Search Documents

By William R. Webster

At the Florida meeting of the Institute, in March, 1895, I presented a Note on a Proposed Scheme for the Study of the Physics of Cast-Iron,1 giving an outline which, for convenience of reference, I here repeat. Suggested Lines for DiScuSsion and IvestiGation. I.—Correspondence between chemical composition and melting-point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: 1. Cupola-mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting-temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6 Kind of mold, green sand (under dif- on E. Chill. ferent conditions of ramming, amount F. Residual strew of moisture, and skin-dried), dry sand, G. Condition and quan- loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum, III. —-Segregation as affected by : 1. Composition ; 2. Casting-temperature; 3. Rate of cooling ; 4. Size and shape of casting. IV. —Blow-holes, their volume and position as affected by: 1. Composition; 2. Casting-temperature; 3. Casting-pressure ; 4. Rate of cooling; 5. Size and ehape of casting ; 6. Special additions. It was hoped that a discussion might thus be elicited, similar in interest and value to the discussion of the physics of steel, which had been so widely and gratefully welcomed by students and practitioners in that department. That this hope was not

Jan 1, 1905

ARTHUR CROWFOOT, Morenci, Ariz. (communication to the Secretary*).-In order to set at rest any doubts in regard to the reasons for selecting the Callow pneumatic flotation process for use in the concentrators of the Arizona Copper Co., Ltd., at Clifton and Morenci, I am presenting the following facts gained from the results of test work carried out on the Callow and Cole-Bergman types of flotation machines at Morenci. Prior to the comparative test of merit between the Callow and Cole-Bergman machines, many months' time and a large amount of money had been expended in the development and testing of the Cole-Bergman machine, and it was necessary to decide quickly what make of machine was best to install. The Callow pneumatic flotation process was recommended for installation in our concentrators for the following reasons: The results indicated: 1. That the Callow system made the highest extraction of copper values from the feed treated. 2. That the Callow system was simpler to operate and could he operated it a lower cost. 3. That the Callow system operated with a lower air pressure. (The question of the actual power consumption of the two types of machines was not definitely settled at this time.) During the official test period the Callow flotation apparatus showed an additional recovery of from 1 to 1.5 lb. of copper per ton more than the Cole-Bergman machine, this difference being maintained by further treatment of the tailing from both machines. The simplicity of the operation of the Callow flotation system is one of its notable features, two operators per shift being able to handle 90 standard cells and blower equipment.

Jan 7, 1917

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied 1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature, 4,5 and time of exposure." The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The —65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min. The oxidation of coals and carbons was performed in a vertical, electrically heated glass tube, shown in Fig. 1. One hundred grams of —65 mesh coal were fed into the glass tube and heated to 10° to 20 °C below the predetermined temperature of oxidation. Compressed air was admitted to the tube at a rate of 0.05 cu ft per min and the temperature was controlled by a variable voltage regulator. The oxi-

Jan 1, 1955

No. 345.-Assayer. A man 35 years old, or over, experienced in general mineral assaying, particularly of tin and tungsten ores. To locate in Bolivia with a strongly established house. No. 346.-A firm of consulting and managing engineers, having charge of certain coal-mine properties in Illinois, requires the services of the following: (a) Mine transitman, who has had underground experience and is capable of making accurate surveys. Salary $150 per month to start. (b) Mining engineer, possessing strong personality, and experienced both in surface and underground work, who is capable of taking complete charge of several coal properties. Salary $175 per month. (c) Four rodmen for mine surveying. Salary $85 per month to start. Candidates for the above positions should be able to report to the company's Illinois office at once. No. 347.-A South African development company will shortly require the services of a mill superintendent, who has :a general knowledge .of concentration, particularly of flotation, and is able to take charge of a copper concentrator treating 15,000 tons per month and employing 200 natives and a small number of white men. Salary is £60 per month to start, and the company supplies an unfurnished room or house, including free light, free water and free sanitary service, together with one native house servant. I A contract will be made for six months, and notice of three months by either party will be required to terminate the engagement after six months. An allowance of £75 for travelling expenses will be paid on arrival in South Africa to a single man, or £125 to a man who brings his family. Salary begins upon arrival

