Search Documents

By R. D. Pehlke, J. V. Gluck

The effect of small additions of silver on the actiziity of zinc in dilute solution with molten bismuth has been determined ill the range 450° to 650°C. Experimental measurements were made in a multi-electrode galvanic cell. All zinc activities showed large positive deviations from Raoult's Law. The results are expressed in terms of the interaction parameter EJ, as defined by Wagner. In the binary Zn-Bi system, Henry's Law was followed at zinc concentrations below 5 mol pct, thus indicating that the binary or self-interaction parameter of zinc in bismuth is essentially zero. The Henry's Law con- THE determination of thermodynamic interaction parameters requires accurate knowledge of solute activities in the dilute-solution region. Dealy and Pehlke1 have summarized the basis for interaction relations, discussed some theoretical implications, and presented a compilation of interaction parameters calculated for molten nonferrous alloys from stant ranged from 2.43 at 650°C to 3.96 at 450°C. The binary zinc activities were consistent with published data for higher zinc concentrations . The ternary interaction parameter ranged from -1.90 at 650°C to -3.30 at 450° C, varying linearly with the reciprocal of the absolute temperature. The negative value for the parameter reflects the fact that addition of silver decreases the activity of zinc in solution with bismuth. data available in the literature. Most of the data were for two-component systems from which only the self-interactions, Ei, could be calculated. Concentration ranges were often such that a considerable extrapolation was required for calculations at lnfinite dilution. The data for ternary systems were quite limited and often unavailable in suitable systematic fashion—thus few values of the parameter e| could be obtained. Knowledge of both the binary and ternary interaction parameters is necessary for the estimation of the activity coefficient of a given dilute solute in

Jan 1, 1965

By William I. Gardner

Optimum design of a structure obviously requires a thorough knowledge of the materials to be utilized in its construction. When the structure is a tunnel, a most important element in its design and construction is the geology. As a tunnel may be many miles in length and at depths of hundreds or thousands of feet, we face a real problem to meet the needs of the designer and builder. How can we determine the properties of our construction materials in this situation? Engineering geology has had a formidable challenge to meet the requirements of conventional excavation methods; the advent of machine methods for rapid excavation compounds the requirements for more detailed and more precise geological knowledge of the tunnel site. This chapter will discuss the means now at our disposal to meet the challenge to produce the required data on the tunnel site in the preconstruction stage. Our considerations will be directed towards construction of a free-flow tunnel, primarily in fractured rock formations, without any requirements for the rock mechanics type of in-situ tests that might be made for a pressure tunnel or for a large opening for an underground power plant. In essence the investigation must determine: (1) The geologic conditions affecting the type of construction equipment and excavation method of the rock to be broken and removed. (2) The quantities of water and gas to be encountered. (3) The strength and stability of the material surrounding the bore and its need for support and lining. GEOLOGICAL FACTORS AFFECTING TUNNEL DESIGN AND CONSTRUCTION The engineer or contractor may classify the rock as either competent or incompetent or more pointedly as "good" or "bad" ground. The geologist may bestow a precise petrographic name upon the rock, such as granodiorite or indurated tuff breccia or name the formation, as Mancos shale, for

Jan 1, 1970

By W. Julian Patron

TREATMENT of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro- separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low- grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. OPERATION AND TYPES OF SETTLING EQUIPMENT Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1946

By W. Julian Parton

Treatment of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro-separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low-grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. Operation and Types oF Settling Equipment When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1947

By W. Julian Parton

Treatment of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro-separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low-grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. Operation and Types oF Settling Equipment When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1947

