Search Documents

By A. B. Parsons

This YEAR BOOK, which is sent to every member, contains the roster of officers and the principal standing committees, brief summaries of the proceedings of the Annual Meeting and of the Regional and Divisional meetings, and the necrology for the year 1934. Also are included abstracts of papers published during the year and a classified list of TECHNICAL PUBLICATIONS and CONTRIBUTIONS, as well as an index of all material published by the Institute in 1934 in TRANSACTIONS, in TECHNICAL PUBLICATIONS and CONTRIBGTIONS and in MINING AND METALLURGY, the monthly magazine, the twelve issues' of which contained 98 technical papers Thus 111 small space are gathered together references to all papers, magazines and books printed by the Institute during the year. The papers for the Iron and Steel and Institute of Metals Divisions have been issued as TECHNICAL PUBLICATIONS distributed under the binding of METALS TECHNOLOGY in the months of January, February, April, June, August, September, October, December This plan of distribution will be continued in 1935 for these two groups The publications for the year 1934 include two sponsored by the Institute's special funds. A Manual for Student Associates and Affiliated Student Societies, prepared by the Committee on Student Relations, of which Jay A. Carpenter was Chairman, was published through the courtesy of the Seeley W. Mudd Memorial Fund, and Volume 112 of the TRANSACTIONS, on Milling Methods, assembled by the Committee on Milling Methods, of which Charles E. Locke was Chairman, was financed by the Rocky Mountain Fund The remaining volumes were all TRANSACTIONS, Volumes 107, Petroleum Development and Technology; 108, Coal Division; 109, Metal Mining and Nonmetallic Minerals; 110, Geophysical Prospecting; 111, Institute of Metals Division and 113, Iron and Steel Division

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying tip pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By R. S. Archibald

The subject of this paper is particularly appropriate, since Daniel C. Jackling was active in early exploitation of taconites on the Mesabi Range and contributed greatly to their later economic development. After his success in developing the low grade porphyries in the West he looked for more worlds to conquer, and so undertook the concentration of low grade taconites, from which he hoped to produce commercial ore. Mesabi Iron Co., organized in 1919, actually did produce merchantable sinter from taconites in 1922. The enterprise did not prove commercial at the time, as cost of production was high and the surplus of iron ore in the Lake Superior District already contributed to a low market price, but this same property has since been developed by Reserve Mining Co. The work done by Jackling had much to do with the success of this later venture. Iron ore was first discovered on the Marquette Range in Michigan in 1845. The first ore from this range came from the old Jackson mine in Negaunee in 1848. During these early years this property and others on the Marquette produced limited tonnages for transportation to Lower Lakes and for consumption by charcoal furnaces in the area, where a plentiful supply of hardwoods furnished the charcoal for iron smelting. The Marquette and other ranges tributary to Lake Superior did not produce much ore for transportation to Lower Lakes until the locks at Sault Ste. Marie were constructed, but from the time the first lock at the "Soo" was completed in 1855 these ores were transported through the locks to consumer centers in the East. The Marquette Range has a history of continuous production from 1848 to the present day.

Jan 5, 1959

By J. W. Powell

A Federal statute, enacted several years since, provides for the preparation of a geologic map of the United States. There are three requisites for a geologic map. The first is a suitable base- or surface-map upon which the rock-formations may be platted by means of conventions ; the second is a classification of the rocks and formations, and the third is a system of conventions by which the rocks and formations may be represented on the map. When the work of the Federal bureau created to prepare the geologic map was commenced, a topographic survey of the country was undertaken for the purpose of making maps suitable for the use of geologists in the field and for the representation of the geology; and this work has ever since been continued. The surveys have now extended over about one-fifth of the national domain, and are mapped on a series of atlas-sheets, each constituting a section of the great map of the United States. About 700 of these atlas-sheets are completed. They are in extended use among engineers, miners, prospectors, map-publishers and educators, and are thus widely known; moreover, these base-maps have been exhibited, described and discussed at meetings of the Institute, and thus do not require detailed consideration. Classification of Bocks and Formations. Modern classification is designed to express natural relation. In the beginning of observational science, or natural science, objects were discriminated and grouped by differences and resemblances; but at first the differences and resemblances recognized in the classification were external, even superficia1,'and often confined to single features. Later, groups of features and characteristics, both external and internal, were recognized as the basis of classification ; and of recent years, throughout the entire domain of biology, and to a considerable extent in the kindred sciences, classification is based not

