Search Documents

By F. W. Newhall

DURING the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Browns-ville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to the chairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corpora-tion, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which are presented in this paper. Acknowledg-ments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication.

Jan 1, 1934

National Society of Professional Engineers has thrown its full sup- port behind pending legislation to appropriate $500 million for national conversion efforts that would provide employment opportunities for engineers, scientists, and technicians who are currently unemployed because of the decline in defense and aerospace programs. Known as the Davis-Giaimo bill, the proposed legislation would raise total Federal investment in science and technology to an adequate annual spending level and keep it proportionally equal to the growth in the GNP. If passed, the bill would increase and maintain Federal obligations for civilian-oriented research and development activities to a parity level with similar obligations for defense research development. U. S. Bureau of Mines has cataloged and placed on open file an inventory of U.S. coal deposits which can be economically strip mined at today's production costs. The costs include charges for reclaiming the mined land as required by 21 states. The report claims that some 46 billion tons of bituminous coal and lignite can be strip mined under present economic conditions, and that 32 billion tons of the total is classified as having less than 1% S. The report reviews strippable coal deposits by state, by county, by coal seam, by coal-seam thickness and by sulfur content. The report also gives an up-to-date summary of state laws on surface mine reclamation. Open-file copies of "Strippable Reserves of Bituminous Coal and Lignite in the U.S." may be consulted in Washington, D.C., at the Department of the Interior library and at U.S. Bureau of Mines offices in Pittsburgh, Denver, San Francisco. Dallas. Spokane, and Douglas Island, Juneau. Alaska.

Jan 1, 1971

By Alan Stanley

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—In the analysis of mill products containing minerals of appreciable difference in specific gravity the well-known principle of the method described by Stanley is applied in a number of ways for a variety of problems. The use of Le Chatelier bottle as explained in the paper may be a dependable and sufficiently accurate way, although no information is given as to the reproducibility of the specific gravity determinations. In the case of MacIntyre ore the method is applied for three separate products produced apparently without reagents and relatively free of fine slimes. Should it be applied for flotation products carrying a substantial amount of slimes, difficulties should be anticipated in the process of eliminating air inclusions from the sample. The difficulties mentioned above may be overcome by the use of a volumeter, an instrument designed for specific gravity determinations of finely divided solids in dry state. This instrument, see Fig. 4, is manufactured by F. Süffert-Bürner A. G. in Basel, Switzerland. Its operation is based on the law of Boyle and Mariotte. With the use of the volumeter, the specific gravities of test samples having a total volume of about 30 cm are easily reproducible within ±2 units in the second decimal of the specific gravity figure, and even better than that with utmost care. This accuracy is sufficient for ordinary operational control. How closely the specific gravity determinations follow the respective chemical assays depends primarily on the nature of the sample itself. In this respect no specific gravity instrument can give better results than those justified by the consistency of mineral distribution in samples analyzed.

Jan 1, 1954

By J. R. CAIN

SAMUEL L. HOYT, ? Nela Park, Cleveland, Ohio (written discussion?). The work that Dr. Cain is doing on gases in steel should have a highly important bearing on investigational work in connection with steel-making practice. We found, for example, in our work in connection with the use of manganese in open-hearth practice that we needed expressions for the manganese efficiency and the "condition" of the steel. To get these figures we assumed that we would need to know the amount of FeO at different stages of the heat and the amounts of the gases present. This required simultaneous analyses of our samples for FeO and the gases and Dr. Cain seems to be the only investigator who has considered the analytical work from this point of view. That he has done so is very encouraging and it is to be hoped that his work will solve the mys-teries now surrounding this neglected phase of steel metallurgy. Those interested in the Ledebur method for use in connection with the efficiency of manganese as a "deoxidizing " agent will he disappointed to learn that more recent work at the Bureau indicates that Ledebur determinations are not reliable. The principal source of error seems to be due to the partial reduction of the ferrous oxide by the carbon present in the steel. However, it seems like an unnecessary criticism of the Ledebur method to state (p. 1319) that it proved of little value because it showed little differences in oxygen for a series of steels treated with ,various reagents and showing variations in physical properties and free-