Jan 10, 1918

By M. E. Shank, J. Wulff

In view of the current interest in magnetic materials having rectangular hysteresis loops, as for example those obtained with the grain oriented 50 nickel 50 iron alloys,t we wish to call attention again to the results obtainable with the perminvar (Co-Ni-Fe) alloys heat treated in a magnetic field. Data taken from direct current measurements made prior to and during World War II give the typical values shown below for two of the perrninvar alloys. Fig 1 and 2 show- the hysteresis loops for these samples. The first sample above consisted of small rings punched from 0.014 in. sheet stock. These rings were heat treated at 1000°C for one hour in a hydrogen atmosphere and then cooled with the furnace to 750°C at which point they were subjected to a magnetic field of 15 oersteds maintained during cooling to room telmperature. The molybdenum perminvar sample consisted of a spirally wound core of 0.001 in. tape. The heat treatment was the same except that box annealing methods were used and no hydrogen atmosphere was employed. Even better properties might be expected using hydrogen. The heat treating temperatures and cooling rates are not critical. Rectangular hysteresis loops produced in other perminvar alloys by heat treatment in a magnetic field were described earlier.',? Properties similar to those described above are realized in perminvars manufactured by conventional methods. Drastic cold working which in practice limits the final thickness and is gen- erally expensive may thus be avoided. This information may be of interest to those concerned with magnetic alloys and the development of contact rectifiers, magnetic amplifiers and so on.

Jan 1, 1950

By J. Spotts McDowell

J. W. RICHARDS, So. Bethlehem, Pa.-The paper is certainly an exceedingly, valuable one and it gives detailed information which should be utilized in the following way. There are probably twenty different circumstances or conditions under which silica bricks are used. Sometimes they are used under high pressure, at others under low pressure, at times for low temperatures and others for very high temperatures. If the methods of this paper are followed out, and if the precise mechanical and thermal properties are determined and can be reproduced, the industry can furnish the proper brick for any particular purpose. There is at present only an imperfect classification made as to properties and uses, but we need a "much more scientific classification of the uses to which the bricks are to be put and then should manufacture the bricks suited particularly for each of those purposes. There is one property which is not mentioned in the paper and which is of considerable importance, that is, the 'electrical conductivity. There may be other properties besides, which a good research laboratory can determine, and when we have listed all the various properties and noted the way in which they can be reproduced, the maker can then specify his exact requirements and the corresponding quality of brick can he selected or made to meet them. H. D. HIBBARD, Plainfield, N. J.-About a year ago I had some experience in another country, in melting steel, where silica bricks made in that country failed, but in a different way from those in America. Here, when the bricks get too hot, they are partly melted and string down

Jan 4, 1917

By K. G. Black, B. P. Faulkner

Laboratory batch flotation rests are used for comparison of the floatability of ores and for comparison of the effect of various treatments on ore floatability. Although it is difficult to predict exact recoveries for continuous flotation on the basis of batch tests, considerable quantitative information can be obtained through their use. A simple method is presented which provides a convenient means of quantitatively evaluating results from laboratory batch tests. The information obtained is in the form of a discrete flotation rate distribution, which, if desired, can be used directly in a simulation of continuous flotation. Equation of Batch Flotation The validity for batch flotation of the first-order kinetic equation is accepted: [ ] where k is flotation rate of a class of articles and W (t) is weight of particles of the class in cell at time t. Thus, at time t, the fraction of the original amount of the class of particles still remaining in the cell is [ ] where W (0) is weight of class of particles in cell at time zero. If there are several classes of particles in the cell, each with its own flotation rate, k4, the fraction of the particles remaining is [ ] where W (t) is now the total weight of n classes, a, being the original fraction of W (0) belonging to the ith class. Accordingly, [ ] [Fig. 1] shows the result of a typical batch test. Such result can be characterized by a set of particle classes, each set described by a flotation rate, [ki,] and a corresponding fractional magnitude, [ai.] [ ] Multiple Regression Equation Eqs. 3 and 4 may be combined to give

