Search Documents

By D. D. Button, L. D. Jaffee

INTEREST in the use of graphite as a high-temperature engineering structural material has recently increased markedly. However, actual use of this material has been limited, in part because information about its high-temperature mechanical properties has been lacking. The information needed includes not only reliable values for the properties, but also how to control these properties. Malmstrom, Keen, and Greenl have reported on the tensile and creep properties of some graphites above 2700° F (1500°C). They observed measurable creep under tensile loading at 4000 OF (2200 °C) and higher, with elongations of about 7 pct at 4500°F. Their typical elongation-vs-time curve showed the normal three stages of creep found for many metals at elevated temperatures. The specimens used were heated by passing an electric current through them. This method of heating caused a significant difference between the surface and axis temperatures, and may have affected the results. More recent work by kattus, in which the specfinens were also heated by their own resistance, showed very little plastic deformation for either slow or fast tensile testing or for creep testing. Work at this Laboratory, already reported,3 showed that for temperatures above 4500 "F and under conditions of slow tensile loading some commercial graphites exhibited elongations up to 20 pct. The work reported here is the continuation of a study of the tensile creep behavior of some commercially available synthetic graphites at temperatures up to 5300°F, and is preliminary to a more systematic investigation of the variables governing the high-temperature mechanical properties of graphite. MATERIALS TESTED The tests were conducted on six blocks from four lots of synthetic graphite bearing four different commercial-grade designations. These blocks were selected because their tensile stress—strain properties had been determined in previous work.3 Table I pre- sents the available information, supplied by the producers, on the processing of these materials. Also included in this Table are the densities and the tensile strengths at room temperature and 4500°F determined by the authors. EXPERIMENTAL TECHNIQUE The furnace used to heat the specimens for testing is shown in Fig. 1. The heating element was a graphite tube, 3-in. OD by 2 1/2 in. ID by 24 in. length. A spiral was cut into the 6-in. center portion of this tube to provide a high-resistance sec-

Jan 1, 1961

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

By Adrian C. Dorenfeld

Laboratory data form the basis for the design of flotation circuits. These data, obtained from testing samples of the ore, should show the optimum con- ditions for concentrating the ore and the effects of change in process vari- ables. Among the more important variables commonly met in flotation practice are: Liberation Size-This is the particle size at which substantially all of the valuable minerals are detached from the gangue minerals. Reagent Additions- Experimental data will show the reagents used and their quantity, quality, and point of addition. Pulp Density-This is an important variable in the design of the flotation circuit because it is one of the factors determining the size and number of flotation cells. Flotation Time-The time necessary to make the separation into concentrate and tailing depends on such factors as particle size and reagents used and must be known for determination of the size and number of flotation cells in the plant. Temperature of Pulp-Temperature affects flotation reactions. Water at approximately room temperature is satisfactory for most flotation separations, but some minerals such as fluorspar are best floated in hot water. Type of Circuit-Many types of circuits can be designed, as discussed in detail later. The laboratory tests should provide data for design of the plant circuit best suited to the ore. Water-Knowledge of the quality of the future plant's raw water is important because water quality may drastically affect flotation results. If possible, flotation tests should be made using samples of the water to be used in the plant. Flotation results may vary with seasonal temperatures and with circulation of reclaimed water. Experimentation can show whether it will be necessary to provide for heating, cooling, treating, or reclaiming the water. Uniformity of Ore-The extent of variation of the ore in hardness, grind- ability, mineral content, and floatability should be investigated so that the designer can ascertain methods to overcome problems caused by ore variations. Settling and Filtration Data-To design the plant flotation circuits, settling and filtration rates and ultimate percentage solids of the various products must be determined. Corrosion and Erosion-Corrosion and erosion tests should be made on the flotation pulps, particularly if the pulps are acid or at an elevated temperature, so that suitable materials of construction can then be chosen.

