Search Documents

By C. K. Eilerts, J. D. Ham

Laboratory research has been conducted to evaluate the characteristic effects of condensate saturation on the mobility of gas in typical reservoir rocks. A pump with two pistons provided phases in equilibrium at controlled flow rates and constant liquid-vapor volume ratios. Core samples were tested in a holder that permitted sealing steady-state phases in the pore spaces under flow test pressures for weighing with sufficient precision to give an accurate measure of the attained saturations. Parameters of the study were pressure, apparent velocity, flowing liquid-vapor volume ratio, fluid composition, core material and length-to-diameter ratio. Tests were conducted at 515 and 1,515 psia to determine the effect of pressure on the mobility-saturation relationship. Influence of the apparent velocities 0.30, 0.15 and 0.07 cm/sec and of five liquid-vapor volume ratios from 0.0001 to 0.01 was determined at 515 psia The principal fluid system was nitrogen and and separator liquid from a Gulf Coast condensate, but the effect of a condensate of different viscosity was also determined. The significance of a possible concentration of liquid near the outlet end of the test cores was investigated. Core materials included a consolidated sandstone and a low-permeability limestone. Relative mobility and liquid-vapor volume ratio relationships are concluded to be dependent on pressure, saturation and, to a lesser extent, on velocity. For each porous medium and fluid there is a minimum saturation essential to two-phase flow, and high velocities of flow have only limited effect on saturations in this range. INTRODUCTION It is now recognized that knowledge of the availability of a reservoir gas — the period that gas may be recovered from a reservoir at a given rate — is as important as the estimate of gas in place. When reservoir conditions are such that pressure decline owing to production will result in retrograde condensation, liquid saturation can increase in the structure around the production well in a way that may restrict flow capacity, and hence future availability. l Based on a numerical solution of transient radial flow of single-phase gas-condensate fluids, 2 a program for computing the accumulation of condensate in a reservoir and the effect of this condensate on deliverability has been developed. During this development a need evolved for data that described the influence of pressure, velocity of flow and condensed liquid on mobility as recovery progressed. This paper presents the results of experimental investigation to obtain insight into the mobility relationship at reservoir pressures of gas-condensate fluids. A core holder for flow tests at reservoir pressure was developed to weigh the core and its fluid contents under pressure to determine saturation. A specially constructed pump was used to drive a two-phase fluid through the core until a steady state prevailed. The core was used as a differential device, and properties measured were intensive rather than extensive. APPARATUS Fig. 1 shows a schematic representation of the major pieces of equipment used in the mobility determination. The weighable core holder is connected to a two-piston, constant-displacement pump. Attainment of steady-state flow is indicated by stability of the flow differential read from the high-pressure manometer. WEIGHABLE CORE HOLDER An important part of the data needed was the mobility-saturation relationship. This required that mobilities and saturations be measured at pressures, flow velocities and liquid-vapor volume ratios characteristic of condensate reservoirs.

By P. Hazebroek, M. Prats, E. E. Allen

Well locations in water floods frequently do not coincide with the ideal well locations associated with the flood pattern which is used. A question of importance is. "How much oil is lost because of this?". This is the problem treated in this paper. It is assumed that each pattern in a five-spot flood has the proper number of production and injection wells but that the wells may be off-pattern. The distance by which a well is off-patern is given in terms of the pattern spacing, defined as the length of one side of a five-spot. The influence of off-pattern wells on the performance of a five-spot flood has been investigated mathematically for unit mobility ratio. All production and injection rates are assumed to remain equal. The loss in recovery resulting from pattern irregularitie: has been calculated at a cumulative water injection corresponding to a 98 per cent water-cut in a regular five-spot. Displacing a single production or injection well by about one-third the pattern distance reduces the total field recovery by 4.4/N per cent of the recovery obtainable with regular spacing, where N is the number of five-spots in the flood (assumed large). When off-pattern wells are separated by at least one regular five-spot and are displaced by less than one-third the pattern distance, the total loss in recovery in a large-scale flood is, at most, 1 per cent of the recovery obtainable from that field with a regular five-spot pattern. However, much higher losses may occur if the off-pattern wells are not separated by a regular five-spot, if the rates are imbalanced, or if the mobility of the injected water is higher than that of the crude. Although the loss in oil recovery due to pattern irregularity often may be low, the off-pattern case will always require injection of more water to reach the same final water-cut. The volume of water injected per unit volume of oil displaced has been calculated for each five-spot adjacent to a five-spot containing a single 08-pattern well. The cumulative water injection at the time of 98 per cent water-cut may be increased by as much as 37 per cent when a production well is displaced one-third the pattern distance toward an injection well. The existence of differences between actual subsurface locations and the idealized well patterns used in secondary recovery operations is well recognized. However, the methods commonly used for predicting waterflood behavior ignore such differences, even when subsurface locations are known. The reason for this is simple. The idealized well patterns are highly symmetrical and, as such, the production history of the pattern (and even of the field) can be determined from that of a few production wells—usually from only one. Consideration of the many irregular well spacings found in a specific field would entail a large amount of work, and then the results would be applicable only to that specific field. In an attempt to provide an answer to the more general problem, this paper considers a water flood having an idealized well pattern, except for one well which is not at its regular location. When several off-pattern wells are present, their contributions are assumed to be additive unless the off-pattern wells are close to each other. Only four positions of the off-center well (at x, y. of Fig. 1) are considered in this paper. These are shown

