Search Documents

By Samuel H. Dolbear

THE purpose of a technical report is to record facts, usually collected by investigation, and to interpret these facts in understandable language. The audience may range from a small shareholder without technical knowledge, to a highly trained engineer or geologist. If the client is a mining company with technically trained executives, the report writer's problem is relatively simple. The writer will then be appraised not only for his conclusions, but for clarity of language and organization of the report. If the writing is bad, the construction careless, and there is a failure to clearly convey to the reader the facts and the author's conclusions, the report is a failure and the writer may have damaged his professional character. Spoken words die quickly, written words may constitute a permanent record and if they are badly composed they may rise up to damn the author. "A good measure of an author's understanding of his subject is his ability to express it clearly in plain words." Good English Teachers in the fields of mineral technology have frequently complained that even in post-graduate groups there is an appalling indifference to their appeals for good English. Some have even noted a student's belief that the use of refined English is effeminate. If those with such immature beliefs could measure the pay-check damage arising from the use of "sloppy" language, they would realize that precision and refinement in English may be quite as important as technical accuracy. When the reader audience is without technical knowledge simplicity in treatment becomes especially important. If one is engaged in consulting work, in government service, or in any field where reports have public distribution, the language employed should be technically adequate but simple enough to be understood by non-technical readers. For example, one may use the term "visual" in place of "megascopic." Technical language can be so obscure that it cannot be understood even by highly-trained students. In the March-April (Vol. 47-No. 2) issue of Economic Geology, Nicholas Vanserg ridicules these extremes and quotes various paragraphs from published material, such for example: "However, lattice orientation unaccompanied by cognate dimensional orientation can never be attributable to growth from an isotropic blastetrix." "The temperature declines because of cessation of the exothermic chemical and mechanical equilibriopetal processes." These he calls "good geologese" and they are calculated not only to baffle the reader but to impress upon him the erudite character of the author. Revision In some cases, difficulty arises from the fact that the writer is too close to the subject and unconsciously assumes that his reader is equally familiar with the background of the report. It is difficult for the writer to regard his work objectively and to determine to what extent it is likely to be understood. Every important manuscript will gain in clarity if the author will have it reviewed by an informed reader. But the writer must not be oversensitive to criticism and should not treat his composition as perfect and beyond the possibility of improvement. The first draft of a report always requires revision, regardless of the care used or the ability of the writer. Three or four revisions are not uncommon. The first draft usually requires expansion in places, the deletion of non-essential material, and language changes to promote clarity of expression. This should be done by the author after a lapse of time, even if only overnight, in which his mind has been occupied on some other subject. Possible improvements are always more visible. The manuscript should be passed on to another reader for further suggestions. Organization of Material The engineer should study available reports and library references before going into the field. If the previous reports have been responsibly done and can be accepted as correct, then much field time can be saved. It is, of course, customary to make some on-the-ground checks to confirm earlier reports, particularly those relating to ore reserve which may have undergone changes. Report writing requires time and expense, but nevertheless, the basic reasons for conclusions should be presented even in the case of a worthless property, for it may prevent a duplication of the work. If the mine examined is obviously of no further interest, no useful purpose can be, served by preparing a report in detail. In one case an engineer travelled all the way to South America only to find that the mine had been grossly misrepresented and was valueless. His cabled report "Nonsense" is a case of over-simplification, but it served his company's purpose. The first step in report organization should be the selection of subjects. This should be done at the mine, and the data collected for each subject should be reviewed in considerable detail on the ground. Otherwise one may find that he has failed to collect some essential details not readily obtained after he has returned to headquarters. If the property to be described is undeveloped, then many of the subject titles are automatically eliminated. Usually no useful purpose is served by an attempt to calculate the cost of production under such circumstances, although the cost of exploration