Jan 1, 1962

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By Roman Šejnoha, Karel Mazanec

A pronounced tendency for delayed fracture zoas observed in the martensite structure of low-alloy steels in the as-quenched condition. Cracks of predominantly intercrystalline nature nucleated and propagated at stresses substantially lower than the short-titne tensile strength of- the steels, and were observed even in hydrogen-free speciunens. The occurrence of delayed fractures in the as-quenched condition is interpreted as a supevposition of the effect of free dislocations generated during the martensite transforlnation, and of a weakening of the prior austenite grain boundaries caused by dynamic shocks exerted on the boundaries by growing martensite plates. AN important metallurgical problem, connected with the production and use of high-strength steels, is delayed fracture in martensitic structures. Such fractures occur in quenched steels as a result of prolonged loading with external stresses far lower than the short-time tensile strength of the steel. The same effect can be produced by sufficiently high internal stresses: it is well-known that quenched structures will in some cases crack intergranularly at room temperature if not tempered quickly enough even in the absence of any externally applied stress. In Troiano's papers1,2 on delayed fractures in high-strength steels, the fundamental role of hydrogen migrating under the influence of multiaxial stress towards the nuclei of cracks was found. Fig. 1 shows the typical relationship between stress and the time to fracture found by Troiano in hydrogen-charged high-strength steels. On the other hand, Shurakov 3,4 explains the realization of delayed fractures in martensite as due to a "quasi-viscous" behavior of the austenite grain boundaries immediately after the martensitic transformation. 1) MATERIALS AND EXPERIMENTAL METHODS Two low-alloy steels of commercial purity were used for the experiments reported in this paper. Their chemical composition is shown in Table I. The heats were melted in a laboratory furnace, cast to ingots, forged to bars of 3/4 in. diameter, and annealed. Machined test pieces were heat-treated as follows: Ni-Cr-Mo steel held at 900°C for 30 min and quenched in oil; Mn-Si-Cr steel held at 900°C for 30 min and quenched in water. For the delayed-fracture tests, notched cylindrical test pieces, Fig. 2, stressed in torsion, and unnotched cylindrical tensile-test pieces, 1/4 in. diameter, were used. The specimens were normally loaded with a constant static load 45 min after quenching for the torsional tests and 10 min

Jan 1, 1965

By A. S. Nowick, C. Y. Li

It is deMonstrated that quenching from an elevated temperataupe accelerates the grain boundary relaxation in two solid solutions (aAg-Zn and a Cu-Al). This result is consistent with the proposal that, in solid solutions, grain boundary relaxation occurs by a mechanism of' self diffusion. Nevertheless, an alternative possibilitg, that quenching introduces vacancies into the boundary itself, must also be considered. THE phcnomenon of grain boundary relaxation has been well known for many years,1,2 yet the mechanism of this process is very poorly understood. One of the most interesting suggestions which relates to the mechanism of grain boundary relaxation was that of Ke,3 who claimed that the activation energy for grain boundary relaxation and for lattice self diffusion were essentially the same. The implication is therefore that the elementary step in the two processes is the same. This suggestion is particularly startling in view of the fact that activation energy for self diffusion along a grain boundary is very significantly lower than that for volume self-diffusion. Later evidence5-7 showed that there really are two grain boundary peaks, one which appears in high-purity metals, and the other (which develops at a higher temperature than the first) which appears in solid solutions beginning at solute concentrations in the range of 0.1 pct. Data for silver6 show that Kg's hypothesis is surely incorrect for the grain boundary peak in the high-purity metal, since it has an activation energy of only 22 kcal per mole, but that the hypothesis may still be correct for the grain boundary peak in various silver solid solutions, for which activation energies in the range 40 to 50 kcal per mole are observed. If the elementary step in the grain boundary relaxation process were the same as that for self-diffusion, it would be expected that the relaxation process could be hastened by quenching, 2.c. by introducing a non-equilibrium excess of lattice vacancies. Such a quenching effect has already been demonstrated in the case of another anelastic relaxation process, viz., the Zener relaxation effect. The Zener effect, which occurs in essentially all solid solutions, may be attributed to the reorientation of pairs of solute atoms in the presence of an applied shear stress,' and therefore must take place by means of a volume diffusion mechanism. The hastening of this process through quenching9 has been one way of demonstrating that atom movements in the lattice take place through a defect mechanism, presumably single vacancies. In order to see if the grain boundary relaxation is affected by quenching, it is particularly convenient to compare the grain boundary relaxation with the Zener effect, by choosing a specimen for which both relaxation effects appear. Specifically, a fine-grained sample of a solid solution shows in the curve of internal friction vs temperature, first a peak due to the Zener effect, then a second rise (and eventually a peak at substantially higher temperatures) due to the grain boundary relaxation. The same phenomena are also observable in static anelastic measurements, such as creep at very low stress levels. Thus, for the same fine-grained solid solution, the creepstrain, when plotted against log time, falls on a sigmodial curve with a sharp inflection point, due to the Zener effect, which is followed by a second rise and inflection resulting from the grain boundary relaxation. To look for a quenching effect, static measurements are preferable to the dynamic internal friction measurements, due to the fact that quenching effects tend to anneal out too rapidly at the temperatures at which the internal friction is measured.9 RESULTS AND DISCUSSION Creep experiments in torsion were carried out in an apparatus similar to that described by Ke1, whereby a wire is held under constant torque and its angular displacement is observed as a function of time. The alloy Ag-30 at. pct Znwas selected because of the large Zener relaxation that it displays. The two samples used were a "coarse grained" wire with a mean grain size about twice the diameter of the wire (diam = 0.032 in.), and a "fine-grained" wire which had several grains across the diameter. In Fig. 1 a comparison is made of the creep curves at 160°C of these two samples after they had been cooled slowly from 400°C. Curve A, which represents the coarsegrained sample, shows a unique relaxation process due to the Zener relaxation, with a relaxation time, T , in the vicinity of 100 sec. Curve B, which represents the behavior of the fine-grained sample, on the other hand, shows first the same relaxation process as that in A, followed by a turning up of the curve which corresponds to the onset of a second overlap-