Jan 1, 1973

By K. Kim

INTRODUCTION A thorough evaluation of the geologic material being considered must be conducted to determine the feasibility of constructing a large-scale underground facility in a deep geologic formation. The design and construction of a nuclear waste repository in basalt, due to the unprecedented nature of the project, adds significantly to the need for thoroughness of this evaluation and mandates that geoengineering data and analysis be of the highest quality. The investigations required to collect the data encompass in situ measurements and observations, as well as laboratory and field tests. Mathematical (numerical) models, which are required to predict the long-term performance of the repository structure, must be developed to evaluate rock mass behavior at canister, room, and repository scale and eventual 1 y must be validated through in situ tests and monitoring. The information generated from these geo- mechanics investigations is essential for assessing site suitability and will be utilized in the development of the repository design, the engineered barrier design, and the evaluation of repository performance. The Hanford Site near Richland, Washington is one of nine sites throughout the nation being investigated by the U .S. Department of Energy as a possible location for the first high-level nuclear waste repository in deep geologic formations. The process of site characterization is currently in progress. If the site is nominated by the U.S. Department of Energy, an extensive program will be undertaken, the culmination of which will be a decision on the suitability of the site for waste disposal. There are a mu1titude of elements to the proposed site characterization

Jan 1, 1984

By John W. Padan, Thomas E. Howard

Most of what has been written during the past few years on marine mineral resources has emphasized the vast potential of the ocean, and its floor, as a source of the vital mineral raw materials upon which our modern technological society depends. Computations have been made to demonstrate that the sea contains sufficient minerals to support any reasonable world population indefinitely. The importance of these resources from the standpoint of strengthening the national mineral resource base has been pointed out. And though the information upon which these conclusions are based is sketchy, essentially qualitative, and often conflicting, there can be no doubt that the mineral potential of the sea is tremendous and that there are compelling reasons for working toward its exploitation. Unfortunately, there has been little emphasis on the problems that must be overcome, from the perspective of the economics of mineral production. Some of these problems have been noted, and some authors have appraised them realistically. However, many proposed solutions have been more romantic than practical, from the standpoint of both technology and economics. As a result the general impression has been given, particularly to those uninitiated in the realities of mineral production, that the mineral wealth of the sea is there for the taking-requiring only a good modicum of courage and technologic innovation to place it within easy grasp. But developing the capability necessary for substantial, profitable production of sea bottom minerals will be far from easy. It will be accomplished much more quickly if the problems are faced squarely, defined properly, and attacked in an orderly, logical sequence. While this approach may lack glamour, it offers the highest probability for success.

Jan 6, 1966

By C. W. Drury, E. J. Hall

The iron-nail method of assaying has been used for a number of years, but has not met with the approval of all assayers. The method possesses advantages which may be given as follows: (1) no preliminary treatment is required; (2) a lead button of proper size can be obtained; (3) it is economical. On the other hand, it has its disadvantages, which may be summed up as follows: (1) it is not applicable to ores containing large amounts of impurities other than sulphur, as practically all the base metals will contaminate the lead button ; (2) the slag is unsatisfactory in the larger number of fusions; (3) the method was known to give low silver results under certain conditions and the gold results were questionable. It was with the idea of determining the extent of this latter disadvantage that the following investigation was undertaken. It is well known that the fusion obtained in the lead assay is far more satisfactory than that in the " nails method" for gold and silver. The principal difference in the charges as a class is the presence of considerable reducing agent in the lead charge, and a limited oxidizing action in the nails charge, dud to PbO. The possibility of improving the nails fusion by simulating the lead charge was the reason for using argol in some tests, even though there were reasons for expecting this would have an objectionable effect on the results. Preparation of the Gold-Bearing Material. The materials containing gold and silver used in the following experiments were prepared rather than selected, in order to have a definite working product excluding undesirable elements. A high-