By Rex W. Woods, Morris Muskat

A leastmsquare analysis procedure has been developed and applied for the study of the deviations in estimations of oil in place as given by the material-balance equations. The data used were those obtained from field observations on the Jones sand in the Schuler pool, Arkansas, and the Monroe dolomite in the Reed City pool, Michigan. Possible effects of water intrusion were taken into account by expressing the cumulative water influx in terms of various functions previously proposed in the literature. Formulas were developed and values calculated for the minimum deviations and minimal percentage deviations in the calculated volumes of oil in place from the average values, as could be obtained by suitable choice of the water encroachment and initial gas-cap volume parameters. The results show that the fluctuations in these calculated volumes are very insensitive to the values chosen for the rate of water intrusion and initial gas-cap volume, and hence cannot be safely used in discriminating between spurious values for these parameters and such as actually pertain to the producing reservoirs. Moreover, the exact form of the water-intrusion function seems to have but little effect on the fluctuations in the computed oil in place. Accordingly, it is concluded that the material-balance method does not of itself provide a satisfactory criterion for determining the basic physical unknowns of producing reservoirs or in making conclusive decisions regarding the production mechanism, unless independently established geological control data are available for eliminating unreasonable values for the reservoir parameters, even though they may still satisfy the material-balance formulas. If, however, from core or logging data the initial oil in place and the gas-cap volume can be established in advance, the material-balance formulas can be inverted to find the water intrusion. Moreover, by determining by such calculations the water-intrusion coefficient, the iuture production performance can then be predicted by the aid of the materiaI-balance formulas for specified operating conditions. This type of application may be of particular value in predicting the results of Pressure-maintenance operations. Introduction The evaluation of the forces acting upon an oil reservoir is a problem of considerable interest to the operator as an aid in determining the proper method of operation for the reservoir to obtain an optimum recovery of oil. In many pools, the nature and magnitude of the forces acting upon the reservoir remain unknown until an appreciable amount of ultimate recovery is obtained. To be of value to the operator, a reliable interpretation of reservoir performance should be available in the early life of the pool to permit an optimum plan of operation. Progress has been made in an understanding of reservoir behavior and the importance of the different factors involved. The material-balance method of estimating oil in place has been proposed as a tool in analyzing reservoir-performance problems.l The solution of such problems by this method ordinarily involves two or more unknown values relating to the nature of the reservoir, and the results

Jan 1, 1945

By R. A. Oriani

The partial molal volume of hydrogen is one of the parameters that describe the elastic interaction between the solute and the stress fields about inclusions, dislocations, and cracks. As such the partial molal volume is probably of importance in the elucidation of phenomena such as hydrogen embrittlement and hydrogen yield point. A knowledge of this quantity would also be helpful in thinking about the state of dissolved hydrogen in iron. However, because of the very low lattice solubility of hydrogen in iron the usual ways of determining the lattice expansion are not practicable. It is therefore of interest to apply the thermodynamics of stressed bodies to two sets of measurements of the effect of elastic stress upon the permeability of hydrogen in order to deduce a value of the partial molal volume, VH, of hydrogen dissolved in a iron. Beck ..' and previously de Kazinczy, observed that a uniaxial tensile stress increases the permeability of hydrogen in iron and in various steels. Beck et 01. employed Armco iron and A.I.S.I. 4340 steel, whereas de Kazinczy used a steel the composition of which was 0.13 C, 0.23 Si, 0.46 Mn, 0.006 P, and 0.038 S. Upon releasing the stress the permeability increment disappeared if the stress was below the elastic limit. Both investigators employed cathodic charging to introduce the hydrogen. de Kazinczy measured the permeation through a thin-walled tube by collecting the gas, whereas Beck et al. measured the permeation through sheets of various thicknesses by a very sensitive electrochemical technique. Both investigators measured the steady-state permeation at constant rate of hydrogen ion discharge, and Beck measured in addition the hydrogen diffusivity by a time-lag technique which is independent of the boundary conditions. Beck et al. and de Kazinczy found a linear relationship between log (J,/Jo) and the stress, where Ju/Jo is the ratio of the flux of hydrogen when the metal is under uniaxial tensile stress, a, to the flux under zero stress, for the same temperature and charging current. Beck et al. found in addition that the diffusivity of hydrogen is not changed by stress. Both investigators concluded that the observed change in permeability is due to an increase in hydrogen concentration, and furthermore that the increase in concentration is due directly to the thermodynamic effect of stress upon concentration. Accepting this assessment of the situation for reasons given below, one may use the equation3j4 in order to evaluate I/H, the partial molal volume of hydrogen. This equation is valid for the domain of a/E «¦ 1 (where E is the Young's modulus) and under the assumption that hydrogen expands the lattice isotrop-ically. From the data of Beck el al, one calculates V7H - 2.0 cu cm per g-atom, and from those of de Kazinczy one obtains 1.8 cu cm per g-atom. That the increase of concentration with stress is indeed of thermodynamic origin is attested to by the facts that the experimental results conform to the thermodynamic relation, Eq. [I], and that the results are the same whether a pure iron1 or each of two different steels172 is used. Neither of these facts wou1.d necessarily be expected if the effect of stress were, rather, to increase the ratio kn/k, of the kinetic factors of the following competing reactions: H(ads) — H (dissolved) Such a change of kinetics at the surface could be an alternative explanation of the effect of stress on the permeability. Although this writer does not deem this explanation to be the correct one for the reasons given above, it must be admitted that unambiguous proof that the phenomenon has a thermodynamic origin does not yet exist. Two kinds of experiments may be suggested. One is to plate a variety of metals on the input surface of the steel and repeat the stress experiment at a variety of hydrogen charging currents. The other is to employ somewhat thicker specimens in order to be able to apply uniaxial compressive stress. Eq. [I] shows that ln(c,/c,) depends on the sign of the stress, but it is difficult to see a physical basis for which k2/kl would depend on the sign of a. The present value of V^ in a iron agrees with phragmen's5 estimate, which he based on comparisons with the lattice expansion by hydrogen of titanium, zir-