Jan 1, 1952

By J. Szekely, Robert G. Lee

Calculations are presented for the prediction of the combined radiative-convective heat loss from molten steel held in a ladle, covered by initially molten slag. A mathematical formulation is given and numerical solutions are presented of the resultant partial differential equation. It is shown that a slag layer of about 2 to 3 in. thick would prevent any significant heat loss from the top metal surface for Periods of up to 1 hr. For thinner slag layers (or in the absence of the protective slag) appreciable heat losses would occur; plots given in the paper allow the quantitative evaluation of the fall in the metal temperature due to this heat loss. The ironmaking-steel processing operation involves several intermediate steps where the molten metal is held or transfered in ladles. The quantitative assessment of the heat losses occurring under these conditions is of considerable importance in process design considerations since the temperature of the metal may have to meet rigid specifications in any given part of the processing sequence. While the metal is held in a ladle, heat is lost by two mechanisms: i) by conduction into the ladle walls; ii) by radiation and convection from the top surface. Calculations relating to the conductive heat loss, are readily made and information may be found in the literature both on data pertaining to metallurgical situations and on the techniques that are available for performing additional computations.'-3 The evaluation of the combined convective-radiative heat loss is less straightforward, especially when there exists a protective slag layer covering the metal. In this latter case, as the top slag surface loses heat partial solidification may occur and the latent heat thus given up by the slag may represent an effective barrier to the heat loss from the metal. A semiquantitative assessment of the role played by the slag in preventing heat loss from the metal has been made in a previous paper,4 where it was shown that a slag layer 6 in. thick would act as a near-perfect insulator for periods of up to 2 hr. However, this first paper reported on an essentially preliminary investigation that considered only one slag layer thickness; furthermore, the boundary conditions used for the calculations were somewhat restrictive since no allowance was made for changes in the metal temperature. The purpose of this second paper is to extend the scope of the preliminary investigation previously reported by: i) considering several slag layer thicknesses; ii) allowing for variations in the metal temperature; and finally iii) by performing calculations on the net loss from the metal rather than from the slag surface. FORMULATION Consider a slag phase extending from y = 0 to y = L1, covering a metal phase that occupies the region extending from y = Ll to y = L, as illustrated in Fig. 1. Denote the slag and metal temperatures by TS and Tm and assume that initially both slag and metal are molten, having a uniform temperature Ti. At time = zero the surface represented by the y = 0 plane (top slag surface) is brought into contact with cold air, the temperature of which is given as T Thus for time > zero, heat will be transfered from the slag to the air by natural convection and thermal radiation; as a result of this heat loss the slag temperature will fall and after some time a solid phase is formed and a solidification boundary (more realistically described as a zone) will move progressively from y = 0 toward y = L1. Once the region of temperature gradients, moving ahead of the solidification zone, reach the slag-metal interface (y = L1) there will be a net transfer of heat from the metal through the slag to the cold air, across the y = 0 plane. In the formulation of moving boundary problems, involving phase changes that require computer solution, it is convenient to represent both phases by a single equation, making allowance for the latent heat of solidification by assigning an appropriate temperature dependence to the specific heat content. Thus the energy equation for the whole of the slag may be written as follows:

Jan 1, 1969

By C. S. Matthews, M. J. F. Rosenbaum

The purpose of thir work wax to lcarn it~lzut infori~lation could he obtained from various typs of pilot water floods and to attempt to find the optunum pilot patter11, for a revervoir which had previously been depleted by a solution gas drive. The study was made in the laboratory with mathemetical methods a dynamic analog and a potentiotnetric analog. Results werp tested against the field llistorics of a nrrnlber of pilot water floods. At a reasonable valrre of currzulative injection, the total production rate for the one-injector five-spot should reach about 6.5 per cent of injection rate, and for a four-injector five-spot, about 9 per cent. Accurate estimates of ultimate recovery cannot be made on the basis of such snzall prorluction rates. However, with a pilot composed of nine ir1jector.s and 16 producers the production rate is approximately 50 pcr cent of injection rate at a reasonable value of camulative injection. Sonle inforn~ation for extended performance predictions might he obtained from such a large pilot. These conclusions were drawn on the basis of results obtained for unit mobility ratio, and a sturly using tlre potentiometric analog was made of the effect of other mobility ratios to determine the range of applicability of these predictions. For the four-injector, five-spot pilot with the ratio of production to injection rate (before water breakthrough) is about twice that for with it is about two-thirds; and with M0= 10, it is about one-third For high mobility ratios, it was found that the production rate increased considerably as water-cut increased. These result can be used to modify, qualitatively, the inter.pretntions based on curves for the unit rnobilit\. ratio CaSeS. It was found that the maximum ratio of production rate to injection rate obseriled in field pilot floods was of rhe scime order as that prerdicted by these methods. The time required to reach thisr maximum did not generally agree with the time predicted for a homogeti~orir reservoir. The differcrlce between predicted and observed time of response gives an indication of the permeability profile and of the condition of the producin,g wells. Pilot water floods of the pattern type are generally carried out in reservoirs which have been depleted by solution gas drive and are at low pressure. Under these conditions, oil and water can be considered incompressible. It is assumed that, as the water is injected, an oil bank forms ahead of it and that there is a distinct interface between the water zone (or bank) and the oil zone (or bank) and between the oil zone and the region ahead of the oil zone. It is further assumed that only gas is mobile in the unflooded (gas) region, only oil is mobile in the oil bank and only water is mobile in the water bank. The saturations and the mobilities associated with each zone are assumed uniform. We idealize our reservoir to be homogeneous, horizontal and of constant thickness. Effects of gravity within the producing layer are assumed negligible. If the actual time-dcpendent flow problem is approximated by a acries of steady-state problems. the potential and stream function in the oil bank and water hank satisfy Laplace&apos;s equation in two dimensions. We can therefore use a poteiitiometric analog of this system. Potentiometric models have yielded uscful results in this laboratory&apos; and clsewhere in the study of a variety of secondary recovery problems. For the case where M = I, we generally prefer to use theoretical mcthods as well as a simpler dynamic analog. Except where otherwise noted, the ratio, side of five-spot/wellbore radius. is taken to be 3,600. a figure which corrcsponds to a normal-size wellbore in a 10-acre well spacing. THEORETICAL EVALUATION OF VARIOUS PILOT PATTERNS, Mw0 = 1 <&apos;he theoretical models which we used to examine the performance of various pilots are shown in Fig. 1. Image theory was used to determine the ratio of production rate to injection rate as a function of the volumc of the flood. The ratio of production rate to injection rate was chosen because this is an easily measurable quantity which is characteristic of a pilot