Jan 1, 1962

By D. A. Augenstein, L. V. Amundson

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread, and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than 0.6 m (2 ft) thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disk filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disk filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some dif¬ficulty by the equipment. However, the problem has frequently been compounded after rains. The experimental program described in this paper tested the following methods of improving the load-bearing properties of coal refuse: moisture reduction, addition of crushed coarse refuse, addition of fly ash, addition of lime, and addition of a mixture of lime and fly ash. In terms of a balance between economic and technical considerations, the most effective method was demonstrated by laboratory and plant tests to be a 2% to 5% addition of lime. Test Program During formulation of a test program aimed at improving coal refuse stability, a number of treatment techniques were selected for evaluation of their effect on refuse load-bearing characteristics. The reduction of refuse moisture was the first technique considered, since moisture content plays a key role in the bearing strength of a bulk solid. The reasoning was that a very small reduction in refuse moisture, provided it could be accomplished with minimal effort and cost, would be sufficient for eliminating refuse disposal problems most of the time. At the same time, it was recognized that periods of rainy weather would offset moisture-reduction measures. Other techniques selected for evaluation because of their potential for improving refuse-bearing strength at reasonable cost were: addition of crushed coarse refuse, the addition of fly ash, and the addition of lime. A simple one-dimensional laboratory compaction test was designed for evaluating the effect of each of these techniques on refuse-bearing strength. Those techniques that gave best results in the laboratory would then be tested in the preparation plant in West Virginia. Laboratory Tests The laboratory test for evaluating each of the techniques involved the application of weight to a load module placed on a refuse sample in a container. The distance the load module sank with an increasing amount of applied weight was measured, and the relationship between module displacement and loading was obtained. The refuse container was large enough to minimize the influence of wall effects, and to decrease the effect of the container bottom, a test was terminated when the load module sank to about three fourths the depth of the container. Initially, an attempt was made to conduct compaction experiments with samples of total plant refuse. However, the presence of + 0.13 m (+ 5 in.) material in the refuse interfered with the mechanics of the test, and the large amount of material required for a representative sample made testing extremely tedious and time-consuming. To avoid this problem and because it was believed that only the fine components of the refuse were the major cause of the stability problem, tests were conducted with 13 mm X 0 (1/2 in. X 0) material from the total plant refuse. The equipment consisted of a 0.46 m (18 in.) cubic container, a loading module with 62 cm2 loading area, weights totaling 450 kg, and a portable concrete mixer for combining water and additives with the refuse. Refuse samples of about 110 kg dry weight were used for each test. Experimental compaction test data were evaluated by plotting the linear displacement of the load module vs. loading. During compaction tests, the vertical displacement of the load module was measured at each loading value. The plot of

Jan 1, 1980

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By G. E. Tardiff, A. A. Hendrickson