By E. H. Rennhack, J. F. Libsch

Definite transition behavior was found in unalloyed titanium at 0.13 pct 0 equivalent. The addition of 0.5 Sn, 1.0 Al, 0.5 Al, and 1.0 Sn lowers the tvansition temperature of titanium at oxygen equivalents exceeding 0.22, 0.29, 0.40, and 0.51, respectively. Metallographic evidence indicates that progressive amounts of oxygen restrict deformation at low temperatures resulting eventually in brittle fracture. The presence of tin or aluminum is thought to alter the atomic distribution of oxygen within the titanium lattice in such a manner as to facilitate some degree of slip and twinning. 1 ITANIUM-like iron and zinc experiences a transition from ductile to brittle fracture with decreasing temperature. The presence of sufficient quantities of the interstitial elements, carbon, oxygen, and nitrogen in solid solution, has been shown to progressively lower the room-temperature impact resistance of titanium with increasing interstitial content.1"1 Ogden,et al,2 reported finding no transition from ductile to brittle fracture with decreasing temperature in iodide titanium. However, a definite transition was found to occur at 0.36 pct 0 equivalent in an alloy containing 0.47 pct carbon in solid solution. The oxygen equivalent in this case was obtained by assuming the effects of carbon, oxygen, and nitrogen in combination on the impact properties of titanium to be additive on the same basis as their separate effects on tensile strength, namely: Oe = 2/3 (pct C) + pet 0 + 2 (pet N) They concluded that the tendency toward transition behavior is dependent on the total interstitial content in solid solution and not on any one particular interstitial element. Rennhack,4 however, recently found transition behavior in iodide titanium at an oxygen equivalent of 0.17 pct. Ogden, etal3, reported that the strengthening effects of carbon, oxygen, and nitrogen in titanium decrease with the addition of tin. They showed that tin additions increase the tolerance of titanium for the interstitials, that is, 10 pct Sn permitted individual additions of up to 0.4 wt pct of the interstitial elements without any significant loss in ductility. Aluminum tends to decrease ductility and impact strength of titanium for a given interstitial ~ontent.3 Van Thyne and Kessler5 found that the solid solubility of carbon in titanium doubled in the presence of 10 pct Al. The precise effects of tin and aluminum in the nrespncp of rorvfen nn the impact properties of titanium had previously not been determined. The high oxygen tolerance of titanium containing tin may provide a suitable means for improving the impact properties of titanium containing the interstitial elements, particularly oxygen. Unlike tin, however, aluminum has a high affinity for oxygen and will reduce rutile titanium dioxide (TiO2)by a thermit-type reaction.6 Thus, the atomic distribution of oxygen in titanium might be different in the presence of aluminum. The present work was undertaken to: 1) Determine the effect of oxygen on the transition behavior of unalloyed iodide titanium. 2) Determine the effect of small amounts of tin and aluminum on the transition behavior of iodide titanium in the presence of oxygen and other interstitial~. EXPERIMENTAL Three different lots of iodide titanium were employed to prepare the alloys studied in the present work. Their chemical composition is presented in Table I. The compositions of the tin and aluminum used for alloying are shown in Table 11. Oxygen additions were made using calcined rutile titanium dioxide (TiO2)of 99.7 pct purity. Alloy Preparation—Four titanium-base alloys containing separate additions of 0.5 and 1.0 pct each