Jan 12, 1919

By M. J. Salkind

In order for fiber composite materials to find extensive use in structures, it is necessary to develop techniques for joining these materials. Riveting and adhesive bonding are two possible techniques which have been investigated although the former is less desirable because the low shear strength of most matrices makes this type of joint subject to bearing failure. Welding is an effective means of joining, especially for high-temperature applications where ad-hesives are weak; however, there are significant limitations placed on welding composite materials. The commonly used fusion welding techniques will find less use for joining composites because the two phases are often unable to stand exposure to such a stringent environment. In the case of eutectic composites, fusion welding will completely destroy the controlled microstructure. Solid-state techniques such as diffusion bonding offer potential success with certain design requirements placed on such joints. Since the primary mechanism of load transfer from matrix to fiber is shear parallel to the fibers, little load can be transferred across a butt-welded interface perpendicular to the aligned fibers. Successful joint designs must have a component parallel to the fibers to allow a shear area for load transfer. Configurations such as lap and scarf welds are likely to be successful. This note describes some results of experiments with diffusion-bonded joints in A13Ni whisker-reinforced aluminum. The composite material, prepared by unidirectional solidification of the A1-A13Ni eutectic, is described elsewhere.'-' It consists of aligned micron size whiskers in a matrix of aluminum. Since it has been shown that the microstructure of

Jan 1, 1969

By Stanley F. French

ELECTRICAL power and distribution for the sulphide ore plant is an addition and extension of the existing power system which has served the oxide reduction plant since its inception in 1914. The power plant is located at Tocopilla on the west coast of Chile, some 90 miles from Chuquicamata. A brief description of this plant and the existing transmission system is necessary to an understanding of the problems involved in the provision for the sulphide plant load. Originally the Tocopilla power plant consisted of four Escher Wyss turbines driving Siemens Schuckert generators, each rated 10,000 kw. At various times, units of 10,000 and 20,000 kw were added, all of which operated at 215 psi and 600°F at throttle. In order to improve the economy of the station, a Topping unit was installed in 1938 together with a high-pressure steam generator of 360,000 lb per hr capacity. This unit is rated at 11,000 kw and was designed for 750 psi, 880°F. The exhaust from this turbine passes to the low pressure station header for operation of part of the low pressure turbines. Total kw generated by the high pressure boiler, topping turbine and associated low pressure turbines totals 33,000 kw and the total station capacity is 113,000 kw. This installation proved one of the most successful of its kind, operating almost continuously. The original plant was of German design and consequently European characteristics were incorporated into the system, the frequency being 50 cycles and voltages of 500, 5000 and 100,000 were used for low, generator, and transmission voltages,

Jan 1, 1952

By Lytle Brown, Thomas C. Meadows

The rock now known to almost every Middle Tennessee farmer as " phosphate," was but recently recognized as such. The existence of a stratum of black siliceous rock in the hills surrounding the Nashville Basin has been known for many years to Dr. Safford, the State geologist. Nothing about it, however, would lead to the conclusion that it contains a considerable amount of bone phosphate of lime. The only feature that might attract attention is its very dark color; and since it occurs near the " black slate," one would naturally infer nothing more of interest to be connected with that feature than that this rock and the " black slate " derived their carbonaceous matter from a common source. Many of the country people have mistaken it for coal, or for an indication of coal; this impression being strengthened by the fact that, when a piece of the rock was thrown into a blacksmith's forge, a slight combustion was observed. As will be more fully explained, the phosphate-rock is of two kinds: (a) loose or separate boulders, occurring in a stratum of clay or blue shale; and (6) solid rock occurring in a continuous stratum. The boulders have been known for a long time as "balls," "kidneys," " stink-stones," etc. ; and as early as 1887, an analysis made under the direction of Dr. Safford, at Vanderbilt University, showed one of these boulders to contain 64 per cent. of bone-phosphate of lime. This information awakened no great interest in the matter, for the probable reason that at the same time it was known, or supposed to be known, that the boulder-beds were of limited extent as

Jan 1, 1895

By W. Robert Power

Dimension stone is considered by many the premium material for beauty and durability in institutional and monumental construction. Nonetheless in the United States it commands an ever decreasing share of the total market. At the beginning of the century dimension stone accounted for more than half the stone produced in the United States, but by 1974 it accounted for little more than 0.2% and the number of producing quarries and finishing plants had greatly reduced. This decrease in use is accounted for in part by competition from cheaper materials, but another factor seems to be the demand by many designers for uniformity and exact repetition of modular units in construction. Even where stone is used in large buildings modem architects want blandness of pattern and uniformity of color in the stone. Because most natural stone contains variations in color and pattern great strain is put on the quarriers to overcome this and produce a uniform product. This results in increased costs, increased waste at the quarries, and consequently increased price in the market. In spite of this, stone is still looked on as the most prestigious of building materials and its aesthetic appeal is born out by the many simulated stone patterns found in synthetic materials. End Use and Specifications The principal uses of dimension stone are in building construction and monuments. Other uses include flagging, curbing, paving, mill-stock slate, roofing slate, laboratory furniture, and refractory brick. Because many of these uses overlap, an orderly classification of dimension stone uses is most difficult. Various classifications have been used by Cumer (1960), Barton (1968), the U.S. Bureau of Mines yearbooks, and the Building Stone Institute (Anon., 1972).