THE objectives of this communication are to present the solid-solution strengthening data for silver-base zinc single crystals and to evaluate the importance of strength contributions from several mechanisms through the use of this data combined with that for the silver-base aluminum case.' Some features of the yield point behavior of silver-base zinc crystals were previously reported.' Silver-base zinc alloys were prepared by induction melting 99.99 pct Ag with 99.9 pct Zn in high-purity graphite crucibles contained in argon-filled quartz tubes. After the first melting, the ingots were cut into short lengths, redistributed in the molds, and remelted in order to reduce solute-concentration variations. Alloy single crystals were then grown from the melt through the use of a modified Bridgeman technique which consisted of lowering the graphite crystal mold through a hot zone at a rate of 3/8 in. per hr. As in the melting operation, the molds were contained in argon-filled quartz tubes. Gage lengths 2 cm in length were introduced by both spark machining (circular cross sections) and abrading and acid etching (rectangular cross section) followed by electropolishing (a comparison of the critical resolved shear-stress values prepared by the two techniques showed no differences in strength values). The final cross-sectional areas of the crystals were approximately 5 sq mm. Prior to testing, the crystals were annealed at 600°C for 20 hr in argon atmospheres, furnace-cooled, and lightly electropolished. Crystal orientations were determined using the back-reflection method. The tensile testing was done on a Model FM Instron at a strain rate of 1(T4 per sec. Test temperatures of 77", 200°, and 400°K were attained by immersing the specimens in liquid nitrogen, dry ice-acetone mixtures, and silicone oil, respectively. The critical resolved shear-stress (CRSS) values for silver-base zinc crystals as a function of composition and testing temperature are given in Fig. 1. It will be noted that the CRSS for silver-base zinc solid solutions, as in the silver-base aluminum1 case, depends on temperature in a manner typical of fcc solid solutions: at high temperatures (-300°K and above), the CRSS is relatively temperature-independent but becomes strongly dependent on temperature at lower testing temperatures. A reasonable picture of solid-solution strengthening for silver-rich solutions at room temperature based on "direct" strengthening mechanisms3 is as follows. Since silver alloys have low stacking-fault energies, extended dislocations are expected and it is possible that Suzuki locking4 makes the major contribution to the room-temperature solute strengthening. This provides essentially temperature-independent strengthening since thermal motions of the dislocation line are not large enough to aid the dislocation in escaping the solute atmosphere extending over the fault width. An estimate of the

Jan 1, 1964

By J. S. Kennedy, G. L. Simard, A. A. Lefrew, C. M. Judson, R. B. Booth

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By J. S. Kennedy, A. A. Lefrew, C. M. Judson, R. B. Booth, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By K. A. Jackson, J. D. Hunt

The discussion by Tammann and Botschwar of the transition from eutectie grouth to denrdritic plus eu-tectic growth is reviewed and applied to metallic eutectic systems. Using expevimental data on the geowth rate of the Pb-Sn eutectic, and an extrapolalion of dendritic growth rate in tin and Sn-Pb alloys , qlcantitatice prerlictiotls of the extent of the eutectic region in tin-vich Sn-Pb alloys are made. There are no experimenta1 measuvements available for detailed comparison with these predictions. EUTECTIC structures form over a small range of compositions. The theory of lamellar growth presented by Jackson and Hunt' indicates that it is in principle possible to have eutectic growth over almost the complete range of compositions between the two solidus lines. This does not occur in practice. Alloys far from the eutectic composition grow dendritically followed by a eutectic as shown in Fig. I. The transition from a eutectic to a dendritic plus eutectic interface cannot be predicted from constitutional undercooling arguments because constitutional undercooling always exists ahead of the eutectic interface.' Reasonable predictions can, however, be made using arguments originally put forward by Tammanl. and Botschwar.3 These and later workers'"*6 carried out extensive experimental investigations of the extent of the eutectic range in organic materials. They concluded that the structure formed, eutectic or dendrites plus eutectic, depended on which structure grew faster at the given undercooling. This is, of course, equivalent to the structure which grows with the smallest undercooling at a given growth rate. In this paper, we will discuss these ideas briefly and then apply them to predict quantitatively the range of eutectic growth in tin-rich Pb-Sn alloys. The temperature dependence of the growth rates of dendrites and eutectic for a typical metal alloy of eutectic composition is shown schematically in Fig. 2(a). The growth rate for the eutectic increases more rapidly with undercooling than those of the dendrites because of the short diffusion path maintained in the eutectic, see Fig. 1. For an alloy off the eutectic composition on the A-rich side, the growth rates shift as shown in Fig. 2(b). The liquidus temperature of the a phase increases, that of the 3 phase decreases, and the temperature of zero growth rate for the eutectic does not change. The curves, particularly the dendritic ones, change shape as well, but for our purposes the principal effects occur because of the change in liquidus temperatures.3-6 In an isothermal system, only a dendrites will grow above TE, Fig. 2(b). If the temperature is below TE, and both phases have nucleated, a dendrites will grow ahead of the eutectic at