Jan 1, 1960

By C. W. Merrill

The price records of seven representative mineral commodities for the 68-year period 1890 through 1957 have been compiled and analyzed for significant trends. When these records are reduced to real prices in terms of dollars of constant purchasing power or to the purchasing power of industrial wages at average rates, a substantial overall fall in prices is revealed. This downtrend contradicts the widely held concept that heavy drafts on a mineral resource must lead to scarcity, reflected in rising prices. Three metals (aluminum, copper, and pig iron), two fuels (bituminous coal and petroleum), and two nonmetals (sulfur and cement) have been chosen because of their pre-eminence in their respective categories, their significance in an industrial economy, and the ready availability of their price records. It might be added that these seven commodities were selected before any price figures were compiled; none was selected or rejected to substantiate any preconceived notions as to price trends. The overall importance of the seven is demonstrated by the fact that, taken together, they composed over three-fourths of the value of all minerals produced in the U. S. in 1957. The first step in the analysis was to reduce the price records to a basis for significant comparisons. Two such comparisons have been made: 1) The quantities of each of the commodities that could have been purchased for an average hour's wage in each year, and 2) the unit price of each commodity through the years in terms of deflated dollars. These data are set forth in the accompanying table and two charts. The quantities of the mineral commodity purchasable with the average wage for one hour's work in all manufacturing industries through 1926 were based on annual average prices and on average annual wage rates determined by Paul H. Douglas and published in his "Real Wages in the United States, 1890-1926." The series was extended through 1957 by the Bureau of Labor Statistics, U. S. Department of Labor. Calculations based on these data show that the average worker could have purchased 1.28 lb of copper with his hourly wage in 1890, whereas his hourly wage would have purchased 8.11 lb in 1957, an increase of 633 pct in the 68-year period. An average hour's wage would have bought 10.85 gal of petroleum in 1890, compared with 33.04 gal in 1957. Even more spectacular is the increase in sulfur, of which 25.25 lb could have been purchased with the 1904 average hourly wage; 223.08 lb were purchasable with the wage in 1957—an increase of 883 pct. Comparable price data for sulfur are not available for years earlier than 1904. For every commodity, the calculations show an improvement in the wage earner's purchasing power in 1957 compared with the early years. Measuring purchasing power in terms of wages does not give an entirely fair picture of the availability of a commodity in an economy. When the efficiency of an economy changes and the balance shifts among such elements as raw-material production, manufacturing, and service trade, the economic significance of an hour's work changes. Partly to meet such criticism, but mostly to present another interesting measure of the response of minerals to changing market conditions, a second set of calculations has been made to deflate unit prices for the seven commodities into terms of 1954 dollars. To accomplish this adjustment to a common 1954 parity, the Gross National Product Price Deflator, developed by the Office of Business Economics, U. S. Department of Commerce, was used. Although the results of these calculations are not as striking as those based on labor's increasing purchasing power, nevertheless the declines outweigh the rises in the prices of the mineral commodities. In terms of these deflated prices, aluminum and sulfur are much cheaper today than in the early years; copper was substantially cheaper in 1957 than in 1890; pig iron and petroleum are little changed; and only bituminous coal and cement have increased substantially. Strangely, the two mineral commodities with the strongest reserve positions are the two to exhibit rising real prices. Now this apparent overall downtrend in prices has taken place during a period of almost fantastic increase in the demand for mineral products. The value of minerals consumed in the world during the period greatly exceeds all mineral consumption up to 1890. A stage has been reached in the U.S. in which 95 pct of the energy used is of mineral origin and in which machines, structures, roadways, communication facilities, and most other elements in the industrial economy are primarily of mineral origin. Even agricultural fertility is maintained, in large measure, by mineral fertilizers. A series published in Minerals Yearbook shows that the value of U. S. mineral products has risen from $615 million in 1890 to $18,000 million in 1957, a 29-fold increase. Even in deflated dollars, the increase has been eightfold, while population has expanded less than threefold. Not only are demands of the industrial nations— the U. S., countries of Western Europe, and Japan— increasing at rapid rates, but those countries with agrarian economies are calling themselves underdeveloped and clamoring to industrialize. The ever-expanding mineral requirements in the U. S. and throughout the world show no abatement. Mineral reserves frequently have been described as wasting assets. Much concern has been shown for future users, who have been pictured as finding themselves on a plundered planet. Conservationists have viewed the future with alarm and have demanded legislation and regulations to reduce the drain on mineral reserves.

Jan 1, 1960

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By T. J. Whalen, S. M. Kaufman

