Search Documents

By C. H. Herty

During the past few years frequent reference has been made to a certain type of iron known generally as "bad iron," "dirty iron," etc., both by steelmakers and producers of iron castings.' Open-hearth operators have claimed that such iron was entirely within the specified limits as to ordinary analysis but it was difficult to make good steel from it. It has been suggested that unreduced material in the iron is responsible, also that most trouble is experienced with the iron when the blast furnace is delivering a product whose analysis is more or less variable. Other reasons suggested are the use of scrap or borings, unsintered flue dust in the burden, a cold hearth, too high a proportion of unsuitable grade of ore, or the form of the carbon in the iron. Accordingly, a subcommittee was appoint at the fall meeting of the Open-hearth Committee of the Americ m Institute of Mining and Metallurgical Engineers held in Pittsburgh in October, 1926, to investigate the reasons for the occurrence of this bad iron and suggest methods for preventing its appearance. This committee enlisted the cooperation of the U. S. Bureau of Mines Experiment Station at Pittsburgh in undertaking a study of pig-iron quality as affecting the open hearth. The following is a report of the findings to date: Method of Testing Inasmuch as a "spell" of dirty iron occurs without warning and may be of short duration, it was deemed advisable to attempt to simulate the conditions existing before and during such a period and compare the quality of the steel made with the normal and with the dirty iron. The Bourne-Fuller Co., of Cleveland, which has a single furnace that supplies

Jan 1, 1929

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,' but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By R. E. Powers, E. H. Kinelski, H. A. Morrissey

A group of 17 American blast-furnace sinters, an American open-hearth sinter, an American iron ore, and a Swedish sinter were used to evaluate testing methods adapted to appraise sinter properties. Statistical calculations were performed on the data to determine correlation coefficients for several sets of sinter properties. Properties of strength and dusting were related to total porosity, slag ratio, and total slag. Reducibility was related to the degree of oxidation of the sinters. THIS report to the American iron and steel industry marks the completion of a 1949 survey of blast-furnace sinter practice sponsored by the Subcommittee on Agglomeration of Fines of the American Iron & Steel Institute. The use of sinter in blast furnaces, sinter properties, raw materials, and sinter plant operation have been reported recently.1,2 After preliminary research and study," test procedures were adapted to appraise the physical and chemical properties of sinter to determine what constitutes a good sinter. During the 1949 to 1950 plant survey each plant submitted a 400-lb grab sample to research personnel at Mellon Institute, Pittsburgh, Pa. A 400-lb sample was also submitted from Sweden. In addition, 2 tons of group 3 fines iron ore were obtained from a Pittsburgh steel plant. The following tests were performed on the iron ore sample and on the 19 sinter samples: chemical analysis; impact test for strength and dusting; reducibility test; surface area measurements, B.E.T. nitrogen adsorption method; S.K. porosity test; Davis tube magnetic analysis; X-ray diffraction analysis for magnetite and hematite; and microstructure. Results of these evaluations are discussed in this paper and supply a critical look at testing procedures used to determine sinter quality. Sinter Tests and Results Each 400-lb grab sample of sinter was secured at a time when it was believed to represent normal production practice at each plant. It was not possible to use the same sampling procedures throughout the survey; consequently samples were taken from blast-furnace bins, cooling tables, and railroad cars. These were very useful for evaluation of test methods, since they were obtained from plants with widely divergent operations. With the exception of Swedish sinter and sinter sample N, which were produced on the Greenawalt type of pans, all survey sinters were produced on the Dwight-Lloyd type of sintering machines. Sinters submitted for test were prepared in identical manner by crushing in a roll crusher (set at 1 in.), mixing, and quartering. To secure specific size fractions for tests, one quarter of the sample was crushed in a jaw crusher and hammer mill to obtain a —10 mesh size. The remainder was screened to obtain specific size fractions. The group 3 fines iron ore was dried and screened and samples were taken from selected screen sizes to be used for various tests. Prior to testing, each ore sample except the —100 mesh fraction was washed with water to remove all fine material and was then dried. This iron ore, a hematitic ore from the Lake Superior region, was used as a base line for comparing results of tests on sinters. The iron ore did not lend itself to impact testing, since it was compacted rather than crushed in the test, and no impact tests are reported. However, the iron ore was subjected to all remaining physical tests to be described. Chemical Analysis: Table I presents chemical analyses performed on the survey sinter samples. Included in this table are data obtained from determination of FeO and the slag relationships: CaO + MgO and total slag (CaO + MgO + SiO, SiO2 + Al2o3 + TiO2). The percentage of FeO was used as an indication of the percentage of magnetite in the sinter. It was believed that slag relationships could be correlated with sinter properties. During initial determination of FeO great disagreement arose among various laboratories, both as to the results and the methods of determining values. Table I lists the values of FeO resulting from the U. S. Steel Corp. method of chemical analysis,' which reports the total FeO soluble in hydrochloric and hydrofluoric acids (metallic iron not removed) with dry ice used to produce the protective atmosphere during digestion. Use of dry ice was a modification required to obtain reproducible results. In this method, the iron silicates and metallic iron are believed to go into solution and are therefore reported as FeO. This is important, for in the study of the microstructure of sinters, glassy constituents suspected of containing FeO as well as crystallized phases of undetermined identity which may also contain FeO have been observed. Strength Test by Impact: In evaluating sinter quality, one of the properties stressed most by blastfurnace operators is strength. This strength may be described as the resistance to breakage during handling of sinter between the sinter plant and the blast-furnace bins. It is also the strength necessary to withstand the burden in the blast-furnace. After