Jan 1, 1975

By Edward W. Parker

Note.—The material from which this paper has been prepared was collected tor the U. S. Geological Suvey Bulletin, No. 316, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. Although the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in moat cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which constitutes a considerable percentage of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections -of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Jan 1, 1908

By M. C. Flemings, A. A. Tzavaras

Analytical and experimental procedures are descrihed for quantitative determination of volume-fraction microporosity in metals by mimorarlio-graphg. The analysis assumes spherical pores but allows for the observed fact that pores or portions of pores smaller than a given thickness do not project an image on the film. Volume-fraction microporosity was measuured in cast low-alloy steel and shown to vary from 0.6 x 10-4 to 10 x 10 depending on mode of solidification and on whether the material was air- or vacuum-cast. The aim of work described herein was to develop a method of quantitative measurement of the volume fraction of microporosity in cast metals. Microporosity, present in nearly all castings and ingots, is always interdendritic in nature and may be large enough to be seen on a polished surface with the naked eye. More generally, it is smaller in size, and its detection more difficult. Three techniques might be considered for measurement of microporosity: 1) lineal analysis of a polished metallographic surface, 2) density measurement, or 3) quantitative microradiography. As will be shown later, volume fractions of porosity in directionally solidified castings may be the order of 10-4 to 10-3; such small amounts of porosity are difficult to identify and measure on a polished surface. Density measurement is also not a suitable technique (for alloys) when the volume fraction of porosity is low. This is because the density of the base metal is often not known within the necessary accuracy, due to microsegregation or partial phase transformations. In general, it is not possible to completely eliminate microsegregation without also altering the porosity. Because of the limitations of the foregoing techniques, quantitative microradiography was employed to determine amount of porosity. In recent work, microradiography has been found to be useful for qualitative measurement of porosity, including determination of size and shape of individual pores;&apos;)&apos; however, quantitative determination of amount of porosity has not been attempted. I) CALCULATION OF VOLUME-FRACTION POROSITY The following analysis employs procedures similar to those of Cahn and Nutting3 and Hilliard.4 Major simplifications are that pores are assumed to be spherical and to be present in sufficiently small quantities that no overlapping occurs. A basic difference from the previous treatments is that the limited "sensitivity" of microradiography is considered. Assume first 1) cavities are spherical and of uniform diameter, 2) cavities are randomly distributed, 3) volume-fraction porosity and specimen thickness to pore radius ratio are sufficiently small that overlapping of the projected images of cavities is negligible, 4) sensitivity is limited (i.e., holes or portions of holes of less than a given thickness do not project an image on the film). The sensitivity, is defined as: where 5 = minimum thickness of void from which an image will be projected on the film and t = specimen thickness. Now, from Fig. 1, it is possible to distinguish between two different types of holes. These are 1) holes whose centers lie within the region t/2 > X > 6/2, where X is distance from one surface of the specimen (positive into the specimen), and 2) holes whose centers lie within the region (6 — r) < X < 6/2, Holes whose centers lie outside X = (6 -r) project no image on the film. These two types of pores are considered separately below. Type 1 Pores. When 6 is greater than 0, the image of a spherical cavity of radius r appears on the film as a circle of radius a which is smaller than r. From geometry, Fig. 1: a2=r2-52/4 [2] where a = radius of image of pore on film and r = radius of pore. Since the pores are randomly distributed and spherical V =4/3pr2Nv [3] where V = volume fraction of voids and Nv = number of pores per unit volume and the number of images of Type 1 pores per unit area of film, N&apos;A, is

