Search Documents

By J. Rogers. K. L. Sutherland, E. E. Wark, I. W. Wark

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By J. W. Marx, R. H. Langenheim

The authors are to he complimented for a timely presentation of useful information concerning application of heat to oil reservoirs to increase the rate and ultimate recovery of oil. The solution for heated area resulting from constant rate injection of a hot fluid, presented by the authors, and the fluid-flow analogy, solved by Carter,' are particularly interesting in that 110 restriction is placed on the direction of development of the heated area. It is not necessary that the heated area grow radially. Thus the solution could provide useful information for heat injection in any type of well pattern with any specified swept area data. However, it was assumed in the development that the heated region would remain at a constant clevatcd temperature. Vertical heat losses were computed on this basis. Physically. the assumption that the heated region will remain at a constant temperature (independent of distance from the injection point) appears to require that the heat injection medium be stcam, or other condensible gases near the boding point at injection pressure. If a hot liquid below the boiling point or a hot gas considerably above saturation temperature were used, the temperature of the heated region would decrease with distance from the injection well. Lauwerier2 has discussed this problem for a linear system. (See also Jenkins and Aronolsky; and McNiel and Nelson.') Thus, the authors' solution applies more nearly to steam injection than to hot water injection or hot, non-condensable gas injection. Assuming steam as the injection medium, it appears that steam would pass through the constant-temperature heated region and condense upon contact with the unheated sand. The tempcrature in the condensing region would probably be governed by the release of heat of vaporization required for phase equilibrium at the existing pressure distribution. Temperatures in the region would also be influenced by vaporization of hydrocarbon. Thus, it is doubtful that an expression for radial temperature distribution based on heat conduction only (such as the authors' Eq. 9) would have practical significance. As pointed out by Marx and Langenheim, the growth of the heated area under constant rate steam drive will eventually be limited economically by vertical heat loss. The possibility of continuing to move heat economically by cold water injection or by increasing the steam injection rate appears to be a very important consideration. (Movement of liquids away from the injection well should increase injectivity.) Fortunately, the solution presented by the authors may be generalized to thc case of a variable heat injection rate. The general solution is:

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By M. Schussler, J. S. Brunhouse

Arc-melted and electron-beam melted tantalum in the cold-worked and the recrystallized conditions showed high strength, good tensile ductility, and excellent notch toughness down to 321°F. Arc-melted material, containing moderate amounts of interstitials, possessed better short-time strength than higher purity electron-beam melted material up to 2000°F. Cold-working substantially strengthened arc-melted tantalum, whereas electron-beam melted material exhibited a low work-hardening rate and possessed better formability characteristics. With identical compositions and microstructures, the mechanical properties of melted tantalum and uacuum-sintered tantalum should be similar. TANTALUM metal usage is increasing rapidly in a number of applications. The outstanding chemical corrosion resistance of tantalum accounts for its applications in chemical processing equipment for severe service conditions and for surgical uses in the medical field. The largest present requirements for tantalum are in the electronics industry, where its special properties are useful in capacitors. The high melting point (5425°F) and inherent ductility of tantalum also suggest that tantalum and tantalum-base alloys might offer an excellent combination of high strength at very high temperatures and good fabri-cability. Pure tantalum has been used in significant amounts in parts requiring high-temperature strength, such as heating elements, reflectors, and heat shields in high-vacuum high-temperature furnaces and in electronic tubes. A few very promising tantalum-base alloys have been developed and are being investigated extensively. The possibilities for tantalum as a high-temperature structural material, either unalloyed or alloyed, will become better defined when more extensive mechanical property data are known. pughl measured the tensile properties of vacuum-sintered tantalum in sheet form for the temperature range of 78" to 1500°K (-321' to 2240°F), and Bechtold reported data obtained at low temperatures.' Drennen3 determined creep and stress-rupture properties of both vacuum-sintered and arc-melted tantalum sheet at 1200 °F. Some additional data on the mechanical properties of tantalum at temperatures up to 5000 °F have been summarized elsewhere.4'5 It is probable that large structural shapes of tantalum, either unalloyed or alloyed, can most readily be produced from ingots prepared by melting. Consequently, the present investigation was undertaken to determine more extensive short-time mechanical properties of tantalum metal consolidated by melting. EXPERIMENTAL PROCEDURE Melting and Fabrication—Two tantalum ingots were utilized in this study to obtain information on the effect of interstitial elements on mechanical properties. Both ingots were melted from Union Carbide Metals Co. tantalum dendrites.