Jan 1, 1955

By R. I. Jaffee, F. C. Holden, H. R. Ogden

Alpha solutes increase the strengths of Ti-Mn alloys through solid-solution strengthening. The substitutional a addition, aluminum, decreases, and the interstitial solutes, carbon and nitrogen, increase the rate of nucleation and growth of a from ß. The best combinations of properties of a-ß alloys are obtained when there is a sufficient quantity of a phase in the structure to dissolve the a solutes. OF the many different titanium-base alloy systems, the predominant alloy type is the a-ß alloy. The properties of the a-ß alloys are dependent on solid-solution strengthening and heat-treatment effects involving the a-ß ratio and transformation reactions. Another variable which influences the mechanical properties of a-ß alloys is the a-stabilizer content of the alloy. An a solute may be present as an intentional addition, such as aluminum, or as an impurity element, such as carbon, oxygen, or nitrogen. It is known that these a stabilizers, when added to titanium, form single-phase alloys which are not heat treatable but which obtain their strength from solid-solution strengthening. Thus, it would be expected that a additions to a-ß alloys would increase the strength of the alloys by solid-solution strengthening of the a phase. In addition, they would affect the transformation kinetics of the ß-to-a reactions and other processes based on the instability of the ß phase. The effects of heat treatment and structure on the mechanical properties of Ti-Mn alloys have been shown in a previous paper.6 This system offers a good base to demonstrate the effects of typical a solutes on the properties of a-ß alloys. The three a solutes described in this work are aluminum, representative of a substitutional a solute, nitrogen, representative of an interstitial a solute, and carbon, representative of an interstitial compound-forming element. The effects of heat treatment and microstructure on the properties of a alloys containing these three elements are described in concurrent publications. Some of these data are used for base-line points in several of the curves used for illustration herein. Experimental Procedures Iodide titanium was used as the base for all of the alloys studied in this work. The alloys were prepared as ½ lb ingots by double arc melting in an argon atmosphere. The ingots were forged to ¾ in. rounds, vacuum annealed for 6 hr at 900°C at a pressure of 10 ' to 10-5 mm of Hg to remove hydrogen, and hot swaged to 1/4 in. diam rod. After me- chanical descaling, test specimens were prepared for heat treatment. The alloys used in this study together with the fabrication temperatures are given in Table I. Heat treatments were done in argon. For the most part, the specimens were sealed in Vyeor capsules under a partial pressure of argon. Quenching was accomplished by breaking the capsule under water. Other cooling methods used included oil quench, argon cool (simulated air cool in an argon atmosphere), and furnace cool. The times for the various heat-treating temperatures are given in Table 11. The tests performed on the alloys consisted of tensile tests on ? in. diam specimens, hardness tests, and microimpact tests. Specimen sizes have been adequately described in a previous publication.' The micrographs presented in this paper were taken from specimens cut from the shoulders of broken tensile specimens. Final polishing was done with Linde B on a slow-speed wheel, and the specimens were etched with a 1½ HF — 3½ HNO, solution. Ti-N-Mn Alloys The transformation diagram and microstructures of the Ti-0.1 pct N-Mn alloys used in this investigation are given in Fig. 1. The effect of small nitrogen additions on the binary Ti-Mn diagram is to raise the ß-transus temperature with little effect on the a solubility of manganese. Also, as has been noted previously,' high manganese-content alloys containing nitrogen, when quenched from temperatures high in the ß field, contain a subgrain boundary phase which appears to be nitrogen-rich a. Marten-site is formed when alloys containing less than about