Surface-tension measurements for liquid Fe-C-Co and Fe-C-Ni alloys were performed by the sesszle-drop technique at 1350o and 1425°C. Cobalt was shown to he more effective than nickel in lowering the surface tension of Fe-C alloys A minimum value for surface tension of 1640 dynes per cm was found in the Fe-C-Co system at a concentration of 1.5 pet C and 12pet Co. Analysis of these measurements in terms of adsorption and desorption behavior indicated that cobalt and nickel lower surface tension in Fe-C alloys by replacing carbon at the liquid-vapor interface. Comparison of results to date for Fe-C liquid alloys has shown that most substitutional-type elements having about the same atomic diameter as iron also have relatively the same influence on surface tension when present in dilute amounts. It has been shown previously that surface-adsorption behavior in liquid Fe-C ternary alloys is related to the manner in which the ternary addition affects the activity of carbon in the bulk solution.' Certain ternary additions, such as chromium, tending to decrease carbon activity cause adsorption of carbon and chromium to the liquid-vapor interface. Additions, such as silicon, increase the carbon activity, resulting in a desorption of carbon and an adsorption of silicon. Both cases were shown to cause a decrease in surface tension due to adsorption. It is the object of this paper, as part of the writers' continuing interest in the effect of alloying additions on the surface tension of Fe-C alloys, to present and discuss surface-tension data on solutions in the ternary systems Fe-C-Co and Fe-C-Ni. Available activity measurements for these systems in the solid state indicate a strong increase in carbon activity when either nickel or cobalt is added to Fe-C alloys.2, 3 EXPERIMENTAL PROCEDURE The alloy compositions used are shown in Table I. These alloys were prepared by vacuum melting in stabilized zirconia crucibles and then vacuum casting into cold-steel molds. The nominal analyses for the alloys used in this investigation are given in Table I. Surface tensions and densities were measured by the sessile-drop method4,5 in conjunction with the tables of Bashforth and bdams.' Specimens were prepared by slicing 1/4-in. cubes from the center of the vacuum-cast ingots and grinding the edges of these cubes until their shapes approximated spheres with flat bottoms. Proper handling techniques, including an acetone rinse immediately before use, assured minimum contamination from sources extraneous to the actual melting. For each experimental run a sample was placed on a BeO plaque and positioned and leveled inside a vacuum induction heating apparatus. The sample and plaque arrangement sat inside a molybdenum tube which acted as the susceptor. Diagrams of this apparatus may be found in the literature.= After heating to temperatures just above the liquidus at pressures of the order of 10-4 to 10- 5 mm Hg, photographs of the drop profile were made using its natural thermal radiation as a light source. Some measurements were made with partial pressures (-1 cm Hg) of a mixture of H2 and He gases. The H2-He atmospheres proved to be necessary at higher nickel contents to retard excessive vaporization losses. Chemical analysis for carbon and the ternary addition was performed for each alloy sample after completion of the experimental run.

Jan 1, 1964

By J. S. Aronofsky, J. P. Heller

This paper presents a mathematical analysis of the fluid mixing which occurs during flow through porous media. The analysis is based on the well-known diffusion equation with mass transfer term. It is pointed out that the use of this equation is justified by a single general assumption which does not specify any particular mechanism for the mixing process. Formulas are given for tracer fluid concentrations for two different boundary and initial conditions. Calculated numerical values compare closely with some published results of experiments in which no viscosity or density difference existed between displaced and displacing fluids. INTRODUCTION A phenomenological theory of the mixing and diffusion process is presented for the flow in a porous medium of two miscible liquids of equal viscosity and density. This is based on the classical diffusion equation which has been used to explain such processes as Brownian motion and heat conduction. More recently, this same differential equation has been derived (in a manner analogous to the work in this paper) for the problem of heat transfer during fluid flow in porous media.' The purpose of this paper is to show that the available experimental evidence justifies the use of this simple diffusion equation. The recent data of Koch and Slobod' and of von Rosenberg' are used to test this diffusion model by comparing concentration curve shapes and calculating "effective diffusion coefficients". The same differential equation for miscible displacement, as well as some experimental confirmation, has been published in Japan by K. Yuhara,4 and recently in this country by Day.5 Yuhara arrives at his con-clusions through analogy with turbulent diffusion, de- scribing the microscopic velocities in terms of "eddy motion" — although unlike the ordinary eddies of hydraulics. Day proceeds directly from Scheidegger's6 concept of the dispersion of velocities. After a very clear description of Scheidegger's theory, he applies it to calculate the motion first of a drop and then of a thin layer of brine into a bed of sand. For the latter case, Day derives and solves the same differential equation as Eq. 1. In our presentation no detailed assumptions are made as to the mechanism of displacement. In fact, several microscopic processes may well be involved—the only general assumption made is that their cumulative microscopic effect may be described by the addition of a second-order term to the differentirl equation of continuity. DERIVATION OF EQUATIONS Let us consider the displacement in one spatial dimension of Liquid A from a sample of porous media by Liquid B. A and B are assumed completely miscible and of the same viscosity and density. Both fluids are also assumed to be incompressible and it is specified that the total flow is the same for any cross section. It is evident that the rate at which Liquid B would be carried across such a section would be given by the product of the fluid velocity, u, and the concentration, C, of B in the fluid mixture assuming the constancy of u and C over the cross section. Since the volume of Fluid B is conserved, this leads to the one-way wave equation - u ?C/?x = ? ?C/?l where x increases in the direction of u—the "Darcy velocity", Q/A (or velocity flux per unit area), and 9 is the fractional porosity. Consider the case where fluid B is displacing Fluid A and the concentration distribution is represented by a step funcLon (with a vertical discontinuity). The solution of Eq. 1 predicts no mixing