Jan 1, 1965

By A. Lubinski, J. E. Hansford

Rotating drill pipe passing through dog-legs suffers fatigue damage due to cyclic bending stresses. Curves of the cumulative fatigue damage incurred in either steel or aluminum drill pipe going through Such dog-legs are presented. These curves provide means for properly planning the rate of angle build-up in directionally drilled wells and allow discarding of drill pipe which has been fatigue-damaged in dog-legs. INTRODUCTION Drill pipe which is subjected to bending as it rotates, experiences a cyclically varying bending stress. If this bending stress is sufficiently large, the drill pipe is fatigue-damaged by each revolution, and ages as fatigue damage accumulates. Drill pipe can be bent intentionally, as in the case of directionally drilled holes, or unintentionally due to unde-sired changes in hole direction caused by variations in formation properties, weight on bit, etc. These changes in hole direction, whether intentional or unintentional, are called dog-legs. The theoretical limits of dog-legs which are permissible before the drill pipe begins to fatigue can be calculated.&apos; However, in wells where the maximum permissible dogleg is exceeded, the concept of cumulative fatigue damage can be used to estimate damage suffered by the drill pipe. This concept has already been used to estimate the cumulative fatigue damage of drill pipe due to drilling vessel roll.&apos; The purpose of this paper is to extend the usage of the cumulative fatigue damage concept to drill pipe in doglegs, and to draw conclusions which may be beneficial in preventing numerous frustrating and expensive drill pipe failures. FATIGUE OF STEEL DRILL PIPE IN IDEALIZED GRADUAL AND LONG DOG-LEGS It is taken for granted that, if necessary, the reader will become familiar with the definitions and concepts which follow by examining the reference cited in each case. For Ref. 1, it will suffce to read only through the section Abrupt Dog-Legs. 1. Concept of the two extreme kinds of idealized doglegs: gradual and long dog-legs and abrupt dog-legs,&apos; 2. Concept of why the bending moment in drill pipe un- der tension is the largest in the vicinity of the tool joint,&apos; 3. Concept of why dog-leg severity which drill pipe can withstand decreases with an increase in tension,&apos; and 4. Definition of the rate of change of over-all hole angle (dog-leg severity)." Figs. 1 and 2 indicate the aging (fraction of life expended) of steel drill pipe passing through a gradual and long dog-leg. Both figures have a left-hand ordinate scale labled Length of Drill Pipe Below Dog-Legs. This scale can be used for cases in which the drill collar weight is applied to the bit and does not contribute to the tension in the drill pipe. It can be used for either 3 1/2-, 4 1/2- or 5-in. drill pipe. This is due to the fact that, if the drill collars do not contribute to the drill pipe tension, then the effect of pipe tension on bending due to a change in pipe size is nearly compensated for by a corresponding change in pipe rigidity. On the other hand, if drill pipe is rotated off bottom, then drill collars contribute to the tension in the drill pipe and this increase in tension is not compensated for. In this case, one of the three right-hand ordinates must be used (the one which corresponds to the correct drill pipe size). In the right-hand ordinates, tension should be understood as the weight in mud of the portion of the drilling string below the dog-leg, minus the weight on bit.

Jan 1, 1967

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.&apos; The damaging action of sulfur on the malleability of cobalt has not been generally recognized,&apos;; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By S. F. Frederick, W. A. Bailey

The relationship between microstructure and mechanical properties of cast 356-type aluminum alloys was studied to determine the cause of the variations in properties resulting from differences in solidification rate. It was found that variations in strength are a consequence of variations in ductility and that ductility is inversely proportional to the dendrite cell size. A mechanism is proposed to account for this correlation based on the fracture strain of the inter-dendritic silicon particles and the differential strain across dendrite cell boundaries. IT has long been assumed that permanent mold castings of aluminum are superior to sand castings because of their finer grain structure and reduced porosity.&apos; A systematic variation of static properties was noted during unpublished studies of fatigue-strength variations with solidification rate of A356-T6. Of particular interest was the observation that for a given composition and heat-treatment, both ductility and the ultimate strength increased with higher solidification rate. Because the A1-Si system forms the basis of many alloys used for castings and welding wire, a study was initiated to determine the details of how higher cooling rates improved mechanical properties of these alloys. The results of this study are presented here. EXPERIMENTAL PROCEDURE Specimens were prepared from 356-T6 to supplement the A365-T6 alloy data from earlier studies. This allowed a comparison of behavior of alloys with substantially different strengths but with only small differences in alloy composition. The composition and heat treatment of both alloys are given in Table I. The specimens were cut from a chill plate casting,&apos; which is a 6 by 9-in. plate, 1 in. thick, which has one end heavily chilled, and a large riser at the other so that solidification is essentially unidirectional from the chill end to the riser. Although not measured here, solidification times measured on similar specimens by embedded thermocouples are a few seconds at the chill end and up to 5 min near the riser. Specimens were obtained by cutting slabs from the plate, parallel to the chill; these represented different cooling rates, with essentially the same composition. For the tests, either 0.125 or 0.250-in. thick slabs were cut for standard 2-in. gage length specimens. The thicker specimens were tested to failure at 2000 lb per min while the thinner specimens were tested in an Instron machine at a constant cross-head speed of 0.02 in. per min. These thin specimens were intended for trans- mission electron microscopy. Some thin specimens were tested to failure while the remainder were given various amounts of prestrain. Dendrite cell sizes were measured by the linear intercept method on photomicrographs at either X100 or X50, depending on the cell size. It was assumed that the dendrite cells were outlined by the silicon particles. Determinations were made on two mutually perpendicular planes and an rms average taken. Electron fractographs of representative tensile specimens were made in the conventional manner using the two-stage replica technique.3 Samples for transmission electron microscopy were prepared by chemical milling followed by electropolishing. RESULTS AND DISCUSSION The results of the tensile tests and the dendrite cell-size determinations are given in Figs. 1 and 2. All data show the same trends, namely, a decrease in ultimate strength and elongation with increasing distance from the chill (and solidification time), and a corresponding increase in dendrite cell size. The yield strength remains essentially constant. The constancy of the yield strength was particularly significant since it indicated that variation in the solidification rate does not affect the stress required to initiate plastic flow. By plotting true stress-true strain curves as in Fig. 3, it can be seen that both