Jan 1, 1956

By M. H. Merriss

Some years ago, at the plant of the Baltimore Copper Smelting & Rolling Co., the receipt of large quantities of copper blister running high in lead, nickel, and arsenic resulted in the formation of a great amount of very foul slag, in the anode furnaces. A typical analysis of this slag was: Gold, oz. per ton......... 0.09 Arsenic, per cent.......... 0.60 Silver, oz. per ton......'.. 13.20 Antimony, per cent........ 0.50 Copper, per cent......... 19.50 Silica, per cent............ 28.30 Lead, per cent........... 11.90 FeO, per cent............. 19.20 Nickel, per cent.......... 4.60 CaO, per cent............. 1.60 The problem was to get out the copper in marketable form, to save the gold, silver, and particularly the nickel, and to get rid of as much as possible of the lead, arsenic, and other elements that were valueless to the Baltimore plant. In a copper refinery that does not take custom material for matte smelting, the usual method is to smelt the anode slag with coke in a reducing furnace, the black copper thus formed being sent back to the anode furnaces; this was the custom at Baltimore. An average anode slag will contain, perhaps, 40 per cent. copper and such small quantities of lead, nickel, etc., that smelting will get rid of most of these impurities in the black-copper furnace slag. To treat such an impure slag in this way, however, would result in a large nickel loss, and would send back to the anode furnaces all the lead and nickel not so lost, where it would be slagged off again and returned to the black-copper furnace as a slag still more concentrated in impurities. The result would probably be a constantly increasing amount of anode slag containing a likewise constantly increasing percentage of impurities. To avoid such a disastrous closed circuit some other process had to be devised. A small multiple-tank room, built for impure copper as an adjunct to the main series electrolytic refinery, was available, so the following standard process was suggested:

Jan 1, 1924

By E. J. Bartosh

In the brief period from November 1936 to September 1937, the Wilmington oil field developed far beyond all expectations. Decline in some wells appears very rapid, but it is too early to draw definite conclusions, as the majority of wells are maintaining very large and steady output. Heavy curtailment in the central area, which has developed the largest wells, makes it impossible to arrive at a satisfactory estimate of decline. The field is producing oil from the Repetto (lower Pliocene) and Puente (upper Miocene) formations, which are of the same age as formations producing at Torrance, El Segundo, del Rey or the marginal fields of the Los Angeles Basin. All of these fields are underlain by schist. The Long Beach field, northeast of Wilmington, is productive throughout 3000 ft. of Repetto-Pliocene series and also approximately 3000 ft. of Miocene formations, whereas at Wilmington only 700 to 800 ft. of Repetto and 2500 ft. of Miocene formations contain oil and gas. This paper gives a brief summary of the history and development of the field to Sept. 15, 1937, showing the subsurface conditions as they exist with the field only partly developed. History of Development The Wilmington oil field, 20 miles due south of Los Angeles, adjacent to Los Angeles harbor and about midway between the cities of San Pedro and Long Beach (Fig. 7), was producing oil as early as 1932 and only came into prominence as a major oil field of Southern California in the fall of 1936, when the General Petroleum Corporation of California completed Terminal well No. 1 from the upper Miocene, at a depth of 3625 ft., for a daily production of 1500 bbl., 20" gravity A.P.I., thereby establishing discovery of the Terminal zone. As early as 1925, or during the close of the development of Torrance oil field, a number of wells were drilled in the Main Street area looking for

Jan 1, 1938

By R. R. Bryan

SINCE the first applications of cyanidation to silver ores about 1906, treatment of ores in the Pachuca district has been entirely by straight cyanidation. Until about the year 1921, Real del Monte removed a sulphide concentrate (largely pyrite) by tabling in the cyanidation grinding circuit. The ores milled prior to the year 1935 were dry ores, ideal for cyanidation, and yielded 90 pct of the silver and 92 pct of the gold. Since 1934 there has been a notable increase in the refractivity to cyanidation of the average ores received by the mill. Tonnages of the former amenable ores have gradually been replaced by tonnages of more refractory ones, so that present average recoveries have fallen to 83 pct of the silver and 90 pct of the gold. During this period there has also been an increase in the content of base metal sulphides' in many of the ores although this increase is not always directly related to the increased refractivity. Since March 1950, the Cia. de Real del Monte has been developing a flotation treatment for some-of its ores before cyanidation. Suitability for flotation is judged not only by the base metal content, but also by the amount of additional recovery of silver and gold made possible by the combined treatment. Selection and segregation of ores most suitable for flotation before cyanidation is a difficult problem for the mines, and the best that can be done is a compromise that leaves much to be desired. Development of Pre-cyanidation Flotation at Real del Monte Much laboratory work has been done on flotation of ores from the Pachuca district, however, the data could not supply reliable information on the many factors connected with the economics of low-base metal-high silver ores. Pilot plant operations would be required. Pilot plant facilities were made available in March 1950, when it became necessary to close down Loreto's 100 ton per day selective flotation plant because of exhausted ore supply. The results of the 100-ton pilot plant tests indicated that a large part of our tonnage of cyanidation ores could be profitably treated by flotation, and a tonnage of 1100 tons per day was selected as the maximum tonnage of ore that the mines were likely to deliver, and because this tonnage fitted with the grinding capacity of this circuit. Equipment was ordered for the production of a single flotation concentrate. The conception of flotation before cyanidation, at that time, was the production of a single concentrate to be shipped to the lead smelter. The 100-ton pilot plant was immediately increased to 350 tons by installing additional flotation cells.. This. plant was operated continuously until the 1100ton plant was put in operation in January 1951. In July 1950, an increase in the quotation for zinc called for an investigation- of the possibilities of producing a zinc concentrate, and laboratory tests on the tailings from the 350-ton plant indicated that a