Jan 1, 1958

By J. W. Evans

ONE of the most important and frequent calculations that the extractive metallurgist is called upon to make is that of the standard free energy change of a reaction (?F°). For many reactions of metallurgical interest, the lengthy arithmetical calculations have been eliminated by the use of free energy-temperature diagrams which have been constructed by Ellingham,1 Richardson and Jeffes,2 Kellogg,3 and Osborn4 (e.g., for oxides, sulphides, halides) from critical surveys of existing data. The speed and simplicity of making calculations with these graphs make them of great practical value and, this should be stressed, in the majority of cases no greater accuracy is obtained by the individual calculations from specific heat data, entropies, and heats of reaction. With the increasing industrial application of vacuum methods to the winning of metals, notably at present magnesium and the alkaline earth metals, it is necessary to calculate low metal vapor pressures above reaction mixtures. The existing free energy diagrams usually give values where the solid and liquid metals are at unit activity. To obtain the free energy change associated with the reaction Metal (solid or liquid) = Metal (gas) it is customary to calculate this from either vapor pressure equations or from the appropriate free energy functions. This paper presents graphically the free energies of vaporization of a number of metals of economic importance which can be used in conjunction with other free energy diagrams. Certain metals have been excluded on the following grounds: titanium, tungsten, molybdenum, and platinum have very high heats of vaporization and boiling points and the uncertainty of these values arising from difficulties of high temperature measurements makes free energy values of doubtful accuracy; the data for cobalt, vanadium, and zirconium are uncertain; finally, arsenic, antimony, and bismuth could not be conveniently included. because of the presence of mixtures of polyatomic and mona-tomic vapors in the temperature range considered. Free Energy Diagram In Fig. 1, the standard free energies of vaporization per mol (?F°T) have been plotted for the temperature range 0" to 2000°C for the reaction M (solid or liquid) = M (gas) The data have been obtained from the free energy functions — (F-H298)/T for the solid, liquid, and gaseous elements and the heats of vaporization at 298°K, i.e., ?H298 (vapor). The values of these functions have been taken without change from the recent critical survey by Brewer;' the bulk of this data is from Kelley7 with adjustments in the light of more recent work. Values of the function — (F-H298) /T at T = 298°, 500°, 1000°, 1500°, and 2000°K were employed. Where possible, a further independent value was obtained by using the boiling point, i.e., where ?F°T = 0. All calculations are based on the assumption that the metal vapors are monatomic and that the boiling points refer to those temperatures at which the partial pressure of the monatomic vapor above the metal is 760 mm. For the alkali metals, e.g., sodium, potassium, and lithium, diatomic gas molecules are present as minor species; details of these are discussed by Brewer." On the basis of the above values and allowing for the change in slope at the melting point, straight line graphs were constructed and extrapolated to 2000°C. The deviation from a straight line did not exceed ±500 cal, which in all cases appears less than the probable error in the ?F°T values.

Jan 1, 1954

By H. H. Rachford

This work presents a first-order analysis of the instability underlying viscous fingering in adverse viscosity-ratio water floods. It extends previous analyses of frontal instabilities, which were carried out with equations for parallel plate models, by including effects of the saturation transition zone observed behind the front in water floods in water wet systems. This zone tends to insulate incipient fingers from the high-mobility watet;. thus conditions for the onset of fingering differ from those in the parallel plate theory. Finite-difference solutions of the two-dimensional equations of displacement in porous media exhibited the predicted stability characteristics in six hypothetical field- and laboratory-scale floods in rectangular reservoirs. In contrast to results with parallel plate systems, this paper concludes that for waterwet reservoirs, laboratory models scaled by the usual criteria are also correctly scaled for frontal instability. Further, fingering in the systems studied can occur in any saturation range behind the front, and may occur at an intermediate saturation even though stability obtains both at the saturation corresponding to the Buckley-Leverett front and near residual oil saturation. Other points of contrast are that the likelihood of occurrence of fingering may not increase as flow rate or viscosity difference increases, but my be sensitive to changes in he relative permealdlity and capillary pressure functions. INTRODUCTION The recovery of oil by water flooding frequently involves displacing the oil by water of a lower viscosity. Displacement of a fluid by a less viscous one may lead to gross channeling or fingering like that observed in solvent floods, in which it severely lowers recovery efficiency.1 In addition to adverse effects on recovery, it has been suggested that the unstable move- ment causing fingering may interfere with interpretation of scaled model studies of proposed water floods, since the instability in the model might not be faithfully scaled to that in the reservoir prototype. In view of the serious implications of this possible breakdown of widely used scaled model techniques4-6 it is the purpose of this paper to examine the question further. Instabilities in the solutions of systems of differential equations imply a loss of smooth dependence on initial and boundary conditions. Thus, the possibility exists that in using models whose scaling is based on the differential system there may arise size- and rate-dependent factors which are not properly scaled. This possibility was examined in detail by Chouke et al., who analyzed the instability of frontal advance in a related problem, water-oil displacement in parallel plate models,2 in which a moving interface separates two regions of constant, unequal mobilities. First-order perturbation theory predicts the existence of a critical wave length for the growth of perturbations: and a wave length of maximum instability of A, = The interpretation is that wave lengths in a perturbation which are longer than A, will grow. Thus, if the width of a two-dimensional channel is greater than A,, fingers will grow, and the spacing of the fingers which grow at the maximum rate will be approximately It is important that the higher the velocity and/or the difference in flow resistance, the lower is A,, and thus the greater the number of fingers that can grow in a given model. In applying these conclusions to porous media, a pseudo-interfacial tension, , was assumed for the invasion front. Since this would not necessarily be equal to the liquid-liquid interfacial tension, an unknown constant was substituted for the foregoing expression for A, This was determined