Jan 1, 1967

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By D. L. Feucht, R. L. Longini

The semiconductor heterojunction is considered in terms of simple models which may lead to an understanding of move complex heterojunctions. Metallurgical and electrical properties of hetero-junctions aye discussed including the interface structure, energy -band diagram, and carrier transbovt across the interface. It is found that in a heterojunction all mechanisms such as injection, tunneling, and junction recombination found in simple junctions play modified voles. INTERFACES between materials (grain boundaries, the electrical junction between two differently doped materials in a single crystal, the oxide-metal interface, or metal-metal junctions) are of considerable importance in many situations. These various interfaces all have one very fundamental thing in common. Quantum mechanically speaking, the wave functions of the electrons in one material may penetrate the other material but, in general, only to the extent of angstroms. From an electrical point of view the conduction mechanism changes as a current passes through such junctions. In some cases the change is tremendous, in others almost negligible. The interface, then, is the locus of a change of conduction mechanisms. Some of these, particularly in semiconductors, are well-understood. The ordinary p-n junction in a single crystal can be the locus of an injection mechanism or a tunneling process, depending on conditions. The mechanisms are probably best understood in semiconductors because of the possible simplified view of particlelike conduction. The bands are either nearly filled or nearly empty and band overlap is seldom involved. The same fundamentals are probably important in other situations too but they are very difficult to look at naively. Although the simple look at the semiconductor case only gives us a relatively rough picture which must then be refined, the other systems, which involve a more complex situation, immediately are in many ways too difficult. There are too many initial choices of complex systems and therefore it is not possible to be even reasonably certain of any one model. Because of the relative simplicity of semiconductors, their good and controllable structure, and because of the ability to make many measurements on them not normally available to either metals or insulators! they are probably the best understood materials. It is therefore desirable to use them as a tool to further the understanding of interfaces in general. Semiconductor-heterojunction concepts were first proposed by kroemer1 in 1957. This was followed several years later by reports on the fabrication and experimental characteristics of heterojunction structures by Anderson2 and Diedrich and jotten.3 I) THE HETEROJUNCTION STRUCTURE To get down to hardware, when we refer to a semiconductor heterojunction we imply that there exists an intimate contact between different semiconductor materials. We could put two pieces of material together, complete with oxide layers, we could remove the oxides, or we could even melt the interface and hopefully get wetting and a good "bond" on solidifying. In fact we could by some means grow a crystal of one material using the other as a seed. Essentially we are interested only in the last two because they are the simplest to look at analytically. The degree of perfection of fit varies greatly and is reflected somewhat in the arc welder's joint strength. The lattice match of the two materials, their orientation, and so forth. is obviously necessary for a good bond but so is the continuity of any polar bonds which are involved such as in the III-V semiconductors. The mechanical misfit between two similar lattices can be described in terms of edge dislocations. The edge-type dislocations must be very close together for the usual misfit and there must be dislocations for each of several different Burger's vectors in order to produce a lattice match. The .'dangling bonds'' resulting will be involved in producing interface charge. Order of magnitude estimates of the charge density extrapolated from low densities of dislocations in homogeneous materials give 5 x 1013 cm-2 Ge-Si and 1 X 1012 cm-2 Ge-GaAs electronic charges. Edge dislocations also act as very active recombination centers between holes and electrons. One lattice "matching" difficulty usually exists even if two structures have essentially the same lattice constants as they will have different coefficients of therma1 expansion. Thus, on cooling from the usually high temperature of fabrication to room temperature, dislocations are produced, a good fit not existing at both temperatures. In brittle materials this shrinkage may even result in cracking. For the Ge-Si interface the mismatch is about 2 x 10 -6 per degree whereas it is less than 10"7 per degree between germanium and GaAs. The exact effect of the misfit is dependent on the thickness of the materials involved. For a very

