Search Documents

By W. M. Peirce

COAL'S importance in the metallurgy of zinc may be gauged by the fact that approximately a million and a half tons is so employed annually in the United States. This brief paper will show in what way the various steps in the treatment of zinc ores utilize this fuel, either in its primary form or as coke or gas, and to what extent. The first step in zinc metallurgy that requires the use of fuel is roasting the sulphide ore, which is the type of ore in which zinc commonly occurs. Since the roasting is nearly or completely autogenous, however, this use of fuel is too minor to warrant further attention. Concentration of zinc ores is usually carried out by conventional milling methods, but a pyrometallurgical method, the Waelz process, is used to concentrate certain low-grade ores, and to recover the zinc content of certain residues in concentrate form. The Waelz process uses a continuous rotary kiln in which a mixture of coal and zinc-bearing material is heated to a

Jan 1, 1948

By B. W. Roberts, V. A. Phillips

A copper alloy containing- 25.5 at, pct Zn and 19.0 at. pct Ni, which was previously found to show an anoma1old.s hardening effect on quenching- from 600 "C and aging- at 400oc, has now been examined by neutron diffraction. No evidence of long-range order was found. The aged sample showed diffuse scattering- consistent with clustering. The anomalous hardening effect is now attributed to lattice strains caused by clustering rather than (long-range) order hardening. SOLID-solution Cu-Ni-Zn alloys (the commercial 'nickel silvers") have been reported to show anomalies in: change of resistivity on cold working,1-6 temperature coefficient of resistance,2-12 resistivity at low temperatures,13,14 parameter (vs temperature),2"4 calorimetric data,2,4 specific heat,15,16 dilation,2-4 and elastic modulus.17 The structure responsible for the anomalies is produced by annealing typically near 400°C and is rather loosely referred to as the ('K-Zustands" (K state), a term coined by Thomas1' who apparently meant simply that the arrangement of atoms on the sites deviated from that expected statistically. Thomas proposed that the K state occurred in a variety of (solid-solution) alloys such as Cu-Ni-Zn, Ni-Cr, Ni-A1, Ni-Cu, Fe-A1, and Fe-Si and is recognized because its formation is strongly temperature-dependent and results in an increase in electrical resistance which can then be decreased by cold working. Later workers on ('nickel silver" have interpreted the K state variously as short-range order, long-range order. or a combination. The present work was prompted by the discovery by Phillips and Jones19 of a substantial hardening effect when an 18 pct "nickel silver" alloy which is fairly close to the Cu2NiZn composition, was reheated in the range 150" to 450 C after previously quenching from 600°C or, alternatively. was slow-cooled from 600°C or above. The phenomenon was attributed to (long-range) order hardening. Due to the similarity in the atomic scattering factors of copper. nickel, and zinc atoms, the ''nickel silvers" are unfavorable for X-ray diffraction studies aimed at detecting ordering. Nevertheless Bialas et a1.,20 using a powder sample containing 47.96 wt pct Cu, 24.03 wt pct Ni, and 27.98 wt pct Zn, slow-cooled from 400" to 200°C taking 500 hr, observed weak super lattice lines. Further unpublished work" using an anomalous dispersion X-ray technique indicates that zinc atoms are regularly ordered at the corner points of the lattice cell, while the nickel and copper atoms are statistically distributed on the remaining sites. Köster 17 also observed X-ray superlattice lines, for example, in an alloy containing 43.5 wt pct Cu, 28.6 wt pct Ni, and 27.9 wt pct Zn superimposed on the basic fcc cell with a = 3.62 kX. He proposed a Cu3Au-type superlattice with the Ll2 structure in which the A sites were statistically occupied by copper and nickel atoms and the B sites by zinc. He adds that substitution must be possible so that zinc atoms partly occupy A sites. Below about 35 pct Cu, Koster had some evidence for a CuAu-type superlattice with the Llo tetragonal fcc structure with a = 3.82 kX, c/a = 0.88 which could be preserved by quenching. This is suggested17722 to correspond to CuNiZn. While the present work was in progress Hirabaya-shi et a1.23 made an independent comprehensive neutron-diffraction study of a single crystal containing 50.05 at. pct Cu, 26.57 at. pct Ni, 0.25 at. pct Mn, 0.13 at. pct Fe, balance zinc. The presence of manganese and iron is surprising since the crystal was supposedly grown from high-purity metals. The homogenized crystal showed evidence of long-range ordering after an anneal of 5 months at about 300°C. Three possible crystal models were proposed. A curious feature of their results23 is that they could not find any neutron-diffraction evidence of ordering in a powdered polycrystalline near-stoichiometric Cu2NiZn alloy. There appears to be some essential difference between a near-stoichiometric Cu2NiZn alloy and one somewhat further off stoichiometry as used by the present authors. Thus Sato14 was able to reproduce the low-temperature resistivity anomaly reported by one of the authors13 on the present alloy if he used a similar composition, but found the normal behavior of the residual resistivity in a near-stoichiometric alloy. satol2 found that the resistivity of a cold-drawn slightly off-stoichiometric alloy increased to a maximum on isothermally annealing at 300°C and then decreased ("over-aged"). Since he could not explain this on the basis of ordering phenomenon, he proposed that zinc atoms were segregating to stacking faults (Suzuki effect) and found etching bands on the surface by replication which were attributed to the widening of faults. Sato suggested14 that the hardening effect observed by Phillips and Jones19 is partly due to the Suzuki effect. EXPERIMENTAL The starting material was 1/4-in.-diam hard-drawn rod of a commercial 18 pct "nickel silver" alloy identical with that used in a previous study by Phillips