Jan 1, 1914

By Robert H. Richards

The adaptation of European methods of concentrating ores to suit the conditions of this country has followed the lines that simplify machinery, diminish labor and increase capacity. Noteworthy instances are the substitution of hydraulic classifiers for the last one or two trommels in the series, and the substitution of a distributing-tank for the slimes in the place of the Spitzkasten. The question may be fairly asked, At what point do losses become serious in consequence of these changes? It is to study this question that the investigation herein described has been undertaken. After the losses are located and the methods of stopping them are pointed out, it will then lie with the individual mill to decide whether or not the plans proposed will save suficient value to warrant their adoption. In the discussion of sorting followed by sizing, as the terms are used in this paper, me have to deal with the preparation of slimes by the Spitzkasten for subsequent washing upon the slime-table. The Spitzkasten, or pointed box, is an inverted hollow pyramid, generally of wood, usually with four faces or sides coming together in a point below. The sides can have, according to Rittinger, a minimum angle of slope of 50" with the horizontal. The feed-water carrying fine slimes (less than 0.01 inch, or 0.25 mm. in diameter) for treatment is fed at one end and carefully distributed over the whole width. The outlet is over the opposite end. The water-current passes direct from inlet to outlet, and has usually been regarded as a surface-layer pass-

Jan 1, 1898

By W. Allen

FOR the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree. Density Contrast: For a gravity survey to be successful, a sufficient density contrast must exist between the geologic feature sought and surrounding host rocks. Most mineralized areas will provide this contrast if fairly massive bodies are present. In the Bisbee area the entire sequence of formations, except for alluvium, appears to have specific gravities ranging from 2.65 to 2.70. These values have been determined by means of a large number of cut samples and diamond drill cores. As a further check, vertical gravity differences have been used where nonmineralized sections are known to occur.' The only known major gravity disturbances result from mineralization that has increased the density and the voids that have decreased density. The voids are caused by mining operations and by underground water movement that has developed several areas of caverns. Equipment: While not absolutely essential, a small rugged gravity meter, such as the Worden meter, is highly desirable. A tall tripod, about the height of a transit tripod, permits instrument set-ups in deep water and in locations where fallen timber and muck piles make it impossible to use a short tripod. An additional advantage of a tall tripod is that it places the meter in the center of the crosscut, reducing the error caused by the crosscut void. Size and weight are important, since the only satisfactory means of operating the meter underground is to carry it by hand. A backpack can be used in rare instances but is usually a hindrance because of the close station spacing. The operator's ability to move through tight clearances will improve survey coverage, as it is then possible to move through raises and caved areas and to pass mine cars and machinery with a minimum of trouble. Station Control: Gravity stations are normally located every 100 ft along the crosscuts, at each intersection, and in the face of all stub crosscuts. In areas of high gravity relief, or where small anomalies might be expected, stations may be located at 25 or 50-ft intervals. When possible, the stations should be offset to avoid effects of raises or other voids. The gravity stations on a level are tied to one or more base stations, which are usually located at the shaft or near the portal of an adit. The base stations may be part of a gravity control net that extends to each level in the mine as well as to the surface. Such a net extending throughout the potential area of the surveys is highly desirable, as it is then possible to compare all gravity stations on a uniform basis. The stations that are part of the base net should be carefully established by multiple readings and, if necessary, by a least squares adjustment of the loops. In some instances where levels do not have a shaft station, or where access may be blocked by caving, it may be necessary to establish secondary bases at the top and bottom of the raises that are between levels. Under fair conditions 70 to 90 gravity stations can be located and run in 6 hr by a two-man crew. The best field procedures depend on conditions. Reduction of Field Data: Most of the time required to produce a final gravity map is consumed in processing the data. Each meter reading must be corrected for a minimum of five factors that affect the gravity value in addition to the density contrast being sought. These factors are 1) instrumental drift, 2) station elevation, 3) topography, 4) latitude, and 5) regional gravity gradient. Mine openings, such as stopes and raises, will affect the value. However, it is seldom practical to make corrections for these voids. Usually a rotation is made on the field note on the station, and any