Jan 1, 1952

By Hugh H. Waesche

High quality quartz crystals weighing more than 50 grams are required in several important industrial applications.30,31 Primarily, they are the basic raw material for precision, electronic, frequency control components; this includes oscillators and filters in both radio and telephone services. Quartz crystals are also necessary for optical lenses and prisms in special applications requiring high ultraviolet light-transmission as in spectrographs. Quartz wedges are regular components for petrographic microscopes. The application of crystalline quartz as a transducer* in ultrasonic devices has increased in recent years despite strong competition from barium titanate and magnetostrictive [f] devices. Some quartz is fabricated into delay lines for radar. Man has valued quartz for fabrication of art objects since the dawn of history. The art forms were and are painstakingly carved and polished to form intricate figurines, bowls, statuettes, and the well-known crystal balls. The largest known ball, made of perfect quartz from Burma, is now in the National Museum in Washington. It is 12 7/8 in. in diameter and weighs 106 lb 12 oz. Clear, pure quartz chips and small crystals not meeting the electronic-grade dimensional requirements are known by the Brazilian term lasca. They are used to produce fused quartz having wide application in laboratory equipment, as special glasses, for torsion suspension in scientific instruments, and as a source material for growing large artificial quartz crystals 18,35 Electronic applications far exceed all other uses in importance so any discussion of high-quality quartz crystals must be concerned almost exclusively with those functions. Historical Background Because of their ubiquitous character and natural beauty, quartz crystals have long been of interest and known to man. They have been found among early Egyptian and Chinese art forms and the Sumerians are believed to have fashioned seals, beads, and other jewelry from quartz crystals, perhaps 5,000 years ago. Also, American Indians made arrow heads and fashioned some simple objects of different kinds. The origin of the name quartz, although of Greek derivation, is uncertain. The Greeks appropriately applied their word for frozen water or ice, krustallos, to quartz. The present-day, large-scale practical applications of quartz crystals began in 1880-1881 when Pierre and Jacques Curie reported discovery of the "piezoelectric" effect. They found this effect first in Rochelle salt, a common product of grape-wine refineries, while studying crystal symmetry. Piezoelectricity is that property found in certain crystals, including quartz, whereby electrical charges of equal and opposite sign appear on opposite parts of the crystals when they are stressed. If equal and opposite forces are applied to two opposing prism edges of a single untwinned quartz crystal a positive electrical charge will appear on one edge and a negative charge on the other. The amount of the charges will be directly proportional to the force applied. This property seems to be intimately related to pyroelectricity

Jan 1, 1960

By the courtesy of Sir Robert Hadfield, we have received the fol¬lowing communication relating to the development and encouragement of science and research in Germany at present. These statements have been translated by Sir Robert from various German sources, and are presented here as an indication of what Germany is doing not only to further her military power, but also to prepare for the period of trade rehabilitation to which she is looking forward after the close of, the war. KAISER WILHELM TRUST FOR PROMOTION OF WAR SCIENCE The Kaiser has approved the foundation of a Trust with the name given above. The aim of the Trust is to further the development of scientific and technical aids to warfare, by uniting the scientific and the military forces of the country for work together. The scientific Work is to be carried on by the following technical committees (or commissions) (1) Committee for the chemical raw materials, for the production of munitions-manufacturing materials. (2) Committee for chemical war materials (powder, explosives, gas, and the like). (3) Committee for physics, including ballistics, telephony, telegraphy, determination of targets and distances, measurements, and the like. (4) Committee for engineering and communication. (5) Committee for aeronautics. (6) Committee for obtaining and preparation of metals.

Jan 8, 1918

By Stewart L. Toleman, Robert H. Hafner, Irvin R. Kramer

In his paper on the calculation of harden-ability from chemical composition, Gross-mannl discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability—arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium—and to extend the range of composition of some of the elements studied by Grossmann—chromium, copper, manganese, molybdenum, nickel and silicon. Experimental Methods To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (23oo°F.) and forged into rounds of I½ -in. diameter. These bars were normalized twice from 840°C. (I55o°F.) before machining into Jominy bars. mined in most Cases by samples taken from the end-quench hardenability spedmen. AS suggested by Crafts,2 acid-soluble (8