Jan 1, 1967

MR. Woo's succinct description of the mining and smelting of silver-lead in Mongolia, with the roasting-and-reduction process and cupellation, has much interest as a picture of methods that not only may have been in use, as he suggests, a thousand years ago, long before the existence of mining schools or chemical laboratories, but probably vary little, if at all, from the practice of prehistoric times, when King Priam's handsome silver vases, cups and bowls were formed. For it is highly improbable that such large objects were made from comparatively rare native silver, and the metal must have been smelted from ore, and most likely in great part from galena,, with cupellation of the lead. Dr. W. A. P. Martin, in his excellent book on the Lore of Cathay, points out that Chinese alchemy is over 2000 years old, antedating the European by at least six centuries; and he infers that the Chinese skill in metallurgy and many branches of practical chemistry owes its origin to " those early devotees of the experimental philosophy who passed their lives among the fumes of the alembic." Those alchemists, however, may have more likely derived some of their leading ideas from the mys terious, and at that time wholly unexplainable results observed in already very ancient metallurgical processes; in which, for example, certain stones were transmuted, as it were, into metals widely divergent in character from their ores, and even silver and gold were obtained from the most unlikely-looking mate rials. It is therefore, in any case, not improbable that the Chinese may have preceded western nations in the discovery of metallurgical methods. At all events, it is now evident that the Japanese acquired these arts from China, the former source of all their higher civilization. My own observation of old-fashioned silver-smelt ing at Hosokura, on the main island of Japan, and about 220

Jan 1, 1903

By Eugene McAuliffe

THE last obtainable figures of the value of the coal mining investment are those contained in the U. S. Census Reports, from data gathered in 1919. The values shown therein and set forth below cover lands and equipment and do not include distribution and marketing facilities. The working capital necessary to meet pay rolls to purchase material and supplies and workmen's compensation insurance are likewise excluded.

Jan 1, 1926

By Freeman Bishop

More than a few discussions are taking place these days among management economists seeking a way out of the dilemma of lower productivity vs. higher labor costs. Most suggestions would be illegal under present antitrust laws. Otherwise interindustry cooperation could be used to divide up some of management's tasks. Or price structures might be tuned to the special machinery and skills of some plants. Both remedies would be under attack almost immediately. There is one other remedy that is getting lots of attention: some form of compromise between management and labor to phase out no longer needed work practices that unions insist shall be retained. Railroads are the national industry suffering the most from this disease, still known as "featherbedding," an epithet coined by the railroaders themselves.