Jan 1, 1969

By F. W. Jessen, H. Kazemi

A washing technique has been developed to form a spherical cavity in massive salt. The technique is, basically, a process of controlling the fluid motion in the cavity, the concentration distribution of brine, the rate of dissolution at the walls of the cavity, and the particular settings of the wash pipe, or pipes (inlet and outlet pipe) employed. For a particular arrangement of tubing and casing, fresh water enters from the casing annulus at a position above the bottom of the tubing, and the dissolved material leaves the cavity through the tubing near the bottom of the projected hole. The initial configuration of the cavity is cylindrical, representing the drilled hole situated at the axis of the projected cavity. As washing progresses the original hole is enlarged radially (any direction perpendicular to the axis of the hole). An inert fluid (generally a hydrocarbon, natural gas, or air) which serves as a blanket is injected through the annular space between the original hole and the casing. The controlled downward motion of this blanket maintains the upper edge of the brine region that is expanding on the surface of the projected sphere. A large spherical glass container and a radial model were used to investigate the flow patterns and the concentration distribution of brine occurring during the progress of solution of the salt. Aluminum flakes and dye were injected and flow patterns were observed and recorded on motion picture film. Based on the results of these model studies and other work carried out in this laboratory, the controlled washing technique was formulated. INTRODUCTION Underground cavities leached in salt beds and salt domes have been used extensively for storing hydrocarbons. Little attention has been focused on the shape of the cavities as long as large volumes were obtained and the cavities were structurally stable. The general process involves circulating fresh water and removing brine. Two distinctly different circulating systems can be employed, each of which yields characteristically different shapes. By far the most generally accepted method of washing storage caverns in salt domes is the direct circulation system. Water is introduced through the innermost pipe of a concentric pipe system, and brine is withdrawn through the annulus. In the reverse-circulation method, water enters through the annulus and is discharged through the smallesc tubing string. The size of the operation, and hence the size of tubing and casing used, depends on such factors as cavity volume, length of hole, availability of water, disposal of brine and power requirements. Underground caverns are from 100 to 1,000 ft or more in length, and when completed vary from 40 to 100 ft in diameter, providing storage of 100,000 bbl or more. The volumes of water required per volume of salt removed vary from 6 to 7 for the reverse circulation method to 10 to 11 for the direct circulation method. Up to 80,000 BWPD are often circulated. In the direct circulation method, because water enters near the bottom of the projected cavity, solution of salt is greatest at this point, particularly in view of the fact that when the washing is begun turbulent flow undoubtedly exists in the immediate vicinity of the discharge of the inlet water. As the diameter of the hole increases, flow rates also are increased, so perhaps the condition of fluid turbulence is maintained for some time. During the later stages of leaching, when capacity of equipment may be the limiting factor in maintaining flow rates, there may still exist some turbulence adjacent to the point of influx; however, for the most part laminar flow conditions prevail. There appears, therefore, rather good evidence to indicate that the state of fluid motion is responsible for the typically shaped cavity which results from such washing — namely a cylindrical form, generally somewhat larger at the bottom than at the top. Depending on the number of so-called stages which might be employed, the walls or surfaces of the salt diminish rather uniformly from bottom to