Jan 1, 1944

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

In his paper on the calculation of harden-ability from chemical composition, Gross-mannl discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability—arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium—and to extend the range of composition of some of the elements studied by Grossmann—chromium, copper, manganese, molybdenum, nickel and silicon. Experimental Methods To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (23oo°F.) and forged into rounds of I½ -in. diameter. These bars were normalized twice from 840°C. (I55o°F.) before machining into Jominy bars. mined in most Cases by samples taken from the end-quench hardenability spedmen. AS suggested by Crafts,2 acid-soluble (8

Jan 1, 1944

By Takahide Wakamatsu, Shigeru Mukai

Fundamental investigations were made on the treatment of slime and the chrysocolla flotation, both of which are urgent problems to be solved in copper oxide mineral flotation. Unfavourable effects of slime on flotation are caused by the slime adsorption at the air/liquid Interface as well as the slime coating on the mineral surface. The adsorption of slime at the air/liquid interface was measured by using various kinds of slime particles. As a consequence, goethite, bentonite and talc tended to adsorb markedly at the interface. As a desliming method, slime flotation with a polymer flocculant such as polyethylene-oxide prior to the ordinary copper oxide flotation was found to be effective. The use of both a copper-avid organic reagent and an alkyl xanthate was examined for a selective collection of chrysocolla through xanthate adsorption tests, chrysocolla float- abllity tests and flotation tests for synthetic and natural ore. The copper-avid reagents used were salicylaldoxime, 8- hydroxyquinollne and benzoin-a-oxime. As a result, the ad- sorption of higher xanthate such as amyl xanthate on chrysocolla as well as the chrysocolla-to-air bubble attachment was increased by the presence of a copper-avid reagent under suitable reagent addition and pH of pulp. Flotation tests for synthetic and natural ores confirmed that chrysocolla could be floated sufficiently and selectively with a copper- avid reagent like 8-hydroxyquinoline or salicylaldoxime with its subsequent collection by amyl xanthate.

Jan 1, 1976

By Rodolfo V. de la Cruz

The accurate assessment of the in situ deformability of rock masses is very important in the de and construction of underground openings for mining and geotechnical engineering applications. This paper presents a method and device for determining the in situ deformability of rock masses by relating the borehole jack load to the diametral displacements at a number of orientations around the borehole wall. The method called mu1tiple measurement method include the steps in which: a) diametral displacement sensors are installed at different orientations around the borehole to measure the changes in length of various diameters of the borehole; b) a uniaxial load is applied on two opposed octants of the borehole wall, and; c) using elastic theory and assuming a reasonable value for the Poisson's Ratio of the rock mass, the in situ deformability of the surrounding rock materials is determined from the measured diametral displacements and applied unidirectional load. The multiple measurement method has a significant advantage over existing methods since it provides several independent data in a single test from which to calculate the in situ deformability of the rock mass. The multiple data provide a check and counter check on the reliability and accuracy of the various measurements. The multiple data would also provide a means of quantifying the degree of fissuring on the borehole wall. Information on the degree of fissuring is very important in numerical modeling of rock masses.

Jan 1, 1984

By J. R. Finlay

Every business man who has reached the age of forty, or perhaps even thirty, must know from his own experience that there are occasional periods of "good times'' and others of "bad times "-booms and panics. Those who give to business some complexion of science have invented a semiscientific name for these alternations-the business cycle-indicating that it is a normal phenomenon which by its own nature repeats itself. The longer one lives and the more one enlarges his own experience by the study of history, the more of these cycles he knows and the more disposed he becomes to take their recurrence for granted. If these alternations can be put into the category of common- places, why not treat them as such? We are in a sharp depression right now, why worry about it? Is there not a certain average value for business that can be depended upon in spite of depressions? By way of rejoinder one might answer that war is the great commonplace of history, but when we get into one we generally find it worthy of attention. In the present case, many a man has lost two-thirds of his income, and he is extremely nervous about finding it again. The Southern Pacific Railroad earnings have dropped 75 per cent in the past year; Pennsylvania, 60 per cent; United States Steel Corp., about the same. The drop in current earnings is