Jan 1, 1965

IN the western mines, the boss, engineer, geologist, or nipper in making rounds have a password which usually guarantees safe entrance to a working place from below the working miner. Most men won't climb a raise or enter a stope from below where a miner is working until they have shouted "nothin' down" and heard those words shouted back by the miners above. "Nothin' down" is a safety pledge as necessary and as binding as the truce flag to the soldier. It implies mutual confidence that work will be suspended until the person below has come abreast of the workers; and also confidence that the miner who replies "nothin' down" is reasonably sure the place is safe to enter. Like truce flags which are not infallible, so is this password subject to human errors or unexpected falls of rock, tools, or timber. Everyone knows these unavoidable hazards, but what is important to the exposed man is that in that precise moment of time when he has heard the reassurance of "nothin' down," he knows that safety is uppermost in the minds of the men above him. With such assurance we would go anywhere and so would most mining men. If that period of safety consciousness, procured by the utterance of two words, could be multiplied to equal the hours in the working day, there would not be any accidents but those by "the act of God." It is the aim of every safety program to make safety as natural as breathing. That is the reason for the posters, the conferences, instruction periods, safety engineers, and the inspections. But none of these are as effective as one accident, which keeps men on their toes for weeks to come. This is not the price we want to pay for safety consciousness. This Annual Review number of Mining Engineering is full of talk about production. Production for defense, production for profit. In this tremendous surge of industrial might . to make this nation and our very families safe S from the predatory forces abroad in the world today; let us not lose sight of the fact that the . safety of our manpower is more precious than any commodity. Production without safety is detrimental to the national interest, to that of the company, and to the individual. If the words "nothin' down" can give us the best human guarantee of safety, for however brief a time, let us adopt them at least in principle as our slogan in 1952. Production for preservation in '52 - but NOTHIN' DOWN!

Jan 1, 1952

The Rio Tinto - Cerro Colorado operation was the first major cyanide plant built out of South Africa since the Carlin and Corte mills came on-stream in 1965 and 1969. Its flowsheet was presented in the original monograph, "Gold and Silver Cyanidation Plant Practice, " published in 1975, with a brief description of the plant but without the operating costs. The authors have recently received these data and it was believed worthwhile to present them in this volume along with the aforementioned flowsheet. The Cerro Colorado ore deposit is located at Minas de Rio Tinto in the province of Huelva, Spain, approximately 88 km (55 miles) north- west of Seville. The previously mined copper ore bodies lie on either side of the deposit which is mainly copper ore. The crest of the deposit is a capping of "gossan" containing hematite, limonite, gold, and silver. Separate facilities for primary crushing, concentration of copper ores and cyanidation of gold-silver ores are provided. Fine crushing is common to both ores. The run-of-mine open-pit ore is fed from a stockpile via a surge bin and apron feeder to a jaw crusher. After crushing to minus 150 mm (6 in. ), the ore is washed in a rotary scrubber to remove the clay material ahead of fine crushing. Minus 6 mm (1/4 in. ) screen undersize is pumped directly to the grinding circuit with the screen oversize being crushed to minus 19 mm (3/4 in. ) for feed to the primary ball mill; this is followed by two subsequent stages of ball mill grinding to 80% minus 43 microns (325 mesh). Grinding is with water only; no cyanide is used. After thickening, lime is added to the first two of seven Pachuca tanks for conditioning ahead of cyanide addition in each of the five remaining Pachuca tanks. This flowsheet indicates rapid cyanide consumption and the need to maintain a high strength cyanide solution for silver extraction. Agitation for dissolution of the gold and silver is followed by standard CCD practice employing four 67 m (220 ft) washing thickeners in series, with repulping between each thickener. A departure from American and Canadian practice is the use of Stellar filters developed in South Africa for pregnant solution clarification and recovery of zinc-gold-silver precipitates. The precipitate is treated with acid for zinc removal, the sludge filtered in presses, dried, calcined and smelted to produce dore bullion of 900 fineness containing 12% gold and 78% silver.