Jan 1, 1957

By N. S. Stoloff, K. R. Jordan

The temperatwe and grain size dependence of the mechanical avoperties of ordered and disordered Fe-49 pct Co-2 Pct V were investigated. The yield and flow stresses obeyed the Hall-Petch relationship u = ai + kd-&apos;I2. Ohdering reduced the intercept stress cjj and raised the Petch slope, k, at all temperatures. Ordering also increased the temperatwe dependence of k. The ductile to brittle transition temperature increased with order and grair~ size. Cleavage fracture was nucleation limited and the fracture stress did not zlary linearly with d-&apos;". A quantitative test of the Cottrell-Petch fracture theory (and recent modifications which consider the influence of slip mode), demonstvated that this theory is not applicable to FeCo-V. COTTRELL&apos; and etch&apos; independently suggested that a criterion for cleavage failure at the yield point, a,, based on dislocation pileups at a grain boundary or other obstacle to dislocat.ion motion, is: aYYkd&apos;I2 1 opy [ll or, equivalently, aikz,d112 +k:)bpy [2] where a, and ky are the Hall-Petch intercept and slope, respectively, 2d is the grain diameter, P is a geometric factor dependent on the macroscopic ratio between shear and tensile stress, p is the shear modulus, and y is the true elastic surface energy. When the product of quantities on the left side of the equation is equal to or exceeds that on the right, cracks should be able to nucleate and propagate at the yield stress, as shown schematically in Fig. 1. Therefore a high intercept stress, high Petch slope, or coarse grain size favors brittleness. petch3 associated the existence of a ductile to brittle transition in ferrous alloys with the temperature dependence of ai. One of the earliest modifications of the Cottrell-Petch theory was presented by ~rmstrong,~ who derived an expression for transition temperature in terms of several measurable flow and fracture parameters. The latter paper was able to rationalize situations in which the transition temperature increases with decl-easing grain size, as in the case of molybdenum,&apos; and also suggested that Ppy should be a function of grain size as well as temperature. More recently Johnston et a1.6 and Smith and worthington7 have suggested that the temperature or composition dependence ol&apos; ky must also be taken into account if there is any cha.nge in deformation mode, as from wavy to planar slip, or wavy slip to twinning, with change in temperature or solute content. Armstrong %as suggested that for hcp metals changes in o;k,dw> o;k,d1/2< / is / ^^^^ / / y_______________________________________ d-"2 Fig. l—Schematic representation of grain size dependence of yield stress, cry, and fracture stress, CTF. Intersection defined by Cottrell-Petch equation. slip mode should be incorporated in the theory through changes in the critical resolved shear stress for the slip system which controls ky. The purpose of the present investigation was to critically test the modified677 Cottrell-Petch theory of fracture in the superlattice alloy Fe-49 pct Co-2 pct V, by studying the grain size dependence of the yield and fracture stresses over a range of temperatures, in conjunction with an investigation of slip mode and fracture behavior. Previous work has shown that long range order results in a sharp decrease in flow stress, a small increase in work hardening rate and a drastic upward shift in the ductile-brittle transition temperature of F~CO-V.~&apos;~ The only comprehensive study of slip character in this alloy has been reported in a preliminary account of the present investigation.10 EXPERIMENTAL PROCEDURE The experimental work was carried out on material produced from a 10 lb vacuum melted ingot, of composition 49.32 wt pct Co, 2.09 wt pct V, balance Fe. 30-mil thick sheet samples with a 1; in. gage section were machined from cold rolled stock. The degree of cold work ranged from 85 pct for the finest grained samples to 5 pct for the coarsest grain size. Details of ingot fabrication are reported elsewhere." Equi-axed grain sizes in the range 12.7 to 75.4 p were obtained by annealing for varying times at 850°C. (Re-crystallization annealing time, rather than temperature , was varied to control grain size to insure that samples of all grain sizes contained equivalent quenched-in vacancy and interstitial concentrations.) Grain sizes were measured by the line intercept method on several specimens of each grain size. Following recrystallization, all samples were disordered by quenching into iced brine.