Jan 1, 1971

By M. W. BERNEWITZ

ALL live producers and manufacturers of metals and alloys are investigating new uses for their products. The tin and tin-plate industry is no exception. One-third of all the new tin mined and refined is consumed in making tin plate. Several billions of cans are each year made from tin plate for the preservation of nearly 200 kinds of food. There are more than 500 tin-plate mills or individual stacks in the United States, which country makes more tin plate than all other countries combined and exports large quantities. As much as 1,800,000 tons of till plate has been made in a year in this country, and 28.000 tons of tin has been used in this period for this purpose. In sonic years a third of the till is so consumed; in 1933 it was half of the supply.

Jan 1, 1935

By W. Lawrence Austin

Jan 1, 1884

By Eugene A. Stephenson

THE year 1935 is noteworthy for the superior legislative measures passed by several states. Sincere efforts have been made to establish equity between the various producing tracts in oil and gas fields. Outstanding legislative measures include the New Mexico law, known as Senate Bill No. 79, approved on Feb. 23; the Oklahoma law on April 22; the Texas law on April 30; and the Kansas law, which became effective July 1. Primarily designed to prevent waste, but more or less the direct out- growth of the current excess of potential oil and gas production, these statutes fall in the class of "Proration Laws."

Jan 1, 1935

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By J. J. Gilman

The dependence of ortho kink-band formation on crystal orientation, on temperature, and on the conditions at the ends of a specimen is described. Load-compression curves for crystals that kink are presented. The reversibility of ortho kinking is demonstrated, and motion of kink planes through crystals is shown. Finally, a phenomenological explanation of ortho kink-band formation is given. ORTHO compressive kink bands (Fig. la) were discovered for the case of metals by Orowan,1 and they have been discussed by Jillson2 and in some detail by Hess and Barrett." However, their history in nonmetallic crystals is considerably older. It is not known when they were first observed in mineral crystals, but descriptions of them may be found as early as 1885.* They were sometimes mistaken for twins.6 Mügge seems to have been first to realize their true nature and importance. He reviewed the knowledge of them for a wide variety of crystals: anhydrite, antimonite, kyanite, vivianite, gypsum, mica, graphite, molybdenite, barium bromide, cal-cite, sodium nitrate, and barite. Also, the "twins" observed by Bridgman7 in sapphire crystals resemble kink bands more than twins. The terms ortho and para kink bands have been coined in order to distinguish between two types of kink bands which seem to represent the same geometrical configurations, but which have different origins and sizes. Ortho kink bands are the usual type that form at low loads when zinc crystals are compressed parallel to the basal plane. Para kink bands form at much higher loads in highly deformed crystals. These terms refer to compression phenomena and are not to be confused with analogous tension phenomena such as tensile kink bands and deformation bands. Mügge described the geometry of ortho kink bands quite completely for kyanite crystals, Fig. lc. The geometry observed for cadmium by Orowan1 and for zinc by Hess and Barrett3 is very similar to that described by Mügge. (See Hess and Barrett for a complete discussion.) Mügge associated kinking with bending combined with basal slip. He pointed out that the kink angles

Jan 1, 1955

By Jacques B. Wertz

Both the San Andreas fault complex and the Murray fracture zone are apparently found to be contemporaneous with the Laramide mineralization period. Their compounding effects certainly have disturbed the Texas lineament belt and its components with serious lateral offsets and most probably have been instrumental in allowing intrusives to be emplaced as well as mineralization to accompany these intrusions at some of the fracture intersections. While the main fracture centers can be almost accepted as being structurally linked together, the Texas lineament trend definitely predominates, exerting a prevailing direction to graben (Silver Bell) and to elongated depressions (Bisbee). That this lineament belt also influenced the concomitant mineralization seems a logical inference. The orebodies are generally found at intersections near the most centrally-located intrusive with a distance varying from contiguity to one or two miles. The Southeast Arizona copper province owes its existence primarily to a particularly favorable structural setting of broad semi-continental scope. Thus, various regional structural elements are to be considered as possibly direct or remote cause for the widespread mineralization, although the one or the ones really responsible may never be singled out. There arc three basic regional elements: (1) The north-northwest-trending anticlinorium that diagonally crosses Arizona is quite obvious because many mountain ranges follow this direction. This anti- clinorium, which merges northward into the Wasatch-Jerome Belt, marks a broad zone of weakness where tension seems to prevail. Mineralized trends such as Jerome-San Manuel-Bisbee may give some weight to the economic value of this structural element. (2) Northeast-trending fractures, parallel to the Colorado Mineral Belt (Landwehr, 1967), appear troincident with mineralization as evidenced by the Questa-Grants-Morenci and the Lordsburg- Tyrone-Santa Rita alignments. This structural direction is accepted as one of the most economically significant in the Southwestern United States. (3) The Texas Lineament.

