Search Documents

By AIME AIME

S ULFURIC acid made in the United States during the last four years has averaged approximately 7,000,000 tons of 50" B6 acid a year. This is double the production of the year 1913. About 66 per cent of the acid is made from sulfur, 16 per cent from pyrite, 13 per cent at copper, lead, and zinc smelters, and the remainder from miscellaneous sources it her the chamber process or the contact process, (at some plants both) is used. In 1923, the contact process accounted for nearly 30 per cent of all the sulfuric acid made in this country and since then it has been increasingly employed. It was first introduced here in 1898, and has always .proved less expensive than the chamber process for the manufacture of .acid of high concentration and purity, but the latter produces acid of low strength suitable for many industries.

Jan 1, 1929

By E. H. Wells, A. Andreas

New Mexico retained its position as the sixth largest oil-producing state for the year 1937 with a total production of 38,484,630 bbl. This was an increase of 11,680,184 bbl. over the 1936 production of 26,804,446 bbl., or a gain of 43 per cent. The production for Lea County during 1937 was 35,961,056 bbl.; for Eddy County, 2,136,251 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 387,323 bbl. The average daily non-marginal well allowable for Lea County on Jan. 1, 1937, was 92 bbl.; at the close of the year it was 67 bbl. The average daily pipe-line runs were less than the allocations of the New Mexico Oil Conservation Commission, but slightly in excess of the state allowables recommended by the United States Bureau of Mines. The average daily production for the year was 105,437 barrels. The total number of completions in the state was 742, of which 638 were oil wells; 19 hydrocarbon gas wells; 5 carbon dioxide gas wells and 80 dry holes. Of the dry holes, 46 were in proven fields. Of these 46 dry holes, 13 were in the Artesia-Grayburg-Jackson-Maljamar area, Eddy County, two in the Getty Extension field, Eddy County, 11 in the Red Mountain field, McKinley County, three in the Rattlesnake field, San Juan County, and nine in the Aztec-Bloomfield area, San Juan County. There were only eight dry holes in the proven fields in Lea County. Southeastern New Mexico Lea County.—The Monument field was the largest producing field in Lea County, with 10,945,788 bbl., closely followed by the Eunice field with 10,927,929 bbl. The Hobbs field, formerly the largest producing field in Lea County, was relegated to third .place, with 7,292,522 barrels. Drjlling during the year closed the gap between the northern part of the Eunice field and the southern part of the Monument field. The wells in this area were relatively small, because of decreased porosity in the lime. The greatest activity in Lea County was in the Monument pool, with 199 completions, 197 being oil wells, one a gas well and one a dry hole.

Jan 1, 1938

By Kyle Wightman

INTRODUCTION CRA Limited is the largest mining group in Australia by value of sales and the second largest company in Australia in terms of share market capitalisation. In the past 25 years, CRA, its predecessors and affiliates have been involved in a number of mining and further processing developments in Australia and elsewhere. Many of these have been financed using project financing techniques. These include Comalco's development of the Weipa bauxite deposits in Northern Queensland in the late 1950's, the Hamersley iron ore developments in the Pilbara region of Western Australia in the mid 1960's, the Queensland Alumina Limited alumina refinery in Gladstone, Queensland, at about the same time, and the Bougainville copper project in 1969/70. In the past three years CRA has again utilised project financing techniques to fund its Tarong steaming coal project in Queensland, the Blair Athol steaming coal project also in that State and CRA's interest in the Argyle diamond project in the Kimberley region of Western Austrlia. PROJECT FINANCE DEFINED Nevitt Definition Nevitt's is the most frequently quoted definition - "A financing of a particular economic unit in which a lender is satisfied to look initially to the cash flows and earnings of the economic unit as the source of funds from which a loan will be repaid and to the assets of the economic unit as collateral for the loan." Risk and Balance Sheet Treatment It is important to focus in more detail on two aspects of project financing, risk and balance sheet treatment. The assessment of the various elements of risk in a project and the sharing of that risk between sponsors and lenders is the most critical feature. At one end of the spectrum is full absorption of risk by the sponsor(s). This can be described as "on risk" or "on credit" or "full recourse" to the sponsor(s) and is effectively a corporate financing. At the other end of the spectrum the lenders absorb the whole risk in a non-recourse financing which is "off risk" or "off credit" for the sponsor. The other aspect is the sponsor's balance sheet treatment. If the balance sheet of the economic unit undertaking the project and the financing need not be consolidated into the balance sheet of the sponsor (because ownership does not exceed 50%) then the financing may be described as off-¬balance sheet. If consolidation is required then the financing is described as on-balance sheet. Most project financings involve some recourse to the sponsor, i.e. they are limited recourse. Very few are non-recourse or off credit to the sponsor. Limited recourse financings may be on-balance sheet although many may also be off-balance sheet insofar as consolidation is concerned. However, sponsor support may very well be a contingent liability to the sponsor and require disclosure by way of note to the balance sheet should consolidation not be required. CORPORATE FINANCE CONTRASTED A financing which is on credit or full recourse to the sponsor, whether it is directly borrowed or guaranteed by that sponsor, is a corporate financing. Lenders will tend to base their credit assessment on a historical assessment of the sponsor's activities and its financial results rather than an assessment of the project or a detailed assessment of the future activities and prospects of the sponsor. PROJECT FINANCE - A BORROWER'S PERCEPTION Although CRA could choose to arrange all finance on a corporate basis (except perhaps for the very largest projects or acquisitions), project financing techniques provide a number of specific advantages which CRA has noted and which should be carefully considered by a project sponsor. Advantages