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation&apos; of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,&apos;-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals&apos; force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.&apos; The streaming potential

Jan 1, 1970

By R. J. Burgess, A. R. Ramey, A. R. Adams

During interpretation of pressure buildup tests on gas wells in a tight dolomite gas reservoir, peculiar behavior was noticed. Two straight lines were apparent. Effective permeability to gas taken from either straight line was about the same, and the Miller-Dyes-Hutchinson dimensionless time check for the straight line was proper for both straight lines. Geological data indicated the likelihood of scattered trending fractures in the reservoirs. Since the first straight Iine yielded permeability values close to the geometric mean permeability from core analyses, it was postulated that the reservoir model was that of an acidized well completed in the tight dolomite, but that widely scattered hairline fractures caused the mean permeability of the reservoir distant from the well to be higher than the matrix permeability. Because all other studies of fractured reservoirs to the authors&apos; knowledge assumed that the fracture matrix was dense enough to communicate directly with the well, no interpretative methods were available. The Hurst line-source solution for a radial change in permeability for interference between oil reservoirs was adapted to pressure buildup testing. The result indicated that the first straight line should yield the proper matrix permeability and wellbore skin effect. The second straight line may be extrapolated to obtain static pressure. The time of bend between the straight lines was used to estimate distance to a fracture. Application to field test data is shown. It is believed that the methods developed and the case history presented will add to present tools available for pressure buildup interpretation. Introduction Since the pioneer studies by Miller, Dyes, and Hutchin-son1 and Horner&apos; in 1950 and 1951, well test analysis has become recognized as one of the most powerful tools available to both production and reservoir engineers. Well test analysis serves as a logical basis for well stimulation and completion analysis, and for long-term reservoir engineering. Since the early 19501s, much effort has been placed on the development of well-test analytical methods. Reservoir and well conditions of increasing complexity have been considered systematically to provide the analyst with a catalog of causes and effects. Matthews and Russella state that some 200 papers dealing with this subject have been published in the last 35 years. Developments in well test analysis appear to have originated in one of two ways. Either a physically realistic field condition was anticipated and analytical solutions for the condition achieved, or anomalous field test behavior was recognized and interpretative methods sought for the anomaly. In recent years, it has appeared that the latter has inspired an increasing number of studies. The analyst today finds an increasing number of known cause and effect studies available for well test analysis, the classic of which is that of finding the specific flow problem that generated the answer — the well behavior. Although it may be impossible to achieve this goal uniquely, the analyst often is able to select a useful interpretation that combines all known performance and geologic data — or to show that various logical alternatives would not significantly affect the interpretation. During a recent reservoir study, we observed gas well test behavior that did not appear to fit behavior described previously. Although it cannot be said that we have found a unique interpretation, we shall present in this paper the peculiar behavior observed, and describe the reservoir and interpretative methods developed. Reservoir Description The subject gas reservoir is a 9-mile-long, narrow dolomite reservoir lying within a limestone of Ordovician age. (See Fig. 1.) The dolomitized rock in the field consists of dark brown to buff, dense to coarsely crystalline, vugular dolomite containing numerous hairline fractures, many of which may have been closed in the reservoir and parted when cores were brought to the surface. Larger fractures are also apparent in core, but usually are filled and sealed with euhedral dolomite crystals. Portions of the north flank of the reservoir are known to be cut by a sealing fault downthrown to the north. Gas wells located near the fault have higher open flow potentials than those more distant from the fault. This is believed to be a result of higher permeability near the fault due to more extensive and open fractures. Detailed coring and core analysis have been performed on several of the wells in this reservoir. Fig. 2 presents permeability variation&apos; plots for both horizontal and vertical

Jan 1, 1969

Map

Jan 1, 1960

By AIME AIME

FIFTY years ago William Bertolette Plank was born in Pennsylvania, in which state he was also educated, winding up with an E.M. from Penn State in 1909, at the age of 23. &apos; He remained there as instructor for a year, and then went with the Philadelphia & Reading Coal & Iron Co. as mining engineer for three years. During the next four years he was on the staff of the Pittsburgh Coal Co. In 1916 he turned to Government work, going to Pittsburgh as junior mining engineer for the U. S. Bureau of Mines. He became successively assistant mining engineer there, mining engineer at the Bureau&apos;s Urbana, Ill., station, and finally Mr. Plank was appointed district mining engineer for the Bureau at Birmingham, Alabama.