Jan 1, 1970

By Charles Hardy, George D. Cremer

POWDER metallurgy has been established for some time as a novel method for manufacturing a great variety of articles generally specialties that could not be made conveniently by any other method. In this category are such parts as porous hearings cutting tools of sintered carbides, and electrical contacts in which the metallic constituents do not tend to alloy in the proportions employed. The industry, however, is now at a stage where it has begun to manufacture articles that can and have been made by other methods. Thus, powder metallurgy is now preferred technique for the production of numerous machine parts characterized by high strength, accuracy of configuration, and substantial lack of porosity. Manufacture of such machine parts from metal powders has no doubt been stimulated by the war, although the trend in this direction has been apparent for several years. In any case, quantity production of high-density precision pieces by ponder metallurgy is now in full suing in the United States, and such production can and should continue to expand during and after the war.

Jan 1, 1942

By James P. Sloss

A PERMANENT assay office is commonly established as part of the general plant equipment of operating gold and silver properties, but during the development stage of a mine, the cost of such an office is usually so assay work must be done elsewhere. In most instances only a few samples will be taken each day, but if the mine is to be developed scientifically, the analyses of those samples will guide further development. Under such circumstances, the time element in assay returns is important, since the lapse between the taking of the samples and the receipt of results may determine the success or failure of a small-mine operator. The following description of fur-

Jan 1, 1935

By I. R. Kramer

I. R. Kramer (Martin Co.)—In a recent paper Nakada and Chalmers24 reported some observations of effects of surface conditions on the stress-strain curves of aluminum and gold single crystals. It is of interest to compare these observations with the results published previously in this journal and to comment on their general conclusions. In brief, Nakada and Chalmers concluded that the removal of the surface layer of a prestrained specimen lowered the stress-strain curve for aluminum but not that for gold. Further, they concluded that the surface work hardening of aluminum is confined to a depth not more than l0-3 cm. In our results25 published previously, it was pointed out that when prestrained specimens of aluminum and gold were polished to reduce the thickness upon reloading the initial flow stress decreased markedly. Further if a sufficient amount of metal was removed, the yield point failed to appear. With continued application of the load the stress-strain curve became coincident with that of the virgin crystal. We have found this behavior in some 100 determinations to hold consistently for gold, aluminum, and copper in both single and poly-crystalline specimens. The amount of strain required before the curves coincided depends upon the amount of metal removed but it is usually less than 0.01. This type of behavior is the same as that reported for metarecovery by other investigators.29 For aluminum specimens which have been prestrained and then heated to temperatures above 50°C we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen. With respect to Ref. 24 the curves for aluminum are always below that of the virgin curves, while those for gold become coincident. This observation indicates at least for aluminum that the specimens must have been heated to a temperature high enough to cause recovery by an alteration of the internal dislocations. In addition, a recovery would be expected because of the removal of the surface work-hardened layer. Nakada27 had reported that, with his particular apparatus in which a perchloric acid polishing solution was used, the temperature of the specimen increased 65°C. The curves presented in Ref. 24 for gold do not permit one to detect the initial flow stress upon reloading after the surface-removal treatment. In fact, contrary to the method used by Nakada and Chalmers, the change in the stress-strain curve produced by a surface-removal treatment cannot be described in terms of a decrease in stress at strains much higher than that at the initial flow stress because of the coincidence of the curves at the higher strain values. With regard to the depth of the work-hardened surface layer, our data show for aluminum single crystals (7.5 by 0.3 by 0.3 cm) that the initial flow stress remained constant after 12 x 10-3 cm had been removed from the thickness. This depth was independent of the prior strain. For gold crystals this depth is somewhere between 10 x 10-3 and 20 x 10-3 cm. Y. Nakada (author's reply)— Kramer states,28 "for aluminum specimens which have been prestrained and then heated to temperatures above 50°C, we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen." However, Cherian et a1.26 discovered that aluminum polycrystals annealed at 32" and 100°C showed the metarecovery behavior. They showed that the orthorecovery behavior did not appear until the crystals were annealed at 150°C. Kramer suggests28 that the drop in the flow stress of aluminum crystals after the surface removal by electropolishing24 may be due to the recovery caused by the temperature rise which may occur during the electropolishing.27 However, as indirectly stated in Ref. 24, the current density used in these electro -polishing experiments was 0.15 amp per sq cm. According to ref. 27, this current density should cause a temperature rise of only 40°C. This may cause the metarecovery but not the orthorecovery. Furthermore, as stated explicitly in Ref. 24, the surface removal was accomplished by chemical etching as well as by electropolishing. The results were the same for both electropolishing and etching. During the etching, the specimen temperature did not rise above 35°C. Some aluminum crystals were placed in water at 35° C for 30 min. These crystals did not show the decrease in flow stress. Therefore, it is quite clear that the flow-stress drop after the surface removal is not caused by a high-temperature recovery. However, as Kramer points out,28 it is quite possible that the internal dislocation structure may have been altered because of the removal of the highly work-hardened surface layer. However, how much this rearrangement contributes toward the flow-stress decrease is not known at present.