Jan 1, 1985

Jan 1, 1967

By F. F. Hintze

Petroleum production in the Rocky Mountain district during 1929 registered a small decline from that of the previous year, conforming with a gradual decrease in the amount of oil produced during the last few years. A number of causes may be mentioned to account for this result, chiefly overproduction in other regions and the apparent desire of operators in this territory to conform to the policy of proration and retrenchment adopted by special agreement among operators in many of the fields. Unit operation has been adopted to control oil production from the Sundance sands in the Salt Creek field, Wyoming, in line with the general effort to stabilize this phase of the industry and prevent excessive drilling of new wells. Another factor which greatly retarded development in the Rocky Mountain region was the executive order of President Hoover issued in March refusing the award of new prospecting permits to future applicants and threatening cancellation of all existing permits upon which actual drilling had not been done as specified by law. Only four states in the Rocky Mountain region are important oil producers. In 1929 Wyoming led with an average daily output of 52,600 bbl., followed by Montana, with 10,730 bbl.; Colorado, with 6500 bbl., and New Mexico with 2700 bbl. daily average. These states bear the following percentage relation to total production in the Rocky Mountain district: Wyoming, 72; Montana, 15; Colorado, 9; New Mexico, 4., (Table 1.) The total average daily production was approximately 73,000 bbl. and the total production of all four states during the year was 26,534,606 bbl. This is 2.7 per cent. of the total oil production of the United States during this period. Colorado Although Colorado is not a large producer of oil and natural gas, its oil operations are widely distributed over the state. The Florence field is one of the oldest oil fields in the country, and there are good reasons for believing that the state will retain its place for many years to

Jan 1, 1930

By H. S. Munroe

The dressing-works of the St. Joseph Lead Company were destroyed by fire, February 26th, 1883. Within about four months, or on July 5th, 1883, the new mill, with a capacity of 500 tons per day, was built and in active operation. The capacity of the new mill has since been increased to 800 tons per day. The old mill was built in 1867, by Mr. C. B. Parsons, the present superintendent. It was a curious rambling old structure, which had grown with the demands of the business; a few jigs having been added in one place, a table or two in another and wings and sheds added to the main buildings, from time to time, as it was found necessary to increase the efficiency or the capacity of the mill. The old mill was, moreover, a most interesting place to the student, a perfect "museum of ore-dressing." Nearly every form of dressing apparatus known to the art had, at one time or another, found a place under its roof, jigs of many kinds, concave, convex, side-bump and stationary tables, tyes, buddles, dolly-tubs, etc., etc. The method of dressing followed in the main the lines of English practice, but with many modifications, both in the machinery and the methods of working, due to the inventive genius of Mr. Parsons. Different forms of crushing apparatus were tried, and the best method of handling the ore and the different products of

Jan 1, 1889

By K. A. Grange, W. S. Holt, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, E. T. Tkac, R. A. Grange

QUANTITATIVE knowledge of the time element involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 135-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Ae3 and Ae1), the temperature range of martensite formation, and the end-quench hardenability. These data are directly applicable to the heat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. MATERIAL All specimens were prepared from a 13-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: Mn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, i.57: MO, 0.36: Al, 1.26. The forged bar was normalized from 1750°F (955°C) and then tempered for one hour at 1200°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. EQUILIBRIUM TRANSFORMATION TEMPERATURES In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Ae3, and the maximum temperature at which austenite is completely unstable, Ae1, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1946