Jan 1, 1937

A SELF-RESPECTING miner doesn&apos;t wash the cuttin&apos;s off his hard hat until he quits his job but, on the other hand, he keeps his lamp clean and a "spot" focus on the work at hand; the former habit is a matter of pride and the latter serves for efficient operation. During 1949, the mining engineer got all the "wet raises" for the problem of cutting costs to meet the drop of metal prices and keeping research work up to schedule when strikes tied up his work were his headaches. We note, not without admiration, that he hasn&apos;t washed the muck off his hat in token of surrender but, on the contrary, his light shines bright on the job to be done as can be seen in the following pages. Few people have any conception of how much ore and rock have to be mined and how much sorting it takes to cull a pound of copper from a 1 % ore body. These people would be even more startled to picture the problems faced by the engineer in mining and extracting, profitably, .2 oz of gold from a ton of ore as is done at some of our lode mines. Strikers have sometimes kept our researchers from their pilot plants and research laboratories, but the end of the year shows progress in making ore out of taconite and ferruginous sandstone, with a pilot plant in operation at Aurora, Minn., and plans for one near Birmingham. Unfortunately, it looks as though the mining engineer will have to make John Doe secure in mineral resources in spite of himself. Coal for steel, power, and to warm our homes is still economically possible, in spite of Mr. Lewis, through development of mechanized tools for mining. During the year, the use of continuous mining machines has extended, transport systems are being adopted to keep the ore flowing from the face to the tune of 40 tons per man-shift. Experiments in the gasification of coal are going forward in several places and may eventually extend our fuel reserves by the addition of coal seams now too lean for mining. Liquid fuel from coal, oil shale, or natural gas will become economic when oil consumption exceeds our supply; but, at less than 30 cents a ton direct cost for mining oil shale, the engineer is almost making it competitive under present market conditions. In this age of specialists, the mining engineer is still holding his own as a broad-gauge man. As a matter of fact, he is emerging from a stage of semispecialization as a coal, nonmetallics, or metal mining man to the realization that, with mechanization, mining is fundamentally materials handling whether it is fluorspar, coal, or copper ore. From the coal business come rubber-tired mechanical loaders to the iron mines of Birmingham. Shuttle cars are also finding application in the lead mines of the Tri-State. Open-pit methods are universal. Belt conveyors, trucks, Diesels, and mobile, jumbomounted drills are finding application in all types of mining. In preparation, such methods as flotation,- heavy density, electrical, and centrifugal are finding application in coal, nonmetallics, and metals. These concepts have been recognized by the mining engineer who has kept himself informed and has been quick to seize a method, machine, or a process from another operation and, with ingenuity, applied it to his problems. This, our Annual Review issue, is written by mining engineers. In gathering these separate articles under one cover for publication, we think of it as a trrbute to the tireless energy and skill of these men. They get little of the publicity accorded physicists, medical men, labor leaders, or company executives, but they supply raw materials without which industry would die.

Jan 1, 1950

By W. Crafts, J. L. Lamont

Electrolytic extraction of carbides from quenched and tempered steel and their examination under the electron microscope were found to be helpful in understanding the mechanism of secondary hardening in alloy steels1 and the same technique has been applied to isothermally transformed steels. A preliminary survey of the utility of the method has indicated that it has promising possibilities for investigating the characteristics of pearlite and bainite. The examination of a few carbon and chromium steels has suggested that pearlite is formed with carbides of two varieties representing the lamellar and nonlamellar forms and that bainite appears to form with a structure analogous to, but significantly different from, martensite. Procedure The method used for examining the carbides was similar to that described previously.1 The chromium steels used in the investigation were made from an Armco iron base in an induction furnace and were not treated with grain-refining deoxidizers. The composition of the steels is given in Table 1. Three-inch square ingots were forged and rolled to 1/8-in. thick sheet for use in the isothermal studies. After rolling, the sheets were sandblasted to remove the rolling scale. Specimens approximately 3/4-in. wide and l1/2-in. long were prepared from the 1/8-in. sheet. They were heated in a salt "bath at 2100°F (1150°C) for 1/2 hour, transferred to other salt baths at 1300°F (704°C), 1000°F (538°C), 800°F (426°C), or 600°F (315°C), held for various periods up to 100 hr and finally quenched in water. After quenching, the specimens were cut in half, one half being submitted to microscopic examination and the other half being used for the electrolytic extraction. The isothermally transformed specimens were submitted to examination under the light microscope to determine the degree of transformation and type of structure and were photographed at 2000 X. Carbide residues were obtained by electrolyzing in 10 pet hydrochloric acid and collecting the residue in glycerine to minimize attack by the acid. As pointed out in the earlier paper, the carbides are attacked to some degree during electrolysis. This attack is relatively minor on the coarser carbides but may be quite severe on the fine bainitic carbides. The residues were washed free of the glycerine with water and alcohol. The alcohol was removed by repeated washings of amyl acetate, and the amyl acetate suspensions were transferred to stoppered vials. Debye-Sherrer X ray diffraction patterns of the residues were prepared using a chromium target. A selection based on the microstructure and X ray data was then made of samples considered most illustrative of the progress of transformation. Electrolytically extracted residues from these samples were submitted to examination by W. D. Forgeng and A. C. Jenkins on the electron microscope at the Research Laboratories of The Linde Air Products Co. and electron micrographs were made at X 5000 and enlarged to 25,000 X. The micrographs obtained with both the light and the electron microscopes are mounted side by side in the accompanying figures. Although no effort was made to establish the T-T-T diagram for the chromium steels, the times for holding in the salt bath were adjusted with the intention of making the samples represent different stages in the transformation at temperatures of 600, 800, 1000, and 1300°F. The degrees of transformation and results of X ray examination are shown in Tables 2—4. The carbide designations refer to orthorhombic or trigonal carbide types and are not meant to imply that the compositions are exactly as indicated. X ray Diffraction Data The occurrence of Fe3C and Cr7C3 in these steels was found to be consistent with published data on comparable chromium steels. Steels A and B with relatively low ratios of carbon to chromium contained Cr7C3 in the pearlitic structures and FeuC in the

