cracks. Charts and equations have been derived which permit the estimation of fracture widths for a variety of flow conditions and for both horizontal and vertical fractures. INTRODUCTION There has been considerable speculation concerning the geometry of hydraulically created fractures in the earth's crust. One of the questions of practical importance is the width of fractures under dynamic conditions, i.e., while the fracture is being created and extended. Such width information could be used, for instance, to help estimate the area of a fracture generated under various conditions. Also, there has been a recent trend toward the use of large propping partiles.13, 15 Therefore is is desirable to know what factors can be varied in order to assure entry of the large particles into the fracture. There has been some work on fracture widths reported in the literature. In particular, there have been several Russian publications dealing with this sub-jeCt.1.31,3 These papers have dealt principally with the elastic theory and the application of this theory to hydraulic fractures. These studies have not led to an engineering method for estimating fracture widths under dynamic conditions. A recent paper3 has reviewed and summarized the Russian concepts. An earlier paper- from our laboratories also discussed the application of the elastic theory to hydraulic fractures. This first approach, based largely on photoelastic studies, has proved to be too simplified to accurately describe the fracturing process. However, these early thoughts have served as a guide during the development of more exact concepts. We would like to present in this paper our current concepts regarding fracture widths and some estimates of hydraulic fracture widths for several conditions. We believe that it is now possible to predict with fair accuracy the factors influencing fracture widths. Furthermore, the method of prediction has been reduced to a simple and convenient graphical or numerical calculation. CRACKS IN A BRITTLE, ELASTIC MATERIAL Many investigators2, 4, 30 have shown that competent rocks behave elastically over some range of stresses. Of course, if the tensile stress imposed upon a rock exceeds some limiting value, then the rock will fail in tension. In similar manner, there are some limiting shear stresses that can be imposed upon rocks. Hubbert and Willis11 have discussed the shear conditions which will lead to failure. Under moderate stress conditions (such as those likely to be encountered when hydraulically fracturing) and when stresses are rapidly applied, relatively, most rocks will fail in a brittle manner. Hence, for this discussion of hydraulic fractures in the earth's crust, we assume the rocks behave as brittle, elastic materials. Let us develop the discussion in the following way. (The following thoughts are applicable only to brittle materials.) 1. First we consider a brittle, elastic system. An energy balance will show the minimum pressure necessary to fracture rock, and from this pressure we calculate the minimum crack width resulting from extension of a hydraulic fracture. 2. Then we will show that, under ordinary fracturing conditions, fracture widths are appreciably greater than the minimum widths of extending fractures. In fact, we will find that crack width is controlled by fluid pressure drop in the fracture. 3. We will discuss pressure drops in fractures and resulting crack widths for various operating conditions and both vertical and horizontal fractures. 4. Finally, we will discuss the significance of these concepts, their relationship to fracturing pressures, etc. First, consider minimum fracture extension pressures. We can shed some light on this question by considering the theory proposed by Griffith7, 8 Yo explain the rupture of brittle, elastic materials. Griffith recognized that solid materials exhibit a surface energy8 (similar to surface tension in a liquid). The fundamental concept of the Griffith theory is that, when cracks spread without the application of external work (in the interior of an elastic medium which is stressed

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By M. M. Mebta, G. W. Dean, W. H. Somerton

With the advent of underground heating operations, interest has developed in the alteration of rock properties by high-temperature treatment. In the present work a number of sandstones were heated to temperatures in the range of 400°C to 800°C under both atmospheric and simulated reservoir pressures. Pertneabilities increased by at least 50 per cent and sonic velocities and breaking strerlgths decreased by an equivalent amount. Differential thermal expansion and other reactions of constituent min-era1 grains are the causes of these alterations. INTRODUCTION In the underground combustion of petroleum reservoirs, temperatures of the order of 600C are reported to have been reached in the combustion zone.' At this temperature rocks are subject to extensive thermal alteration. Temperatures of this magnitude and higher may also occur in subsurface formations when subjected to bottom-hole heating, thermal drilling operations, and underground nuclear explosions. Temperatures of this magnitude might also be generated by conventional rock drilling methods at points of bit-tooth contact. In earlier work, the permanent deformation of rocks resulting from heating was reported. Major structural damage of rocks occurs due to differential thermal expansion of mineral constituents. A number of mineral alterations including crystal inversions, loss of water of crystallization and dissociation, may also contribute to changes in physical structure and properties of rock. In the present work, samples of three typical sandstones were heated to several temperatures up to a maximum of 800C and then allowed to cool to room temperature. Heating was done under both atmospheric pressure and simulated reservoir pressure conditions. Physical properties of the samples were measured before and after heating and comparisons made. Measured properties included permeability, sonic velocity, breaking strength and fracture index. Changes in physical properties were compared to changes in mineralogical characteristics as determined by thin-section. X-ray diffraction and chemical tests. EQUIPMENT AND PROCEDURE Two outcrop sandstones (Bandera and Berea) and one sub-surface sandstone (St. Peter) were selected for the tests. These samples have a wide ranee in composition and physical properties as shown in Table 1. The first series of tests was made on 2-in. diameter by 5-in. long test specimens. Test specimens used in all later work were 3/4-in. diameter by 1 1/8-in. long, this being the specimen size required for heating at simulated reservoir pressures. After careful washing, the cores were oven dried at 100 ± 5C for a minimum of 24 hours before the tests were run. Test specimens were heated in an electric furnace at a constant rate of temperature increase of 3C per minute. When maximum temperature of the run was reached, the sample was allowed to soak for one hour. The furnace was then cooled to room temperature at the same rate of 3C per minute. The entire heating operation was designed for reproducibility without subjecting the test specimens to excessive thermal shock. For samples heated under simulated reservoir pressures, a pressure cell designed by Dean was used (Fig. 1).3 The core sample was inserted into a thin-walled (0.006 to 0.01-in.) copper cup which was then mounted in a high-pressure cell. Provisions were made for the application of internal pore pressure as well as confining pressure. Tests showed that the thin-walled copper cup closed tightly around the core and satisfactorily transmitted confining pressure to the core. The core was heated by placing the entire cell into the electric furnace. The heating program was the same as that used in the atmospheric pressure runs: tempera-ture rise of 3C per minute to maximum temperature of the test, soaking at maximum temperature for one hour, and cooling at a rate of approximately 3C per minute. The cell was designed to withstand 5,000 psi at 1,000C. However, since it was considered likely that repeated heating and cooling would in time weaken the steel, 2,000 psi at 850C was set as a working limit. In the present series of tests, the pore pressure was held constant at 750 psi and the confining pressure at 1.500 psi. The pressure source was a high-pressure nitrogen tank. The two pressures were controlled manually but are accurate well within ± 50 psi.

Jan 1, 1966

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.&apos;- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers&apos; have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.&apos; The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.&apos; The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954