Jan 1, 1893

ONE of the problems that confronts the chronicler of the Porphyry story is to determine the date from which Morenci should be regarded as one of the group. The mines have the distinction of being the first operated in Arizona for copper. A small smelter was in operation as early as 1873 and in the eighties two smelters accounted for a substantial production ranging from 3,000,000 to 6,000,000 lb. per year. The first concentrator was built in 1886, but the ores were principally oxidized, and direct smelting ore still supplied most of the production. As early as 1893, the mining of somewhat leaner porphyry ores, containing copper in the form of the sulphide mineral, chalcocite, was commenced; but these still were of comparatively high grade and the concentrators were plants of 100 to 400 tons daily capacity. Moreover, the backbone of operations was still the production of rich oxidized ores for direct smelting. They assayed 10 to 15 per cent copper and the sulphide milling ores assayed 3 to 4 per cent. A significant comment appears in the Copper Handbook for 1908. Speaking of the Arizona Copper Co., Ltd., which was to become the most important component of the present Morenci enterprise, the editor, Horace Stevens, says: "A tremendous amount of ore is in sight, ore reserves . . . being estimated at 10,370,600 tons . . . " It seems fair to infer from this that the property was not yet regarded as an immense low-grade mine, but that the copper content of perhaps 70 lb, to the ton made an ore of "medium " grade even according to the standards of the time. Although the concentrating ore was typical of that in the porphyry group of mines (except for its greater richness), no one seems to have the least inclination to take from Utah the

Jan 1, 1933

By Edwin Higgins

INTRODUCTION IT is the purpose of this paper to set forth the relation and functions of the various organizations and institutions engaged in the promotion of safety iii the iron mines of the Lake Superior region; also to indicate the value of this work. Ten to 15 years ago there was practically no organized safety work; the accident rate was high, excessively so in some districts, and dangerous practices and conditions existed in many of the mines. During recent years, however, a gradual change for the better has been made. The chief causes of this change have been (a) public opinion, which has set the stamp of disapproval on the disregard for human life; (b) certain State laws which have made the operators responsible in dollars and cents for injuries to workmen; and (c) the humanitarian attitude of many of the operators, who have always decried the great loss of life in the mines. Today the Lake Superior region as a whole stands second to no other metal-mining district in the United States in its efforts to promote the welfare and safety of the miner. Dangerous practices in and about the mines are fast disappearing. The operators are ready and eager to adopt any expedient, rule, or device that holds forth a reasonable promise of reducing the hazards of the miner. Today the value of a mine captain or shift boss is reckoned, not alone on his ability to "get the ore," but also on his capacity for reducing accidents. While the progress made has been remarkable, there still remains much to be done, for the accident records of the Lake Superior iron mines, while lower than those of the chief metal-mining regions of the United States, still compare unfavorably with those of the metal mines of practically all foreign countries.

Jan 10, 1914

IT will be recalled that when educational instruction for the mineral industry began at Freiberg, at the beginning of the eighteenth century, the original aim was to organize and systematize the procedures previously followed by young men in gaining familiarity with the technology then in use. There must have been many other ideas current, even then, as to just what a young man needed to learn in order to become capable of assuming responsibility for the supervision and direction of such technical work. The problem in Europe was decidedly different from that in nineteenth-century America, because some of the European mines were actually owned and operated by the governing authority and the others were supervised, regulated, and taxed by it. The American problem was the efficient performance of technical operations; the European one was regulatory supervision. It was natural, therefore, that in the development of educational processes in Europe stress was laid on those factors which conserved and protected the interests of the state. The study of mineralogy and geology, leading to correct judgments as to the workability and value of mineral deposits; assaying, which gave the means of quantitative measurements, as did surveying; chemistry, which furnished a better basis of understanding for assaying, mineralogy, and geology; and physics and mathematics, which are the bases for the understanding and efficient use of mechanical appliances, became the core of systematic instruction for the mineral industry. It was early recognized that men could learn more than was already known about all of these subjects and education took on that dichotomy which still characterizes it; the teaching of established knowledge to the unlearned, and that of extending of the bounds of knowledge, now loosely termed research, which after two and a half centuries of work still shows