Jan 1, 1965

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson&apos;s ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young&apos;s modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott&apos;s work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger&apos;s single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By Martin F. Littmann

FOR magnetic devices employing reactors with high rates of flux change very thin magnetic tapes have been employed. One of the more interesting of

Jan 1, 1957

By G. R. Pickett

Examples are presented which show that the velocity~ amplitude, attenuation and apparent frequency of several acoustic waves can be recorded in the borehole. Examination of such recordings, termed "character" logs, indicates that the wave types observed include a refracted compressional wave and a wave which travels with formation shear velocity. Laboratory data are used to show that compressional and shear wave velocities are dependent on porosity, effective stress and lithology; but that the change in reciprocal velocity per unit change in porosity is larger for shear waves than for compressional waves. We, therefore, conclude that. the accuracy of porosity determinations can sometimes be improved by use of shear wave velocities, provided that the shear wave amplitudes are large enough to delineate the shear arrival from the preceding compressional arrival on the character log. Borehole data are presented which show that the difference between shear wave and compressional wave reciprocal velocities can be used to predict porosities. This is a refinement which may allow the prediction of porosities from single-receiver acoustic logs without introduction of errors from borehole fluid traveltimes. Laboratory and field data are presented to show that the relationship between compressional and shear wave velocities can be used to indicate lithology. An example is presented to show that fractures usually cause a greater reduction in borehole shear wave amplitudes than in compressional wave amplitudes, an effect which may offer a more reliable means of detecting fractures. The complexity of the borehole acoustic wave train can rake presently available cement bond logs highly sensitive to the gate and bias settings used. The character log offers a means to circumvent possible misinterpretations by recording all amplitudes, from which the interpreter can select the appropriate data for evaluating the cement bond. Character logs may also be used as a quality control for open-hole transit-time logs when existence of small compressional wave amplitudes interferes with the proper functioning of bias-controlled timing devices. Evaluation of the potential uses of character log data is not complete; but a character log presented in a form convenient for routine use would be a desirable addition to currently available logs. To summarize, possible applications for such a log in formation evaluation include the following (1) quality control of transit-time logs, (2) refinement of porosity predictions, (3) determination of lithology, (4) improvement of fracture detection and (5) improvement of cement bond evaluation. Suggestions are made regarding the requirements for a suficient but practical character log for routine use. INTRODUCTION Acoustic logs have become a widely used porosity tool in formation evaluation. In addition, there is a growing application of acoustic logs in cement bond evaluation and fracture detection. These applications have mainly involved the use of logs of first-arrival transit times and amplitudes and have not included detailed studies of the complete signal. The purpose of this paper is to show that significant benefits in formation evaluation can be gained by a more complete use of the acoustic wave train generated in the borehole by an acoustic logging tool. We hope that this discussion will also stimulate further development of logs suitable for routine use so that these benefits may be realized. Examples of acoustic wave train logs, termed "character" logs, are presented to show that several identifiable acoustic waves are present in the borehole. The measurable characteristics of these acoustic waves and some of their relations to formation properties of interest are also discussed. The more obvious potential uses of character logs are listed, and some suggestions are made regarding the requirements for a sufficient but practical character log for routine use. CHARACTER LOGS Some 10 years ago, Vogel&apos; and Summers and Broding&apos; noted that the signals received uphole from an acoustic logging tool located in a borehole had a number of interesting characteristics. The logging tool consisted of two or more pressure transducers spaced on an acoustically insulated body (Fig. la). One of the pressure transducers was used as a transmitter to generate pressure waves in the borehole fluid. The other transducer served as a receiver to detect any pressure waves reaching it in the borehole. The receiver then converted these pressure waves to electrical signals which were transmitted to the surface and displayed on an oscilloscope as a record of time vs receiver-signal amplitude. Fig. lb is a schematic representation of a typical record. The interesting characteristics seen in the earlier&apos; and subsequent experiments were (1)