Jan 1, 1965

By T. C. Wilson, Gerald Edmunds, W. M. Peirce, E. A. Anderson

Thirty-six elements have been alloyed singly with cartridge brass. Ammonia and mercury stress-cracking tests have been conducted on the as-rolled and recrystallized strip. Ultra high purity cartridge brass has also been tested. Silicon improves stress- cracking behavior. High silicon (I per cent) cartridge brass quenched from high temperature (for example, 800 C.) annealing is exceptionally resistant to ammonia stress cracking. This improvement is not lost by subsequent cold working, but is greatly reduced by subsequent low temperature annealing. Phosphorus, arsenic, barium, cerium, magnesium, tellurium, tin, beryllium, and manganese benefit stress-corrosion resistance under some circumstances, but not others. The other alloying additions tried had no large effect on stress-cracking resistance. None of the elements added accelerated stress cracking. The impurities in commercial brass are not responsible for season cracking.

Jan 1, 1945

By H. Doi, Y. Fujiwara, K. Miyake

In order to throw light on the mechanism of plastic deformation of WC-Co alloys, compressive tests of WC-(7 to 43) vol pct Co alloys have been carried out at room temperature, and stress-micro strain relation has been investigated in detail. The analysis of the factors affecting the yield stresses reveals that the yield stresses can be predicted by modified Oro-wan's theory if one properly estimates the planar in-terfiarticle spacings. Conzpressive straining of some of the alloys by 0.066 to 0.17pct increases the decrements by a factor of as much as 3.4 to 14, whereas the corresponding increase in the electrical resistivities is less than 10 pct. The analysis of the decrement data in terms of -Gramto and Lücke theory shows that the marked increase is attributed to increased dislocation darnping itt the binder (cobalt) phase. By cornbilling the decrement data and the conzjwession duta, one obtains the relation between flow stress in shear (?t) and increase in dislocation density (p): At = const . v6 . This is interHeted to mean that the mechanism of strain hardening of CirC-Co alloys is essentially sarne as the one for dispersion strengthened alloys. The possible effect of bridge formations between the carbide particles has also been examined. OWING to the combination of hardness, strength, and other physical and chemical properties, WC-Co alloys have opened the way for unique fields of applications, the recent ones being, for instance, anvils for super-high-pressure generation apparatuses. In such applications, the alloys are frequently subjected to very high compressive stresses: these stresses may cause the alloys to deform plastically and eventually to fail. However, much remains obscure regarding the nature of the plasticity of the alloys. Evidently, the alloys owe their high strength to the hard carbide particles which frequently occupy as much as 80 to 90 pct in volume fraction, whereas the ductility required for practical applications is provided by the small amount of the binder phase between the carbide particles. When the volume fraction of the carbide phase is not very large, deformation behavior of the alloys may be described by some of the current dispersion strengthening theories. However, greatly increasing the carbide phase is thought to lead to some carbide skeleton structure or bridge formations owing to the increased chances for direct contacts between the carbide particles;1,2 this may appreciably affect the plasticity of the alloys. Regarding the effect of formation of the carbide skeleton structure, it is interesting to note the work by Ivensen et al.3 on compression tests of the alloys containing somewhat large carbide particles; they observe extensive generation of slip bands in the carbide particles after application of some preliminary compressive stresses. They interpret the results in terms of plastic deformatiot: of the carbide particles which are supposed to have formed a skeleton structure; the binder phase plays only a passive role, at least in the early stages of the deformation. That carbide crystals exhibit microplasticity at room temperature is apparent from the work of Takahashi and Freise4 and French and Thomas5 on indentation of WC single crystals. On the other hand, Dawihl and coworkers6-10 maintain that even when volume fraction of the carbide phase is very large (for instance, more than 90 pet), a very thin binder layer generally exists between the carbide particles. They interpret the results of the extensive mechanical tests in terms of the plasticity of such a layer. Gurland and Bardzil11 point out that decrease in ductility of the alloys with increase in the carbide phase is caused by the effect of plastic constraint exerted by the dispersed carbide particles. Drucker12 further develops this concept from a continuum-mechanics approach on an assumption that a continuous thin binder layer separates the carbide particles. A common feature of the studies reported so far on the plasticity of the alloys is that the information deduced is invariably qualitative in nature. Thus, very few systematic experiments for obtaining reliable and sufficiently detailed stress-strain curves of the alloys varying widely in the microstructural features have been carried out. In particular, it may be of special interest to investigate in detail the early stages of the plastic deformation of the alloys in order to shed light on the strengthening mechanism. However, such work appears to be extremely rare. Doi et al.13 recently reported a first brief account of the results of some quantitative analysis of the plasticity of the alloys in terms of dislocation theory. Their experiment was rather limited in the composition range covered (volume fraction occupied by the carbide phase: 79 to 83 pct), and thus they could not necessarily elucidate the controlling mechanism of plastic deformation of the alloys of a more general composition range. Consequently, in the present investigation, deformation behavior and some other physical properties of the alloys were investigated and discussed in more detail over a much wider composition range. SPECIMEN PREPARATION WC-Co alloys used in this experiment were prepared in cylindrical or rectangular form by sintering in vacuo compressed mixtures of tungsten carbide and cobalt