Jan 1, 1968

By J. S. Kennedy, A. A. Lerew, C. M. Judson, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from. these laboratories." These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that, are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren, machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as. the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite. flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the. selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pet Zn for ZnS) ; and the quartz from Klondike, Mo., analyzed as 99.97 pet SiO2. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from S82 supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1952

By M. T. Simnad, G. Derge, Ling Yang

STUDY of diffusion in molten substances is important in at least two respects. Diffusion data, combined with thermodynamic and kinetic information, throw light on the structure of the liquid state. Moreover, a knowledge of diffusion coefficients and their temperature dependence is useful in ascertaining the controlling step in many metallurgical reactions. Although diffusion measurements have been made on a number of molten salts, slags, metals, and alloys,'-'" the results available are still limited and widely scattered, especially for the high temperature melts. It is the purpose of this investigation to establish reliable procedures for the measurement of self-diffusion coefficients in high temperature melts and to use these procedures to determine the self-diffusion coefficients of iron in molten Fe-C alloys of different carbon contents. Experimental Measurement of self-diffusion coefficients in high temperature melts is usually carried out by using one of two methods. In the first, diffusion takes place between two cylindrical samples of the same material, one of which is made radioactive. The diffusion coefficient is calculated from the radioactivity penetration curve in the solidified sample after the diffusion. In the second method, samples contained in capillaries of an inert substance are immersed in an infinite reservoir of the same material. Either the material in the capillary or that in the reservoir is made radioactive and the diffusion coefficient is calculated from the change of the radioactivity of the sample in the capillary after the diffusion. The second method is simpler because a radioactivity penetration curve is not needed for the calculation of the diffusion coefficient; however,.it is valid only when no convection has occurred in the capillary during the diffusion. A radioactivity penetration curve is therefore always useful in indicating that the required conditions for the diffusion are ful- filled. Towers and Chipman" recently studied the self-diffusion of calcium and silicon in CaO-Al,O,-SiO, melts by using the capillary method. Instead of measuring the change of the radioactivity of the sample in the capillary, they autoradiographed the sample after the diffusion and calculated the diffusion coefficient from the intensity distribution of the autoradiograph. Their method is useful when the radioactive isotopes are weak ß-emitters, but is very difficult, if not impossible, to apply to cases involving strong ß or y-emitters. For such cases, sectioning of the sample according to the method of Morgan and Kitchener' may be used for the construction of the radioactivity penetration curve. The self-diffusion of iron in molten Fe-C alloys has been studied in this manner and the experimental procedures are described as follows: The diffusion apparatus is shown schematically in Fig. 1. The bath consisted of about 200 g of an Fe-C

Jan 1, 1957

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally.' Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan,3 show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision; using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by, the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.5 However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: [3fB = 9.20•'./V•Vn- (n-1) • (n+2) /8[1]] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts' as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of, a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsymmetric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat I than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system, of one degree of freedom can be applied: [1E/m[2] fP = 27] Here f, is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: [t~ = 2/f = 7r\/m/E[3]] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson' 1831) [aP = 4 D2.pL•g•h +7rD•y sin a[4]] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, pL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of-the liquid in cm, y the surface tension in dynes per cm and a the supporting angle' or the one required to insure equilibrium, a being smaller than the contact angle ?. Although demonstrated by Poisson, it has not