Jan 1, 1950

By R. F. Mitchell, G. F. Dillon, A. F. Armington

In this paper the present methods of boron preparation are discussed with emphasis on the iodide intermediate. Several methods of boron triiodide preparation were investigated, the most satisfactory method being the preparation from the elements. A yield of 60 pct based on iodine is found for this method. Zone-refining, sublinzation, distillation, and fractional-recrystallization results are given for the boron triiodide, with distillation producing the best results. Several methods of decomposition are also discussed. The purity of the resulting iodide boron approximates the puritjl of the best available bromide boron, ELEMENTAL boron has been suggested as a possible high-temperature semiconductor by several workers,&apos; but has never been exploited as a device material. The principal difficulty with boron is the unavailability of pure crystalline material from which accurate information on electrical properties could be obtained. Most boron crystals presently produced are very imperfect in structure and of questionable purity, particularly in relation to carbon content. Several methods of boron purification have been reported in the past few years, all of which produce material with a purity better than 99.0 pct. Most of these methods have been the subject of a recent review by Starks&apos; and will not be elaborated upon in this report. However, of all the purification methods reported, only those using halide intermediates produce a purity approaching that usually required for electronic applications. The bromide intermediate has been most used for the preparation of high-purity boron.&apos;y3 This material is easily prepared from the elements and can be effectively purified by distillation and decomposed by hydrogen reduction. The resulting product contains a trace of silicon, and an uncertain amount of carbon, believed to be approximately 100 ppm. It has been recently reported by Russian workers that high-purity boron can be produced using an iodide intermediate.&apos; In the work cited, boron is reported free of spectro-scopically determined impurities, but the reported detection limits are quite high (- 100 ppm). In addition, no data is given on the carbon content of the product. In the present paper, boron triiodide was chosen as the intermediate for several reasons. First, carbon tetraiodide, which could be a major impurity, is reported to be unstable above 200" and hence could be easily separated from the boron triiodide by its decomposition, since temperatures greater than this are attained during the purification process. The low melting point (45°C) and boiling point (20B°C) and the relatively high vapor pressure of boron triiodide should allow the application of any physical purification technique to the material. The possibility of a lower decomposition temperature than that used for the bromide process is another advantage which might cut down extraneous contamination. The iodide, however, does have certain disadvantages when compared with the bromide, the production cost being the most significant. This is the result of a higher halide-to-boron weight ratio, which means more intermediate must be employed. The cost of the starting material is also greater for the iodide. This cost could be considerably reduced however, by recycling the iodine byproduct. Epitaxial growth of boron, which is probably the best method of producing junctions, should be possible with either the bromide or the iodide as the intermediate. However, this has been attempted only on a limited scale up to the present time because of the unavailability of good crystals. The authors have been relatively successful in laying down a heterotaxy of boron on silicon, however. This will be reported at a later date. Several crystalline modifications have been reported for boron, four of which are now believed to be real.&apos; These are the a! and 0 rhombohedral and the a, and 0 tetragonal. In general, the a! rhombohedral is the low-temperature form and the B rhombohedral is the high-temperature form. The tetragonal structures are detected between 1000"