Jan 1, 1941

Joseph E. Thropp, Jr., Indiana Harbor, Ind.:—To what do you attribute the fact that in some localities the by-product coke sells at a premium over the ordinary bee-hive coke for foundry use ? If the cell-structure is preferably soft and rather thick in coke for foundry use, as I understand it, do you mean that by-product coke has soft and thick cell-walls ? William H. Blauvelt, Syracuse, N. Y.:—As I say in one of the paragraphs of my paper, the tendency seems to be towards the manufacture of foundry- and furnace-coke under somewhat different conditions. The development of the best cell-structure in coke, of course, has not reached perfection, but we are making progress, and we are inclined to believe that under ordinary conditions the best furnace-coke, that is, coke with the hard cell-wall and the well-developed cell, is produced at fast coking-time and high heats, whereas the best foundry-coke seems to be produced at somewhat lower heats. In one of our plants we are making furnace-coke in 16-hr. coking-time, and foundry-coke in 20-hr. time. Foundry-men want the strong, tough coke. I think the furnace-men present will agree that the best furnace-practice requires a hard coke, with a well-developed cell-structure. Replying to the question as to the reason for higher prices being realized for by-product foundry-coke than for bee-hive coke, of course, the immediate reason is that it suits the foundry-men better. Perhaps one cause may be that we are able, by the selection of coals, which is not usually practicable at bee-hive plants, to get a quality and analysis best suited to foundry-work, with high carbon-content, and with cell-structure and physical strength especially suited to the foundry-men's ideas.

Jan 1, 1913

By R. J. Watson

IN an earlier paper, Ehrenburg and Watson1 published the develop-ment for a potential function by which it is possible to obtain the electric potential at points on the surface of the ground when a current I passes between two electrodes and the subsoil is composed of parallel, homo-geneous layers. In view of the continued interest in the resistivity method of electrical prospecting, the author has considered it desirable to publish the results of a number of theoretical studies making use of this potential function, and also the results of a considerable number of tests with models designed to show the soundness of the mathematical theory. It is hoped that these results will prove how erroneous the various empirical rules for depth determination may be. It has always seemed puzzling to the author that one can find, in papers published comparatively recently, statements upholding empirical rules for depth determination, and attributing most of the irregularities of resistivity curves to vertical discontinuities in resistivity in the subsoil. It would indeed be fortunate for the geophysical investigator if such a simple rule held. However, numerous investigators have proved both theoretically and by the success of their field work that such a rule does not hold, even by a" rough approximation" in many cases. On the other hand, as is shown in the development to follow; if the underground conditions are favorable it is possible for such empirical rules to give a satisfactory depth determination. Authors should be more careful about making such sweeping state-ments about the accuracy of these empirical rules because the relative simplicity of the field work places the method in the hands of any inter-ested experimenter, and he is likely to become completely disgusted with the method after he has made several obviously wrong interpretations by empirical rules.

Jan 1, 1934

By John C. Loretta

INTRODUCTION Organizations that regularly use project management services will almost certainly have their own views on the preferred systems and procedures. This chapter, therefore, describes Project Management for the personnel of groups not familiar on a regular basis with project management and deals with the basic questions that these groups can be expected to ask, such as: - What is project management? - Why is it needed? Project Management is the planning, implementation and monitoring of the Engineering, Procurement and Construction activities that are necessary to complete the project in the most economic manner. In the case of a crushing and grinding plant, completing the project would mean bringing it into full operat ion. Engineering is the design work for the purpose of producing drawings and technical specifications for Construction together with technical specifications and quantities for Procurement. Procurement is the arranging of con- tracts so that equipment, material and labour are brought as required to the construction site. Construction covers the on-site activities that bring together the components of Engineering and Procurement so as to arrive at a finished plant. Need & Cost Benefits Project Management systems are needed to allow progress and expenditures to be monitored so that any significant deviations from the plan can be identified and the appropriate corrective action taken. In this way, Project Management is able to give continual updated answers to the Owners broad questions. - What am I getting? - What will it cost? - When will it be ready? The need for Project Management is not always immediately apparent, a common belief being that the existence of the three components -Mining Company - Equipment Supplier - Construction Company - is sufficient to get the job done without a formal project management group. This trio