By C. F. Allen, G. B. Walker

The sink-float methods designated by heavy-media separation processes were pioneered by C. Erb Weunsch for the treatment of base metal ores as an improvement over jigs. The work of Weunsch was further developed by Victor Rakowsky and The American Zinc, Lead and Smelting Co. Early in the development of the processes, the inherent unsuitability of galena as the solid constituent of the medium was recognized and ferrous media amenable to magnetic recovery and control were developed. The high efficiency and low cost of magnetic recovery and cleaning of ferrous media regardless of particle size, slime contamination, or surfacial oxidation had led to the adoption of ferrous media by all of the sink-float plants operating under the heavy-media separation processes patents controlled by American Zinc, Lead and Smelting Co. Approximately 2,000,000 tons of base metal and nonmetallic minerals are treated each month by these methods. Heavy-media separation processes are a modern practical and economical adaptation of the well-known laboratory procedure for separating a mixture of two solids by immersing the mixture in a liquid having a specific gravity intermediate the specific gravities of two solids. The lighter solid floats while the heavier sinks. This method of separation has been attempted on a commercial scale, but the high loss and high cost of the organic liquids halted the development of the process. Many attempts have been made to simulate a heavy liquid by using a suspension of a finely divided solid in water. If the solid phase of the suspension is ground fine enough, the suspension can be made stable or so slow settling that a substantially uniform specific gravity can be maintained from top to bottom of the bath. However, any material separated by such methods will inevitably be contaminated by some slime which will eventually accumulate in the bath and cause a viscous medium at the expense of separating efficiency. Therefore, it is necessary to provide means for continually cleaning a portion of the medium to eliminate slime at the same rate at which it is introduced to the medium. The problem of efficiently cleaning the medium limits the minimum grain size of the solid of the suspension in the case of the Chance sand process for cleaning coal, because de-cantation is the only cleaning method available. If the sand is too fine, it will be lost along with the slime. Therefore, coarse sand must be used, and to maintain a semblance of a uniform suspension, it is necessary to use strong rising water currents. The combination results in a separation based more on hindered settling classification than on sink-float principles. As previously mentioned, galena was used as the solid constituent of the medium during the early stages of the development work. The high specific gravity of galena made it suitable for the preparation of medium for high specific gravity separations. Galena can be cleaned by either decantation or by froth flotation. As with sand, de-cantation limits the minimum particle size of the media that can be cleaned without excessive loss. Froth flotation for cleaning galena medium has been used, but the problem of floating fine galena that has been exposed to extensive oxidation is well known to be a most difficult one. Last year the largest heavy-media plant m the world, and the second plant to be installed, converted from galena medium to ferrous medium despite the fact that the ore contains galena which can be used as medium. The change to ferrous medium has been beneficial in many ways. Today all the heavy-media plants have been converted from galena to ferrous media. Unquestionably, ferrous media have the widest application of any media developed, for the following reasons: 1. Ease of recovery and cleaning by magnetic means. Particle size or surface condition not a factor. 2. Low consumption per ton of ore treated. 3. Resistance to abrasion. 4. Widest range of media densities, including higher workable densities (1.25 to 3.4) than have been found possible with nonferrous media. 5. Space required for recovery and cleaning of ferrous media is considerably less than that for nonferrous media. 6. Ferrous media require lower capital investment and operating costs for media recovery and cleaning. Advantages of Heavy-media Separation Processes Heavy-media separation processes offer the following positive advantages, amply demonstrated on a wide variety

Jan 1, 1950

By P. R. PaeIay, A. Slibar

Using three-dimensional, stress-deformation rate equations for a Bingham plastic, an approximate solution for the laminar flow of drilling mud between the drill pipe and casing is given for the case when the velocity gradients due to axial flow are large compared to velocity gradients due to rotation. INTRODUCTION The fact that drilling mud can be treated, to a first approximation, as a Bingham plastic has been established by several investigators12,3,4,5. A Bingham plastic is a material that is rigid until a certain combination of stresses exceeds a critical value. When the stresses are sufficiently high to initiate flow, the reduced stresses have a constant ratio to the corresponding deformation rates at each point. Prediction of pressure and torque requirements to produce the desired flow of the material have been made by analytical solutions due to Bingham6, Reiner7, and Buckingham8. One part of the present means of calculation that requires clarification is the flow between the drill pipe and casing. Present methods treat the flow resulting from the rotation of the drill pipe separate from the flow produced by the axial pressure gradient. Since the non-linear behavior of a Bingham plastic implies that solutions cannot be superposed, the present analytical investigation was undertaken to obtain a solution to the problem of combined axial and tangential flow. Equations have been proposed for the three-dimensional flow of a Bingham plastic9,10,11 and it has been shown that the proposed equations lead to the usual solutions from the one-dimensional theory". Applying these equations to the flow between two concentric cylinders the problem of axial flow only13 and tangential flow only12 have been solved. In addition to the separate problems of axial and tangential flow between concentric cylinders, the authors have determined the relationship between external torque on the inside cylinder and axial pressure gradient necessary to initiate flow". The solution given in Ref. 14 points out the complexity of the present problem. The problem considered here is the case of simultaneous axial and tangential flow. The axial flow, necessary to keep the drill bit free of removed material, results from the axial pressure gradient. Tangential flow is present since the drill pipe rotates in the hole. The solution given here is valid when the shear stresses in the drilling mud due to rotation are small compared to the shear stresses resulting from the axial flow. This case for laminar flow can be encountered in oilfield drilling. STRESS-DEFORMATION RATE EQUATIONS A detailed derivation of the equations governing the behavior of a Bingham plastic is given in Ref. 10. This section briefly outlines the physical reasoning leading to this three-dimensional formulation of the stress-deforma-tion rate law. Experiments on a certain class of materials have demonstrated the following properties: (1) when a certain combination of the stresses is below a critical value no deformation of the material occurs, (2) to a first approximation this combination of stresses is independent of the hydrostatic pressure (negative average normal stress), (3) if flow occurs the ratio of the reduced stress to the corresponding deformation rate is constant at each point of the flowing material, and (4) incom-pressibility. For the one dimensional case of shear deformation, Bingham6 formulated the governing equation as dxx, = 0 for sxx < to and µdxx = s xx = to for sxx to , . where dxx is the shear deformation rate, sxx the shear stress, to the critical shear stress, and p the slope of the sxx vs dxx curve for dxx > 0. Fig. 1 shows the behavior for pure shear between two parallel plates. Taking into account the physical properties given above and assuming the critical combination of stresses to be measured by the octahedral shear stress, the fol-lowing three-dimensional equations have been proposed.