Jan 1, 1964

By D. C. Hilty, W. Crafts

A qualitative pseudoternary solidification diagram for the Fe-S-O system modified by manganese is proposed and supported by experimental derivation of an isothermal section at 1475°C and substantially 1 pct Mn in the solid-metal phase. The solubility of oxygen in liquid iron containing 1 pct Mn and sulphur contents up to 0.9 pct has been measured at 1600°C and found to increase as the sulphur content exceeds 0.15 pct. AS has been pointed out previously,&apos; all oxide and sulphide inclusions in steel, excluding mechanically entrained matter, result from modifications of the basic Fe-S-O system. Therefore, one method of attack on the problem of the mechanism of deoxida-tion and inclusion formation is to examine the influence of deoxidizers on the Fe-S-O liquidus diagram. This approach has been adopted in work on the subject being carried out at the Metals Research Laboratories of the Electro Metallurgical Co. and has resulted in the postulation of types of solidification diagrams for the Fe-S-O system modified with common deoxidizers. This method has been of considerable assistance in interpretation of the factors affecting the formation of inclusions.&apos; For the most part, however, these diagrams have been highly speculative. They were constructed primarily by inference from the pertinent binary and ternary systems and from the appearance of inclusions produced by specific deoxidizers. Moreover, since the systems contain four or more components, simplifying assumptions and qualifications were necessary in order to permit their representation as modifications of the Fe-S-O diagram. Consequently, experimental confirmation of the type of construction employed for these diagrams is desirable, and the present paper is concerned with such evidence. The addition of manganese to the Fe-S-O system was selected for initial investigation. Manganese is an important component of practically all steel and is, therefore, of fundamental interest. Because of its great affinity for sulphur, manganese has a more profound effect on the sulphide side of the Fe-S-O diagram than any of the other common deoxidizing eletments. In addition, more quantitative information pertaining to the contiguous binary and ternary systems involving iron, manganese, sulphur, and oxygen is available than for the other deoxidizers. Fe(Mn)-S-O Solidification Diagram Many of the side diagrams of interest in connection with this system are known. The Fe-Mn binary has been well established by several investigators;% the Fe-O system has been clarified by Darken and Gurry;&apos; and FeO-MnO diagrams have been published by Herty,5 Andrew, Maddocks, and Howat,6 and by Hay, Howat, and White.7 The Mn-O diagram does not appear to have been derived experimentally, but the portion of &apos;it that is of interest can be visualized easily from a consideration of the melting points of Mn and MnO and the fact that a broad miscibility gap must exist between them. The ternary Fe-Mn-O diagram has been discussed by Benedicks and Löfquist,8 Wentrup,9 and by Körber and Oelsen.10 Experimental study of the Fe-Mn-O system has been carried out by Körber and Oelsen and to a lesser degree by Chipman, Gero, and Winkler,11 Hilty and Crafts," and others. On the basis of published information, then, an outline of the Fe-Mn-O liquidus diagram can be constructed as illustrated by Fig. 1. In this, as in all succeeding diagrams, transformations such as the ?-? reaction in iron have been ignored for purposes of simplification. The arrows denote falling temperature. The distinguishing feature of this diagram is the broad region of liquid immiscibility extending

Jan 1, 1955

By F. W. Jessen, N. Mungan

The plastic flow characteristics of clay water suspensions were first recognized by Binghaml in 1916 and further studied by Ambrose and Loomis&apos; in 1931-1932. Many physical and chemical properties of clay suspensions are deeply influenced by particle size distribution as well as by the exchange cation. Separation of a number of fractions is particularly helpful in making a detailed study of a suspension. A limited amount of work has been conducted on the effects of particle size on specific properties of mud drilling fluids. A knowledge of particle size distribution is essential for a better understanding of fundamental properties of clay suspensions, particularly viscosity and gel strength. The purpose of this investigation was to study the effect of particle size on the viscosity and gel properties of clay suspensions and to determine any changes in mineral composition accompanying variation in size. EXPERIMENTAL PROCEDURE Numerous methods may be used to fractionate a poly-dispersed clay suspension into nearly mono-dispersed systems. Particles larger than 44 micron (325-mesh) may be obtained by wet screening. For sizes from 44 to 1 micron, the fractionation may be accomplished by sedimentation, elutriation plus microscopy,&apos; or turbidimetry.6 When dealing with systems which contain a major portion of particles below l-mi-cron size, slit ultramicroscopy,7 centrifuge methods of Svedberg,5 eams,9 and McBain,l0 and X-ray methods" may be employed. The Sharples super centrifuge has been proved suitable for the economical separation of suspended particles of submicron range.12,13,14 Three-hundred and forty-five gal of 1 per cent by weight Aquagel suspension was mixed in a high-speed 5-gallon mud mixer and the suspension was allowed to stand in 5-gal glass bottles for 30 days to assure full hydration. All particles larger than 44 microns were removed by wet screening. Five fractions in the range of 44 to 1 micron were obtained by sedimentation. The Sharples super centrifuge method described by Hauser and Reed.13 Norton and Speil,14 Ha user and Lynn,15 and Hauser and Schachman,10 as employed to yield five fractions of submicron size. A super centrifuge operation chart prepared by Fancher, Oliphant, and Houssierre12 was used to determine operating conditions for the desired particle ranges. The clay suspension, after removal of all material above 1-micron size, was centrifuged. During rotation of the bowl, the particles were deposited on a thin plastic liner which fit closely inside the bowl. After passing 5 gal of suspension through the centrifuge, the liner was removed and the particles on the liner were scraped off, remixed and recentrifuged. This was repeated five times. Thus, Fractions H, I, K, and L were obtained. The finest fraction, M, remained in an approximately 0.4 per cent suspension. Water was evaporated under reduced pressure from this suspension to yield the finest particles. Results of the fractionation are included in Table 1. In order to achieve proper orientation and humidity conditions for X-ray diffraction analysis, the following procedure was employed. The dilute suspensions were placed on glass slides and allowed to dry at room temperature. This was repeated several times. Previous to measurement each sample first was placed in a water desiccator for half an hour and then allowed to stand for 15 minutes at room temperature. thus yielding an equilibrium condition of about 52 per cent relative humidity. The relative humidity of the room in which the X-ray diffraction was carried out was maintained at approximately 50 per cent so that there was no change in the spacings during the X-ray examination. Samples