Jan 1, 1970

By E. W. McAllister

The decision of the California Oil Umpire&apos;s&apos; office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in thcir respective wells. Shortly therefter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clark and C. B. Kimberlint in a report2 dated March 1933. PRODUCTIVITY Index In the majority of individual well problems involving the use of subsurface- pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettlcman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time fur various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By E. W. McAllister

The decision of the California Oil Umpire&apos;s&apos; office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in thcir respective wells. Shortly therefter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clark and C. B. Kimberlint in a report2 dated March 1933. PRODUCTIVITY Index In the majority of individual well problems involving the use of subsurface- pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettlcman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time fur various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By J. P. Heller

The purpose of this discussion is to comment briefly on one of the points raised in the paper. The topic is that referred to in the Conclusion 2, in which the authors note a "disproportionate increase in mixing rate" as they proceed from a displacement performed at viscosity ratio 0.998 to one at 1.002. The recovery curve of this displacement, Fig.2A, shows a quite noticeable difference between the two runs in which displaced and displacing liquids were interchanged. This difference is ascribed by the authors to the change in viscosity ratio between the two experiments. This interpretation of the experimental results must certainly be based on rather precise measurements of the fluid viscosities or, at least, of the ratio of their viscosities. The ordinary Ostwald viscometer, employed in the usual way, is only just able to distinguish between liquids whose viscosities differ by two or three parts per thousand. The experimental refinements which then must have been necessary to measure with any precision a viscosity ratio of 1.002 would be worthy of mention. Indeed, one would have expected the authors to devote at least a paragraph to the display of this technique. For the same reason - to emphasize that the details of such unusually critical experimental work should be reported and discussed in the literature — I would have liked to see some comment by the authors on the requirements for temperature control during both the viscosity measurements and the displacement experiments. The temperature coefficient of viscosity of Soltrol C at room temperature has been measured in this laboratory at about - 1.9%/1°C. How much did the coefficients for the fluid mixtures used in the experiment differ from this and from each other Even if the two fluids were identical in this respect, it would appear that a temperature difference of .l°C between them in the flow system would produce a viscosity con- trast equal to that imposed by their composition. Reference to the experimental solutions of these problems would render Conclusion 2 more credible. Published theoretical work on the stability problem contains no indication of such extreme sensitivity to the viscosity ratio in the immediate neighborhood of unity. On the contrary, perturbation calculations such as those made by Chuoke1 and Perrine2 lead to initial finger growth rates proportional to the first power of the viscosity difference. The later instability growth calculated by Scheidegger,3 using the assumption of zero pressure gradient perpendicular to the average flow, is also simply proportional to the viscosity difference. The conflict regarding the sensitivity of the dependence of instability growth or mixing rate on the viscosity contrast needs explicit recognition in the literature. In particular, it would seem that the experimental work reported here should be supported by a more detailed description of the viscosity controls. Further discussion of possible alternative interpretations of the data would also be in order. For instance, is it possible that the unconsolidstted bead pack used changed its characteristics between the runs (due, perhaps, to the handling and inverting involved in the injection of the front) Or, are the data points of Fig. 2A averages from several runs performed in a series in which the two liquids alternated as displaced and displacing fluids? To summarize, it seems to me that the relationship asserted by Conclusion 2 in the paper needs the support of more detailed experimental evidence. REFERENCES 1. Chouke, R. L., van Mews, P. and van der Poel, C.: "The Instability of Slow Immiscible Viscous Liquid-Liquid Displacements in Porous Media", Trans., AIME (1959) Vol. 216, 188.