Jan 1, 1958

By S. Weinig, E. S. Machlin

IN a previous study of the grain boundary stress relaxation phenomenon,&apos; the authors had arrived at the conclusion that two successive steps were involved in the complete relaxation of stress at a grain boundary. These two steps were grain boundary migration and grain boundary slip. It was further suggested that the slower of these two processes is rate controlling. In an attempt to ascertain the validity of the above, a study of grain growth kinetics on the same alloys used for the previous study was undertaken. Separate wire specimens, 0.030 in. diam, in the same as-deformed state (99 pct reduction in area) as in the previous investigation were heated to the various temperatures for a sequence of times. The compositions used and the temperatures of testing are summarized in Table I. A statistical determination of grain size was then made on each specimen, using the average length of traverse between boundaries as a measure of the grain size. Examples of typical results obtained are shown in Figs. &apos;1 and 2. The grain growth law D = ktn was found to fit most of the data. Using this relation, values of the grain growth exponent n were calculated and the inter -esting dependence of n on solute content shown in Figs. 3 and 4 was then obtained. Also, it was found that the constant K which was obtained from extrapolation is roughly independent of solute content. (K is uncertain to within ±25 pct.) An estimate of the activation energy for grain growth was made using the technique of Burke? This method utilizes the plot of the reciprocal of time necessary for the grain size to increase from a definite starting size Do, to a final size D, for each isothermal heat treatment. The slope of this curve corresponds to the heat of activation for the process. In Fig. 5 the rate of grain growth is plotted against the reciprocal of absolute temperature. The activation energies were obtained from these curves and are summarized in Fig. 6. Discussion It is interesting to note that the same saturation in the variability with concentration has been found for the grain growth exponent n in this research as was found in the previous researches on both grain boundary stress relaxationa and internal friction of dislocation origin." The significant feature is that saturation in the variation of these properties has been found to occur at about the same level of solute concentration, namely, between 0.1 and 0.5 atomic pct. The only characteristic common to these different quantities is that solute adsorption at grain boundaries and dislocation can take place and affect these values in a similar fashion. Thus, it is concluded that the grain growth exponent n depends upon solute adsorption at the grain boundaries. It appears, therefore, that theoretical considerations leading to the contrary conclusions5,6 have not treated the real process by which solute atoms exert their effect on grain growth. Prior to the analysis of the observed activation energies, certain of the aspects of the aforementioned grain boundary stress relaxation investigation will be briefly reviewed. It was found that with the addition of solute atoms the grain boundary stress relaxation peak (internal friction vs temperature) decreased in intensity. Simultaneously a second peak was observed which increased with increasing solute atoms. Both of these peaks were shown to be the result of grain boundary stress relaxation. They have been termed, respectively, poire peak and solute peak. It was suggested that the solute peak was dependent upon grain boundary migration, whereas the pure peak was a manifestation of grain boundry slip. Activation energies for both peaks were obtained as a function of Solute content. The value of the activation energy in the temperature range corresponding to the solute peak was

Jan 1, 1958