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,&apos; and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.&apos; Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8&apos;7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8&apos;9 Copper minerals sometimes yield elemental sulfurlo&apos;" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,&apos;5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to bene-ficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation. Earliest surveys of the formations were conducted to outline the parts that could be concentrated at % in. (3 mesh). Operators agreed on this size because anything finer required sintering or other agglomeration processes. At 3 mesh only the structural features, as defined above, would be liberated. With suitable ores concentration was easy, as any of the gravity methods could be used. Sink-and-float gave good results, but with this method only limited portions of the iron formations yielded a desilrable product.1,2 n general, the iroa content could be raised to shipping grade, but the silica content remained too high—sometimes 20 pct—instead of 9 or 10 pct. Grinding did not greatly increase the liberation ofsilica until 2010 mesh or finer was reached. To find the reason fpr this T. M. Broderick began micros~opic examin&apos;ations of the formations in 1933.3 Procedure: The purpose of this discussion is to correlate the appearance of typical portions of the iron formations with their amenability to concentration. As liberation is essential before separation becomes possible, much of the work is based on measuring the liberation achieved by crushing and grinding. Both heavy media and magnetic tube tests were used in this work. On the basis of general structural features such as banding, degree of alteration, and leaching, a specimen was selected from each part of the iron formations studied. The specimen represents the gross features of the formation and not necessarily the particular formation quantitatively. One half of the specimen was polished for macro-study, and the remainder was used for analyses to obtain the grades represented by variations appearing in the macrosection. Specimens for microscopic examination were also prepared for each variation in gross appearance. For correlation of microstructure with liberation, the previous work by sink-and-float methods was supplemented by magnetizing roasting followed by magnetic separation. The results show the liberation of silica to be very important at the sizes used, because any silica particle with iron minerals occluded would be held in the concentrate. A magnetizing roast changes the crushing and grinding character of the sample. For partly leached soft samples the change is slight, but with harder types and those in which there is a considerable change in crystal structure of the minerals, the increase in liberation of the iron minerals may be 30 pct more than that of unroasted samples at the same crusheH size. Gogebic Range Iron Formations: The Gogebic Iron Range is located in the extreme western and southern parts of Michigan&apos;s Upper Peninsula, extending westward into Wisconsin. Samples for this study were obtained from the Ironwood formation, comprising three chief members—the Plymouth, Norrie, and Ahvil—with several intermediate slates and thick overlying slates. (The slates are not considered in this discussion because grinding finer than present practice is usually required to liberate the iron minerals.) The predominant iron mineral is hematite, about half of which is hydrated to goe-thite. Limonite occurs in some of the partly leached areas, and siderite in parts of the formation.

Jan 1, 1958

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts &apos; law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott&apos; made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.&apos;1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts&apos; technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By L. A. Rapoport, W. J. Leas, C. W. Carpenter