Jan 1, 1970

By Harold A. Krueger

FACILITIES and mining operations of the National Lead Co., St. Louis Smelting and Refining Division, near Fredericktown, Mo., are situated in a famous mining area. Copper, lead, nickel, and cobalt have been mined here for more than 100 years, work having been started on a high sulphide copper outcrop in 1847. Lamotte sandstone is characterized by differential compaction on a rigorously eroded pre-Cambrian surface. The Bonneterre formation was therefore a good host for minerals not generally found in mineable quantities in these midwestern areas. Unusually complex minerals, however, make beneficiation difficult, and because of irregular ore thicknesses and elevations many engineers and operators have not attempted to mine the property. Others have tried who failed. This paper deals with economic, efficient, and competitive methods of mining these highly irregular orebodies, as compared to the open-stope, room-and-pillar methods normally used for horizontal-bedded lead deposits. For the purpose of this study it should be understood that the ore is found in two distinctly different types of occurrences, one to be designated as basin ore and the other as contact ore. Mining of basin ore is complicated by many faults, fractures, cross faults, and breaks. Contact ore is complex because it is found on flanks or slopes of pre-Cambrian knobs or highs. The dip of the mining floor for the latter type varies between 18" and 45". Occurrences of both types of ore are complicated by water courses or solution channels which carry unconsolidated shale, lime, sand, and dolomite. This material is also found between the bedding planes of the members of the Bonneterre formation. The water found where there are fractures, faults, and channels makes it very fluid and tacky, see Fig. 1, particularly after it has been blasted and handled by loading and hauling machines. Much of the ore can be wadded and thrown without dispersing. During early operations by the Buckeye Copper Co. in 1861 and the North American Lead Co. from 1900 to 1910, conventional narrow-gage railroad and side dump mine cars were used with hand shoveling. The complications of mining the contact ore, the only type attempted at this time, can be appreciated when it is realized that operators were obliged to use mules for haulage. Haulageways constructed on these slopes were of necessity similar to wagon trails or goat trails up the side of a mountain. In other words, it was merely a matter of going from side to side of the strike length of the slope, gaining a little in elevation on each shuttle trip. Production totaled only one to two tons per manshift. A few years later, about 1913, the property was purchased by combined Canadian interests known as the Missouri Cobalt Co., and the use of trolley locomotives was initiated. Between 1900 and 1928 a land agent using churn and diamond drilling methods prospected scattered sections of the area. In 1928 the first property was purchased by the present company, then operating as the St. Louis Smelting and Refining Co. Check drilling and prospecting was carried out by the company at various times between 1928 and 1939 to correlate the erratic mineralization. Much information about both types of orebodies was accumulated, but it was still questionable as to whether money should be invested to work these occurrences. In anticipation of high lead and copper prices, about the time World War II started, it was decided to develop and bring into production some of this ore. In 1942 No. 1 shaft was put down on the largest basin-type orebody and in 1943 No. 2 shaft was put down on contact-type ore. Operations were expanded when No. 3 shaft was completed in 1943, and progressed further in 1948, when National Lead Co. dewatered and opened No. 5 and 6 mines, old workings of the North American Lead Co. and the Missouri Cobalt Co. Because of the differential compaction of Lamotte sandstone over the pre-Cambrian porphyry, in some instances mineable thicknesses of basin-type ore occurred 20 to 30 ft above the sand. This is the exception rather than the rule, since most of the mineralization starts at the sand and is variable in thickness. The ore was attacked, therefore, by development drifts and crosscuts at the lowest possible elevation, where the ore immediately overlying the Lamotte sandstone could be drained and made accessible for mining. It was planned to connect to the drifts and crosscuts with raises to mine ore deposited 20 to 30 ft higher. The higher orebodies were thus mined as slusher levels. Slusher hoists were used to drag the ore into the raises, which were made into hoppers. The ore was then loaded into 32x32-in. ore cans, hauled to the shaft by battery locomotives, and hoisted by the conventional Tri-State method. The rate of efficiency was 5 to 6 tons per manshift underground. The contact-type ore was attacked in a similar way, except that the orebodies were not nearly so wide, so that they were more flexible for slusher loading into cans. This advantage was offset, however, by haulage complexities, since the railroad was constructed on steep slopes. Through experience and ingenuity, many improvements were made in mining both types of ores. The two levels, so-called, in the basin-type ore-bodies were connected as previously planned, more efficient locomotives replaced the older ones, and a

Jan 1, 1954

By Rodney L. Stone

In past attempts to characterize green and dry iron ore pellets, the authors have found large variations in the results of strength tests performed on closely sized pellets from the same batch. Where bentonite was the binder, such variations in the pellet quality were attributed to the presence of internal flaws and the nonuniform distribution of the binder. Studies have shown that pellet strength is strongly dependent on the degree of "mixedness" of the iron ore concentrate and the bentonite binder. However, before such a relationship can serve as a guide for the development of better mixing techniques and the associated economy of bentonite consumption, more precise knowledge of the bentonite-concentrate mixtures is needed. For example, what is the bentonitc distribution from pellet to pellet and within pellets?