Jan 1, 1961

By S. F. Radtke, J. A. Snyder, R. M. Scriver

An automatic, continuous casting arc furnace employing a nonconsum-able electrode and a direct current arc has been constructed and operated successfully for titanium. A comparison of the properties of arc and induction-melted titanium indicates that where high ductility, formability, and toughness are required, arc-melted metal is preferable. BECAUSE of the reactivity of titanium metal with all known refractories and the common atmospheric gases, melting of the metal presents numerous problems. It is necessary to provide an inert atmosphere in the furnace as well as a crucible material that will not react with the molten metal, if a ductile ingot is to be produced. Two special furnaces have been developed that meet the requirements and one, the induction heated graphite furnace, has been described in some detail.' Little information is available for sizable units wherein power is applied to the melt through an arc, and the dearth of technical information on such a furnace prompted this report. It has been demonstrated clearly that arc melting produces titanium metal with superior toughness, ductility, and formability. To produce titanium ingots with these properties, an automatic, continuous casting arc furnace has been developed and is described herein. The history of arc melting may be traced to 1800, when Sir Humphrey Davy2 first experimented with Volta's electric battery and found that light could be produced and an arc formed between two carbon points attached to the cell. The discovery of the arc was followed by the design and construction of an arc furnace by Napier," in 1845, for the reduction of metal oxides. In 1853, Pichou' described a similar furnace, although it was not until the discovery of the dynamo in 1867 that the arc furnace could achieve commercial significance. In 1878, Siemens- esigned the first arc furnace intended for the melting of metals and by 1882 had melted steel and platinum successfully. . This was followed by Moissan's" classical work with the arc furnace in 1892. W. von Bolton,' in 1905, found that the arc furnace was suited admirably for melting refractory metals. In his work with tantalum, no suitable refractories for retaining the molten metal were found to exist. Together with Otto Simpson, he developed an arc furnace with a water-cooled copper crucible in which tantalum could be melted without contamination. This technique proved eminently successful. In his paper on the preparation of ductile titanium, Krolle first described an application of the von Bolton furnace to the melting of this metal. The

Jan 1, 1952

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore- guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. THE following question has been suggested for discussion: [t] "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.[t] Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possible the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1939

By R. F. Evans, J. M. Avert

Much has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this opera- tion is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft.— apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. Production of Magnesia from Dolomite In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime [CaO)., value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or advantageous. Essentially, the process is based upon the following series of reactions:

Jan 1, 1949

By R. F. Evans, J. M. Avery

MUCH has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of -magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore 'of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this operation is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft. apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. PRODUCTION OF MAGNESIA FROM DOLOMITE In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime (CaO) value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or

Jan 1, 1945

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By Ted C. Briggs

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent or in the locations required by modem agriculture. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. The organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until about 1913, when the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen, at high temperatures and pressures and in the presence of a catalyst, to form ammonia. At present Chile is the only country in the world with a nitrate mining industry, and, although the mining of natural nitrates is an important industry in Chile, natural nitrates are relatively unimportant, worldwide, because of the adoption of fixed nitrogen processes. The relative amount of the world demand for fixed nitrogen that is derived from natural nitrates has declined in recent years and will continue to decline. Modern farmers are sophisticated in economic calculations such as cost to benefit ratios and, for the most part, they purchase plant nutrients which give the highest return on their investment. Natural nitrates cannot compete on a fixed-nitrogen cost basis with anhydrous ammonia and its derivative products. In a limited sense, the fixed nitrogen industry is mining the air. Modern plants use air, water, and, in most cases, natural gas to produce the ammonia that is now the key building block of the fixed nitrogen industry. To present an accurate picture of the industry, this chapter on nitrogen follows a format somewhat different from that of other chapters in this volume.

Jan 1, 1975

Plans for the fall meeting of the AIME, to be held in conjunction with the Centennial of Engineering -marking the 100th anniversary of the Society of Civil Engineers-indicate that the Chicago gathering will be one of the most significant in Institute history. Headquarters for the six divisions represented will be the Palmer House. Twenty technical sessions will be held from September 3 to 6, with papers of industry-wide impact to be presented. The papers will follow the theme of the celebration-a century of engineering progress. The MBD will start the ball rolling with morning and afternoon sessions Thursday, September 4. A luncheon also will be held. MBD has scheduled morning and afternoon sessions for the following day as well. MGGD, Iron and Steel, and the Coal Div., will hold sessions Friday afternoon. The Industrial Minerals Div. plans an executive meeting, 5 pm, Friday. Geology Subdivision is slated for morning and afternoon sessions Saturday. The Coal Div. will meet again Saturday morning.