Jan 1, 1981

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.' The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago' for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles'" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

By Henry Leidheiser, Melvin C. Jr. Hobson

The rate of formation of the intermetallic compound, indium antimonide, at the interface between iudium and antimony at 100°C is greatly increased when a composite electrode of indium electrode -posited on antimony is made the cathode in an electrolytic cell. The amount of indium antimonide formed during electrolytic treatment at constant potential appeared to he proportional to the square root of time, but the scatter of the data, particularly at long times, makes it impossible to state this conclzlsi1:ely. The rate constant for the electrochemical synthesis was estimated to he 1.5 x 10-12 sq cm per sec. A similar- set of experiments was conducted in the absence of an applied potential but under otherwise similar conditions. The rate constant lor the thermal synthesis was less than 2 x 10-14 sq cm per, sec, at least two orders of magnitude less than obtained during electrolytic treatment. In a series of electrochemical studies it was observed that intermetallic compounds formed on the surface of polarized electrodes.1'2 The possibility of using this technique for the electrochemical preparation of intermetallic compounds was investigated and subsequently applied to the synthesis of the semiconducting III-V compounds. Gallium antimonide, indium arsenide. indium antimonide, and indium bismuthide were successfully formed by electrodepositing the Group III element from a boiling acid solution onto an electrode made of the Group V element. The following kinetic studies were undertaken on indium antimonide to obtain quantitative information on the rate of formation of this representative III-V compound under a potential gradient. EXPERIMENTAL The electrolytic cell for these experiments was a modified, three-neck, round-bottom, 500-ml distillation flask. Sealed into the side of the flask was a Luggin probe which monitored the surface of the working electrode and extended out of the flask to a small reservoir containing a saturated calomel electrode. The counter electrode was platinum. The three electrodes were connected to a Wenking po-tentiostat which maintained a preselected constant potential near the surface of the working electrode with reference to a saturated calomel electrode. All potentials noted in this paper are with reference to a saturated calomel electrode at 45° ± 5°C. The potential and the current were both monitored using Sargent Model MR recorders. The antimony electrodes were cast in graphite molds to form spheres about 15 mm in diameter with a shank 6 mm in diameter and 10 mm long. A heavy copper wire (12B & S gage) was soldered to this shank. Collodion was applied for protection to the shank and the connecting part of the copper lead. A snug-fitting O-ring was slipped over the shank and the electrode was then fitted into a teflon holder such that only the spherical portion was exposed. The electrode surfaces were cleaned and chemically polished prior to assembly and introduction into the electrolyte by etching in a modified CP-4 solution (50 parts glacial acetic acid, 10 parts concentrated nitric acid, 2 parts 48 pct hydrofluoric acid). The electrolyte was 10-2 M In+3 in 1 MH2So4 and its temperature was held constant by refluxing. The reflux condenser was open to the atmosphere and no temperature correction was made for changes in barometric pressure. The indium concentration in the electrolyte was checked from time to time by the analytical method outlined below for the determination of the amount of indium antimonide formed electrochemically. A schematic of the recorded potential is shown in Fig. 1. At point A the antimony electrode was introduced into the cell and the open-circuit potential recorded. At point B the potentiostat, preset at the desired potential, was switched on. It was switched off at point C and the potential fell to the open-circuit value of the electrodeposited indium. The