Jan 1, 1965

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By AIME AIME

WITH the recent increase in the price of gold, its economic recovery at depths formerly considered impractical has become a present possibility. Two important difficulties must be met: pressure bursts of the rock, and the reduced efficiency of human labor subjected to the higher temperatures and the increased humidity at the greater depths. In the following abstract of a paper by J. H. Dobson, presented before the South African Institution of Engineers on

Jan 1, 1935

By Robert Leach

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By Theodore Marvin

FOLLOWING the receipt of questionnaires from many parts of the world, the Aviation Committee is completing a review of the use of aviation in mining and petroleum operations. The summary of this study should be available at the 1937 Annual Meeting in New York City, at which time several papers will be presented on specific application of aerial geologizing. From the reports received, there is little question that this air branch of mining is here to stay. Of course, the transportation of personnel arid material continues to merit attention but it is in the division of aerial geologizing that flying is finding its widest, most technical application.

Jan 1, 1937

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By A. U. Seybolt, R. E. Honnemon

THE purpose of this communication is to present activity data of nickel in the Ni-A1 binary system that was obtained for oxidation studies in this system. This data has been calculated from previous aluminum activity data at 1000°C1,2 by two types of Gibbs-Duhem integrations. These results should be of particular current interest to oxidation studies of aluminide coated nickel-base superalloys3 as well as other problems. The aluminum activity of Steiner and Komarek1 is plotted in Fig. 1 as a function of composition in Ni-A1 alloys at 1000°C. The dashed parts of the aluminum curves represent our approximate extrapolations from the directly measured regions. In the terminal solution regions (a and L phases) standard parabolic solution functions of the following form are assumed: where i is the component subscript, Ki is a constant at a fixed temperature, and xi is the atom fraction. The resultant nickel activity curve at 1000° C from the Gibbs-Duhem integration4 of the aluminum data is shown in Fig. 1. The solubility ranges of the phases present in the Ni-A1 binary at 1000°C are also denoted at the bottom of Fig. 1. Corresponding values of the nickel activity, aNi and yNi, are listed in Table I at useful compositional intervals. including phase boundary values. The aNi and yNi data listed in Table I are subject to the uncertainties present in the experimental aluminum activity data1 and to deviations from parabolic solution behavior in the terminal solutions. The errors introduced into aNi and yNi due to the parabolic solution assumption are expected to be relatively small (<20 pct of the values given) in all the phases except the liquid phase. Some deviation from parabolic solution behavior in the liquid phase is indicated

Jan 1, 1970