Jan 1, 1952

By B. K. Mozumdar

This paper describes the development and application of a dynamic simulation model of ground movement in an underground mine. Ground movement and related stress distributions with or without stowing are computed as the mining face advances. Pressure profiles plotted for different face positions indicate the presence of a front abutment with a maximum value of four times the original ground pressure but no back abutment in the gob. The surface strain is considerably reduced with increase in packing density in the gob up to a certain value. Beyond this value, the reduction in the strain is minimal, indicating an economic level of packing. As a result of model experiments with different physical systems and geological parameters, it has been concluded that when one of the coordinates for the subsidence and the strain curves is made dimensionless in terms of the critical width, the relationship will hold true for all physical situations. This was in agreement with the NCB observations for different panel lengths.

Jan 1, 1977

By B. Stoughton, H. O. Hofman

Before examining a fire-clay in the labori~tory for its resistance to heat or to fluxes, the sample is always ground to an impalpable powder. But when the clay is actually used for the manufacture of bricka, blocks, pots, etc., it is not ground to a uniform size, the particles varying from coarse grains to the finest slimes. The natural inference is that the tests with finely-ground substances mill give lower results than if the materials are tested just as they are going to be used. The, following experiments were made to find out how far this inference is justified. The method employed for fusion was Seger's direct method,* and, for fluxing, the modified Bischof method, described in the paper on that subject presented at the present meeting, The first question to be decided was, how large the test-cones ought to be made, to include representative proportions of the diflerentrsized particles colnposing the mixture. This was subjected to a screenanalysis with the following results :

Jan 1, 1899

By H. Maleki

Gob pressure measurements were made in a Western U. S. coal mine as part of a long-term program to evaluate cave progress and to determine the influence of geological discontinuities on caving conditions, load transfer, and resulting instabilities. Gloetzl cells were selected for the measurements due to their simple, robust construction and a history of being able to monitor pressures in a broken medium. A methodology was developed for the successful installation and protection of the cells and hydraulic lines in the gob as the face retreated. The measurements indicated a cave progress controlled by the frequency of major faults. The pressure-mining progress profile was compared to those observed in other parts of the world. It was concluded that the significant differences in profiles was caused by the thick-bedded strata, the existence of high lateral stresses, and the spacing between faults. Recommendations are given for future applications of Gloetzl cells for gob pressure measurements.

Jan 1, 1984

By G. Venturello, C. Antonione, G. Della Gatta

Results from work on the effect of inferstitials on recovery and recrystallization of' very pure iron (99.995 pet) doped with nilrogen up to 400 ppm are reported. Nitrided specimens were obtained by heating the iron in a static atmosphere of NH3 + H2. The samples were cold-rolled 80 pet, subjected to a series of isochronal and isothermal anneals, and submitted to examination by X-rays, micrographs, and hardness tests. Small additions of nitrogen show a strong effect in reducing recovery of' the mechanical properties of high-purity iron. At the temperatures of. the experiments, this effect proved greater than in the case of carbon. At 400°C pure iron recovers more than 50 pet of the total hardness increase, carburized iron vecovers 25 pet, and nitrided iron only 10 pet. On the other hand. the addition of nitrogen has, similarly to carbon, a very small effect on recrystallization; the effect is, however, slightly higher than that of carbon. When the concentration Of nitrogen is above the solubility limit in a iron at the temperattue of the experiments, an increase in the frequency of nu -cleation is also observed. THE object of the present work is to improve knowledge on the effect of interstitials both on recovery and on primary recrystallization of pure iron. In fact. at present there are no available data on the effect of nitrogen on high-purity iron. The only work which at present can be somewhat related to this problem is a work of Leak et al.1 in which grain boundary internal friction at high temperature in the presence of increasing amounts of nitrogen is studied by a torsion pendulum. The present work is a continuation of a previous one2 on the effects of carbon. EXPERIMENTAL PART Preparation of the Material. Pure iron was prepared following the same methods used in the pre- vious work2 and was nitrided using controlled quantities of ammonia in an apparatus similar to that used for carburizing. The apparatus consists essentially of a gas-tight quartz tube containing the specimens. The tube, maintained at constant pressure by means of a mercury seal, is placed in a resistance furnace. For nitriding, the NH3 + H2 atmosphere with a suitable concentration of NH3 was introduced into the tube, which had been previously carefully evacuated and degassed by heating at 600°C. The hydrogen used was carefully purified by passing it through a palladium filter. The ammonia required was prepared with the following reaction: CaO + 2NH4CI —CaCl2 + H2O + 2NH3 by heating the mixture of CaO and NH4C1 in a glass flask and then collecting the ammonia in a graduated Hempel burette. For each nitriding program a given amount of NH3 prepared by this method was introduced together with the H2 into the tube previously evacuated. Nitriding of the sample was then performed at 570°C for 48 hr. After this, to ensure a homogeneous distribution of nitrogen, the samples were further heated for 72 hr at 800°C. With this method which uses a static nitriding atmosphere, carefully controlled conditions of purity are obtained. Contrarily, with the conventional continuous-flow methods, using large quantities of circulating gas, there is a greater risk of introducing impurities into the samples. Furthermore, the required nitrogen concentration in the specimen is easily predetermined and obtained. A plot of the relation observed between the initial concentration of NH3 in the gas and the quantity of nitrogen introduced into the iron samples is given in Fig. 1. The data refer to samples of 1.2-mm thickness and to the nitriding conditions previously described. Furthermore, as a comparison, the data relative to two 0.5-mm-thick samples are reported. The presence of a reservoir in the cold zone of the reaction bulb made possible the gradual dissociation of ammonia on the sample in the hot zone. Internal-friction methods were used to determine the content of nitrogen dissolved in the iron samples. Some analyses were also carried out with chemical methods. The following table, Table I, shows a comparison of data obtained with chemical and internal-friction methods. The correspondence between chemical methods and internal-friction