Jan 1, 1965

By V. M. Dobrynin

Experimental data demonstrate that physical properties of porous rocks change under pressure. In this paper an assumption is made and proved that under pressure the changes of physical properties such as porosity, density, permeability, resistivity and velocity of elastic waves are controlled to a large extent by the pore compressibility of rocks. It is also shown that the pore compressibility of rocks can be determined, within the range of pressures from 0 to 20,000 psi, by knowing the maximum pore compressibility and the magnitude of the pressure. Mathematical equations were developed which permit one to define changes in physical properties of porous rocks under pressure. These equations were verified by experimental data obtained from the study of sandstones. INTRODUCTION In studying the behavior of porous rocks under pressure in the field of petroleum technology, the most interesting aspect is the observation of those properties which characterize the rocks as possible reservoirs — for example, porosity, permeability, resistivity, density and the velocity of elastic waves. The literature dealing with this problem mainly contains data concerning the study of only one or at most two of these parameters, but not of the group as a whole. An attempt is made in this paper to find general equations involving each of these parameters, which will permit the study of the behavior of rocks under pressure. All experimental data used here were obtained from the investigation of consolidated sandstones. EXPERIMENTAL In addition to the use of published experimental data, an experiment was carried out which studied the main physical properties of sandstones under pressure. Two homogeneous quartz sandstones were chosen for this purpose: (1) the Torpedo sandstone from Kansas, and (2) the Medina sandstone from Ohio. The porosity of the Torpedo sandstone was 20.2 per cent, and that of the Medina 8.7 per cent. Permeabilities were 45 md and less than 1 md, respectively. Each sandstone contained about 5 per cent clay minerals, consisting mostly of kaolinite and chlorite, which were distributed quite evenly throughout the samples. One cylindrical sample 2 in. in diameter and 5 in. in length was cut from each sandstone and then saturated in a vacuum with a 3N solution of NaC1. This high concentration was used in order to obtain true formation factors and to decrease the swelling of the clay minerals. The methods of mounting the samples and measuring the changes in porosity and resistivity were practically the same as those described by Fatt and Mann.1,2 Changes of resistivity under pressure were studied for sandstones with 100 per cent water saturation, and for sandstones with the irreducible water saturation. The irreducible saturation was obtained by enclosing the saturated rock samples in relatively fine silicate powder so as to remove the water by capillary action. This procedure is described by Orkin and Kuchinski.3 Changes of permeability with pressure were determined at room temperature using nitrogen as the flowing medium. In studying the effects of pressure, one series of measurements was made using an internal pore pressure Pi equal to the atmospheric pressure, while the overburden pressure Pe ranged from 0 to 20,000 psi. A second series of measurements was used over the same range of overburden pressure, but with an internal pore pressure of 1,800 psi. When the results were compared on the basis of net overburden pressure (Pe — 0.85 Pi ), there was practically no difference for these two sandstones. The origin of the factor 0.85 in the expression for net overburden pressure is given by Brandt,4 Fatt5 and Geertsma.6 The relatively large bulk volumes of the sample (about 15 cu in.) made it possible to observe a

By L. N. Cosner, C. F. Austin, J. K. Pringle

Shock wave attenuation studies with three igneous rocks are reported: a spessartite elastic to low intensity stress waves, a diorite which is anelastic, and a porous scoria. The level of shock passing through a given thickness of rock has been determined by donor-receptor methods using high speed streak cameras. Test results include shock propagation velocities adjacent to the explosive, the dependence of test results upon test geometry, and the variation in shock wave attenuation in these three common igneous rock fabrics. The utilization of explosives in rock mediums involves a series of interrelated phenomena. These are the detonation process within the explosive, the transfer of energy from the explosion products to the surrounding rock medium in the form of sound or shock waves, and the transmission of the resulting waves through the rock medium to create damage in the rock mass. The subject of this paper is the investigation of the close-in phenomena that occur in the intensely shocked rock immediately adjacent to a detonating explosive charge. The specific aspects studied include propagation velocities, free surface velocities, pulse attenuations and the determination of the equations of state for the test rocks employed. In addition, a series of tests was conducted to indicate the dependence of the test results on the charge diameter utilized. The equations of state for rock materials have been investigated by a number of authors. Lombard, ',' Grine and Fowles,3,4 Zharkov, 5 Hughes and McQueen,6 Chabai,7,8 and Bass9 have published equation of state data on rock materials similar in structure or composition to those investigated in the study. Rinehart10 has prepared a voluminous tabulation of the available equation of state data from these publications and in addition has included data on many other rock and earth materials in his compilation. The reader is referred to the extensive tabulations and bibliography of Rinehart for classical studies involving the equations of state of metals and other solids and liquids. The problems of sympathetic detonation between drill holes in hard rock environments has received the attention of various authors as have the problems of explosive rock coupling close-in stress wave attenuation and explosive diameter effects. 11 to 18 In particular, the don or-receptor geometry of this report is very similar to the geometry of adjacent drill holes in rock. Most published pulse velocity and attenuation work in rock has been devoted to velocities at much lower amplitudes than those associated with close-in explosives phenomena and most attenuation studies involve transmission and attenuation across large spans of material. Excellent work in these areas has been published by the U. S. Bureau of Mines and by many individuals and groups engaged in geophysical research. SELECTION OF TEST MATERIALS A series of rock materials was desired for this test program that would be meaningful industrially, and that would also yield comparative results from a research viewpoint. Based on the availability of a series of related petro-fabrics, for which there is an abundance of physical and shock response data, three igneous rocks were selected as the test series. The applicability of shock wave studies in igneous rocks to industrial problems is readily demonstrated. Hardrock tunneling, quarrying and mining take place in igneous rocks throughout the world. From a research point of view, igneous rocks exhibit a wide variety of grain sizes and considerable diversity in composition, yet the common igneous rocks have a general similarity in their constituent mineral structures and in their grain-to-grain bonding mechanisms. The latter is based on the concept of rock formation through magma cooling and crystallization, though the degree of liquefaction in granitic plutonic masses is indeed a moot question. Three specific types of igneous rock were chosen for study. A coarse-grained granitic textured rock was desired that would serve as a representative of the widely abundant intrusive rocks of the world and