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By J. C. Fisher

Nucleation theory is applied to martensite nucleation in substitutional iron alloys. Composition fluctuations are neglected, and a steady rate of nucleation is predicted for any composition and temperature. The maximum rate of nucleation (as a function of temperature) is shown to be measurable only for on extremely narrow composition range, being too great or too small outside this range. A number of experimental observations, including completely isothermal transformation in some alloys and composition-dependence of M. temperature in others, are compared with the calculated behavior. IN a previous report,¹ nucleation theory was applied to the formation of isothermal martensite in an Fe-Ni-Mn alloy. The experimental observations of Cech and Hollomon² were accounted for quantitatively. It now is of interest to examine the predictions of nucleation theory with respect to martensite transformation in substitutional iron alloys of other compositions. Since Fe-Ni alloys have received considerable attention, both as to their transformation kinetics and their free energies, they will be treated in detail, although the results apply with equal validity to other substitutional alloys. In substitutional alloys, where composition fluctuations can be neglected in volumes of critical nuclear size, the rate of nucleation of martensite in subcooled austenite is¹ n - Nv exp (—W*/kT) [I] where the free energy of formation of the critical size nucleus is W* = 8192 p (?² s³) [2] In the expressions for n and W*, the symbols have the following meanings: N is the number of atoms per unit volume; v, the atomic vibration frequency; 8, a function of the elastic constants of austenite and the shear angle of martensite; , the austenite/mar-tensite inter facial free energy; and ?fc is the free energy change per unit volume accompanying the transformation. Jones and Pumphrey² have determined the austenite to martensite free energy change as a function of nickel content and temperature for Fe-Ni alloys. Their expression is ?F = 2500 C + 1.25 (1 —C)?FFc cal per mol [3] where C is the atom fraction of nickel, and ?Ffe is the free energy change per unit volume for pure iron as tabulated by Zener4 (or, equivalently, Fisher"). From Eqs. 1 to 3, it is possible to calculate isothermal nucleation rates as a function of temperature and composition for Fe-Ni alloys. The only unknown parameter is (?² s³). The best value of this parameter for Fe-Ni alloys, determined from M. temperatures in a manner to be described shortly, is (?² s³)= 9.92 (10)21 cgs units [4] Taking this value of (?² s³), C-curves for isothermal nucleation were calculated for Fe-Ni alloys of several compositions, and are plotted in Fig. 1. It is evident from Fig. 1 that completely isothermal nucleation of martensite in Fe-Ni alloys can be observed experimentally for only a very narrow range of compositions. Cech and Hollomon find that a nucleation rate of about 10' nuclei per cc per sec is as fast as they can follow dilatometrically, and a rate of about 10-1 nucleus per cc per sec is about the slowest that can be measured conveniently. If the nucleation rate is to lie between the limits 10-1 10 the nickel content of an Fe-Ni alloy must fall in the atomic fraction range 0.299 5 C 5 0.302. Nickel contents lower than 0.299 correspond to nucleation rates too great to follow, and those higher than 0.302 to nucleation rates too slow to measure in a reasonable time.* In view of the narrow corn- position range in which successful isothermal measurements can be made, it is not surprising that only one substitutional alloy has been described' that comes close to being in the proper range.

Jan 1, 1954

By Charles H. Fulton

CHARLES H. FULTON, chairman, presided at the first session of the Mineral Industry Education Division on Wednesday morning. Reporting for the program committee, Edward Steidle, its chairman, pointed out that its function was not to arrange programs for meetings but to plan a program for the Division to follow in the development of its activities. This was appropriately followed by presentation and discussion of his paper, "Basic Trends in Mineral Industries Education," which, being available in printed form, was only presented in oral abstract. Jay A. Carpenter submitted interesting written discussion that was read, in his absence, by A. M. Smith. Most of the morning was devoted to the discussion of the paper, which was too extensive and ranged too widely to attempt to report in much detail. H. T. Mann, H. P. Hammond, Cadwallader Evans, C. H. Fulton, T. T. Read, D. F. McFarland and P. B. Bucky joined in the discussion, Mr. Hammond making a plea for more unification in mineral industry education, saying that in the study he made for the Society for Promotion of Engineering Education about 35 different curricula preparatory to work in the mineral industry were discovered to exist. He felt that most of the needs of the mining industry could he met by men who had had four years of engineering training of good enough basic quality to permit them to advance along special lines. However, there was apparently a growing demand, as reflected by the increasing number of candidates for the Master's degree in engineering, for men with more thorough training in the fundamentals.

Jan 1, 1933

I am much pleased by your presentation of my article and flattered to the extent that the cover design refers to it. Incidentally, as between folks who like to work with words, refer to line 6, second full paragraph, page 773 (August Mining Engineering) Would "for" preceding technological have changed the percentages in lines two and three of the bold-face heading on page 770? The intent was coequality among three, (studies of mankind, of science, and of technological empirics). Thirty-three pct for "man" studies is a pretty big bite for engineering schoolmen; 50 pct they won't even examine, let alone nibble at. Arthur F. Taggart For those of you without a copy of the August issue handy, the sentence referred to read: The plea herein is to make the overall time allotment for studies of mankind coequal with those, for science and technological empirics.... Professor Taggart suggests that insertion of the word "for" would clarify the intent of coequality among three divisions of study: The plea herein is ... for studies of mankind coequal with those for science and (for) technological empirics. Editor.

Jan 1, 1952

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10

Jan 1, 1923

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9

Jan 1, 1923

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80

Jan 1, 1923

Jan 1, 1969

By H. L. Hazen

THIS is the story of the recent operations of the Standard Cyaniding Co., which owns the Standard mine, a low-grade gold property in sight of Highway 40 about thirty miles from Lovelock toward Winnemucca, Nev. The ore is mined by power shovel and cyanided after grinding to only 3/S in. A total direct cost of $1.24 was attained in 1941 on 600 tons a day. Mining operations ceased, under Government edict, in 1942, and only in recent months have been resumed. The operating difficulties of today are: (1) the high cost of supplies; (2) labor problems; and (3) Federal laws as interpreted and enforced by executive bureaus of the Government. Of these, the increased cost of supplies is the least important.

Jan 1, 1947