Jan 1, 1964

By Elmer Weber, W. M. Baldwin

Solid lead obeys a single parabolic weight increase vs. time law. In contrast, liquid lead undergoes three successive parabolic weight increases vs. time laws, the first of which has a low constant relative to the latter two. The conversion times for the change from one parabola to the next decrease with increasing temperature. IN recent reports on the subject,1,2 it was noted that zirconium and titanium scale in air by a complex mechanism. The scale first forming on the metal is protective to the extent that it gives a low constant, K, for Tammann's, and Pilling and Bedworth's parabolic equation: w² = Kt [1] relating weight increase, w, due to chemical reaction of the metal with the air, and time, t. After hundreds of hours of apparent stability in some cases the first scale yields to another that offers little protection to the metal. This transition from one scale to another, from a slow parabolic oxidation reaction to a fast one, was not due to impurities in the atmosphere or incidental effects (changing environment, etc.) but was a specific behavior of the metal itself, the transition occurring at definite times (dependent on temperature) and showing other reproducible traits. In view of this behavior how can long-time service behavior be predicted from short-time laboratory tests, not only in the case of these metals, but in any case? Certainly a systematic study of the type of scaling behavior described above—wherever it is found—would help to answer this question. The present paper is a report on the behavior as it is found in lead—the only metal to the authors' knowledge for which the behavior has been described at all, if inadequately, for our present purpose.* At least four oxides of lead are known, of which one occurs in two allotropic forms. They are ß (red) tetragonal PbO stable up to 486°C;8 a (yellow) orthorhombic PbO stable from 486°C up to its dissociation temperature in air at about 2300°C;9 minium or Pb3O4 which from the dissociation pressure data given in Fig. 1 decomposes to PbO at 540°C in air; lead sesquioxide or Pb2O3,; and lead dioxide or PbO2 which, according to Fig. 1, decomposes in air at 400°C to minium. In view of the high dissociation temperature of PbO, lead will scale up to at least its boiling point. Further, it is known that oxygen is almost insoluble in liquid lead.'V his implies a fair probability that an oxide scale would not dissolve in the molten metal and would afford the same protection to lead in the liquid state as in the solid. All of the oxides of lead for which specific gravity data are available are more voluminous than an equivalent weight of metal or a lower oxide from which they might form, hence the scales will be in compression. Lead oxides are known to be ductile, so it would be anticipated that they would form coherent nonporous scales. It is not surprising to learn, then, that both solid and liquid lead scale according to the Tammann, and Pilling and Bed-worth law.14,15 (Gruhl states that at 600°C and above lead oxidizes linearly with time because of "spitting" of the scale.) The parabolic constants K reported by various investigators3,14-16 are badly scattered, however, as shown in Fig. 2. The oxides formed on solid lead were described as being reddish-brown but were not chemically identified by Pilling and Bedworth.15 Gruhl's descripdin³ of the appearance of the scales On his liquid samples indicates that a (yellow orthorhombic) PbO is formed initially on the specimens but gives Way eventually—at least at temperatures below 486 °C— to .ß (red tetraunal) PbO, and that below 540°C minium—Pb3O4 :is firmed at an even later time as an overlay on either the red or yellow PbO. Fig. 3 is a graphical interpretation of Gruhl's description. Gruhl does not indicate any change in the parabolic scaling rate as yellow PbO converts to red. He does indicate that minium reduces the scaling rate, al-

Jan 1, 1953