Jan 1, 1967

By Herbert W. Huse

Nitrogen, and its compounds, unique among the materials described in this volume, is absolutely essential to the existence of the human race. Almost all minerals are important and the absence of any one of them would be sorely felt; but nitrogen is an integral part of the cycle of life itself. Man cannot live without nitrogen which, as an inert gas, composes the major part of the air he breathes; as compounds, nourishes the vegetation which he eats; and, as protein, forms a part of his very flesh and blood. Nature originally provided man with a vast reserve of usable nitrogen compounds in the form of fertile soil. She constantly replenishes the supply by "fixing" nitrogen in the air at the estimated rate of 400,000,000 tons per year (an insignificant 6 lb per acre) during electrical storms. She has also placed certain microorganisms in the soil which are able to "fix" nitrogen and convert it into forms which plants can use. Legumes like cow peas, soy beans, clover, and alfalfa have extraordinary roots which serve as stimulating hosts to these bacteria which, in turn, nourish the plant. By plowing in all or part of such crops, their above-average nitrogen content can be returned to the soil for other more useful crops. The mechanism for this recycle is supplied by "denitrifying" bacteria which attack the dead plant tissue and liberate nitrogen and ammonia. However, since one crop of grain, sugar beets, potatoes, tomatoes, etc., takes out a major portion of the nitrogen which a plowed-in legume crop can supply, this method of fertilization is obviously inadequate. Drastic intervention by man has become necessary to support the ever-growing population of the world.9,15,20 Old civilizations with a high population density, such as the Chinese, were able to exist for centuries by carefully tilling the soil, rotating crops, and returning to the soil all the nitrogen in vegetable wastes plus human and animal excreta. But the lack of a means for augmenting their supply of nitrogen placed a ceiling on further development and kept the mass of the population in a chronic state of undernourishment, frequently punctuated by famine. Nitrogen plays another important role in the life of mankind. In the form of explosives, nitrogen helps to wrest from the earth many materials needed for our material well-being. Also, in the form of explosives and propellants, nitrogen increased the destructiveness of wars to a point only exceeded by the fantastic power of atomic energy. Man's first really effective efforts to improve his position with respect to nitrogen began in the 18th Century with the mining of sodium nitrate. By the late 1880's this had become a big industry serving a large part of the world. In the late 1890's nitrogen, in the form of ammonia, was being recovered from coke-oven operations. In 1900 nitrogen, in the form of nitric oxide, was being obtained from the air by an electric-arc process. About 1904 another "fixation" process based on the reaction of nitrogen with calcium carbide to form cyanamide was commercialized. By 1913 the Haber-Bosch process of "fixing" atmospheric nitrogen by reacting it with hydrogen to produce synthetic ammonia was successfully applied on a large scale, first in Germany and then throughout the industrial areas of the world.9 All the above methods of obtaining nitrogen compounds are still in use and, between them, they assure mankind of adequate supplies for all time. While this fortunate situation is not unique amongst industrial raw materials, all too few of man's needs are so well in hand.

Jan 1, 1960

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962