Jan 1, 1952

By R. E. Smallman, I. Milne

The deformation behavior of single crystals of Nb-Mo alloys has been investigated with particular reference to the influence of composition, orientation, and temperature. Strong solid-solution hardening was observed reaching a maximum at the equiatomic cotrlposition and can be attributed to the difference in atomic size between niobium and molybdenutrz. Changes in the form of stress-strain curve, as shown by a high work-hardening rate and restricted elongation to fracture, were observed at a composition of Nb-85 pct Mo and are attributed to the presence of MozC DreciDitate. Conjugate slip was only extensive in dilute alloy samples; at the 50/50 composition deformation rnainly occurred by primary slip, and the onset of conjugate slip gave rise to failure by cleavage on (100). The variation of yield stress of Nb-50 pet Mo with orientation was consistent with slip on (011)(111) slip systems. The temperature deperndence of the yield stress between -196" and 250°C was similar to that of pure bcc metals, but at a much higher stress level; no evidence for twinning %as found. IN recent years the deformation behavior of various pure metals in groups VA and VIA has received considerable attention, but surprisingly little work has been carried out on binary alloys made by mixing metals from the two groups. Such an investigation would be of interest since single crystals of metals of group VA have been shown to deform characteristically with a multistage deformation curve1"3 while a parabolic type of deformation curve has been reported for most of the group VIA metals.4'5 It has been suggested by Law ley and Gaigher~ that the difficulty encountered in obtaining multistage deformation curves for molybdenum in group VIA was possibly because of the presence of a microprecipitate of MozC which they observed even at carbon contents as low as 11 ppm. Recently a multistage deformation curve has been reported for molybdenum ," although the stages are not so definitive as those for group VA metals. The binary alloys of the particular refractory metals which have been investigated in single-crystal form include Ta-w,' Ta- Mo,' and Nb- Na." While a large amount of hardening was observed for alloys of the Ta-W and Ta-Mo systems, associated with room-temperature brittleness for alloys approaching the equiatomic composition, Ta-Nb remained ductile over the complete composition range with little or no solution hardening. Other systems have been investigated by hardness measurements on polycrystalline material and a discussion of the hardening of these alloys has been presented by ~udman." The purpose of the present investigation was to examine the deformation behavior of Nb-Mo alloys in detail, with particular reference to alloy composition and single-crystal orientation. In this way it was hoped to shed some light upon the restricted ductility of these alloy specimens. 1) EXPERIMENTAL PROCEDURE The starting materials were obtained in the form of beam-melted niobium rod and sintered molybdenum rod of suitable dimensions. Since niobium and molybdenum form a complete solid-solution series at all temperatures, alloy single crystals were produced by melting the two constituents together in an electron bombardment furnace (EBM). To produce specimens free from segregation a molten zone was passed over the length of each rod six times in alternate directions at a speed of 10 in. per hr. Typical specimens were analyzed for interstitial impurities by gas analysis and for metallic impurities by spectrographic analysis. The results of this analysis are shown in Table I. Many of the tensile specimens were also analyzed (after testing) by scanning the gage length in an electron beam microanalyzer, from which it was found possible to predict the approximate composition of a specimen from the original proportions of each element in the EBM. The tensile specimens were made with a gage length of 0.5 in. and diameter of 0.075 in., using a Servomet Spark machine. By careful machining on the finest range for the final i hr of this technique, surface cracks could be reduced to the level where they were easily removed by electropolishing in a solution of nitric and hydrofluoric acids. The specimens were strained at a rate of 10 4 sec-' using friction grips designed to prevent accidental straining and maintain a good alignment before straining. The orientations of the individual specimens tested are shown in Fig. 1 and the corresponding compositions listed in Table I1 together with collated experimental data. 2)RESULTS a) General Deformation Behavior. The effect of composition on the room-temperature deformation curves of similarly oriented specimens is shown in Fig. 2. The yield stresses of the pure constituents, while not the lowest reported to date, were at least comparable with existing data. Although the solution hardening was large for alloys at either end of the phase diagram, and comparable with the Ta-W solution-hardening data of Ferris et a1.,8 the low work-hardening rate characteristic of niobium was sustained until a composition of Nb-85 pct MO had been reached. Associated with the peak yield stress ob-