By M. Metzger, T. A. Read

The strengthening effects of hydroxide and synthetic plastic films in the creep of cadmium crystals were studied. The results were broadly consistent with the naive mechanical model. The dislocation-film reactions and the significance of the macroscopic stresses associated with certain films are discussed in the paper. ALTHOUGH a number of studies have been made of the strengthening of metal single crystals produced by surface films usually less than Ir in thickness, the mechanisms underlying this phenomenon are still not well established. Roscoe&apos; first noted the critical shear stress and the stress-strain curve of cadmium-crystal wires to be raised markedly by the presence of oxide films. Subsequent investigators2-&apos; have confirmed the effect for several metals and films including a number of plated poly-crystalline metal films. Harper and Cottrel1" with a thin film on zinc presumed to have formed as a result of etching and washing treatments) did not detect a strengthening at a rate of extension of 10 &apos; sec-&apos; although at lo-&apos; sec-&apos; the film raised the flow stress by 7 pct at 0.0005 extension and by 22 pct at 0.01. The marked strengthening at moderate strains thus appeared to be the result of a dynamical effect dependent on the rate and amount of plastic flow. Other observations&apos;. " are consistent with this view. The large effects of films on the tensile creep rate of single crystals were demonstrated when the observation of Andrade and Randall," that the creep rate of cadmium crystals increased on immersion in aaueous solutions of certain cadmium salts. was shown&apos; * to hold only when a film was present initially and was explained by the attack of the solution on the film and the removal of its strengthening effect. Changes in the creep rate interpretable in terms of the removal or formation of various films have been observed by other investigators.3,8,10,31 Certain other experiments have been reported in which surface films or liquid environments have affected the plastic behavior of metals, but these are not within the scope of the present work which deals with the effect of solid films on single-crystal slip. Possible Mechanisms—The film does not significantly reduce the load on the crystal in the elastic range (the elastic moduli of film and crystal are not too greatly different and the area of the film is so small that its share of the load is negligible) so that the initial operation of internal Frank-Read sources is not affected. However, as Fisher" has pointed out, a source terminating on the crystal surface requires only half the critical stress for activation as an internal source of the same length and a relatively strong film (even a very thin one) would pin the free ends of the surface sources so that, if surface sources are responsible for plastic flow in a clean crystal. such a film would increase by roughly a factor of 2 the stress necessary for generation of dislocation loops at a given rate. The other general possibility is that the film resists the passage to the crystal surface of internally generated dislocations. If the film is adherent and if the specimen is to exhibit slip of the same general character as a film-free specimen, the film must deform or fail in shear at the active slip planes. The naive mechanical model, where shear-stress relaxation across the active slip plane in the metal transfers load to the film until it deforms and slip can

Jan 1, 1959

By L. G. Jones

The objective of this paper is to present a better method for determining reservoir reserves of gas from extended drawdown test data. Means are proposed for conducting the test with or without the requirement of prior build-up to a static reservoir pressure. The test is based upon solutions to unsteady-state gas flow developed in an earlier paper and is believed to be superior to previous methods for determining reserves from flow-test data. The limitatiom of such tests are discussed, with emphasis on the subject of test duration. The test can supply useful information if the mechanics and limitations of it are understood. This type of information can be particularly valuable in deciding whether or not to drill offsets to producing wells. INTRODUCTION In the life of any gas or oil field, the engineer in charge must decide if certain wells need stimulation and whether or not to drill more wells in the field. Well production tests can aid in making these decisions. For instance, the value of stimulation can be estimated by determining formation permeability and the amount of well damage from drawdown or build-up tests. These tests are freely used in the oil industry. A less well-known type of analysis uses data from extended drawdown tests for determining reservoir reserves. Into this category fits the "reservoir limit test" of Jones,&apos;-3 and the "reservoir reserve test" presented in this paper. The chief value of these tests is their ability to "see" reservoir boundaries and thus prevent costly dry holes. Methods for determining reserves of both gas and oil reservoirs were proposed in the work of Jones. His proposals appear sound for single-phase liquid flow. The generality of his work on gas flow is open to question, however, since the analysis is based upon solutions to liquid-flow equations. The test for gas reserves presented here is derived from unsteady-state gas-flow solutions presented in a previous paper.&apos; In deriving this reservoir reserve test, it has been assumed that all of the reservoir energy is provided by expansion of the reservoir fluid and that the reservoir is radially symmetrical. No mention has been made of the effects of deviations from Darcy&apos;s law such as quadratic (turbulent) flow and well damage. Since the terms representing these effects are function of rate only, since the rate is constant and since the data are plotted in a differential form, it seems reasonable that these terms will not affect the test results in any way. No attempt has been made to estimate the effects of water drive, faults, or other departures from an idealized and isolated reservoir. For a qualitative discussion of some of these effects, the reader is referred to a paper by Jones3