A program of scaled flow model experiments has been undertaken to study the performance of five-spot water floods. The modeling procedures are discussed and the construction and operation of the flow models are described. The tests were specifically designed to investigate the effects of injection rate and of oil-to-water viscosity ratio on oil recovery. The areal sweep of five-spot water floods was also studied, and direct comparisons between five-spot and linear flooding behavior have been established to permir better utilizatfon of core analysis results for purposes of field waterflood evaluations. INTRODUCTION For a long time reservoir engineering procedures have been confined to the consideration of idealized, one-dimensional or linear systems.11* However, direct application of the linear waterflood mechanism to the evaluation of actual field performance is justifiable only for the purposes of rough approximation. To obtain a realistic analysis of field behavior, it is necessary to account for reservoir geometry and well distribution, and to take into consideration the configuration of the flow of fluids between injection and producing wells. In the past it has been attempted to account for the complex nature of the fluid movement in the reservoir by associating each well pattern with a certain "sweep-efficiency constant", e.g., a sweep efficiency of 72 per cent for the conventional five-spot pattern.&apos; More recently, methods of waterflood evaluation have been improved by the introduction of variable sweep-efficiency factors, defining the areal coverage as a function of cumulative water injection and viscosity or "mobility" &apos; ratio.""&apos; These variable sweep-efficiency factors, derived from miscible fluid displacement experiments, require the assumption of piston-like displacement of oil by water. This implies that only one fluid, either oil or water, is moving at any one point of the reservoir ht any moment. Such an assumption, however, is incompatible with the bulk of the experimental evidence and also theoretical considerations which indicate that usually in the area invaded by water, both oil and water are flowing in varying proportions, in accordance with the relative permeability characteristics of the porous medium. Another recent approach toward the evaluation of five-spot flooding behavior involves correlations of the areal sweep efficiency (observed in immiscible fluid experiments) with a "mobility ratio," based on the consideration of the "average" relative permeability to the displacing fluid. Combination of these correlations with a modification of the Buckley-Leverett frontal-drive equation leads to a computational procedure for predicting the recovery performance of areal water floods. While of considerable interest, this approach has no complete theoretical justification and, therefore, does not entirely clarify the features of five-spot water floods. Rigorous, theoretical treatment of waterflood behavior in two- or three-dimensional systems as encountered in the reservoir, including proper consideration of relative permeability and capillary-pressure functions, is as yet beyond the scope of analytical or computational methods. The, behavior of such water floods can, however, be studied by means of scaled flow model ekperiments, which is the approach followed in these investigations. The flow model experiments described in this paper simulate a uniform, horizontal formation of constant thickness with fully penetrating wells. The system under consideration is entirely liquid saturated and not influenced by compressibility effects, which is representative of the situation achieved after gas fill-up under practical conditions. Gravity segregation effects are assumed to be negligible, which implies a relatively thin reservoir formation and/or low vertical permeability. THEORETICAL CONSIDERATIONS For a flow system of uniform thickness with no appreciable effects of gravity segregation, the analysis of water-oil displacement can be confined to a two-dimensional treatment based on the consideration of a "slice" of unit thickness. Referring to previously established derivations," the displacement of oil by water in such a system can be described by the following, dimen-sionless equations:

By AIME AIME

JOHN ROY THOENEN, supervising engineer of the non-metal mining section of the U. S. Bureau of Mines, was one of the founding fathers of the Industrial Minerals Division. For the first three years of its existence, through 1937, he was its Secretary-Treasurer, and during 1938 serves as its Chairman. Jack was born in Ithaca, Mich., No\,. 8, 1886, attended high school at the Soo, and then spent a year and a half at Michigan State. Apparently this was when the mining bug bit him, for he set out for the Michigan College of Mines. After leaving Houghton in 1907 he tried the motion? picture business for a year and had he stuck to it might have been living in a Hollywood palace by now.

Jan 1, 1938

By D. Ott

Results of a research project on investment or lost wax casting will be presented. The project was concerned with various aspects of the process as they are typical for the production of jewellery from gold alloys. During these investigations testing methods for investment quality as well as for casting quality and the various process parameters were developed and charateristic defects as they occur in practice were traced back to their origin in the process. Investigated were various static casting and centrifugal casting methods in different atmospheres as well as vacuum casting in devices of different design. It was shown that independent of the method a close control of the many process parameters interfering with each other is essential for a quality casting.

Jan 1, 1984

By Owen S. Roberts

During the design phases of a conveyor system, the question arises regarding the type of drive required for each application. The paper shows that the correct drive for any particular application is the one that satisfies the criteria established for that application in the most economical manner consistent with such considerations as site location, availability of spare parts, area environmental conditions, power supplies available, etc. Following discussions of various mechanical arrangements for the drives, motor types and their characteristics are considered along with the control means of modifying these characteristics to satisfy individual requirements. These characteristics are all illustrated graphically. After selecting the motor and its starter, control accessories and interlocking arrangements as applied to material handling systems are discussed.

Jan 1, 1973

By W. L. Doyle

SLAG weights were taken on a series of twenty-eight 6-ton bottom-pour heats. These weights varied from 573 to 1050 lb. Of these, four were chosen for study of the effect of cleaned and uncleaned foundry scrap on the variations of slag weights. Data regarding the make-up and results of the heats are given in Table I. For heat No. 3 the actual slag weight was checked, using the Mn-MnO calculation method-weight 1050 lb. [5,600 X 0.0055 = 30.80 heads and gates 6,000 X 0.004 = 27.00 plate scrap 800 X 0.0083 = 6.64 pig iron 450 X 0.0034 = 1.53 iron ore]

Jan 1, 1947