Jan 1, 1982

By M. V. Nevitt

THE Cr,O-type, or P-tungsten, structure having the space group (Oh2— Pm,n) is one of the most widely occurring structures found among the intermediate phases involving transition metals. Including the phases reported here for the first time, the total number of these A,B phases now known is 39. Greenfield and Beck' have correlated the lattice parameters of these phases with the Goldschmidt radius of the close-packed chains of A atoms. Laves' discussed the apparent size of the A and B atoms in this structure. Gel1er" proposed a scheme for reproducing the lattice constants of the phases by the use of a list of effective C.N. 12 radii for the component elements. Reported here is a survey of the A,B combinations which appeared favorable for the stability of the Cr,O-type phase but which, at the time the investigation was begun, either had not been reported upon or had conflicting reports as to the existence of the structure. Seventy systems were investigated, and 8 Cr,,O-type structures were found. Six of these also were reported by other investigators in the interval between the start of this investigation and its completion. This survey yielded information as to the influence of the relative sizes of the A and B atoms on the stability of the phase and, for the various families of Cr,O-type phases, the effects of the sizes of the A and B atoms on the lattice constant. Likewise, a somewhat clearer picture of the connection between the position of the A and B elements in the Periodic Table and their Cr,O-type phase-forming tendencies has become apparent. Experimental Procedure Alloys were prepared in the form of arc-melted 3-gram buttons in all cases where the vapor pressure of neither component was high enough to cause

Jan 1, 1959

By Lyall Zickrick

Experiments of previous investigations have indicated that calcium-copper alloy, when used as a deoxidizer for molten copper, results in a sound copper casting of good physical and electrical properties. Braden-berg and Wiensl have obtained successful results in casting sound copper using calcium for deoxidizing. Masing2 has obtained deoxidized copper of high density and high conductivity by use of calcium. Pratt,3 in 1907, patented the use of calcium for the deoxidation and degasification of copper. Schumacher, Ellis and Eckel,l in 1929, conducted a series of experiments on deoxidizing copper with calcium. They concluded that so long as there is only a small percentage of residual calcium the mechanical and electrical properties of the copper deoxidized are not impaired, and the deoxidation is thorough. For this investigation, a copper-calcium alloy high in calcium and 10 variously deoxidized copper ingots were prepared. The investigation concerns itself with the casting properties and structure of these variously deoxidized ingots, their working and annealing characteristics, and the resulting physical and electrical properties of the worked materials. Preparation of Special Copper-calcium Alloy and Experimental Ingots For use as a deoxidizing agent, an alloy of copper and calcium with fairly high calcium content was prepared, by melting pure electrolytic copper in a graphite crucible in an ordinary gas-fired pot furnace. The molten copper was kept well covered with calcium chloride slag. Small chunks of calcium were wrapped in thin copper sheet, placed on the end of a graphite rod and plunged down into the molten copper and thoroughly stirred. Upon completion of the calcium additions the crucible content was poured out into a cake about one inch thick. Analysis of this alloy gave 4.4 per cent calcium. The alloy was brittle and easily broken into small chunks. Some calcium was lost during the addition, owing to