Jan 1, 1969

By L. Cichowicz, K. K. Millheim

The constant-rate drawdown test performance for a low-permeability, verticany fractured gas well was investigated. A series of gar wells were tested by flowing each well at constant rate until the data could be analyzed using con-ventional radial flow theory. Each well was then shut in to build up. After a sufficient buildup was obtained, another flow Iest commenced but at a higher flow rate than Ihe first test. Again, the well was shut in when radial fiow was obtained. his procedure was repeated for three to four different flow rates. Two wells in the San Juan basin were tested using this procedure. Both wellere fractured after completion, cleaned up and then shut in until flow testing commenced. Test designs of both wells permitted investigation of the most realistic values of egective permeability, wellbore radius and turbulence factor. Also, being able to determine the eflective fracture flow area and vertical fraclure efficiency was inherent with this testing approach. It was observed that fractures in both wells influenced the Pressure behavior for approximately Is to 40 hours (depending on the flow rate) before radial flow was evident. After this time, drawdown data were analyzed using radial pow theory. When a low-permeability gas well has vertitally oriented, induced fractures, the early flow geometry ic. essentially linear. It will be shown how to determine when a flow test has been conducted long enough so lha' the most representative values of effective permeahiiity. wellbore radius and turbulence factw can be calculated. From the linear pressure data, valuable information about The fracture treatment, such as the effective flow area and vertical fracture efficiency, can be determined for vertically froctured wells. Introduction During tests on gas wells in the Sari Juan basin7 initial transient behavior lasted for many days because of the low permeability of some porous media. As a result, stabilized flow performance could not be obtained. If these wells received some type of stimulation treatment, early pressure behavior deviated from conventional theoretical radial Row. When conventional radial flow theory was used to analyze these low-permeability fractured gas wells, larger values of flow capacity and absolute open flow potentials (AOF) sometimes resulted. Wells were assigned open flow poten- tials that proved to be 3 to 10 times higher than the well would sustain over a longer period of production. In some cases where the wells had flowed for longer periods of time during a constant-rate drawdown test, it was noticed that the effective flow capacity appeared to be decreasing with time until a certain value was reached. The early nonradial pressure behavior can be explained If linear flow is assumed. Rusell and Truitt mathematic. ally investigated the vertically fractured well in a bounded area. They showed that early flow behavior was essentially linear and, for x,/x. approximately less than 0.10 radial flow was obtained after short periods of time. Then realistic values of effective permeability and skin could be determined. Scotta experimentaliy studied the vertically fractured well with a heat flow analog. He showed that earb flow was linear, Both studies indicate that, for small values of x,/x,, linear flow approaches radial flow if the well is tested long enough, To help prove this concept of early linear flow caused by induced vertical fractures, two low-permeability gas wells were tested. Both wells received large fracture treatments prior to testing. A vertical fracture was indicated from the analysis of fracture treatments, As anticipated, tests of both wells indicated early linear flow that was later followed by a period of radial flow, Data collected from each well were analyzed. From the well tests, plus other information on each well, the effective permeability, wellbore radius and turbulence factor were calculated. Effective fracture flow areas calculated from test analyses for each well proved to be approximately one-fourth the created area calculated from classic hydraulic fracturing theory: other fractured wells that were tested but not presented in this paper also indicated that the effective fracture flow area was one-fourth to one-third the created area predicted from hydraulic fracturing theory. The vertical fracturing efficiency was estimated from the calculated values of effective wellbore radius and fracture flow area. For the two wells tested, calculated fracture lengths x, were 112 and 105 ft, and the vertical fracturing efficiencies E, were 122 and 183 percent. Development of Flow Model Agnew' showed that most induced fractures below 1,500 ft are vertical. Anderson and Stah15 indicated that most of the fractures they studied were vertical. Thc model proposed for early flow in most vertically fractured gas wells is shown by Fig. 1. This model should approximate early flow behavior until radial flow is reached, at which time a radial model with an effective wellbore radius of 0.5 they will

Jan 1, 1969

By D. L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry. It presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a US Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) uses the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package uses a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgment scheme that provides an effective method of identifying problem areas that may exist in the mine network. The package was written in Fortran for a 64-kilobyte, Z80-based microprocessor computer.