Jan 1, 1970

By C. Le Neve Foster

The object of this paper is to offer a few suggestions for improving the mining and mineral statistics presented by the governments of various nations on both sides of the Atlantic. At the present time one may fairly complain of' two evils—lack of uniformity in some cases and want of completeness in others. The consequence is that the statistics are either less plain than they might be, or are useless for comparisons, or fail to present a faithful picture of the state of the mining industries of a country. The principal subjects upon which information is desirable are: the amount and value of the mineral products raised and the number of the mining population. With these data it is possible to form an estimate of the importance of the mining industries of any given

Jan 1, 1894

By AIME AIME

T'HE Columbia Section of the A. 1. M. E. took charge of the Western Mining Convention on Oct. 3, and the meeting was held under their auspices. W. L. Zeigler, chairman of the Section, called the session to order. The first paper on the program, "Lead Refining Practice at Bunker Hill Smelter," was presented in per-son by the author, A. F. Beasley, superintendent of the smelter. He pointed out the differences in the refining practice at Bunker Hill from other American refineries. The Bunker Hill plant was the first to adopt the liquation process for silver skims as developed in Australia. Details were given of operating practice with results. F. F. Colcord questioned the author in regard to the kind of metal best suited for kettles, which was said to be cast iron.

Jan 1, 1929

By R. E. Mazurak, E. L. Ealy

At the Beckley mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by wing a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1983

By Toshimitsu Kokubo, Yoshio Yamagata, Tadao Moro, Kenji Tomita

Owing to the traffic jam in collection, and transportation of wastes, the air- and water- pollution in incineration plants, and the sanitary trouble in reclaimed land, it seems that the defective existing system of the solid waste treatment in Japan can not follow the change in quality and the increase in quantity of solid wastes. Under these situations, the objective of the municipal solid waste treatment must be to actualize the pollution-free system for environmental protection and the resources recovery system for resource- and energy- saving. From this point of view, AIST of Japan is now engaged in the research and development of the resources recovery system from municipal solid wastes. This paper reports on the outline of the development of resources recovery technology in Japan, including the AIST's project on this matter.

Jan 1, 1976

By J. A. Rajala, R. W. Smith

The effect of increasing ionic strength, via monovalent and divalent ions, on alkyl sulfate flotation of hematite and quartz war investigated. The effects of collector chain length and pretreatment on this flotation were also studied. Sodium hexadecyl sulfate was shown to be a superior flotation collector to sodium dodecyl sulfate for recovery of hematite when there was no salt addition. Similar observation were made when sodium sulfate or sodium chloride was used to control ionic strength. Sodium dodecyl sulfate floated hematite better than its longer chutited counterpart under conditions of low pretreatment temperature and increasing calcium chloride concentration. The flotation recovery for all salt containing pulps was almost always improved after preboiling. Most of the results obtained when the pretreatment temperature was raised were attributed to increased solubility of the collector.

Jan 1, 1984

By John F. Havard, Armine F. Banfield

Sooner or later, we all get involved in the economic study and valuation of a mineral deposit. To communicate clearly the necessary information, we must scrupulously use various terms with specific meaning. All these terms-such as ore, exploration, development, production, reserves, proven ore, probable ore, possible reserves, resources, as well as similar terms applying to coal-are continually on the lips of anyone who reports on the economic aspects of a mineral deposit at the exploration, development, and production stages. The meaning of these terms is even more important in feasibility studies to determine whether a deposit should be put into production. Finally, careless use of these terms in reports published for public financing may, and sometimes does, lead to prosecution of the writer for misleading information.

Jan 7, 1975

Stringent controls now placed on the quality of coal make it important to be able to predict not only the tonnage and the grade of the coal in situ, but also the recovery factory and average grade after the coal has been washed. The established techniques of linear geostatistics (ordinary kriging) can be used to estimate the total tonnage and the grade of the coal in situ, but more sophisticated techniques are required for predicting the characteristics of washed coal. Two approaches are currently being investigated at Fontainebleau. One involves a parametric model of the washability curves and disjunctive kriging. This is described in Armstrong (1980(a) and (b)). The other is similar to the service variable approach used for estimating recoverable uranium reserves. The method is described in this paper.

Jan 1, 1985