By H. R. Brannon, R. J. Robinson, G. W. Kattawar

Accurate prediction of storm wave characteristics are needed for design of offshore structures. Statistical methods of random noise analysis provide techniques for predicting required wave properties. These techniques have been used to analyze and characterize storm wave profiles from Gulf of Mexico recording installations in 34, 65 and .98 ft of water. Correlations based on the results can be used to predict wave crest probabilities and wave shapes for a range of Gulf water depths and storm conditions. Example predictions of wave crest probability as a function of water depth for a particular set of storm conditions are given. INTRODUCTION Accurate predictions of wave crests and wave shapes are needed for design of offshore structures. With predictions of wave crests, platform deck elevations giving adequate protection from exposure to storm waves can be selected. Use of hydro-dynamic wave theories with the wave crest and wave shape predictions permits an estimate of the wave forces an offshore structure must withstand. Observation of ocean waves suggests use of statistical analysis for studying wave characteristics for water depths beyond the breaking wave zone; recent wave generation theories lend support to this approach. l-3 One of the most powerful methods of statistically analyzing wave profiles was introduced by Cartwright and Longuet-Higgins; most of the basic relations used were developed by Rice5.6 in studies of random noise theory. This method predicts wave crest elevation probabilities from two parameters characterizing a wave profile. The statistical approach also provides a means for predicting wave shapes. In the random noise model of a wave profile, surface elevation is represented as an infinite sum of sine waves with closely spaced frequencies and random phase angles. Power density is proportional to the sum of the squares of the amplitudes of sine waves having frequencies within a narrow band, and the distribution of power density as a function of frequency is called the power density spectrum, or power spectrum. The power spectrum characterizes an irregular sea, and hence finds use in motion studies of ships, barges and semisubmersible drilling platforms. From the power spectrum, a wave profile of any duration of time can, in principle, be calculated; this long wave profile depicts the many wave shapes to which a structure may be exposed. Thus, the statistical methods of wave analysis provide an approach to selecting wave shapes as well as wave crest elevations needed for design of offshore structures. For practical application of these techniques, power spectra and related quantities must be predicted from storm properties. Barber and Tucker 7 have reviewed correlations of wave properties and storm conditions. Their review summarizes work of Darbyshire,8 among others, in which a correlation of power spectra with wind intensity of the North Atlantic was developed. These results, plus more recent work by Pierson and Moskowitz and Kitaigorodskii,10 establish feasibility of correlation, but there is no theoretical basis for modifications extending the relations to other areas as remote as the Gulf of Mexico. Hence, to predict characteristics of Gulf of Mexico waves, a study of local observations is needed. This paper presents (1) a practical approach to computing wave profiles hat depict shapes of waves for use in force calculations, (2) a summary of relations for predicting probabilities of wave crest elevations, (3) correlations of parameters needed to apply these methods in the Gulf of Mexico and (4) examples of application of the techniques. THEORETICAL BACKGROUND The following sections summarize relations needed to calculate wave profiles and to estimate wave crest probabilities. These relations also identify quantities that must be related to storm

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952