Jan 1, 1986

By Evert Hoek

Summarising a conference is never an easy task, but I will try to keep my comments brief and to the point. There are a number of lessons which we have learned from our deliberations together during these past three days, and I will try to give you my impressions of these lessons and of their practical implications in open pit mining. The first thing that has become increasingly obvious during these discussions is that it is no longer acceptable to offer an 'Act of God' as an excuse for a major slope or tailings dam failure. Disasters such as that at Aberfan in the United Kingdom have focussed the world's attention on the activities of the mining industry and the report of the commission set up to investigate the Aberfan disaster clearly showed that adequate knowledge was available and that failure to apply this knowledge did not qualify as an 'Act of God'. The courts and the world's press are certain to impose increasingly harsher penalties and criticism on those held responsible for major failures, particularly of tailings dams, in the future. One of the major problems in applying available knowledge to slope problems is that attempts to apply this knowledge are frequently left too late. To provide an engineering solution in the case of a slope in an advanced state of failure is an almost impossible task, and it is essential that those responsible for the stability of a slope must learn to recognise signs of distress at an early enough stage for effective remedial measures to be taken. As our ability to solve slope problems improves, the time at which slope stability problems are considered in a mining project must move forward to a stage at which these problems can be anticipated and dealt with before they arise. Conferences such as this are important in that they enable us to exchange ideas and advance our knowledge to a level at which such predictive engineering will be possible. It has been encouraging to hear of mining projects such as the Bougainville Copper operation where slope stability studies were carried out as part of the overall evaluation programme and it is hoped that this will become a more common procedure in the future. Providing a safe slope in an opencast mine obviously costs money, either in terms of the reduced ore to waste ratio given by flat slopes or because of the cost of stabilization techniques such as drainage or the use of rock anchors. An optimum slope design will provide maximum safety at minimum cost but achieving this optimum is not an easy task. Any one of us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make

Jan 1, 1971

By A. M. Gaudin, D. W. Fuerstenau

IN concentration of certain ores by soap flotation, prevention of quartz flotation is desired; the contrary is true in treatment of some oxide iron ores. Experimental study of the flotation of quartz goes back at least a quarter of a century.' Clean quartz does not float with fatty acids or soaps but does float when activated by one of many metallic salts. Control of pH is important. Broadly speaking the problem of quartz flotation has been approached from the empirical side, as was the related topic of flocculation or dispersion of quartz suspensions? Empirical studies indicated the existence of critical relationships between the additions of collector and activator. These additions were not stoichiometric for the formation of soaps of the activator cation. For example, Gaudin and Rizo-Patrona found optimum quartz flotation at pH 10.6 using barium activation and oleate collection when the molar ratio of oleate to barium was 1 to 1 instead of 2 to 1, as would be called for formation of Ba(OL),. Cooke and Digre" ' found that if calcium is the activator, a minimum quantity of that agent is required for effective flotation when the pH is 11.5. In other words, if the concentration of Na' exceeds 10 -2.5 mols per liter or if the concentration of H exceeds 10-11 mols per liter, the concentration of Ca++ in solution required for quartz activation is increased. This suggests that H+ is much more effective than Na+ on 10-2.5 quartz, perhaps in the ratio ofp or 108. Schuh- mann and Prakash6 studied anew the activation of quartz by barium, calcium, aluminum, and ferric iron. Salts of these metals are activators provided they are in stoichiometric excess over the collector used with them. Alkaline-earth salts are effective only in alkaline circuits. Important as they are in giving data on the effect of various agents on quartz, all these studies fail to give information on the detailed structure of the quartz-solution interface. A beginning in this direction was made by Gaudin and Chang,? who measured the adsorption of radioactively marked barium and laurate ions at quartz surfaces, and by Gaudin. Spedden, and Laxen,8 ho measured the adsorption of radioactively marked sodium at quartz surfaces. Work has also been done by Bell0 n measurement of the adsorption of sodium ion and chloride ion at quartz-solution interfaces. In all these experimental measurements of adsorption, the solid was centrifuged or filtered from the bulk of the liquor with which it had been associated; and the composition of the solid surface was ascertained by analysis, after allowance was made for the ionic composition of the liquor included with the centrifuged solids on the assumption that it is identical to the bulk liquid. Adsorption measurements give only the total amount of collector adsorbed at the quartz-solution interface; they give no indication of the distribution of these adsorbed ions at the interfacial layer. It is the ionic structure of the solid-solution interface and its importance to flotation that is the subject of this paper. The structure of this interfacial layer can be investigated by means of electrokinetic methods so that by combining electrokinetic studies with adsorption measurements, a more complete picture of the quartz surface may be obtained. The following studies were made to ascertain how electrolytes used in the soap flotation

Jan 1, 1956