Jan 1, 1933

By A. Rosen, P. Wynblatt, J. E. Dorn

The temperature, strain rate, and structure dependence of the flow stress in a poly crystalline Fe-2 pct Mn alloy was investigated between 77" and 370°K. It was possible to identify the low-temperature data from 77° to 160°K with Dorn and Rajnak's theory of the Peierls mechanism of plastic deformation. Above 160°K one or more thermally activated mechanisms must he operative; however, these were not identified in this investigation. The mechanistic basis for the rapid decrease in the flow stress of bcc metals with an increase in temperature over the low-temperature range is yet being debated. Various dislocation mechanisms have been suggested in the past but the agreement between the various proposed theories and the experimental results have not been definitive. In the present paper, the authors will demonstrate that the plastic behavior of polycrystalline iron containing 2 wt pct Mn plus interstitials agrees excellently with predictions based on the Peierls mechanism from 77" to 160°K whereas from 160" to about 370°K other as yet unidentified thermally activated mechanisms take over. Undoubtedly, the overlap of these mechanisms with the Peierls mechanism contributed to the difficulties of rationalizing the low-temperature behavior of iron and its alloys. I) EXPERIMENTAL TECHNIQUES AND RESULTS Although extensive data are now available on the effect of temperature and strain rate on the flow stress of various bcc metals and alloys, it was, nevertheless, deemed necessary for the objectives of the present study to obtain highly accurate data of the type most pertinent for checking the theories on a series of well-documented work-hardened states. Iron containing 2 wt pct Mn was used in this investigation in order to obtain a lower ductile to brittle transition temperature than that for iron.' The additional elements present were 0.004 pct C, 0.05 pct 0, 0.004 pct S, 0.003 pct P, 0.006 pct N, and 0.001 pct Si. The as-received 3/8 by 3/4 in. bars were cold-rolled to 0.100-in. thickness, recrystallized under argon for 30 min at 1073"~, further cold-rolled to 0.063-in. thickness, and finally recrystallized under argon for 30 min at 1000°K. This treatment gave a stable reproducible equiaxed grain structure having an average grain diameter of about 90 p. Prior to the final recrystallization treatment, the sheet was machined into tensile specimens 1/4 in. wide having a 1.625-in.-long gage section. All specimens were tested in controlled-temperature baths on an Instron Testing Machine. For convenience in the theoretical analyses the data will be given in terms of the shear stress for flow, 7, the shear strain rate, f, and the shear strain, y. A series of three standard strain-hardened states were obtained by prestraining specimens at 300°K and at a shear strain rate of 7.68 x lo-' per sec to three stress levels of 6.89 X l08, 10.3 X lo8, and 14.5 x 10' dynes per sq cm, respectively. Immediately following this prestrain the temperature bath was changed and each specimen was pulled in tension at either f = 7.68 X lo-' or f = 3.06 X 10"3 per sec. In terms of the accuracy that was achieved, the values obtained did not deviate more than *0.1 X 10' dynes per sq cm and * 1°K from the reported values of stress and temperature and not more than *5 pct in the reported values of the strain rate. The tensile stresses were converted to shear stresses using a factor of 1/2. The shear stress for the initiation of flow at the test temperature was determined by taking a y = 6.16 x 10'3 offset. from the modulus line at which point good accuracy could be achieved in determining y and the associated flow stress 7, with only a negligible increase in the pre-

Jan 1, 1965

By L. W. Pommier, F. B. Brien

The Rheological properties of pulps are non-Newtonian in character and more than one viscosity parameter is necessary to describe their behavior, therefore, the single term 'apparent viscosity' which has been used in the past may be misleading. The study reported in this paper uses a dimensional analysis based on the Ostwald-de Waele shear stress-rate of shear model for non-Newtonian liquids to develop velocity and resistance equations for falling spheres. An electronic monitoring apparatus was assembled for determining the velocity of metallic bodies as they fall through opaque liquids and suspensions. By means of this apparatus the behavior of the viscosity parameters of the Ostwald-de Waele model and the applicability of the proposed equations were examined for a number of non-Newtonian liquids. The validity of the equations for these liquids was confirmed. Preliminary data collected using solid-liquid suspensions established the validity of the form of the basic equations for these systems. The differential movement of solid particles through solid-liquid pulps and suspensions is very important LO many branches of engineering, such as minerals processing, soil mechanics, ceramic slip processing, oil well drilling-mud technology, materials-handling in pipelines, and many others. There is a dearth of fundamental knowledge on the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The resistance offered by Newtonian liquids to the movement of free settling spheres is well described for laminar and turbulent conditions by Stokes' and Newton's Laws, respectively. However, problems are encountered when attempts are made to extrapolate these simple relationships into solid liquid suspensions. The rheological properties of pulps are such that they are non-Newtonian in character;'" that is, the applied shearing stress and resulting rate-of-shear are related by non-linear functions, and thus, in the simplest case two viscosity parameters are necessary to describe their rheological properties. For this reason the single term 'apparent viscosity' which has been commonly used to explain the flow resistance of suspensions and non-Newtonian liquids may be misleading. It is realized that a rigorous analysis of the rnechanisms of momentum transport of liquid-solid systems is complex indeed. There are many variables that affect the rheological properties of the systems such as density, size, shape, and surface energy of the suspended solid and density and viscosity of suspending liquid, as well as the solid to liquid ratio. However, it was felt that a useful contribution to the knowledge of the behavior of suspensions could be made by examining the systems in terms of the basic fundamentals of nowNewtonian flow. This has led to the development, by means of dimensional analysis, of velocity and resistance equations, using two viscosity parameters to describe the velocity of penetrating bodies and the flow resistance encountered by these bodies, as they pass through non-Newtonian systems. THEORY In order to examine the effects of the rheological properties of solid-liquid suspensions on the movement of immersed bodies it is appropriate to start with non-Newtonian liquids and develop equations, analogous to those of Stokes and Newton, for laminar and turbulent flow respectively, from which quantitative information may be obtained. Further investigation would then be directed at the complex suspension systems, and the effects of the many variables on the velocity and resistance equations. Liquids are classified on a basis of viscosity which may be defined as the relationship between applied shear stress and resulting rate of shear?-'* Pure single phase liquids composed of small light molecules behave as Newtonian liquids, having a single viscosity parameter since the shearing stress and rate-of-shear are related by a linear function. Bingham plastics are similar but have a yield stress. Of particular importance in our investigation are dilatant (shear thickening) and pseudoplastic (shear thinning) non-Newtonian liquids, with and without yield values.