Jan 1, 1932

By O. N. Carlson, K. E. Solie

The brittle-ductile transition temperatures of single and poly crystalline chromium metal were studied as a function of nitrogen concentration and chromium nitride distribution. It was observed that In recent years there has been an increasing interest in chromium-base alloys for high-temperature applications. The principal disadvantages, however, have been the difficulties of fabrication and the design problems associated with a material of such limited ductility. Various studies have been the effects noted in the poly crystalline material are essentially reversed in the single crystals. These observations are discussed in terms of existing theories for the brittleness of chromium. conducted recently directed toward a determination of the cause of this brittleness and to find ways for minimizing its effects. Allen et al.,' Wain Abrahamson and rant,' and weaver4 have carried out studies on the effects of interstitial impurities on the brittle-ductile transition of chromium metal of various degrees of purity. These investigations have shown that oxygen has little or no effect on the transition temperature of chromium in all conditions studied but that carbon increases the transition temperature under all conditions tested. Nitrogen was found to increase the transition temperature in the wrought condition and in the quenched or cast conditionS but reportedly has no effect in the furnace-cooled condition.

Jan 1, 1964

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By J. B. Reed, T. A. Read, H. Rosenthal

Although the season cracking of brass has been a subject of experimental investigation for more than thirty years, the mechanism that is responsible for this phenomenon is still obscure. While at- tempts to elucidate the stress-corrosion cracking of some alloys have been relatively successful, the principal accomplishments made in the studies of the season cracking of brass have consisted of improved techniques for the fabrication of articles of alpha brass, which reduce the danger of season-cracking failure in service. The primary purpose of the present paper is to collect the published experimental data which appear to be of importance to the development of an adequate theory of the mechanism of the season cracking of brass. Some of the possible mechanisms which have been proposed will also be discussed, together with some promising avenues of future attack on the problems. Several excellent survey papers on season cracking are available, including the recent ones by Croft and Sachs(1)2 and by Gibbs(2). The principal facts concerning season cracking, as presented in these papers, may be summarized as follows. The season cracking of alpha brass is a special type of stress-corrosion failure, which may occur in atmospheres containing ammonia, air, and water vapor. The stress causing failure may be either the

Jan 1, 1945

By R. F. Campbell, R. F. Miller

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By R. F. Campbell, R. F. Miller

SIXTEEN steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- [ ] atures. Diagrams summarizing the structures and hardness resulting from these two cooling rates are presented (Figs. 3, 4, 7).† Data were also obtained on the influence of these two elements, individually and in combination, on the depth 0f decarburization observed after furnace cooling (Fig. 8). COMPOSITION OF MATERIAL The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 25-ton Heroult electric-arc furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- [ ] tric induction furnace. The cast ingots were hot-rolled to I.75-in. bars. AIR-COOLED SERIES The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to I830°F. (1000°C.) for 20 min. and oil quenching. They were then reheated to I740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1941

By Irwin Roman

In addition to projects such as those reported in parts I and II above, the Section of Geo-physics of the Federal Government has undertaken a considerable amount of fundamental research. Two such field-projects may be mentioned, one a magnetometric study in the Comstock Dis-trict of Nevada, and the other a resistivity-study of snow and ice. In addition to the field-problems, there have been two classes of research of a mathematical type. One of these has been the preparation of tables, scales, and charts for the important geophysical functions already known; the other has been the extension of the relations involved in the resistivity-problem. The magnetometric study at Spring Valley, in the Comstock District, was made for the pur-pose of determining the value of the magnetometer in extending the knowledge of a region, as ob-tained by purely geological means. The variations in the vertical magnetic intensity were mea-sured with an Askania balance at intervals of 20 feet, along lines as shown in Figure I.. These lines were 100 or 500 feet apart over an area approximately a rectangle 6000 by 7500 feet. In addition to the lines shown, two areas were selected for more intensive study. In one, short

Jan 1, 1940