Jan 1, 1968

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By J. E. Gosline

In any theory of a hydrodynamic nature dealing with the vertical flow of gas-liquid mixtures in pipes, the two factors that present the greatest difficulty are the relative motion between the phases and the energy loss resulting from turbulence work. The former has generally been referred to in the literature as "slippage" and the latter as "friction." A third factor of importance is the nature of admixture between liquid and gas for both the relative motion between the phases as well as the turbulence work are functions of the type of mixture. Although much work of a general nature has been performed on the vertical flow problem, there have been very few attempts made to study experimentally the factors involved in the phenomenon individually. Of these, perhaps the most notable is the work of Moore and Wilde1 on slippage. Some writers on the subject have assumed that over a wide range of operating conditions the controlling type of mixture is one in which gas bubbles of uniform size are distributed throughout the liquid, and that the data obtained from experiments on the motion of single bubbles through various liquids may be used in evaluating the slippage. Ver-sluys2 has further assumed another controlling type of mixture in which the liquid occurs as a dispersed phase within the gas and applies data on the fall of drops of water in air to calculating the relative velocity. It was for the purpose of studying the applicability of data on single bubble motion to the slippage factor and to further observe the nature of mixtures that a research program was conducted at the University of California during 1932 and 1933. These experiments formed a basis for

Jan 1, 1936

By G. P. Chatterjee

HARDNESS is one of the most common properties of metals and alloys but is one of the most difficult to define or express in terms of the fundamental units. In the Brinell or Vicker's hardness test, the hardness number N is defined as N = L/A where L is the load in kilograms and A is the area in mm'. This does not necessarily imply that a pressure of N kilograms per mm2 actually acts on the specimen.' It is essential that for a true comparison of hardness values the angle of indentation be kept constant,' a which is not done in the Brinell test. For this and other reasons, the Brinell hardness value is not based on a satisfactory physical concept.' The concept of hardness based on the work done per unit volume of indentation3-6 offers a simple and scientific definition. An attempt has been made here to develop this concept (at constant angle) and to compare the values so obtained with the Bhn for different metals and alloys. In Fig. 1 a vertical load L is applied to a compara- tively hard ball of diameter D creating an indentation of diameter 6 and depth h on the specimen S. The work done, W, is then given by W = So Ldh. [I] Since L is not independent of h, Honda and Takahasip and Matsumura" assumed different functions leading to equations which do not apply equallye to a wide variety of metals and alloys. A better relation is obtained from Meyer's Law L = ad" [2] where A and n are constants depending on the nature of the material but independent of the ball diameter D. From Fig. 1 it is obvious that h = R(l — cosq) and d = 2R sin 8.

Jan 1, 1957